Disable the Internet connection for the virtual machine.

Similar Questions

• How to activate the Internet connection on Windows Server 2003 is installed in the virtual machine in VMware Workstation 8?

  I have Windows Server 2003 is installed on a virtual machine in VMware Workstation 8. I need it to learn and practice the use of the Active Directory. I've also set up 3 Windows XP workstations connect to it, which means that they can communicate with Server 2003. What is lacking is the Internet connection on all of them. When I run ping 8.8.8.8 in one of these virtual machines, I get, 'Destination host unreachable.'

  I'm not sure, what if the problem comes from the settings in Windows or the settings of the virtual machine.

  Can someone help me?

  Thank you, guys. I was finally able to put in place. It was quite an ordeal to deal with IP addresses and virtual networks. Here's how I did (in the screenshots) in case someone else needs it.

  (I also confess that it is perhaps one of the ways to implement. Maybe there is an easier way to do it with DHCP...)

  1. in your computer where is installed VMware Workstation 8 begin the "Virtual Network Editor." It is located in the folder of installation of VMware Workstation. And implement the network following (VMnet2 in my case):

  

  2 then in VMware Workstation itself in the virtual machine when Windows Server 2003 is installed set up two network as connections:

  This one is for external access to the Internet:

  

  And this one for intranet communications AD:

  

  3. then in the machine virtual de Windows Server 2003 set up what follows for two network adapters:

  For Internet access:

  

  Then, you need allow this connection to share:

  

  And then for the ad access to workstations (ensure that the static IP address is in the range specified in the virtual network over VMnet2 network editor). I've also set up DNS to 127.0.0.1 because I installed on this Windows 2003 DNS server:

  

  4. from the Windows 2003 VM try ping 8.8.8.8. It should work now.

  5. go to each workstation, in my case, Windows XP, each in its own virtual machine and set up the network in the VMware Workstation as follows:

  

  6. then in the virtual machine, configure the network connection for Windows XP workstation. Don't forget to assign a new static IP address for each workstation, which not coinside with IP of the domain (this IP address must come from the range specified in the virtual network over VMnet2 network editor):

  

  7. try first ping the domain, in my case ping 192.168.237.128. And then Internet, ping 8.8.8.8. The two should work!

  Continue with steps [5-7].

• Disable the clichés for individual virtual machines?

  Hi all

  Is it possible to disable support for snapshot for individual virtual machines, perhaps via a parameter for it?  Or is the closest answer you to put all its virtual disks in independent mode?  Try to see how to better meet the requirements that certain suppliers impose that the VM/device does not catch instant and thought that the best solution is to disable the feature for the specific VM (s) only.  Thank you!

  You can watch the snapshot.maxSnapshots configuration setting. See KB 1031280 for more information.

• 'Disable the alarm action' for a virtual machine

  Hello

  I want to disable all actions for a virtual machine alarm, while I have to disable FT to clone a virtual machine. My script are ready for cloning but I have a solution to disable the actions of alarm for a virtual machine via PowerCLI to can´t. Someone knows a solution for PowerCLI 5.1R1?

  Thank you

  Michael

  -Entity parameter requires an inventory of PowerCLI as value object and does not have the names. You can try it like this:

  Get-AlarmActionState-entity (Get-VM-name VMTEST1) - Recurse: $false

• Start the virtual machine and wait for WF, does not connect to the computer virtual for Vds (Windows 2008 R2)

  Hello

  See a strange problem with only a Windows 2008 R2 model. When you use the built-in function "Start VM and wait" workflow to start a virtual machine (after conversion from a template either manually, or through workflow) NIC of the virtual machine (I tried VMXNET3 and e1000 times) does not connect to the problem. Vds can be replicated in a different VCenter, so spreading the vds. I also created several models of Windows 2008 r2 and all have this problem.

  If the model is converted and started outside VRO, it gets an IP from and is connected to the VDS immediately

  Tried add/remove the NIC of the model

  Tried to move the comments on different hosts

  Tried to create a new template from scratch

  NOTE: Windows 2012 R2 doesn't have this problem in the same circles, the only constant is the Windows 2008 R2 being started by VRO.

  Anyone seen this before?

  I found this article and it fixed my problem VMware KB: registration or the deployment of a virtual computer model fails apparently a fix a problem in ESX 5.1, 5.5 (I used the option to get around and things are good)

• How to disable auto-start for the virtual machine at the start of merger?

  Hi all

  I use Fusion 2.0.4 to run different OSs and have 4 different virtual machines that are installed. But whenever I start the merger, regardless of the previous state when I stopped him, he starts a specific virtual machine. How to avoid this? I want to start just merge and then choose which machine to start.

  TIA.

  Hello

  Welcome to the VMware Forums!

  In the virtual machine library, there is a star in the list of your virtual machines that you can click and she acts as a toggle to start the virtual machine on the opening of Fusion.

  It is somewhat a weird UI design choice, don't know me either until someone reminded last week.

  --

  Wil

  _____________________________________________________

  Visit VMware developers at http://www.vi-toolkit.com wiki

• Students cannot "connect/disconnect the virtual machine's CD/DVD devices.

  I will start with this context (and apologies for the wall o ' text): I'm a newbie.  I took the course VMware local community college offers [VMware ESXI Server Enterprise (CIS197)], but I've not yet certified. And I don't have a real experience, except what I have taught myself so far.

  I recently accepted a position of learning associated with the College (think: glorified lab tech). I was tasked to work with stuff from VMware in the laboratory (among other things such as Cisco and Juniper equipment). There is no pass-down information like the previous left the position four months ago.

  We have a single host running ESXi 348481 4.1.0. "We have vCenter Server (5.5.0, 1312298), running on Windows Server (2008 R2, Enterprise Edition).  Access host and vCenter through two different IP, addresses using the vSphere client (either 5.5 or 4.1, using a single application - depends to know if I connect to the host or vCenter).

  At that time, the host is using local storage only (we have plans to change this, but it will take time).  The host is not a production on its own server, because it does not have a school systems.  He does, however, run a number of virtual machines in the lab, students use (Linux, Microsoft, Web design, etc.).  So, right now, I can't take it down.

  I was tasked to create a number of virtual machines that students can use to make the basic labs of Microsoft Windows 7.  So far, I have:
  -Created users, one per student, on the host.
  -Creating VMs, deploy one per student, I have a gold model vcenter.
  -Creation of roles to limit the access of students to just their VM attributed, which they access via client vSphere.
  -Created a Windows Server 2008 R2 domain controller that is also a DHCP server.
  -Created a virtual network, which is accessible only by the Windows 7 virtual machines and is not visible outside the vSphere environment (if I said this right - he does not see the Internet or school network).

  So far, it's all good.

  However, I need to be able to allow students the ability to edit the ISO file on which their VM points in order to complete some laboratories. I guess they would use the button "connect/disconnect the virtual machine's CD/DVD devices" on the taskbar (or console window). It does not work.
  I searched a lot and found that others have had the same problem.  However, all of the solutions I've tried so far have failed.  When they click 'Connect to ISO image on the data... store. "they get an error message means nothing to me,"an internal error has occurred in the vSphere Client. Details: Object Reference not set to an instance of an object. Contact VMware support if necessary.
  The role that I use for students has these settings:
  -Data store > Browse the data store
  -Virtual Machine > Configuration > change the settings of the device
  -Virtual Machine > Configuration > settings
  -A bouquet under the virtual machine > Configuration >
  -Configure CD media
  -Console interaction
  -Connection of the device
  -On
  -Power off
  -(and more, which I don't believe are important to the question)
  -State > create the snapshot
  -State > go back to the snapshot

  I tried "Virtual Machine > Configuration > add existing disk", "Virtual Machine > Configuration > add new disk" and "Virtual Machine > Configuration > add or remove an instrument" with no luck.

  Either by the way, the root account can do all these things, but no other account can - not even a game as an administrator account.

  I've seen mention I have apply the role in the data store.  It is perhaps part of the problem. I can't see the data store when I am connected to the host (wellll, I can, if I click on the host name, then on the Summary tab - but roles do not apply at this stage).  I see is 'Inventory' (which has virtual machines and Pools of resources), 'Rôles' and 'log files '.

  I can see the data store when logged in vCenter. Roles of students, however, are defined on the host computer. If I clone the role of users in vCenter and change this role cloned to have "permissions" that those who are on the host computer and then apply it to the data store, it still does not work.

  So, after all this (which I hope I've included all the necessary information), what can I do to allow the students to change ISO to which they are connected?

  Of course, if I left something, or if someone has a question, please ask.  I want to get this resolved as soon as I can.

  It turns out that I finally found the solution to the problem.

  What 'fixed', it is sufficient to vSphere Web Client to vCenter, which then allowed us to use Single Sign-On (SSO).  This, in turn, allowed us to define users and roles in vCenter (rather than having set them up directly on the host computer) which have then been applied to the VMS of students and also to the data store.

  Now, they can (de-) connect their ISOs at will.

  I find it interesting that vSphere Client (application) shows the users (and the things that they have access to), but it won't let you set of users.

• In opening the virtual machine: "could not find a peer valid to connect to" or "error of Transport (VMDB) - 32" / "-14" ""»

  Hello

  Since yesterday after a reboot of my host (DELL E6410, W7 SP1 64-bit, 8 GB RAM, 2x750GB SATA3 running WorkStation 9.0.2 Update Windows Update), I can't open my existing VM.

  I often get "can not find a valid peer to connect to" and sometime before: "Transport (VMDB) - 32 error: Pipe: reading is not'or'error of Transport (VMDB)"-14: fitting broke"»

  I worked for 2 years on this machine without a hitch, WS7 reclassification in WS9 without any problem.

  FYI: we have changed the domain 3 months ago, but it has never be a problem.

  I have google and search several Forum. So far, I tried to:

  -restart the service vmware-auth as an administrator

  -launch vmware.exe administrator

  stop/start the vmx86 service

  -uninstall / reboot / install Workstation.  3 times. First using uninstall from the Control Panel, then doing a / clean before installation and finally track down any file/reg entry.

  -HE asked if any group policy changes were made recently (like not allowing to run vmware.exe?)

  -Rename vmware.exe (logs I look similar to what is in this post: http://communities.vmware.com/thread/331099?start=0 & tstart = 0 ... but no luck)
  

  -excluded vmware.exe in my AV (Microsoft ForeFront). Unfortunately, in that I'm not allowed disabled...

  -Open the virtual machine using the drive == > does not work either.

  This isn't a file corrupted in a virtual machine (even backup - 7zipped - don't work on my laptop... but the launch on the other).

  Even a newly created WM (boneless), unbootable! :-(

  *, BUT to BE NOTE *: if a virtual machine is created as a shared virtual machine, I can start the application locally remotely! And this same VM, if started (via the.vmx) does not work using Workstation GUI!

  I have attached 2 newspapers. Work a (vmware.log remotely) and the inactive (vmware-vmx - 4072.log thru WS GUI).

  Of after what I saw (and what little I understand), it's as if the CPU is not detected?

  The two newspapers have this line:

  FeatureCompat: EVC masks:

  but the non-working goes - we with

  Module CPUID initialization failed.

  While working it display information on CPU (hostCPUID name / family / type... etc...)

  Any idea is welcome.

  I'll answer me to my problem!

  A lot of research to this knowledge.

  In summary: don't mess with the processor affinity... or keep it in mind!

  Response to distinguish:

  I installed 6 months ago a small utility named prio (search for "PRI prnwatch"), because it can save the priority of a given process. What I did notice, is that it also save the processor affinity ! What happened: I probably changed the affinity once for a VM running to give greater priority to a 7zip archive process to complete more quickly (setting HT no core to 7zip and one - or 2? - HT core to VM). Everything works until the next reboot, where the CPU detection during * start EVERY * VM has been somewhat "damaged" leading to the wrong log message: failed initialization Module CPUID.

  This is the reason of *my* question. Perhaps it might help someone else?

  TIPS:

  For advanced people who do not want to check the processor affinity of each process in the Task Manager, you can try this Windows Powershell command (remember to launch PowerShell as an administrator):

  Get-Process | Format-Table-PriorityClass name, ProcessorAffinity property

  ProcessorAffinity column gives the number of representation of the authorized core, 1-bit by heart.

  15 = 1111 is all possible core (for a logical processor 4). Mine is 1 CPU with 2 core HT <=>4.

  LSB is the core lowest. So if you allow only core0 and core3 (1001) on a process, the number of ProcessorAffinity will be 9...

  Post edited by: cbiero (LSB and MSB...)

• Unable to connect to the virtual machine via telnet

  Hi all

  The VM on Vcenter everything is perfect with the network connection. I can't do a ping of the virtual machine remotely but I can not connect via telnet.

  For the same reason? And even more, I have disabled the fiewalls of the virtual machine (Windows 2008 R2).

  The error that says: could not open connection to the host, on port 23: Connect failed

  Can you please let me know how to solve this problem?

  Since there is nothing blocking the traffic of the virtual machine in ESXi, you can begin troubleshooting in the guest OS. For example is running telnet server and configured to accept connections?

  André

• regarding the connection of the virtual machine to the external network

  Hi all

  I'm new to vmware and I have two virtual machines with windows operating system 7. How to connect to the external network?
  can I assign a NATed IP to them?

  If the need to talk about virtual computer internally, you can add all the VM in the same VSS(vswitch 1) at the same port group Network2 VLAN40. for virtual machines on that VLAN can communicate among themselves without problem and configure all virtual machines with IPs in VLAN40. no need for an another vs.

  For internet access, first check with your network administrator, if the VLAN has a routing or this VLAN has access to the DNS server that provide internet or the proxy server for internet access. He will confirm. or you can also check if this virtual machine are able to ping your DNS server or proxy servers. If its power of ping so it has access to this network. Configure the virtual machines that you configure a physical computer for internet access.

  If the VLAN has access to the internet, even that you configure the physical server with connection DNS and proxy for internet access only the configuraiton even here too in the virtual machine.

• Disable communication between the host and the virtual machine

  I have VM Server 2.0 and one of the virtual machines has the same name as the server and even if the virtual computer is connected to the host only network it generates the Windows error message: duplicate names exist on the network.

  is there a way to disable communication between the host and the virtual machines? I just need a virtual network that is isolated from my network complete and host also.

  Thank you.

  The GUI Server2 is not to choose the other unused vmnets.  Then edit your file VMX use a different vmnet of 0, 1 or 8.  (which are bridged, host-only and NAT)

  Thus, for example, if your VMX has a line that says:

  Ethernet0.VNET = "VMNet0.

  change to:

  Ethernet0.VNET = "VMNet2.

  (This assumes that you have not used the network Editor to fill the vmnet2 either).

• need to configure a connection wireless network with static IP address to make a panasonic wireless display of work on the virtual machine

  Hi, I'm new to macs and Fusion. I have a MacBook Pro 13 mid-2009, running 10.5.7 and Fusion 2.0.5, running Win XP Pro SP3 as the virtual machine (not in a bootcamp partition separate). I added a second network as a bridged network adapter (first one is set to NAT). I'm trying to connect my wireless panasonic (802 11b) to the virtual machine display, as I do on my old sony PC. Normally, I turn on the wireless on the PC, find the network wireless in Win XP and configure my SSID and necessary of static IP address and configure the NIC to search only ad-hoc connections (non-infrastructure). I also turn off the firewall so that it can work. There is a panasonic program runs on the PC (which I also installed on the virtual machine) makes it all happen once I have the connection. So the place that seems to be stuck, it's that I can't find a wireless to configure network adapter since--what the VM is a NA standard, so there is no place to specify the SSID, ad-hoc and disable the WEP key. Someone has ideas how to go beyond my current state?

  In addition, the panasonic only works at 800 x 600 for the display resolution, so it will automatically change the graphics settings. I guess that's not a problem on the VM, but thought I would ask in advance in case someone sees a problem with it.

  Thank you very much.

  Larry

  If the only way you can connect to the device is via WiFi, then you will need to provide your own WiFi USB network adapter to the virtual machine because Fusion presents only the network card Ethernet wired to the Virtual Machine, regardless of the host network adapter is the main map.

• Cisco has disabled my internet connection I don't have the guest password - I never asked to Cisco

  My main computer is a Windows XP, I also have Vista and a laptop with Windows 7, XP is slow, the vista access no internet at all unless I put in some password for comments, that I never went also, I didn't want Cisco and if I did it lacked experience in computer science and an accident.  Please help, friends try to help and I lost all my music files and now I can't Netflix Blockbuster or Rhapsody.  Help?

  Software Cisco Connect think that my internet connection is lost, but it's not. It won't take me any further than that.  I would just use the administration of "Advanced" page but I am trying to enter to disable the guest network and for some reason, Cisco made that only configurable from the Cisco Connect software.

  http://homecommunity.Cisco.com/T5/Cisco-connect/Cisco-connect-software-thinks-my-Internet-connect-is-lost/TD-p/374485

  http://homecommunity.Cisco.com/T5/wireless-routers/setting-NAT-to-disabled-breaks-Internet-connection/TD-p/251760

• 'Fail forward' for Ports on the virtual machine

  We have a customer who will be centralizing the unit with about 250 users at remote sites (4 Sites, 1000 Subscribers, they have currently a unit break at each site and want to centralize). Each site will have its own cluster of CM. I'm thinking about what I could do failure network SCOPE. Of course, each site will be fine IPT wise because they have their own cluster of CM, but VM will be declining. I think I watered but if there was a way to "transmit failure" or something on the VM ports on the PSTN to maintain the work of the virtual machine. (Of course carrier must support ISDB).

  Someone at - it works in this or thought about it?

  Andrew Dignan... If the carrier supports RDINS of course

  The connectivity of voice mail for Cisco CallManager chapter of the Cisco CallManager System Guide:

  "Inter-classes Interfaces A Cisco CallManager in a cluster can provide access to a voice mail system in another cluster, if the administrator provides the voicemail number on the trunk driver inter-classes. Voicemail systems can leave messages and sets the flags of message waiting for devices other clusters if clusters are connected by trunks QSIG. »

  This applies to any system of virtual machine. With the unit, you have of additional capacity to save ports across multiple clusters so to provide MWI without ICTS as QSIG.

  Hope this helps,

  Eric

• I've set up the virtual machine in win 7 Ultimate and put some data. Now when I try to connect it asks password and does not accept any password.

  Default password Machine virtual XP Mode

  I've set up the virtual machine in win 7 Ultimate and put some data. Now when I try to connect it asks password and does not accept any password. Please giveme the default password

  If you're talking about XP Mode the default password is XPMUser.  In general you can not use Windows without a password in Windows Virtual PC that you can with Virtual PC 2007 and before.  XPMUser is used only with the XP Mode virtual machine.  All other virtual machines requires a user created password.  If you have changed the password in XP Mode and forgotten, then you have to start over.

  Windows Virtual PC is based on virtual server rather than VPC and all virtual machines need a password.  If necessary, uninstall the integration features, start the virtual machine and create a password for the admin user.  Restart the virtual machine, and then reinstall the integration features.  You will not be able to access a virtual machine created by the user that has no password, while the integration features are installed.  Once you have everything right, that a virtual machine will not be asked a password if you are the admin user in Windows 7.

  @george1009,.

  Everything got?  :)