Driver NOR-executable daqmx / does not start

Similar Questions

• Satellite M70 - after HARD drive partitioned, the OS does not start

  Hello

  Good then this is a real doozy, and I hope that someone will help.

  I started to fix my satellite m70 girlfriends using the disc of recovery etc, everything went fantastic, the HARD disk has been erased and Windows + all software has been reinstalled.

  Then I thought it would be a good idea to use partition magic to partition the hard drive, so I chose the main hard drive and cut 10GB of it to put in place a new partition.

  I rebooted, and then after Windows restarted again completed.

  NOW, it does not charge, it says no operating system, so I tried to start with the recovery disk and all over again...

  If I click on continue (to start the recovery process), however it is said now that the "Error #1828", free space is too small.

  I'm really angry that this has happened and I just want to start over again.

  Can someone help me with this?
  I can't access the Bios either (not sure if that might help), because I don't know the password (must be a fault im not aware of).

  Help, please.

  Thank you
  SG

  I think that this is the reason why you used a tool to change the size of the partition. At best, this should be done before you install Windows and 10 GB is a little too small for Windows. You must use at least 15-20 GB for the first partition where the BONE is placed.

  To resolve this problem, you must delete all existing partitions before using the recovery disk. Therefore, you can use a Windows XP disk or something else. Just boot from it and delete all partitions. Then the recovery disk should work.
  Check it!

• replaced the hard drive, Illustrator CS4 now does not start

  After that I replaced my Mac (paid by Apple, fortunately) Fusion defective hard disk and restored everything from a Time Machine backup, Illustrator CS4 gives me error 150:30 when I try to run, with instructions to contact Adobe support web site. All I get there are some frequently asked questions and their cat gives suggestions repeated to try the forum. I'm surprised research here do not find other people who have had the same problem. I would have disabled AI CS4 before hand, but the disk failure came quickly and by surprise.

  I've logged into my Adobe account and could see my products, but could not find anywhere to administer anything, like resetting of the authorized computers one can in iTunes.

  Does anyone have a suggestion? I would of course welcome.

  Thank you

  Rick

  Contact support to reset the activations, run the cleanup tool, and reinstall it correctly. There is no magic involved and I'm sure that your own web searches have come up with the same instructions, even if you seem to refuse to recognize them as the correct procedures.

  The Adobe Creative Cloud Cleaner tool allows to solve installation problems

  Download the CS4 products

  Mylenium

• How to run the installation on a 5 GB pcmcia hard drive, it does not start?

  I have a computer dell laptop, which has a non-functional drive Bay, so I use a 5 GB kingston pcmcia hard drive. Recognizes the xp home installation cd and copy of files, only I does not start when the system is restarted, is it a boot disk to start just xp? The bios doesn't have the ability to start from pcmcia, only an ehernet PCMCIA.

  Can I create a boot cd which recognises the pcmcia from the Setup disk, or add the driver pcmcia on a boot disk and which record a bootable CD?

  Hello

  Thanks for choosing Microsoft Community!

  You have reached the right forum. Try to solve this problem together.

  If I understand correctly, you are trying to install XP on a PCMCIA drive and the computer does not start after the installation files are copied during installation.

  Since then trying to install XP to a PCMCIA drive and the computer does not start after the installation files are copied during installation. In addition, the BIOS has not an option to boot from PCMCIA readers. So basically, you will not be able to install XP on the PCMCIA drive.

  Regarding the question on a boot disk, Microsoft provides no such discs. You will need to do a search online or in the stores of tech for such a disc, if it is available.

  Warning: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope the helps of information. Reply with more information if you need further assistance, we will be happy to help you.

• SSD external via USB does not start by default

  Hello Apple community.

  I have a problem with my new external SSD. Given that the base model Mac Mini end of 2014 comes with a disk HARD 5400 RPM drive, I wanted to go to an SSD without having to tear the whole unit. I wanted to exhaust the option 'boot from USB' and I'm having a strange problem. I cloned my Mac to the new drive SSD and slapped in a box set of the speaker. I connected via USB and changed my 'startup disk' to use the external SSD drive. However, it does not start on this unit automatically. When I reboot and discovers the "boot manager" I see the USB being initialized automatically. After disconnection / re - plug the drive in, it appears as a boot option. Once it is initialized, everything works fine and I can boot into El Capitan without any problem using the SSD.

  I am trying to find a way that I can get the Mac to initialize the SSD to the boot upward and choose default. I don't want to have to re - connect the drive whenever I want to start on the SSD drive... Any help and suggestions are greatly appreciated!

  My equipment

  ===========================

  Model Base of Mac Mini (end of 2014)

  1.4 GHz Intel Core i5

  4 GB of DDR3 1600 Mhz

  OS X - El Capitan v 10.11.3

  240 GB SanDisk SSD more - connected via USB3.0

  What unit do you use for the SSD?

  Can you provide a link?

  If the SSD is delivered with a box to provide a link to that,

  How do clone you for the SSD? What app did you use?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable, reinstall the OSX. Nothing shall be lost

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• B560 does not start

  Hello

  My B560 does not start immediately when you press the power button - today it started after 90 minutes!

  I installed energycut, tried to run the Tower discharge of static electricity T61, removed from the RAM, swapped the hard drive, but still it does not start immediately.

  Any ideas?

  Thank you

  Garry

  I'll be back my laptop yesterday - the report says that the motherboard has been replaced.

  Fortunately, the startup problem is fixed.

  See you soon,.

  Garry

• 7 does not start with a connected external Western Digital hardrives.

  I have two external hardrives WD, connected to a pc to the bridge under windows7.  When the hard drives are connected, Windows7 does not start.  It hangs on the black screen.  Without the disks attached, it starts very well.  Anyone know what I can do to not having to pick up leads outside whenever I want to start?

  Solved.

  Use Windows Update to install the update from Western Digital Technologies WD SES device released by Microsoft in January 2011.

  My system hangs is no longer with USB Legacy Support set to 'Auto '.

• I deleted the boot camp trying to resize the hard drive on my mac pro book. now, the computer does not start without a bootable device, which I don't have, and any download must be on a windows machine. Can anyone help

  I deleted the boot camp trying to resize the hard drive on my mac pro book. now, the computer does not start without a bootable device, which I don't have, and any download must be on a windows machine. Can anyone help

  1. did you remove Bootcamp using disk utility?

  2 have you tried local restore or recovery of the Internet? - OS X: on OS X Recovery - Apple Support . Mac with built-in optical drives may need 'Gray' disks to boot the system.

• Toshiba Q300 480 GB HARD drive does not start after migration

  Hello

  I bought a disc of Q300 489 GB to replace a small 840EVO of Samsung. I used the toshiba tool to clone the smallest to the largest player. However when the clone is finished and the reboot of the machine the machine hangs just at the start of the process (before starting windows 10). If I go back to my little samsung it starts without a problem.

  I tried to treat twice with NTIEcho and also tried with Partition AOMEI tool, all attempts have failed to start on the Q300 drive.

  I am just tempted to refer the reader to Ebuyer, getting another Samsung. Maybe Toshiba can tell me how to get the drive working properly?

  Regards Sean

  PS. can someone direct me to a page where I can raise a ticket of Toshiba, I would be grateful. There seems to be some links broken on the UK site.

  Hello.
  Do you have an error message when the operating system does not start? Appearing in AOMEI Partition Wizard you have been used during the replacement of the Samsung drive?
  After the largest disk cloning, you may need to change the boot settings in the BIOS or to remove the previous Samsung drive to test.

• computer does not start with attached external hard drive

  I have the 4540 s if an external hard drive is connected, it will not start.

  I have the internal hard drive set as master boot.

  The message that appears indicates Press esc, to enter the boot options, but which does nothing.

  I spent an hour with hp support-useless.

  I did a BIOS update - no help.

  All advice appreciated.

  Not sure what you mean about the reference of the warehouse.

  I've updated the USB ports and that solved the problem.

  Thanks for the reply.

• Satellite Pro 460 does not start with the new drive in

  I recently received a Satellite Pro 460, but he had no hard drive.
  It starts great without a disc in but as soon as I put a new hard drive in it does not start.

  I thought that it might be again a hard drive, so I pulled out my old Toshiba Satellite with my old drive to work, and yet, it does not start.

  Someone has any ideas why this is and what I can do about it

  I think that you can not do much. Satellite pro 460 CDT, for example, comes with 2 GB of HARD drive. If you try to get it work with similar HDD without success, it may be defective IDE port on the motherboard.

  What HARD drive you are trying to use on this good old classic?

• HP 500-281: does not start a 2nd drive cloned in sata1

  HP 500-281 desktop

  Win 10 home

  BIOS MEMv80.22

  Short version of the latest issue:

  Fine Win10 after upgrade to 10 at the start of the hd0 in sata0 slot (original). HD1 in sata1 slot is a new clone of HD0 (Win10, using Reflect). HD1 and its files in Windows more HD1 is seen in the BIOS. If the boot order is changed in the BIOS will not start (sata1 above sata0), saying "no boot disk. Boot order reset default (sata0 and sata1). If the HD0 data cable is disconnected, does not start, once again "no boot drive" Boot order is reset by default. Cable data Sata0 off HD0 and HD1-connected, with no data connection to HD0. Now, she starts to HD1. How to start the HD1 connected to sata1 with or without HD0?

  Greetings,

  UEFI is ruthless.

  The cloned drive should be connected to the port SATA (SATA0) where the source drive has been connected.

  The cloned drive does not start on the SATA1 without modification.

  See you soon!

• My C50 - B Satellite does not start from the HARD drive

  Details of the machine: -.

  Model number: PSCMLA-03F07Q
  Serial number: XE343127P

  Computer does not start from hard drive. No error message, just the start Toshiba at the end of self-test screen.

  Sometimes a reinstall of the operating system seems to correct the problem, but then he would go again, now the problem is consistent.

  I reduced the possibilities to a fault of BIOS, reasons.

  System boots from USB with no problems. Installation of operating systems is done without error. SMART hard drive data indicates a perfectly healthy hard drive. Memcheck will return no error.

  The obvious solution is to reload the BIOS, just reset it doesn't help. But that is the problem.

  1.4 BIOS update that the Australian site offers is a Windows program and the computer cannot start Windows.

  Obvious answer is to use a bootable USB key with an operating system 'live' on this issue, but all of these systems are Linux and the update of the BIOS is a Windows program. So much for smart solutions.

  Downloaded Bios version 1.7 of the European site but the iso inside the rar file is empty, 25 MB in size but nothing in there according to Linux. Tried to run his program on a Win7 64 bit computer and it returns an error that it could not find the correct iso file.

  I submitted a support request by email to Toshiba, but they believe that it could take three days to get a response, so I thought I would ask here as well. Can someone tell me please to a working copy of the latest BIOS update disk for a laptop Satelite C50 - B? Note: this model does not have a CD player so iso should be compatible with USB boot.

  See you soon,.

  Andrew.

  Hello

  From my experience that I n think that BIOS update is the final solution for you. When you set the default settings of the BIOS disk HARD appears correctly in the BIOS settings?
  HARD drive is also offered and listed as boot device when you enter in the start using F12 at startup menu?

  What happens when you start using recovery image installation created recovery USB key (I hope that you have created a)?

  Offer BIOS updates are versions of WIN and can be performed by running the Windows operating system.

• HP envy Phoenix: win 7 does not start with connected external hard drive

  I have a desktop HP Envy Phoenix with i7 chip and an SSD for the OS.  If I connect via USB external drive of 3 TB WD for the backup of the system does not start while it is attached.  The pc seems to be trying to boot from the outside, can't find the OS and does not start.  It will start fine with small external drives connected.  It is the size of the disk? Is there a way to fix this?

  Hello

  The WD drives seem to pose problems of my potential.  I have used other brands such as Seagate and Hitachi without running into problems with external USB drives causing the system to boot.  Maybe it's the USB adapter that I use which does not cause starting problems.

  @tpetras

  I used the adapter HP USB 3, which uses drivers NEC or TI and has never had a problem starting via a USB external (non - WD) readers.

• After the new HARD drive does not start installation Qosmio G15

  I just got this G15 last week and one of the hard drives was bad. Put it in a new Bay 2 and it does not start. I took it back and it starts fine. I even changed the main hard drive Bay 2 HD and it starts up fine with a hard drive. It's something to do with the scores, I think. Any help appreciated.

  Hello
  I think that the boot order has been the bad HARD drive in the BIOS.
  At the new disk you do not installed any OS, and in my opinion, this is a reason for starting problems.
  Simply access the BIOS and change the boot order