Digital triggering Vs software relaxation.

Similar Questions

• Slope of digital triggering NI SCOPE

  I have a problem, try to use a digital triggering with a USB-5133 digitizer.  I use NO-scope (3.5) and C.  My software doesn't seem to be able to change the slope of the trigger (using niScope_ConfigureTriggerDigital()).  There is no problem if I use an analog trigger.

  The problem is not related to my code.  I see the same behavior with the NOR-SCOPE Soft Front Panel (version 2.9).  In this application, if I connect the trigger PFI 1 entry and select digital triggering, then the selection of the slope has no effect.   However, by selecting briefly "edge" trigger, change of slope in this mode and back to digital triggering, I find that the trigger is now working according to the slope in the edge, trigger mode.

  Although niScope_ConfigureTriggerEdge() seems to work o.k. (using an analog input) and is not niScope_ConfigureTriggerDigital(), the following sequence does not provide a work around:

  niScope_ConfigureTriggerEdge (...);

  niScope_ConfigureTriggerDigital (...);

  The entrance of IFP 1 seems OK, even though at the start I had been feeding it straight V CMOS 5 door.  Adding a separator line at the entrance to the tensions between 0 and 2.8 V had no effect on the behavior.

  Hello Bmetz,

  It is a known problem that has been fixed in version 3.5.1 OR-scope. You can download and install the update through the page drivers and updates here:http://joule.ni.com/nidu/cds/fn/p/sn/n23:3465.40/lang/en

  You will find a list of bug fixes in the readme, including the following:

  123308: Fixed problem
  with incompatible trigger when to change the edge of triggering on the NC
  USB-5132/5133.

  Hope this helps,

  Jennifer O.

  Product Support Engineer: scanners high speed

• Outbreak of the AO tasks with digital triggering

  I'm triggering an analog using a digital triggering (PFI0) task on a NOR-6343 (USB), but don't see the behavior desired of my VI (see screenshot).

  * When I shoot digital triggering (digitalTrigger = False), the AO signals appear planned (except that... they do not fire).

  * When I turn on the trigger (digitalTrigger = True), however, there is no signal on the channels of the AO.

  * I tried two different sources: PFI0 and the clock internal (set both rising edge). For the PFI0 channel, I connected a function with a wave generator square 5 v (the PFI0 had a slow rise... time "I think I could solve this problem by adding a small circuit of buffering). However, I expect it should work correctly using the internal clock as a trigger.

  What's wrong with my code / setup?

  A few follow-up questions:

  * This will trigger the installation program not start indicator AO once? Or the trigger will cause the task to start whenever the finished AO signal and the trigger goes high? (I wish that it behaves like the latter)
  * Just to check: the response rate of the AO task to the digital trigger should be of the order of 1 MHz?

  Hello kllurie,

  What do you use the trigger for? The way you have the task to put in place now, it will run continuously until you press the STOP button and ignore any input trigger. If you want to be able to have the task to complete and start over with a digital triggering, you make the task two finishes and Retriggerable. You can configure the task to be finished by replacing the constant continuous samples on the Timing.vi with finished samples and giving him a number of samples to be taken before stopping. Then you can do the task Retriggerable using the property trigger DAQmx node and choosing Start > more > Retriggerable sometime before the Start.vi.

  As to what it should be used as your relaxation, you'll want something with a fast rise time (so that it is detected as a numerical advantage) and is not as fast as the sample clock. If you use the sample as your trigger clock, there would be essentially no difference between your redeclenchables task and a continuous. It would end the collection of samples and then immediately redeclenchee.

  Let me know if that answers your questions!

• Digital triggering PCI-6024E problem

  In my view, the PCI-6024E is intended to support that integrates digital triggering. However, I get the following message if poster every time I try a digital triggering:

  "Error-200452 is produced in property Node DAQmx trigger (arg 1) in DAQmx Start Trigger (PowerPlay) .vi:1-> relaxing test.vi.

  Possible reasons:

  Vital statistics: Property specified is not supported by the device or is not applicable to the task.

  Property: Start.TrigType

  "Task name: _unnamedTask<245>"

  I'm on 8.9 DAQmx and Labview 8.6.

  I've included the simple vi, I tried to test a digital triggering with where I made some stupid mistakes.

  Thank you!

  Hey Ptuinluff,

  Have a look here for information and an example on how to use another subsystem to allow the trigger to start.  Let me know if you have any questions.

  John S

  Technical sales engineer

  National Instruments

• generate a digital triggering out CH1 (low and high) for the USB-5133

  Hello

  I would like to generate a digital triggering on the USB 5133 CH1, is this possible?  I tried with the PFI 1 successfully but the output is only 3.5 v and I need to 5V, because this trigger signal goes to a box of pulse generates a signal, which is received by the CH0 on the USB-5133. This configuration works on the 5102 OR but because of the treatment, I am obliged to try a new device.

  Channel 0 and 1 are only entries then you will not be able to use them to generate a signal.  All of our products current digitizer that are recommended for new designs use 3.3V CMOS logic levels for PFI lines in output mode.  Your best bet to generate a digital triggering 5V would be to use an external buffer that can accept 3.3V CMOS levels as an input, but is under voltage of 5V.  Here are some that might work for you, but there are many others: http://www.onsemi.com/PowerSolutions/product.do?id=M74VHC1GT126DT1G adding a buffer in line with the trigger signal will add delay, so you will need to ensure that it is acceptable for your application.

  Hope this helps,

  -Matt

• simulateneous of analog and digital triggering

  Hello

  I have an experience that is very similar to this announcement:

  http://forums.NI.com/T5/LabVIEW/how-do-I-reset-the-arm-trigger-with-DAQmx/m-p/2006639/highlight/FALs...

  As in the display, I need trigger out of logic AND low frequency (3 Hz) and a signal of high frequency (100 Hz).  However, my experience is different because my low-frequency signal is an analog of entry (AI0) and I need experience to trigger off each edge of the signal change high frequency, while the analog input is high.  To do this, I created a trigger to HAVE that starts a counter whose state high and low are similar to that of my analog input signal.  I then export the output event from the meter to a port (PFI8) and pass this signal and the other signal high frequency through a door AND as in the posting linked above.

  So far, everything works.  I've included a VI that is just this part.

  However, I then connect the output of this gate AND a PFI0 port and use it as a digital triggering to read an AI0, 1 channel.  When I perform this final step, my whole system stops working, but gives no error.  To troubleshoot, I measured the output of the meter to the port of PFI8 has stopped working and the port of PFI8 remains in the low state.  For some reason any when I add the channel HAVE additional (AI0 or AI1, whatever) with digital trigger (PFI0), everything grinds to stop.  I have also included the VI for this case.

  Any ideas?

  Thank you very much!

  Hi Jared,

  I use indeed a door AND external as described in the thread.   Further research actually led me to discover that "you can't have two analog input tasks at the same time" of this thread:

  http://forums.NI.com/T5/Multifunction-DAQ/multiple-analog-inputs-by-multiple-digital-triggers/TD-p/1...

  So I had to build a circuit to convert my analog signal into TTL signals (for the release).  I then AND'ed the two signals in the same was as described in the thread mentioned above.

  -Clinton

• digital triggering of stop/start of analog data acquisition

  I want to use a signal from a digital line to start and stop analog data acquisition. The signal can change levels several times during a race of the VI so I have to start and stop several times data acquisition and store each session data in a different file.

  I tried to play with the following screw: digital triggering of break, DigitalStartandStopTrigger and ContAcq_DigTrig. None of them doesn't seem to work for my configuration. I also do continuous data acquisition so I can't use a reference. I use PCI 6259 DAQ.

  I used the "P0" pins rather than PFI pin on the grid BNC-2090. I know... stupid enough.

• How can I resize a digital image using software of photo gallery to keep my digital images to be cut during printing on standard paper by a commercial processor? MP

  How can I resize a digital image using software of photo gallery to keep my digital images to be cut during printing on standard paper by a commercial processor? MP

  How can I resize a digital image using software of photo gallery to keep my digital images to be cut during printing on standard paper by a commercial processor? MP

  ====================================
  Sometimes the only resizing is not the answer because the
  the original size is different from the print size.

  You may need to crop photos to the size you want
  print to ensure that no clipping will occur. Cropping
  to a different aspect ratio will lose some parts of the picture but
  at least you have control over it.

  Windows Live Photo Gallery is a cropping tool.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• How to start collecting data through digital triggering entry user GOLD

  Hello

  I have a vi with which I would like to collect data. It is configured to start to perceive when the start trigger is detected, which works perfectly, but I would also create a user can start the process of data collection by pressing a button instead of apply the trigger. I am at a loss on how to do it. I thought that the structure of the event would work well; However, the relaxation has no Boolean value I can associate it with. If that were the case, I could then perform a logical comparison between the trigger and the button to determine if the collection of data should begin.

  So, how can I represent a trigger activated as a Boolean value? Or is there a better way to reach my goal?

  I think I can make things clearer by expressing in linear programming that it is, I'm trying to achieve:

  If (trigger == true: button == true) {}

  begin to collect data

  }

  I have attached my vi where someone feels useful.

  Hello

  You're right, 6229 USB is certainly not compatible with NO-Sync. However, you should be able to do with the DAQmx driver functions.

  If I understand correctly, you want to generate a graph of your analog input and have this file based on a triggered event entry. A line using PFI will not work for this particular function, but you can create a task digital input instead and pass the thread to a D e/s instead of a PFI line line. You can then use for/no-write the analog input file using a case structure depending on the State of the digital line.

  I hope this helps! Let me know if you have any other questions.

• Problem - edges of digital triggering slows down during the fast rotations

  Hi all. I have problem to understand. I want to measure the pressure with two strain gages on 90 degrees (NI 9237 half bridge II) and I engine with metal plate on it with 52 teeth (gear) to measure on each tooth of the strain. For the rotation, I use NI 9401 digital input.

  I need for example 1000 samples from the first digital edge to the second. (on the metal plate). I try to start trigger. In slow speed (turn around with the hand) of the metal plate, everything is OK. But if I turn around the metal plate digital fast triggers edges slows down. During a cycle on the metal plate on the cost of slow speed me 52 digital edges 1000 sampels by edge (metal plate is with 52 teeth), but rely on fast speed on me 25 edges. This problem is sync of the digital inputs and the analog inputs. I made the example with DAqmx Vi express. I've implemented on digital imput and then count me in each tooth regardless of speed and everything is OK, but when I buid trigger of strain on the edges of quick release rotation speed slows down.

  Can someone help me with this?

  Thanks before.

  So you're collecting samples from 1000 to 10000 samples per second. Which takes 100 Ms. If your triggering edges occur more quickly than the interval of 100 ms, some of them will be missed.  If you run faster than a cycle all 5.2 seconds your gear plate with 52 teeth, some triggers will be produced before the end of the previous data collection.

  What is the fastest speed that you will not sping palte metal?

  Lynn

• Digital triggering PFI on a cDAQ-9188

  I use a Campell data recorder to send a pulse of 5mV to my daq to trigger the recording of some accelerometers. I also have the code to stop acquisition when another pulse is sent, the code has currently a predefined sampling time how I would change.

  Thank you very much

  I'm glad that it worked.  You get with the other examples?

  There is a slight difference between the former and the latter. The one you posted just checks for the trigger of the judgment in software rather than in hardware, so you will be limited to verification of the digital line as you take more analog samples.  If it works for you, but then that's fine.

  One thing I would recommend is a stop button, so you can stop the loop if you want, without having to give up the program.  It will ensure that you clear resources etc.

• Generate the AO with digital triggering

  Hello, I have a problem, generate a continuous waveform (custom channels multlisample) when a TTL - as 5V 0V trigger is applied to PFI0. The problem is that synchronization source is running continuously, when the digital voltage line is connected I don't have to keep a single waveform sent, as opposed to a regeneration of the same waveform.

  I have worked with some conditional loops, but nothing works, is there a solution that can provide two triggers (one for a pulse train) and then for the digital falling edge (on 0V) which can allow the regeneration of the writing of the AO?

  Thank you

  DB.

  Hey DB,.

  I recommend using a pause trigger.  This will allow you to exit when a certain level of TTL is high (or low) and not when the opposite is true.  Here is an example that illustrates the break trigger using property DAQmx nodes.

  You need to change the time by continuous for this example sample clock, but also to change the data to be written to fit your application.

  You can leave the writing of the initial value in the analog output channel if you wish, or you can delete the original entry, start and stop functions DAQmx.  Either will work.

  Best,

• Series two E shared digital triggering

  Can it be converted into LabVIEW 2012?

  Yes.  You need to post in the Forum Conversion of Version as I mentioned above.

  You seemed to find your other file you want to convert.

  Version conversion Board was created to prevent disorder in the ordinary Council of LabVIEW for people who are in need of converted files.

• Digital telephony for Mac software

  Where can I download the software for Mac OSX 10.5.8 for digital voice recorder Sony ICD-SX750? Thank you.

  Thank you for your post and welcome to the forum.

  The ICD-SX750 is compatible with Mac OS X (v10.2.8 onward) and you can drag and drop files and import them into iTunes, if necessary, however the Digital Voice Editor software is Windows only.

• Digital Persona software stops working on the Pavilion dv8-1250ea

  Hello!

  I noticed that Digital Persona, the software for the JJUJ scanner integrated on my HP Pavilion dv8-1250ea stops working whenever the laptop wakes from standby or hybernation mode. On the login screen, the icon on the right referring to the fingerprint reader warning flashing at a rate of about twice a second and the following note says "fingerprint reader not detected". So I'll type the password manually, but the cursor in the field password prevents jump at the beginning of the field at the same pace, and it seems as if there is a current discount. The only way to log is press the 'end' key immediately before each character in the password, which is a disappointment.

  I recently downloaded an update for Digital Persona, but it has not solved the problem.

  Any ideas how to fix? Thanks in advance!

  Andrey

  Here is a work around, see if it works... You will need to go to Device Manager, depending on what hardware you have; AuthenTec orvalidity... Double-click on it... who will launch the Properties Windows... Click on tab power management... this tab, uncheck the box that reads "allow the computer to turn off the device to save power"... and see if it works... ' "