Disk SATA 6 identified as SCSI

Similar Questions

• How can I change the player assigned to the SSD for a SATA instead of the SCSI drive?

  Original title: SCSI instead of SATA

  I built a PC with Windows 7 Ultimate 64 bit.  My C: drive is a Samsung 840 Pro SSD.  The system never worked properly and I discovered that the SSD which is a SATA 3 drive in Device Manager is configured as a SCSI disk.  Someone knows how to change the driver assigned to the SSD for a SATA instead of the SCSI driver?

  Hello Uriel,

  Thank you for your response.

  SATA controllers will normally appear as "SCSI" controllers in windows. It's normal and nothing to worry about. Often the SATA controllers will also be able to run in IDE mode and then they present themselves as IDE controllers, but it is unlikely that they will be able to operate optimally, as the IDE interface is missing some features of SATA. So even if you do not have the ability to set the cache in the Device Manager, a SATA controller is running in mode SATA should work just fine.

  The IDE bus is managed by the controller SATA3, and if this control is set in the BIOS to "IDE" somehow it seems related to the operating system as a SCSI device.  By setting this entry in the BIOS to "RAID/IDE" IDE devices get properly detected.

  This can also occur if you change the BIOS settings for the SATA ports of 'IDE' to 'AHCI' after installing Windows 7.

  I hope this information helps.

  Thank you

• I can't install the second disk sata hard

  I have a problem when install the second disk sata hard
  I bought a new one 500 GB and I installed windows xp sp3
  and it works well I plugged in SATA 0 port
  When I want to install a second sata hard disk 320 on sata 1
  and it has an important data, windows will reboot, and do
  blue screen sometimes 'NTFS.sys"or"SCSIPORT.sys.
  and it is written "DRIVER_IRQL_NOT_LESS_OR_EQUAL".
  If someone help me what should I do or there is no FIX for this problem.

  in the BIOS I have regcognized both hard drivers:
  IDE pri master 500 GB
  PRI IDE slave 320
  Second master IDE-
  Second slave IDE-
  PORT SATA - 0
  SATA 1 - PORT

  I plugged the IDE 2 cd-rom

  ----------
  Specification of the device:
  Windows xp sp3
  card mother gigabyte 848P
  Intel ICH5
  Intel 8I848p775-g
  Celeron D Socket 775

  You said that the hard drives are sata but your bios recognizes them as IDE depending on your position. You might have to set your bios to operate in sata mode or enable AHCI of have recognized them as sata. Regarding the error you get, look in the system BIOS to boot from hard disk command menu. This is different from the command menu of usual starting where you choose each time you start a cd ROM or hard drive ect... The parameter that I refer to determine which hard drive of your computer starts on the first. Change to the primary master 500 GB disk > save your settings and restart your computer. Even if one is defined as main and the other slave is not serious. Some bios have the ability to choose what hard drive to boot from. In other words, it is adjustable to start first on the slave drive.

• How Windows XP Setup (F6) to use an instead of a floppy drive usb flash drive to find the drivers for a disk sata hard

  Hello

  How can I install Windows XP Setup (F6) use an instead of a floppy drive usb flash drive to find the drivers for a disk sata hard.

  Kind regards
  Imane

  Hi Mike,.

  You can not install it. This must be done using the floppy drive. This feature is available for Vista and Windows 7.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Installation of 4 disks SATA on Dimension 8400

  I currently have 2 SATA drives on my Dimension 8400 and I would install 2 additional drives.  Looks like I have 4 SATA connectors on my motherboard and BIOS support SATA 0,1,2,3, but seems to have some power for only 2 disks SATA connectors.

  Is there an easy way to add some additional power connectors so that I can add more than two disks?  In addition, it seems that I have to remove my floppy drive to make room... is that correct?

  Thank you

  Steve

  
  

• Qosmio G20: XP Installation disk & SATA USB

  Hello

  I have Toshiba Qosmio G20 and I have the following problem:
  When I try to install new windows using the SATA drivers via the floppy USB drive as a process of installing classic XP SATA drivers are needed 2 times:

  First time as usual, you will need to press F6 to specify drivers via the USB floppy drive, that this is no problem. The works of diskettes.

  Afterworlds it is the second time that when the same SATA drivers are required from diskette (drive A :). After the selection of the 1 install Windows XP blue screen 3 options, before the first reboot. The installation starts copying the files required for the instillation process and asks AGAIN COPY THE SATA DRIVERS for more usage of the system.

  On this stage the USB Floppy is see inaccessible computer cant that it has USB floppy A:.
  So I can't continue with installing XP because for the next reboot is no SATA driver and no hard drive is detected.

  I tried this several ways and several versions of XP Setup, but the same result.

  Please tell me how to fix the problem will be updated firmware available which can see the USB floppy plugged into this scene.

  Kind regards
  Konstantin

  Hello

  Did you install the RAID driver?
  Well, I put t know if it because of this problem, but as much as I know the Toshiba RAID driver must be added during the installation, when prompt to 'press F6 if you need to install a third-party RAID or SCSI driver.

  To do this, please download the Toshiba RAID driver from the web page of Toshiba driver download and extract the zip to a disk file. Connect the floppy drive to your computer before starting the installation.

  The Setup program continues until you are asked if you want to "S = specify additional device. Press' and specify the driver Toshiba Raid for XP or 2000 as required.
  Press 'Enter' to continue the installation.

  When you use Windows Setup to partition or format the HARD drive, the RAID driver is deleted in the process.

  Please tell me if you have resolved the problem.

  Best regards

• Envy 17: Controller driver of storage for disk SATA 4 to

  Hello

  I can't the initialization of a new 4 TB SATA (Seagate Barracuda 3.5 ") drive. I connect to my HP Envy 17 (Windows 7 64-bit) via a USB 3.0 drive hard dock for purposes of backup only. Initialized using GPT, but nevertheless he refuses to show the true volume of the new HARD drive and the system keeps recognizing him as a GB 1677,9 disk.

  I read a little about this issue online and guess that only the volume above 2.2 to is detected but that he couldn't find a solution anywhere and Seagate does not offer one or the other. Have tried to update the driver for this disk (Microsoft driver version 6.1.7600.16385; driver date 21/06/2006) but the system tells me that this driver is up to date.

  Thanks for all your tips and advice!

  KrisD

  Hello

  Check with the manufacturer of the external USB docking station and ensure that it takes care of 4 TB hard drives.

  Otherwise, open the window RUN (Admin) and try the following:

  DiskPart

  list disk

  Select disk x---> x is equal to the target disk

  clean

  output

  Now, unplug the USB and plug it in again.  You should get a prompt to format and initialize the GPT to choose HD and assign a drive letter and label.

• the upgrade of the disk sata hard to new ssd sata 3 disc 1

  I have Hp m9510 running windows 7 64 bit home edition.  The motherboard is ASUS IPIBL-LB (Benicia), my drive sata hard existing 1 running in raid mode.  I want to add a new SATA of SDS 3 as a new startup disc and leave the player sata 1 existing as a backup.  Insofar as the motherboard is built for sata 1, if I install a sata pci card 3 I will then be able to obtain the transfer of higher data rates of the new ssd without causing other problems?

  If your current configuration has a single disc, then your default would be AHCI.

  RAID stands for redundant array or inexpensive disks and requires two or more physical hard disks for the implementation.

  In this case the preferred configuration would also be AHCI. It's a SATA mode. (Advanced host configuration interface) His replacement is IDE (emulation) mode

• physical disk sata hard d: went in 'Computer', undeleteable cd rom drive d: shows in its place

  windows vista edition operating system home premium

  My d drive is a sata hd with a single partition. It has only the data (no installation of operating system or the program)
  in car disappeared in 'Computer', but it is detected by my bios, it shows as working properly in Device Manager and appears in... Disk Manager but not allocated.

  a CD-ROM cd ghost undeleteable drive shows in places like d:

  so far, I tried the following to resolve this situation:

  1A ran full virus/spyware scan, computer diagnosis, etc...

  2. remove all virtual disk software for example daemon tools, power iso etc...

  3. start in safe mode

  4 running msconfig and try different boot configurations

  5. physically change the sata connector on the motherboard of the drive is plugged

  6 unplug the drive from, then stop to connect player departure and back again

  7 tried to restore to the point before this happens

  None of them brought no success, if anyone has a solution for this, please report it. I would not lose the data on this drive!

  Hello

  The CD Phatom drive appears in Device Manager as well?

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  ----------------------------------------------------------------------

  If necessary:

  Make a Restore Point

  Start - type Regedit in the search box - search at the top of list - click on - RUN AS ADMIN

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  Look here and the other keys to CurrentControlSetX\Enum\IDE where X is a number.

  Right-click on the PHANTOM drive and EXPORT the key to name something you remember. Then
  Once again right click and delete it. Do the same for all people.

  Whether it's there or not go back to Device Manager - right click on the hard drive (D :) and UNINSTALL it.
  The reader should be located and re-installed when you restart after checking the GHOST.

  If the GHOST is still there, see if you can DELETE it now.

  If you can or not - RESTART.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Don't see disk sata hard in windows Explorer 7

  I have an abit fatal1ty fp in9 sli motherboard with 2 GB of ram.

  I have a drive hard western digital 2 TB green with win 7 ult 64 on that.

  I added internal a drive hard hitachi 2 TB sister sata as a hard drive.

  I see the hitachi in the bios and in Device Manager.

  Device Manager indicates that the drive is installed and in good health.

  I don't see the hitachi drive in windows Explorer.

  I can see an old drive hard ide and the boot drive, but not the new hitachi in Solution Explorer.

  I've added the fix Windows6. 1 kb977178-v2-x 64.msu which is hot fix 404474_intl_x64_zip.exe

  It's funny that I can see in the Device Manager but not explored, I tried new scanning devices and reboot several times.

  any ideas?

  I fixed it!

  in Explorer, right-click on my computer and select manage.

  in the computer management screen select mangae hard disks and create a partion on drive of choice and format her!

  Sometimes the simplest things are the most difficult to do!

  Maybe this will help someone else.

• Impossible to activate the hard disk SATA card mother Asrock G31M-GS

  I have a desktop with the motherboard Asrock G31M. This is IDE and SATA connections I was using an IDE hard drive, I want to now put to update to a SATA drive. I have a Western Digital WD 1600 and a Maxtor Diamondmax and I can't have one of them to work.  It seems that they get recognized in bios but does not start until I can load the windows OS.

  I spend on the computer, it starts at the BIOS and when it should start windows or ask for the installation disc, it goes back to the Asrock start page and freezes.

  The DVD player is detected, but which is connected to the decision-making of the IDE.

  Ideas please

  Hello

  To enable or disable SATA hard drive to the motherboard, please contact Asrock for assistance.

  Asrock Support: http://www.asrock.com/support/index.asp

  Hope the information is useful.

• Disk SATA of OptiPlex 9020 m and m2

  All data sheets I can find for the Optiplex USFF 9020 indicate that it can withstand a SATA m2. Which non of them tell me what edge connector and the length should be, and whether or not an impasse is required for the end.  I contacted the technical support, who sent me to the line of factory parts, but seemed to understand what I was looking for.  They kept directing me to parties for the addition of a 2.5 "SSD, not a SATA m2 card.  Also, the manual download users was a link from the U.S. site dead for weeks.  Can anyone help?

  Based on the research to the motherboard, I think I can use a 42mm card with a 'B' or 'B & M' edge connector.  But, again, nothing to confirm.

  Thank you.

  -Tim Reid

  Hi Tim,.

  Thanks for your question.

  I found some references that we've sold with the 9020 M m2.

  Dell support for reference numbers:

  331T 3 128 GB SSDR 3.65 MM, S3, SMSNG, PM851

  5612H SSDR, 256GB - SATA3, 2280, L9G Liteon

  PF19K 128GB SSDR 3.65 MM, S3, Toshiba, HG6

  I analyzed the part number for Dell PF19K, to form M2280 - Toshiba THNSNJ128G8NU from Toshiba HG6 part number factor, 3.65 mm. This is a real picture of it:

  

  Specs of Toshiba:

  http://Toshiba.SEMICON-storage.com/us/product/storage-products/client-SSD.html

  I found a pic of a similar m2 installed in a 9020M:

  

  Also, I tried the link to the owner's manual download and it works well on my side:

  http://www.Dell.com/support/home/us/en/19/product-support/product/OptiPlex-9020m-desktop/manuals

  I hope this helps you.

• I need the specifications for the replacement of hard disk, sata 2, sata 3, 3gbs or 6gbs hybryd or SDS.

  Sony vaio VPCEE42FX came with a 500 GB hard drive, can someone tell me the specifications of tranfer rate as can the Board read 6 GB or 3 GB per second, also I want to change to a 1 TB hybrid drive which is the rate of transfer of 6 GB. None where he appears with these specs sata 2 or sata 3, etc. I even used the sony logme service and they told me that they do not know. Some one out he must know it please help, thank you

  Pitman,

  According to the chipset of this unit, it supports SATA 2 (300 MB/s).

• XPS8500 mSATA iii, HARD drive disk SATA port?

  I have a XPS8500 Office with 2 SATA iii HARD drive currently as the only player to. I bought a 1 to Samsun Evo 850 to replace the HARD drive (the HARD drive has only about 600 GB used, so it should migrate completely without problem). Ports SATA 4 deep 1 SATA ii and SATA 0 and mSATA ports are the only SATA iii ports, I would move the existing 2 TB HDD in a location empty in the cage with the SSD drive in the location of the SATA 0 port. Ideally I would drive the HARD drive using the port mSATA to keep capacity SATA iii. Is there an adapter that will allow you to it? In other words: an adapter to change the architecture of the port mSATA connector to allow a normal SATA cable connect the port for a SATA drive.

  There are adapters to convert a port mSATA on the motherboard in a standard SATA 3 port to a HARD drive. If you google around you can find them, for example this one.

  Remember that I do not specifically recommend (or not) this map or this provider. So shop around to find what fits your needs and your budget.

  Also, I have no idea how that these adapters are working (or not).

• New disk SATA hard for HP Pavilion Elite m9065.uk, a desktop PC

  I am wanting to buy a new hard drive for my HP Pavilion Elite m9065.uk, a desktop PC. Here are its specs:

  http://support.HP.com/us-en/document/c01242071

  Now, the material is not my specialty. I know that I need a SATA drive, but I don't know that one to buy? I will be limited to the capacity of HDD can I install it? I would ideally like to 1 TB.

  I guess I can't install a player?

  Thanks a lot for any advice.

  Hello

  Your computer is fairly new, you should be ok, installation of a 1 TB drive.  Older computers may have problems of card motherboard/bios with bigger hard drives.  You can also install a SATA2 drive, but if your motherboard doesn't support SATA drive will just default to this speed (SATA2 is backward compatible).  The player below is to consider.

  http://www.Amazon.co.UK/Seagate-Barracuda-7200-12-drive-cache/DP/B0024FAN24/ref=sr_1_5?ie=UTF8&QID=1287523497&SR=8-5

  Hope this helps,

  DP - K