DMM 5.2.2 - 5.2.3 MCS 7835-H2

Similar Questions

• DMM 5.3 on MCS - 7835 H 3 and DMM-FA-C210-K9 failover

  Hello

  We are working with a customer who wants to add redundancy to their existing environment of DMM. We initially deployed their solution on a Server 3 - DMS MCS - 7835H and finally improved to 5.3. Now, they want to add the failover and the DMM-FA-C210-K9 with DMM-FASW-52-K9 bought another partner. After sitting idle for several months they have committed to us to help find a solution.

  I see 5.4 is able to run on a virtual machine. I have the following questions.

  Can I upgrade the DMS MCS7835H3 v.5.4? Based on the upgrade document 5.4, it seems to corroborate.

  • If we can improve the MCS7835HE-DMS 5.4 failover will work with the DMM-FA-C210-K9 Server?

  Since they already have the DMM-FA-C210-K9 server, can it be used as a host VMware to run 5.4 practically?

  • If so, failover will work with the MCS - 7835H 5.4 3 - DMS Server?

  Ray,

  The answer to both your questions is no.  None of these options is supported.

  If you use a virtual host primary servers and failover must be virtual.  You cannot mix types here.

  Also the MCS 7835 is not supported in a failover deployment.  Only the DMM-SVR-C210-K9 as backend is supported by 5.4 tipping guide. http://www.cisco.com/en/US/docs/video/digital_media_systems/5_x/5_4/dms/failover_guide/dmsfailover.pdf .  However, the DMM FA C210 K9 can be used as the fallback server.

  Hope this helps

  John

• MCS-7835-H3 headed Amber hard drive alarm

  Hello everyone,

  I have a server MCS-7835-H3, DMS 5.2.1. The server has 4 hard drive (300 GB each disc). I noticed that one disc is alarmed, the led is amber.

  I was looking for literature on this topic, but I can't find anything.

  I was watching the b.b.q and IAA interface for some information on the status of the drives and nothing... in the log files or...

  Can anyone helpme to know what is happening?

  So thanks a lot!

  

  Error light = replace. These things are pretty accurate, so if you have an error on the disk it will probably fail at some point if it isn't already.

  Aaron

• DMM 5.2.2 7835 H 2 DMM 5.4 VM migration

  Hi all

  We are running DDM 5.2.2 on a MCS 7835 H 2 Server and use only the DMP 4400.  We are looking to migrate to DMM 5.4 as using our software upgrade contract.  I went through the options options/upgrade of migration and to understand the process of having to go through the 5.2.2 > 5.2.3 > 5.3 > 5.4 > 5.4.1.

  But I don't have access to a a MCS 7835 H 3 or C210 server, but I have access to a C220M3.  Is there a migration route to take me to 5.2.2 for 5.4.1 running on our UCS B series taking place in VMWare 5.0?

  I saw the migration document that references the migration of 7835H 2 for the C210 to http://www.cisco.com/en/US/docs/video/digital_media_systems/hw/platform/migration/dmm-mcs-ucs.html

  But, as mentioned above do not have access to a C210 to undertake this.  Is there a way to take 5.2.2 configuration and this directly to import it into a new installation of 5.4 (I guess not).  can I use the C220 instead of the C210?  If possible can I run through the migration, do upgrades to get to DMM 5.4.1 install a double DMM 5.4.1 in VMware and backup the C220 and restore the installation of VMware?

  Thanks for any help.

  Concerning

  David

  Happy new year

  Hi David,

  You can see a similar description in the following thread:

  https://supportforums.Cisco.com/thread/2190258

  The answer is no, it is not a migration path official at this point if you have not already migrated it to C210 before, unfortunately. You need to trigger this to your Cisco team account in order to get help with this.

  Best regards and happy new year,

  Marco

• Possible to install UCCE on the same server as CallManager MCS

  Hello

  Trying to set up improved 4.5 on an MCS 7835 UCCE. Now, if I want to install CallManager 5.1 in this environment, can I put the same box of MCS? Or do I have to buy an another MCS?

  Thanks in advance.

  Juan, I think that you misread his post.

  "If I changed CallManager express to 4.2 then it would be possible to run on the same server MCS?

  I don't think that he meant "CallManager express."

  The solution, lpezi, is to read the compatibility matrix where all your questions are answered.

  http://www.Cisco.com/univercd/CC/TD/doc/product/voice/sw_ap_to/crscomtx.PDF

  Kind regards

  Geoff

• TP Installation

  Hello

  I am new to telepresence, and I got a job to establish the environment of Cisco WebEx One Touch Meetinig Teleprence. have got facilities such as below:

  MCS-7835-I3-ECS1, CTS 3000 codec; the documentation seems there is Server/service as Community trade marks, CT-manager and CUCM.  My question is: what equipment should perform such services, or need to connect remote CUCM?

  It would be better if can get more information

  I would recommend starting with the 'prerequisites' here:

  http://www.Cisco.com/en/us/docs/Telepresence/cts_admin/webex_solutions/guide/cts_webex_pref.html#wp1010482

  The WebEx OneTouch feature requires a CTMS (MultiPoint Switch), CTS-Manager & CUCM to implement. You can use the Commerical Express option to combine on a single MCS Server (there are some drawbacks with the number of users, etc.), see here for more details on this:

  http://www.Cisco.com/en/us/partner/docs/Telepresence/cts_admin/Commercial_Infrastructure_Solution/guide/bundle_solutions_info.html

• Autonomous CVP w Reporting. VB Admin out of Service

  CVP 4.1

  Autonomous with reporting model:

  1 GW 3845

  1 MCS 7845 call + VxML Server

  1 MCS 7845 Reporting Server

  1 MCS 7835 OPerations Console

  1 studio of MCS 7835

  I registered online PAK codes for the

  -Server-Sw and applied the ICA on the server to call

  -CVP 20 VxML Ports on the VxML Server 4.x

  -Reporting Prem lic on the report server

  using the operations Console

  Also, added the GW and transferred the CVPSelfService.tcl, the CVPSelfServiceBootStrap.vxml and the CriticalError.wav to the same using the Console.

  Call the server, server VxML and Reporting Server are UP on the Console.

  Have restarted the combo CallServer + Vxml Server, but the speech browser shows out of Service and tries to contact the GK.

  But it is independent, there is no GA, why VB is trying to get a GK?

  I didn't go any single on the VB Admin command, as the configuration guide has not said to me to do.

  First Question:

  1. While installation was SVC Call Server I supposed to select H.323 as Autostart CVP VB services at startup, no. Sytem restart on error display & CVP VB window on startup, or NOT?

  Because I did, but then I added call server in the Console of the operation - I did not any service at all.

  2. If the answer to the above question is that Yes, I had to select H.323 Services/Start VB window etc. during the installation options. Then what don't get me, why the VB is out of service and it is looking for a GA?

  Kindly help.

  No voice browser is required.

  Kind regards

  Geoff

• Update of telepresence

  Dear Sirs,

  our clients have three CTS-3000, CUCM Cluster, Manager of CTS, CTMS.
  CTS-3000 - Firmware version is 1.4.3.
  CUCM - Version is 5.1.3.2000 - 3, the material is MCS-7825-H3.
  CTS Manager - Version is 1.3.1.0 (460), the material is MCS-7835-H2.
  CTMS - Version 1.1.0.0 (254), material is MCS-7845-H2.

  Customer has a Cisco warranty. The customer now wants
  upgrade of the solution up to 1.6 version and CUCM up to version 7.1.

  1. the following (after 1.4.3) versions of firmware are available for the CTS-3000:
  a. 1.4.7 (2229);
  b. 1.5.1 (2082).
  c. 1.5.10 (3648);
  d. 1.5.11 (3659);
  e. 1.5.12 (3701);
  f. 1.5.13 (3717);
  g. 1.5.3 (2115);
  h. 1.6.0 (3954);
  i. 1.6.2 (4023);
  j. 1.6.3 (4042).
  Should install us all versions of firmware under the instruction of one or
  There is a recommended update sequence?

  2. the following versions of software are available for the CTS Manager:
  a. 1.3.2 (466);
  b. 1.4.0 (279);
  c. 1.5.1 (420);
  d. 1.5.2 (423);
  e. 1.6.0 (220);
  f. 1.6.2 (64);
  g. 1.6.3 (113).
  Should install us all versions of the software under the order by one or
  There is a recommended update sequence?

  3. the following versions of software are available for Community trade marks:
  a. 1.1.1 (30);
  b. 1.1.2(6);
  c. 1.5.0 (222);
  d. 1.5.1 (2);
  e. 1.5.2 (21);
  f. 1.5.3.12;
  g. 1.5.4(4);
  h. 1.5.5(1);
  i. 1.5.6(1);
  j. 1.6.0 (108);
  k. 1.6.1(2);
  l. 1.6.2(3);
  Mr. 1.6.3(2).
  Should install us all versions of the software under the order by one or
  There is a recommended update sequence?

  4. what sequence of update should be used?
  Firstly the CUCM, then CTM, Community trade marks and the CTS-3000 to last.
  Or there are more good sequence?

  Thanks in advance.

  1. you can go directly to the latest version 1.6.3

  2. If you want to go 1.6.X you must update in 1.4 first and then do a direct to 1.6.3 upgrade once you run 1.4.0

  http://www.Cisco.com/en/us/partner/docs/Telepresence/cts_manager/1_6/Admin/ctm_instalCTS_M.html#wp1080226

  3.

  The upgrade to version 1.6.0 CTMS

  When the upgrade to CTMS version 1.6.0 you run CTMS Release 1.1.2 or later. If you are running a version prior to CTMS Release 1.1.2 update to version 1.1.2 CTMS before the upgrade to CTMS version 1.6.0.

  http://www.Cisco.com/en/us/partner/docs/Telepresence/multipoint_switch/1_6/release/notes/CTMS_1_6_RNs.html#wp96444

  4. I first put the CTM CUCM, then CTM and last endpoints

  HTH

• ASIX MCS 7832 pilot to 200 for USB 2.0 to Ethernet?

  Digitus made a USB to Ethernet Dongle (DN-10050) using the 6 MCS 7832 chip.

  This dongle would be directly usable in 200?

  This is true, the driver 6 MCS 7832 must be pre-installed by Toshiba or be already present in ICS.

  If not, is there another driver present to 200 (with the flavor of the ICS) makes "USB 2.0 to Ethernet?

  Thank you in advance.

  Hello

  I read in some Forums Android that Digitus Ethernet USB adapter is not supported by Android.

  > To make this true, 6 MCS 7832 driver should be pre-installed by Toshiba or already present in ICS.

  Don t think that there is no present in Ice Cream Sandwitch and according to the page Asix, the Android driver for this chip. Just the driver Windows, Linux, and Mac OS are available.
  http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=108;74;109&PLI = 74

• Delay time 4070 PXI DMM

  Hello

  I use a PXI-4070 DMM and DotNet "SoftwareTriggeredMultipointAcquisition" example

  I want to trigger the DMM4070 with the AuxTrig entry to the front of the instrument.

  This works very well, but how can I change the time out the of triigger?

  It is now on 2000msec. I want to 10000msec.

  When I us the example and do not trigger in the 2000msec I get error message saying:

  ModularInstruments.NIDmm: The operation did not complete in time maximum allowed. Timeout: 2000mS.
  Error code:-1074126845

  Thanks in advance

  Wissam

  Hello JaredRo

  I can set the time-out period now.

  Problem solved. Thank you Manny

  With greetings

  Wissam

• Measure the resistance with PXI DMM 4072 on different frequencies

  Hi all

  I tried to get on board various and unable to find solutions for that. I'm trying to measure resistance using NI PXI-4072 on frequencey 1 kHz, but not luck. When I try to use Agilent LCR meter I see the correct value of the resistance.

  I've seen a few posts on this but don't have no satisfactory solutions.

  http://forums.NI.com/T5/Digital-Multimeters-DMMs-and/LCRmeter-test-frequency-for-resistance-measurem...

  In above post, someone said that I can use 4072 DMM OR digitizer, does not have a lot.

  Can someone please provide the right path for me to solve this problem.

  Thank you

  Hello Puneet_K,

  I checked the data sheet and the method of measurement described in the specifications of the NI 4070/4072 http://www.ni.com/pdf/manuals/371304g.pdf; indicates that the ability is measured using an alternating signal and select the test frequency range, for example 3 kHz, 1kH or 91 Hz. The resistance is simply measured using a DC signal, and it is often sufficient to measure the internal resistance of a battery. If you need a more flexible control for the measurement, you probably get a card like the function generator and then set a multimeter to measure the voltage and another DMM to measure the current and calculate the impedance of these values.

  I hope this helps!

  Kind regards

  -Natalia

• Specification OR ELVIS II + DMM

  Hello

  Recently, I use NI ELVIS II + for the characterization of the sensor due to the measurement of the resistance to 100Mohm.

  However, I found the spec said 100Mohm measurement can be done by using max test 5V voltage source and current source internal 500 nA? Using Ohm's law, 10Mohm has proved to be the maximum extent?

  

  Kind regards

  Sin Chong Yung

  Hello

  DMM NI ELVIS II has a permanent entry of 11 MOhm resistance. For the measurement of the resistance, the device under test (DUT) is assumed to be in parallel with this 11 MOhm. The ASE resistance is calculated from this nonlinear relationship by measuring the test whereas calibrated current excitation voltage and parallel resistance.

  For example, a 10 MOhm DUT measured in the interval of MOhm 100 with a current excitation nA 500 would show all (11 M: 10 M) * nA 500 ~ = 2.6 V.

  With a 100 MOhm DUT, the test voltage would be of about (11 M: 100 M) * nA 500 ~ = 4.95 V... right against the limit of 5 V.

  Enjoying a beautiful, the test voltage is (11 M) * nA 500 ~ = 5.5 V that is larger that the 5 V limit and is detectable in the 'OPEN' in the software.

  NI ELVIS II DMM design was obtained from an other DMM with the input resistance is selectable (11 MOhm or > 10 GOhm). In this case, the excitement of nA 500 could be used in conjunction with the 10 GOhm input impedance to give 10 MOhm resistance measuring range. Since the resistance of the DMM NI ELVIS II entry is fixed, there is a separate offer 10 MOhm.

  I hope this is useful,

  Charles Y.

  National Instruments

• DMM

  Hello

  H NIDMM 3.0.6 installation but I couldn't find examples in there.

  I have woul dsincerely grateful if you can help me to find the examples for the DMM OR C.

  Thank you

  -Sulva

  Hello Sulva,

  Examples in ANSI C are not installed by default. You will have to activate their installation by going to add/remove programs, and clicking on National Instruments software. In the list in the pop-up menu choose NOR DMM 3.0.6 and press the button Edit in the following pop-up window, navigate to Modular Instruments > NOR-DMM 3.0.6> > Microsoft Visual C++ Support and right click and select 'install this feature to local drive.

  Once this is done installing you should be able to find examples by going to Start > all programs > National Instruments > NOR-DMM > examples

• Export the extent of DMM trigger

  Hello

  I would like to export the trigger Signal, which I receive on channel 0 of the scope to a DMM in a PXI system.

  So far, the scope is what I want it to do (Acquisition of 1 Record with a length of 550000 at a sampling frequency of 50 kHz with a 1 s pre-trigger).

  I would need to know the value of the DMM measurement in the scope of triggerevent. For this, I have inserted the signal.vi 'export' to the scope and set it to trigger reference and as terminal output that I chose 'the trigger PXI 0/RTSI0 line. The digital multimeter, I put the command Source for "TTL0", which should correspond to the line on which I'am export the Signal of the scope.

  But it does not work. The DMM sends the value as soon as I start the vi (she does not wait for the Triggerevent). If I choose 'none' as a signal to export in the scope, the DMM waits until he goes into a timeout. Do I have to configure something differently, or do I have to use the vi TCIk?

  Thanks for your contributions!

  Pietro

  
  

• What version of NOR-DMM is later?

  It shows on the search page for the NOR-DMM driver, NI - DMM 15.0 was released in August 2015.  15.1 received July 2015.  See the problem?  15.1 was apparently released prior to 15.0.

  Which is the most recent?

  Hi CurtisHx,

  Long story short, NOR-DMM 15.1 is the latest driver.  The reason for this is that it supports a few things 15.0 have such as:

  1. support to debug a NOR-DMM device in use by another application, supervision or control of the aircraft in the NOR-DMM Soft Front Panel.

  2-OR-DMM 15.1 and later supports the following real-time operating environments:

  a. Module time LabVIEW Real-time

  b. LabWindows/CVI real-time Module

  However, NEITHER-DMM 15.0 only adds support for LabVIEW 2015.

  In regards to release dates, it was more to do with the process of downloading on the web.  Sorry for the confusion!