do not connect not lightning cable

Similar Questions

• Linksys Router WRT160N - Wireless does not connect to the cable modem

  I installed the Linksys WRT160n router to replace an existing G router. When installed the new wireless router works, but the router does not receive a connection (IP address - look under status) of the cable modem (so no internet). When I reconnect the old router and then connect the new router, I get any internet connection through two routers (so the old dishes router the IP address that accepts the new router).

  I have configured the router N new for

  "Automatic configuration - DHCP", no need for connection, IP address dynamic, etc (as required by ISP - Timewarner)

  I tried to renewal and release IP address by the router N when it is connected directly to the main switch (the switch to connect to the cable modem). In so doing, shouldn't that assign a new IP address to the router?

  I am allowed 3 IPs from the cable company (because of the switch) and I use all three with three different internet IP cameras to each address for home security system.

  Any suggestions on why the router is not connecting to the internet? Do I need to reboot physically everything on the network, including the cable modem?

  If I understand your post, you said that your ISP gives you 3 Internet IP addresses and you have 3 cameras that use one of these Internet IP addresses.  If this is correct, then that leaves no IP Internet address for your WRT160N use - so that would explain why your WRT160N cannot get an Internet connection.

  If I misread your post, and you have an Internet IP address available for the WRT160N, you might have a problem with your modem and two WRT160N tries to use the same 192.168.1.x subnet.  To check this, follow these steps:

  (1) Please indicate addresses that use your cameras (IE before you take the test below).  If the addresses do not begin with 192.168, then erase the last half of each address.

  (2) Please indicate your ISP

  (3) Please indicate the make and exact model of your modem (not the WRT160N) number.

  (4) Please do the following test:

  Put your entire network.  Disconnect the switch (including cameras) to the modem.  Using an ethernet cable, connect your modem directly to your computer.  (Do not use the WRT160N for this test).  Turn on the modem and the computer.  Make sure you have an active Internet connection, then go ahead with what follows: (even if your Internet connection does not work, include this and move forward.)

  Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig/all" (with no quotes), and press the Enter key.   Copy all results in your next post.  To make the copy, highlight the results, and then use the keys copy (Ctrl-c) and paste (Ctrl-v) keys.  If your "IP address" does not begin with 192.168, then for security reasons, delete the latter half of your IP address.

• I connected a VGA cable and clicked on the option monitor, he did not come on my t v

  VGA?

  I connected a VGA cable and clicked on the option monitor, he did not come on my t, v and the screen is black when I plug cable in the future. How can I get the possibility to save change?

  Perhaps the following links will propose a few ideas:

  How to connect my computer to a TV
  http://hookpctotv.com/

  How to connect your PC to your TV
  http://en.kioskea.NET/FAQ/Sujet-228-how-to-connect-your-PC-to-your-TV-set

  PC to TV cables and adapters
  http://www.SVIDEO.com/PC2TV.html

  Windows Vista-
  Connect your computer to a TV
  http://Windows.Microsoft.com/en-us/Windows-Vista/connect-your-computer-to-a-TV

  Windows Vista-
  HDTV: Frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/HDTV-frequently-asked-questions

  Windows Vista-
  From PC to TV, part 1
  Digital media stream to any room with Windows Media Center and Xbox 360
  http://Windows.Microsoft.com/en-us/Windows-Vista/from-PC-to-TV-part-1-stream-digital-media-to-any-room-with-Windows-Media-Center-and-an-Xbox-360

• Lightning cable I have phone 6

  My charging cable began to wear in less than a year of purchase. And Apple Store refused me a replacement, I'm surprised to see such a bad response to retailer and a poor quality of the product which does not last even a year.

  Why my charging cable is not replaced under warranty?

  Sorry to hear but wear were never part of the guarantee. You must take care when using it.

  BTW, my iPhone 5 (2012), iPhone 5 s (2013), 6 (2014) iPhone, iPhone 6 s & 6 s Plus (2015), lightning cables are always good.

• If I can restore iphone and data sync with iTunes to help uncertified lightning cable?

  Hello guys and girls... I was just curious to know if it is ok if I sync data and restore ios using non certified lightning cable which means I have a Chinese... itunes restores the iphone to ios 9.3.1 perfectly and allows you to synchronize all the music and videos files without saying errors... but is it ok for my iphone? It could damage my iphone or will I get ios works in my camera? My iphone gets too hot during loading and the use of the wifi too... sometimes average 2 times he said cable not taken in charge, but during the restoration and synchronization please help me... im confused... tq for playback

  Hi, I would not recommend using no real cables on Apple devices because they can cause problems. You get also the question of the products not authorized to appear on the screen which can be very annoying and it is because he has not got the necessary cable chip that its not true. The original cable is a little more expensive than the no real but its worth the investment that you don't buy new cables every few weeks. It will work with ITunes and transfer of data, but I wouldn't mind keen charging my iPhone/iPad with a as it is possible that they may cause damage. It's just not worth the risk.

• Can I use my charger Macbook W 29 with a USBC to lightning cable to recharge an iPhone 6 more?

  Apple has launched a new cable USB C lightning. I have a Macbook with charger W 29, I was wondering if I can also use this charger with a USB C to the lightning cable to charge my iPhone 6 Plus, with no risk of damage to the battery of the iPhone. Is there guidance from Apple or not experience from other users?

  If it sends not more then 5volts to the device it cannot harm him.

• PROTECTED M800 auto boot up after connected with lan cable

  Hi all

  I have a problem with my laptop Toshiba Portege M800. I decided to connect a lan cable directly on the cell phone instead of using the wireless feature. However, when I shut down the laptop, it will automatically start upward. But after I unplug the lan cable and stop working properly. Can I know the config to make the laptop does not auto boot up after I closed the laptop with the lan cable connected to it.

  Hello

  I think that the boots mobile upwards because the wake on LAN in the BIOS option is enabled
  Please disable this option (in BIOS), save the changes and restart the device

  Then test this new!

  Welcome them

• After I start my computer dell laptop I connect the LAN cable to run internet ON my laptop but it doesn't detect LAN cable

  Hello..

  After I start my computer dell laptop I connect the LAN cable to run internet on my laptop but it does not detect the LAN cable, using the ultimate32 bites. (But if I connect LAN canble then start computer it works fine)

  Hello

  1 windows operating system is installed on the computer?

  2. do you think that no matter what error message in Device Manager? If Yes, what is the full and exact error message?

  3. What is the number of brand and model of the computer?

  Method 1:

  If you are using Windows 7, I suggest to see the link and try to run the troubleshooter and check if it works.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  The link applies to the Windows Vista and Windows 7 operating system.

  Method 2:

  Check the link and try using the network troubleshooter to fix the problem.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  See also:

  Use Network Troubleshooter event logs to solve network problems

  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Method 3:

  See the link and check if it helps.

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know if it helps.

• The connection between your cable modem, router or access point, and Internet are broken.

  What is the average message "the connection between your cable modum, router or access point, and internet are broken" and how to fix it?  We use internet provider time warner.  Can I access online using mini jetpack, but not through time warner.  Is the problem with our internet service or hardware problem?

  Hello Terri,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of damaged or incorrect network settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Note: You can run utilities times 'Internet connection' and 'network card'.

  If this does not help, use method 2.

  Method 2:
  Reset TCP/IP and check the issue.
  Refer to this article:
  How to reset TCP/IP using the NetShell utility
  https://support.Microsoft.com/en-us/KB/299357

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• I work tech support for an ISP broadband. Get a certain calls lately from connectivity lost on cable connections.

  original title: Refresh TCP\IP Winsock

  Hi all

  I work tech support for an ISP broadband.  Get a certain calls lately from connectivity lost on cable connections (coax to modem, ethernet to the computer).  It seems that some of my old Dos standard TCP\IP troubleshooting commands are outdated.  Could someone please review and criticize the following sequence for accuracy?

  1. START | RESEARCH | ORDER -RUN as ADMINISTRATOR
  2. IPCONFIG/FLUSHDNS
  3. NBTSTAT-R
  4. NBTSTAT - RR
  5. NETSH INT REINITIALIS
  6. NETSH INT IP RESET ... Not
  7. NETSH WINSOCK RESET ... Yes

  Thank you!

  J. William (Bill) Hamill Esse quam videri

  WinSock and TCP/IP update.

  Win 7.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP just replace the command typed with.

  netsh interface ipv4 reset Press enter

  netsh interface ipv6 reset Press enter

  ipconfig/flushdns press Enter

  Restart your computer.

  Win XP & Vista

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  The same processes to refresh the TCP/IP replaces the command typed with.

  netsh int reset Press enter

  ipconfig/flushdns press Enter

  Restart your computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• The blue windows screen Driver_irql_not_less_or_equal 7 when connecting the LAN cable?

  Hi all,
  I just want to ask how to solve Driver_irql_not_less_or_equal windows 7 blue screen when connecting the LAN cable?
  pls help me...
  Thanks in advance...

  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  If you are overclocking stop.  (chances are that if you are unsure if you are, you are not)

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.
  * Zip up the copy.
  * Join ZIP archive to your message by using the button (attachments) "trombone".
  * Please download to a service like Skydrive or "Rapidshare" to share files and put a link to them in your answer.

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.
  * On the Advanced tab, click Startup and recovery... Settings button.
  * Make sure that automatically restart is unchecked.
  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).
  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.
  * OK your way out.
  * Reboot if changes have been made.

  Please also run MSinfo32 and download the output as well.

  To run MSinfo32 please go to start > run > MSinfo32
  Go to 'file', 'save' and download the PDF is saved with the DMP
  (Instructions for XP, Vista, Win 7, Win 8)

• Desktop computer connected via a cable to a wireless router - can't print on Photosmart Wireless B109n-z

  Hello

  I have my desktop (Windows XP) connected via a cable to a LinkSys WRT54GC wireless router and wireless HP Photosmart B109n-z connected wireless. I can 'see' desktop printer if I write the IP address of the printer in the browser, but printing does not work.

  I don't know how to set up the printer to print from this desktop computer. What I choose when installing printer drivers (printing via USB or wireless?). I tried manually installing printer but without success. Do I have to set up specific ports?

  Printing from laptop (connected wireless to the router) works perfectly.

  Thank you in advance for your answer, I'm really lost on this one.

  Choose print wireless while installing the software.  Because the printer is connected to your router, you don't need to go through «setup USB wireless»

  I'll try to manually add again in this way:

  Verify that you can access the web page internal to the printer by its IP address.

  1. click on the 'Start' button--> printers and fax machines.
  2. under print jobs, click on "add a printer".
  3. click on 'Next' on the Add Printer Wizard window.
  4. Select "local printer attached to this computer. Deselect "automatically detect and install my Plug and play printer." Click "next".
  5 under, select a Printer Port option, select "Create a new port" and choose "Standard TCP/IP Port" and click "Next".
  6. in the "Welcome to the Add Standard TCP/IP printer port Wizard" make sure that the printer is turned on and connected to the same network that your computer is connected to. click on the button "next".
  7. under "Add Standard TCP/IP Printer Port" enter the IP address of the printer. Click 'Next' and then click 'Finish '.
  8. now select HP in the manufacturers list, select your printer in the list of the models of printers and click the button "next".
  9. If you can't find your printer, you will need to find the installation CD and use the 'Disc' option to select one of the files hp*.ini. You can also select another model of the same type HP printer.
  10. Add the name of print spooler, and then click "next".
  11. click on "next".
  12. click on "Next" and "Finish."

• should my time capsule be connected with a cable for backups, after the initial installation?

  should my time capsule be connected with a cable for backups, after the initial installation?

  If you mean that you have to keep your Mac connected to a Time Capsule via Ethernet for future backups, then the answer is no. Time Machine and time Capsule are designed to work over wireless for your Mac would just need to be connected to the wireless network provided by the time Capsule.

• When I connect the HDMI cable to my laptop, the screen goes black and I can't lift the office unless I get out the HDMI cable

  When I connect the HDMI cable to my laptop, the screen goes black and I can't lift the office unless I get out the HDMI cable. It happened all of a sudden I used he linked TV to catch-up on TV episodes until last night when it happened out of the blue!
  Can someone please help with this.

  Contact the manufacturer of your laptop.  Also - that there might be a key combination for your laptop that changes the screen from the main output is - look at your documentation or on your keyboard for such a combination of keys (what kind of computer is? Make & model...)

• Planning to get a plus the HD antenna. How can I connect the coax cable to my STR-DH820?

  Hello

  I'm trying to free myself from the grip of DirecTV expenive.  I'm looking to well reviewed on the air such as the Clear Stream 2V or 4V HD antennas.  How would connect the coaxial cable from the antenna HD to my receiver STR-DH820? Currently, DirecTV coaxial cable runs in the DirecTV DVR, which then has HDMI output in the DH820.  My Sony S590, PS3 connects to the 820 and I have a HDMI going in my Sony KDL-55HX729.  Thank you!

  I did a little research... Looks like I have connect the coaxial cable to the TV antenna input and the "Digital Optical Out" in the "TV digital optical In" 820 receiver.  I can tune the channels of sound with the TV remote control and select 'TV' on the STR-DH820 to switch the sound of the home theater.  Does this sound right?  Seems a bit of work, but if it works, it is better than $100 a month from DirecTV!