Do I need an additional access point to use my iPod touch for audio books? It's using iOS 9.3

Similar Questions

• Upgrade license 4402 for additional access Points

  You can apply the L-LIC-WPLUS-25 to a 4402 to enable multiple access points? Or are the 4402 models all locked in their designated access point license?

  Thank you

  -Con

  Hi Con,

  Unfortunately not :(

  The number of support of the AP is "hardcoded" on the WLC model and is not expandable up to 5500 series.

  See you soon!

  Rob

• LAPN300 - the best configuration for 3 access points, while using the same SSID

  Hi all

  What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?

  I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.

  What do you think? What is the best way or do, or could suggest you something else?

  As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network?  Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature?  Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?

  I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.

  Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.

  Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.

• Unable to find the access point or use any device to all wireless to connect to my BEFSR41 v4.0

  Hi well the problem seems to be that whenever I try to use any type of device and try to connect using a wireless connection to my router, I can't find an access point or no signal at all of it, but when you use a wired connection, it works perfectly. For example, I'm trying to connect my Wii to the internet via a wireless connection, but I can't find any access point so that it can connect to. So I went to my router configuration and I didn't know what to do to allow a shown access point or wireless to all activity. Theres no wireless tab or whatever it is to install, so I didn't allow remote administration, but still I could not find an access point. I don't know if im just made bad or I need an update of the firmware (mine is currently 1.04.02) or what else. If the help would be nice

  BEFSR41 isn't a wireless router... It is wired.

• Should switch BEFSR81 - wireless access point I use?

  Hello

  I have a cable modem connected to a Linksys BEFSR81 switch under the stairs. It distributes points of LAN cable to every room of the House - it worked perfectly for years and continues to do so.

  I need to add wireless (for iPhones etc.). I connected a Netgear WPNT834 DSL wireless router in a LAN points. It broadcasts a SSID I can 'see' on my iPhone - I can connect to it, but cannot access the Internet.

  Looking good, I found the two devices by default the IP 192.168.1.1, so I changed the IP address on the BEFSR81 on 192.168.1.2. Still no access to the Internet via the wireless Netgear.

  I guess that there is a relationship between the two devices share the bandwidth, but I'm at a loss to know where to start.

  These two devices are not compatible, or is there a way to their cascade work together? Or, is it a point of access wireless (linksys or cheaper universal device) that I can plug into one of the LAN edge to add a wireless network to the existing local network?

  Thanks for your help.

  Hi Mikey'it,

  The Netgear and Linksys are compatible when you want to set up this way. You must configure the Netgear router to a wireless switch. As disable the "router" function and DHCP. You must ask the Netgear support how to do it. Because the Linksys router works perfectly, you need to change anything.

  

• Routers using broadband as simple access points?

  I need a simple Access Point and the WAP610N seems sufficient. However, I would like to get capacity simultaneous dula-band, and it seems that I have to go to something like the WRT400N to get the. However, the WRT400N has a broadband connection. I can just 'not use' broadband capacity, making the WRT400B to be, in essence, a simple access point?

  See here.

• Mobile data does not and the name of the Access Point settings are not available

  I don't have a mobile data, not even the small up and down arrows or letters beside the sims signal bars appear.

  I tried all the troubleshooting settings and different type of network, the airplane mode is off, mobile data are no limit, no power save modes are on. Phone is dual sim so I tried on the two sims and tried to disable the other sim and changing the sim slots, both sims are loaded with a credit of data that works in other android devices. WiFi works fine. Factory reset does not help.

  There is that one thing that I can't not try troubleshooting. When I select settings > more > mobile networks > access point names, it says

  "Access Point name settings are not available for this user.

  Maybe if I could put APN I could get mobile data. How can I do or how I can try to get mobile data to work?

  Phone's Xperia M4 Aqua E2363 with build 26.1.B.2.102 thanks if you can help

  This text is a bit misleading, which is something that I have forwarded internally as your comments.

  If you have no NPP stored the phone displays the text "the name of the Access Point settings are not available for this user" even if you use the owner account and have access to the settings.

  Try to download the automatic settings from settings-> more-> Internet settings and see if that helps.

• Ordered the wrong access point!

  I thought that I had ordered a 1130ag but looks like I ordered a 1131ag LWWAP.

  Please could someone tell me what the difference between a 1130 and 1131. I understand I can load the IOS on the light AP software using a tftp server, but I do not know which exit to load on this subject. 12.3JX, 12.3JA, 12.3JEA, 12.3JEB! can anyone help please? either by the way, I am in the United Kingdom, do not know if this affects image to install. Thank you.

  Hi Paul,.

  This happens all the time, so it shouldn't be a problem :) I'm guessing that you have received this AP - AIR - LAP1131AG - x - K9 LWAPP. When you really wanted this AP - AIR-AP1131G-x-K9 Cisco IOS software. Look at the comparison;

  http://www.Cisco.com/en/us/products/ps6087/products_data_sheet0900aecd801b901c.html

  That being said, you should be good to go with 12.3 (11) JA1.

  To access Cisco Aironet to Cisco IOS version 12.3 Points (11) JA1

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b11jar1n.html

  Cisco IOS version 12.3 (11) JA1 supports 32 MB independent platforms. 16 MB platforms and platforms supported by Cisco IOS version 12.3 (8) JA and earlier versions (350, 1100, 1130, 1200 and 1230 access points and access point/bridge 1300 series) are supported by Cisco IOS version 12.3 (8) JEA1.

  Do not install a "JX" (it is a software image support to upgrade and recovery Cisco Lightweight Access Point Protocol (LWAPP));

  These release notes describe features, improvements, and caveats for Cisco IOS release 12.3 (11) JX1.

  Note: This version must be loaded on points of access to the plant or by using the lightweight stand-alone mode upgrade tool. Your access point may become unusable if you install this software without using the upgrade tool.

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b311jx1.html

  Returning to standalone Access Point

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  I hope this helps!

  Rob

• Windows 7 PCs are not connected to the closest access point

  Windows 7 PCs are not connected to the nearest access point.  Any ideas?

  For example:

  We have AP 1 and 2 of the AP for exaple.  They have the same SSID.  AP 2 is further with a bad signal.  AP 1 is closest with an excellent signal.  Why my laptop does not connect to the AP 1?

  You MUST use the same SSID.  I think that you misread my post.

  And Yes, a channel problem is that what I have proposed.  You can try to configure access points using the 3 discrete channels (1, 6 and 11) to minimize any overlapping units to the same channel coverage.
  At least this is the traditional way, we do it, although the automatic selection increases common and 11n 40 Mhz channels (if defined in this way) are also in.

• I updated my ipod touch on January 26, 2016 and now I can't access my music or playlists. Just an image when I select the music app.

  Now, I can't access my music lists or playlists.

  I just get a picture of a girl with APPLE MUSIC written on the screen and my music plays automatically in alphabetical order.

  I have the same problem as Samantha. Impossible to access my music on my iPod Touch 6Gen after I have updated to OS 9.2.1

  When I select my music App all I get is a picture of a dark-haired girl in a black leather jacket, helmet. In the middle of the screen is written in white APPLE MUSIC.  I can't get rid of this screen.  Before that, my iPod Touch 6 G worked perfectly and showed all my music. Other than this problem, my iPod Touch works well after the updated operating system up-to-date. Help?

• I use XP pro 64, but I have an access point in need of true 32-bit data. Is it possible to do?

  I need output Excel spreadsheets .txt files because I have an access point that is able to accept only clean text files (not Word files, etc.).  When I do that on my system, the ap gives me an error that he sees the nonprinting characters.  I look at the file .txt with a hex editor, and I see that it is completed by the hex 00 between each character.  I know I can solve this problem by loading a 32 bit OS, but I can do on the latest data from get system the way I need it?

  Hello Al C82,.

  Thanks for visiting the site of the community of Microsoft Windows XP. The question you have posted is related to Excel and would be better suited to the community of Office Discussion groups. Please visit the link below to find a community that will support what ask you
  http://www.Microsoft.com/Office/Community/en-us/flyoutoverview.mspx

  Steven
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• I need assistance with my WAP54G access point!

  I tried to connect my nintendo dsi to the internet using the WEP encryption, so I went to my router configuration page, then he wasn't no matter what tab wireless or settings on the page... my dsi SYSTEM can go to the internet via the setting of WPA, but my games, which is supported with WEP setting cant. so, I really need someone's help now! I don't want to miss the online features of my games... also, I asked my father if he can help me then he says he can only if I find the CD or download WAP54G ver 3.1 somewhere.

  Thanks in advance...

  If your Access Point is connected to a wired router, so you don't have to change the settings of your router, you just need to enable wireless security and change the SSID of your Access Point, and it should be good to go... Also make sure that your Access Point is in the subnet of your router...

  If the IP address of the router is 192.168.1.1, then the Access Point on your address IP should be 192.168.1.245...

• Beginner needs help with Aironet 1131 G Wireless Access Point

  I have a new Cisco Aironet 1131 G wireless access point.  It takes an IP address and I can ping this address.  However, I can't access it via the graphical user interface based on the web or the CLI.  I preformed reset.  Any suggestions would be greatly appreciated.

  Thank you.

  Hello

  I can't access that means? you are not able to go to the CONFIG T of the CLI prompt? and if you are in the same subnet as the AP, are you not able to open to the top of the GUI? If you are not able to then, with the command 'show version' on the AP CLI and see if your image is "RCVKW8". If so you will need to convert the same IOS using the method below.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap22-trouble.html#wp1038660

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• Had to reinstall my computer Dell laptop n5030 and now I need to recover dockport and access point for webcam

  Hi you all. I have a computer with webcam dell laptop n5030 integrated. It crashed and I had reinstalled it. now

  the dockport disappeared, so is the access point for the webcam. How to retrieve both. can anyone help?
  Original title: rice J J from Mobile

  Hello

  Find the latest drivers and software for your Dell model and the operating system on the link drivers Dell.

  Then download and install them.

  http://www.Dell.com/support/drivers/us/en/04/DriversHome/NeedProductSelection

  See you soon.

• WRT310Nv2 I need to add a point of access that are compatible?

  I have a very weak signal, where my PC is against my wireless router, so I want to add as a Repeater access point, but I can't find a compatible list. I ran into a problem, try to add a Repeater or AP to a previous linksys wireless router and it would talk only with the exact same router, so I want to check before you buy something.

  Thank you!

  You can go with WRE54G Range Expander or WAP200E, repeating the signal router WRT310N Wireless Access Point.