Downloading purchased content after resetting the laptop

Similar Questions

• Hello. There is a problem on the IPhone s 5 - after reset, the display flashes on the sides for 10 minutes, then the flashing stops. And the problem does not appear again until they do not use a Hard Reset (Power Home). The phone is new (5 days). It's a m

  Hello. There is a problem on the IPhone s 5 - after reset, the display flashes on the sides for 10 minutes, then the flashing stops. And the problem does not appear again until they do not use a Hard Reset (Power + Home).

  The phone is new (5 days). It's a wedding?

  If you encounter this flicker, then the next troubleshooting step is to restore from a backup. If the behavior persists after the restore, then the last step is the factory restore. If after the factory restore and adding no additional content, you see always this problem, then you must make an appointment at the Genius Bar to the nearest Apple store or service provider authorized Apple to have the material examined. If the behavior goes after the factory restore, then sync again your content manually, without using the backup. It seems to me it's corrupted content in the backup.

  Restore your device from an iCloud or iTunes backup - Apple Support

  Use iTunes to restore your iPhone, iPad or iPod settings - Apple Support

• I was somehow infected and after restarting the laptop, it goes to a white screen.

  Original title: Virus

  I have an old HP Pavilion 2008. I was somehow infected and after restarting the laptop, it goes to a white screen. Not even the HP logo lights up. I can't access installation even though I know which key press.

  I created a bootable windows DVD 7 and a USB port. I can not even boot from one of them. With the DVD, it sounds like it wants to read, but there is something else wrong.

  Any help would be greatly appreciated.

  If the HP logo comes and you can't access BIOS, the problem is more likely to be at a lower level. A failed HARD drive should not prevent you from access to the configuration.

  Several things can cause the logo appears at the top (I write from a HP Pavillion 2008). I've dealt with many laptops such as yours and have seen many causes. Faulty RAM memory is a. A problem with the video chip is another. In fact several kinds of tokens (two bridges, video..). A virus is more unlikely but not impossible (if he messed with your BIOS, it is possible).

  If you don't see movement in your DVD or HARD drive, something I'm leaning more towards the video chip. Especially if it's Nvidia or Radeon - it would be a miracle if you use an HP laptop of 9 years with a powerful video (so that there is time) without having had any problems with it until now (mine is Intel). They overheat easily.

  What I would do in your case:

  1. remove the battery and unplug the unit. Give it 10 minutes and see what happens. Small chance, it would be useful, but it's easier to test.

  2. If you are reluctant to remove anything yourself proceed to 4. Otherwise, open the case and look for a reset (might want to read in the manual how to do it), remove the internal battery.

  3 try to remove the first (try to run) then the other of your plates to RAM (assuming you have two). During the race, all the tests remove the drive HARD and DVD just to eliminate the possibility of interference. If you manage to get started and get the logo and enter BIOS start adding parts back one by one and you will find the faulty one.

  4. If it at a gas station. Now you can do anything, if you can not enter BIOS so it must be a hardware change.

• Can't DOWNLOAD purchased product after order received email Confirmation. WIN8 IE10 pro

  Can't DOWNLOAD purchased product after order received email Confirmation. WIN8 IE10 pro

  Hi timbalai,

  Please use the link given below to download Acrobat XI

  http://prodesigntools.com/Adobe-CC-direct-download-links.html

  Thank you

• Restoration of old keychain after resetting the default keychain

  Restoration of old keychain after resetting the default keychain.

  I have "reset my default keychain" in Keychain Access after learning that he was the new version of "first aid" on the update OS X El Capitan.

  He said that a new keychain will be saved by default and moved my old side (but not deleted)

  I want to restore my old bunch who was moved aside but can't seem to find all the information on how to do it.

  Thank you very much

  Elliot

  The old keychain must be in ~/Library/keychains.  Rename the old keychain back to login.keychain.  If you do not know the password for the keychain of old connection then you will not be able to unlock it.  The old login Keychain password is different from the user account password, you'll want to change the corresponding password.

  

• is it possible to save the Office XP for multiple monitors and restore after using the laptop in mobile mode?

  Is it possible to save the Office XP for multiple monitors and restore after using the laptop in mobile mode?

  Hi Kenelms,

  You can follow this link & check if it helps.

  HOW to: Set up hardware profiles for laptop computers in Windows XP

  Hope the helps of information.

  Please post back and we do know.

• After resetting the NVRAM C309a rejected all new cartridges

  How to fix c309a after resetting the NVRAM rejected all new cartridges, for an ox610000fb mistake made semi nvram reset done

  after reboot, asking all the cartridges to replace? help is appreciated.

  Unfortunately, I think that the printer is irredeemably right now especially if you did a reset full semi and still get an alphanumeric message. I have a document that I can link to for you on the error codes alphanumeric on this printer, which I will give you. But at this point, you must call to HP Total Care for assistance. Here is the link to this document.

• After resetting my laptop, wifi is not available.

  Original title: wifi unavailable

  I have reset my laptop it is an acer windows 8

  Since my laptop wifi option has dissapeard I must now plug the modem which is a problem because of the work of the school

  pls help

  Hello

  You probably just need to re - install the drivers WiFi or WiFi could be disabled
  (some systems have physical switches or keyboard shortcuts.

  Check with the Acer Support, their drivers and documentation online and ask in their forums
  on known problems.

  Acer - USA - Service and Support - Chat - drivers
  http://us.Acer.com/AC/en/us/content/support

  Acer - Community/Forums
  http://community.Acer.com/

  Acer - worldwide
  http://www.Acer.com/worldwide/

  ===========================

  Free Wi - Fi and wireless problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Why can't I connect to the internet?
  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-8

  Note the use of Win Key + X and Win Key + W (to access control panel, run,
  and settings according to needs). Win + D key calls to the office and use
  Win Key activates / deactivates the desktop and start screen.

  --------------------------------------------------------------

  Control Panel - Network and sharing Center - solve problems

  References to Vista also apply to Windows 7 and Windows 8.
  
  Your router be guess here, you have successfully updated the firmware a possible
  solution? And I would update your WiFi drivers on computers. How far away are they
  you have set in the router? Are there obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click
  top - tab of the driver - write version - click on update driver (can't do
  nothing that MS is far behind the certification of drivers). Then right click on the Wifi
  Device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Microsoft - How can Windows 8 - I fix the network adapter problems? (Do not forget to see
  This section-> update the NIC driver).
  http://Windows.Microsoft.com/en-us/Windows-8/fix-network-adapter-problems

  Drivers and Microsoft - Windows 8 - Hardware
  http://Windows.Microsoft.com/en-us/Windows/hardware-drivers-help#hardware-drivers-help=Windows-8

  Microsoft - Windows 8 - why Windows is not find my device?
  http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

  Microsoft - Windows 8 - what happens if a device is not installed correctly
  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system Maker you can see the same device manufacturer
  more recent versions. (Those become your fonts of rescue system manufacturer).

  Repeat for network (NIC) card and is a good time to get the other update
  Drivers Windows 8 like updated drivers.

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - set up a new connection or network

  -----------------------------------------------------

  And:

  TechingItEasy - how to join a Wi - Fi network in Windows 8 by MVP Andre Da Costa
  http://techingiteasy.WordPress.com/2012/06/09/how-to-join-a-Wi-Fi-network-in-Windows-8/

  Microsoft - Windows 8 - Web & Networking
  http://Windows.Microsoft.com/en-us/Windows/Web-networking-help#V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1&Web-networking-help=Windows-8

  Microsoft - Windows 8 - Wi - Fi & Networking
  http://Windows.Microsoft.com/en-us/Windows-8/WiFi-networking#1TC=T1

  -----------------------------------------------------

  Microsoft - Windows 7 - Why is my Internet connection so slow? (applies to Windows 8)
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-Internet-connection-so-slow

  Microsoft - Windows 8 - wired and wireless in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• How to reset the laptop to stock settings

  I want to reset my laptop to its stock settings by erasing all how can I do?

  Currently, I bought a used laptop and the person who sold it to me was not to erase everything on it, so I want to know how to erase everything and get the stock settings.

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  See you soon.

  Mick Murphy - Microsoft partner

• After resetting the iPad to default it show that the power cord is trying to connect to iTunes

  I got an iPad 16 GB factory reset default after a while display only the power cord going to iTunes, need help to get this operational back, it worked Ok before resetting all we have tried to make clear the former owner information

  The iTunes icon and cable image means he went into recovery mode, you will need to connect it to iTunes to your computer to reset the iPad, and you can then restore/resync your content.

  If the previous owner had not disconnected from the settings > iCloud on it and find my iPad has been activated, you will need to communicate with him or her: disable find them my iPhone Activation Lock - Apple Support

• Pavilion dv7: no internet after resetting the computer

  I don't know if I am posting this in the right advice.  I had to do a reset on my Pavilion dv7 laptop, kept my personal files, but now I can't access the Internet.  It shows that I am connected to my wireless network, but I can't go to all the websites that I go into my browser.  I went to Device Manager and went to network adapters.  I can say that the driver works fine and I don't see the warnings or errors on other drivers in Device Manager.  I am at a loss of what to so any help would be appreciated.

  Hey @Esoxdiver,

  I understand that you are experiencing you encounter some difficulties to connect your laptop in WiFi and I want to help.

  Here is a list of steps that solve common problems with wireless connectivity.

  First of all, we have a step by step guide to guide you through the process of diagnosis here:
  Troubleshooting your wireless network and Internet access

  A second option is to try the following steps:
  Network power cycle:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.
  
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.
  
  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.
  
  Test an Ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.
  
  Test another connection:
  Many people excluded their home network as a problem if another device working on the same network. Networking is not as simple as that. Each device interacts differently with your router or modem and it is impossible to exclude the settings for this device until the laptop has been tested on another network.
  
  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down menu in the upper right corner of the document.

  The above steps are presented by @Great-Christine-Tree

  I hope this helps. If so, please hit the Thumbs Up and accept as a Solution.

  See you soon,.

  TechSurge.

• How can I restore my passwords in the keychain after resetting the PRAM?

  I have reset my PRAM on my iMac 24 "after some wobbly behavior.  Everything is going well except that all my saved passwords in Safari are gone.  Can I get back them?  Where should I look?

  Reset the PRAM should have no impact on your Safari passwords. I would recommend realized a report of EtreCheck and announcement to your response to this message. Simply click on the link, download the application and view the results of the report in your response to this message. The report will indicate any question obvious cause of your problems.

  If you want to learn more about EtreCheck, please click on the link.

• Y700 - Dolby Audio does not work after resetting the system

  After resetting my computer to factory settings, audio dolby does not work. This is the error message I get:

  "Your installation is missing components. Reinstall the audio driver or the stand-alone components available on the support site for the manufacturer of your PC. »

  His works on my computer, just not this request.

  Thanks for the help.

  Matt

  I have the same problem, I have a 70-Z40 and the Dolby Digital Plus open, but does not work, you can choose the profile but is not even, I have this problem after the last windows 10 updated a few days ago.

  I hope you can help, thanks in advance

  EDIT: I solved it after a few tries, I don't know if it is the best way, but it's how I solve this problem:

  (1) Delete last windows update (after that, it did not)

  (2) delete the sound driver from Device Manager and reboot (it did not)

  (3) download the driver for my lenovo model page and install it (it did not)

  (4) any uninstall Conexant audio and Dolby of my computer and re - install again (it does not), it seems that my dolby 7.6.4.9 driver version is not correct, I need the 7.5.1.1

  (5) again to uninstall everything and restart

  -From there, he solved my problem

  (6) go on my computer (my system is in Spanish, so I don't know the correct name for the version in English, sorry) and then go to the Lenovo partition, then open drivers > Audio > Setup.exe This will install your Conexant audio driver, and then restart.

  (7) after you restart your laptor, do the same thing... Lenovo > drivers > Audio > DolbyGUI > x 64 > DolbyDigitalPlusHT.msi, and then restart your computer and it should work fine.

  Sorry for my English.

  See you soon

• Network printer stops working after restarting the laptop

  I have 2 PCs both running windows Vista. A PC is a desktop computer ACER with a printer connected to a USB Port (HP Photosmart C4480). The 2nd PC is an ACER laptop also on windows Vista. I have a network home and print away from the laptop. Problem is when I restart the laptop I can't print remotely and do are Add' the printer again. Print spooling is nec automatic and active. I have downloaded the latest drivers HP for the printer. Just a note to say that ACER laptop my son who works in XP does not have this problem and can print after a reboot.

  Hi GaryPolaris and thanks for the answer.

  What is the brand and model of your printer? Have you checked to see if the printer is compatible with Vista? You can check this in the Vista Compatibility Center located at this URL http://www.microsoft.com/windows/compatibility/ . Also, you can try installing the Vista drivers on the XP machine. If the manufacturer has released Vista drivers simply download and install the drivers on your XP machine.

  I hope this helps. Please post back and let us know if it did or did not solve your problem.

  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Error Microsoft Visual C++ Runtime Library after that the laptop closed due to battery care

  Original title: Windows 7

  Dear Sir.

  I'm using windows 7, I was working with internet using airtel dongle, because of the discharge of the battery, the laptop shutdown.

  After I try to start the airtel connection but it shows "Microsoft Visual C++ Runtime Library.

  I uninstalled the program and re installed but encountered same error.

  I use airtel dongle on the other system, on this dongle is good work.

  All professionals have a request to say the solution.

  chk if visual C++ is installed on the computer, if not install it and check.

  Later supported Visual C++ downloads

  http://support.Microsoft.com/kb/2019667/en-us