Driver of Windows 8 when the Blue Snowball microphone usb connection error

Similar Questions

• tried to install a new copy of Windows XP Home. Everything is OK until the final phase, when the "blue-screen" appeared during the installation of the drivers.

  Installation of xp and blue screen of death

  Hello

  I recently formatted the partition boot and recovery of a laptop Medion2230, then merged the two partitions in a single NTFS partition.  Don't ask why, it's a long story.

  Then, tried to install a new copy of Windows XP Home.  Everything is OK until the final phase, when the "Blue Screen of death" appeared during the installation of the drivers. Restarted and installing XP as normal to repeat the first onboard staged and went to the "blue screen" at the same point as before.

  Using some diagnostic software, I reformatted the drive again, loaded XP set up and I had the same problem.

  Someone knows what to do?

  Thank you allionii123

  Now solved and pc with Windows XP home.

  Discovered a trick online, who said that at the beginning of XP installation, press F5, and this leads to a screen option - select 'standard pc' and continue with the installation of XP.

  (Again), formatted hard drive ran XP installation and followed above point.

  Worked the first time.

  Thank you very much for your advice.

  I think you can pressing F5 or F7...

  How to impose a layer of HAL during an upgrade or an installation of Windows XP

  Impose a HAL

  To prevent Windows XP to automatically determine the system HAL during the upgrade or installation of Windows XP, you can manually force in a system HAL. To impose an Abstraction Layer HAL during a upgrade or installation of Windows XP, follow these steps:

  1. During the phase in text mode of Setup, when you receive the message at the bottom of the screen, press F5:
     Press F6 if you need to install a third-party RAID or SCSI driver.

     Note If you press F7, the Standard PC HAL loads and the ACPI enforcement is bypassed.

  I would not need this except in the systems of many older and low end... :-(  After all, in the same article, for Standard PC they say: "the CPU can be a 386, 486, Pentium, Pentium II, or Pentium III '...

  Thanks for letting us know what you were doing.  Do you have all the necessary drivers after loading Windows XP?  I would not recommend using the default drivers for any hardware - always see what the manufacturer offers on their web page for each component of your system - card motherboard chipset, audio, video, network devices, etc.

• Audio loss. UAA Bus Driver reads Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39). All the patches?

  Audio loss.  Device Manager indicates Microsoft UAA Bus Driver as: "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) ».  Tried to update driver and restore without success.  Tried the program of "Fix - It", which has identified an error with the sound system, but said that he could not fix it.  Restored to an earlier date but still what system did not go.  Tried to uninstall and reinstall the driver.  Uninstall was successful but reinstall it read that the hdaubus file does not exist.  I'm a computer dunce.  Any help out there?

  Hi BarbaraWolfe,
   

  There are many causes of Code 39 errors:

  • A required device driver is missing.
  • A required binary file is corrupted.
  • There is a problem with the file I/O process.
  • A driver that refers to an entry point in another binary file cannot load.
  Re-install the driver by downloading it from the link given:
   
  Universal Audio Architecture (UAA) High Definition Audio class driver version 1. 0a available for Windows XP, Windows Server 2003, and Windows 2000
  Additional reference on:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  Check if that helps.

• How is it that some machines running windows vista, when the router is updated or changed, they show "limited or local only" when you reconnect then wireless.

  problems with wireless Vista "local only".

  How is it that some machines running windows vista, when the router is updated or changed, they show "limited or local only" when you then reconnect wireless... nothing else was changed on those computers and other devices can connect ok?

  Hello

  Each router is assigned to the specific address (called IP address or IP address). And each router maintains its own database (called as base of router) to follow the networking devices communicate with him. When the router is changed, the particular router is unable to detect the device, especially the network card to communicate with the computer.  Since he does not have details of the database of network devices, communicate with him.

  • You are able to access the Internet?

  Try the steps mentioned below and check:

  Method 1:

  Step 1: Enable or disable a network adapter and then check:

  http://Windows.Microsoft.com/en-CA/Windows-Vista/enable-or-disable-a-network-adapter

  Step 2: Run Network Diagnostic tool and check:

  Network connection issues: http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Method 2: Wi - Fi and in Windows network connection issues:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Reference links:

  Of network connectivity status incorrectly as 'Local' only on a Windows Server 2008 or Windows Vista-based: http://support.microsoft.com/kb/947041

  Setting up a wireless network: http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  Connection to wireless with Windows Vista: http://technet.microsoft.com/en-us/library/bb878035.aspx

  Hope it works.

• So basically I can't extend my 3 TB hard drive 3 TB because windows 8 is the treatment as a MBR. Error [0 x 80042468]

  So basically I can't extend my 3 TB hard drive 3 TB because windows 8 is the treatment as a MBR. Error [0 x 80042468]

  Background: after a bit of trouble to install windows 8 on my SSD, I had at one time install on my drive 3 TB of seagate for troubleshooting. Of course, this has reduced the reader to 2 TB for the MBR. I finally solved the problem by changing the mode AHCI instead of IDE interface and installed the OS on my SSD. To my dismay, I could not reclaim the unallocated space.

  I tried to format the drive and delete volumes using disk management, windows 8 installation disc command prompt (you have the option to format and remove the disks and volumes). Basically, I'm stuck. I can't extend the volume. Windows 8 install disc gives me the error [0 x 80042468]

  There is a similar problem but I can't access the answer. (ACCESS DENIED)

  * edit * there is no system of operating on the 3 TB drive, it is completely on the SSD.

  Hello

  Thanks for posting your question on Microsoft Community!

  After your description, it seems that you have a problem with the extension of 3 TB hard drive.

  I would like the season go the following information.

  I suggest you to see the steps in the link.
  http://support.Microsoft.com/kb/2604034

  You can also refer to:

  http://msdn.Microsoft.com/en-us/Windows/hardware/gg463525.aspx

  http://support.Microsoft.com/default.aspx?scid=KB; EN-US; 2581408

  I hope this helps. Please let us know if you need assistance, we will be happy to help you!

• Blue Snowball microphone installation with adobe first elements

  Blue Snowball microphone installation with adobe elements first problem - acts as the mute

  Hi William,.

  1 - is the mic function in other Audio capture programs?

  You can try to adjust the microphone as default and check if the problem persists.

  a. right click on the volume icon in the tray and then click "recording devices".

  b. make a right click on the empty spot in the window pop up, and select "Show disabled devices" and "show disconnected devices".

  c. right click on Microphone and then click 'enable '.

  d. highlight the microphone, then choose "Set as Default Device".

  e. click apply and then click ok.

  Hope this information is useful.

• How can I reinstall windows xp when the computer does not start and there is no cdrom/dvd drive?

  I have an Acer netbook aspire one.  It will not boot past the windows logo.  I have a windows xp disc to reinstall windows, but the computer has no CD or dvd rom.  Can I copy cd of windows xp on startup SD memory card and reinstall windows?  Or can I run connect the non working pc a working PC to access the cdrom on the work pc to reinstall windows?

  First of all, you are mistaken when you say that the PC does not start.

  This is clearly starting. The problem comes from Windows, not with the real PC. It's actually a very important distinction!

  There are methods to repair Windows, but they can be a bit tedious. By all means, follow the advice given here to do if you're so inclined.

  If you would not rather to repair Windows (and I think it's interesting a try) or your repair attempts are unsuccessful, apparently, you would need to use an external optical disc drive and follow the instructions here:

  http://Acer.custhelp.com/app/answers/detail/A_ID/2631

• Windows XP SP3, the blue screen and restart loop

  I use Windows XP SP3. I have the blue sreen of death and I'm in a reboot loop. I don't have a CD with the operating system, as was pre loaded on the laptop. on the blue screen of death, let me stop error:

  STOP: 0 X 00000024 (0 X 00190203, 0X8713F238, 0XC0000102, 0X00000000)

  Can someone please help?

  This error indicates a problem with the NTFS file system.

  You will not be able to boot in a mode any, until resolve you the file system.

  You need start in the XP Recovery Console and run chkdsk /r to see if he's going to clean it up.

  Here's how:

  Boot into the Recovery Console Windows using an XP bootable installation CD.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• \device\harddisk3\DR3 window appears when the screensaver of my picture is on

  When my screen saver comes up in my photos. "A window appears which says: ' there is no disk in the drive. Please insert a disc.  My Screensaver doesn't always work, but this window blocks.

  Hello

  1 how long have you been faced with this problem?
  2. don't you make changes on the computer before this problem?
  3. you have any advantage wire screen saver, installed on the computer?
  4. What is the full error message?
  5. where these images are stored?
  6. have you set up any removable drive with the drive letter C?

  In response to the questions above could help us help you better.

  Search for the issue in the clean boot state.

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  Similar problem: http://answers.microsoft.com/en-us/windows/forum/windows_7-desktop/screen-save-works-but-get-error-dialog-box/38e7597c-01b9-4919-b43b-f54b46e121f1 (the steps described in this thread can also be tried on windows XP)

• Installation of the driver software window opens on the second monitor in a dual monitor extended installation of the monitor

  The "Software Installation" window will open on the second monitor in a dual monitor extended installation of the monitor

  I have a dual display setup. A 225WS 1680 x 1050 monitor LG is connected via a VGA cable and a VGA - DVI converter to a DVI port on a Radeon 6850 video card. The second screen is a Samsung HDTV set at 1920 x 1080 and connected via HDMI on the same video card. I have set up the screen LCD as main monitor and the Samsung HDTV as the extended display. HDTV is most of the time, but I use it at least once a day. This isn't a driver problem, because it happened also when I had an old Nvidia video card and it is fixed by a new installation of windows and setting up of screens from a square.

  The installer works great almost all the time except when I try to use some programs or Windows functions (7). When I try to start the MozBackup application or I pop in a new usb device and click on the notification bubble, both these windows (MozBackup and the "Driver software Installation" window) open in the center of the HDTV as opposed to the LCD (which is defined as primary). The problem is that the views are ~ 3 meters out and HDTV is mostly off.

  I sent a bug report to the developer of MozBackup because this part is perhaps a problem with its software or what old Windows functions and hooks it uses, but the window "Installing the driver software" (or who knows what other program Windows Basic) has exactly the same problem and is part of Windows.

  What can I do about it? I DIDN'T put the displays in any mode "clone" to have office in mirror between them. Is - this fixable somehow? I guess that is not a problem with the video card drivers because I used two different video cards with either the manufacturer or windows update drivers and the problem is the same.

  I'm talking about a window similar to this one
   
  http://jaunty-electronics.com/blog/wp-content/uploads/2012/09/Freedom_FRDM-KL25Z_driver_install.PNG

  Try changing the backup.ini

  you find it in

  .. \Program files (x86)\MozBackup\backup.ini

  Open the file backup.ini with editor

  Check if you have the rights to save the changed files in this directory. You may need to change the Directory rights

  Change the value of "1": monitor

  wyzodir =

  ; Monitor: the monitor number where MozBackup window will appear

  monitor =1

  '2' or whatever the value of your primary monitor is:

  wyzodir =

  ; Monitor: the monitor number where MozBackup window will appear

  monitor =2

  System main screen could be identified as '1 '. If you have changed the monitors, it can be used internally '2 '.

• Windows Media Player 12 freezes windows 7 when the music streaming

  the computer completely shuts off when it freezes caused by WMP 12. I have tried to uninstall, reinstall, troubleshooting. the result of troubleshooting is always like this:

  Windows Media Player settings

  Publisher details

  Problems found

  Configuration settings can be unruly.

  Reset Windows Media Player default settings Completed

  Potential problems that have been verified
  Network streaming settings are corrupt Network streaming settings are corrupt The settings used by Windows Media Player for multimedia streaming over the network are corrupt. This could prevent you from playing the content that is streamed, as opposed to the content that is completely downloaded before it be played.	There is no question
  Windows Media Player not available on this edition of Windows Windows Media Player not available on this edition of Windows Windows Media Player is not preinstalled on some editions of Windows.	There is no question

  Hello silvanfay,

  When you get the blue screen on your computer? What were you doing when it appeared?

  Have you changed your save location of your music files?
  If so, to try to resolve the problem, open Explorer, under libraries, click the music tab and click Properties. Now make sure that your backup folder of choice is defined as your backup location. If not, click it and then click on the button "game save loction". It is perhaps one of your configuration settings which are not correct.

  Have you tried to reset your Windows Media Player in "programs and features"?

  Step 1.
  Uninstalling Windows Media Player:
  1. go to start and in the search type "Turn Windows willing or not.
  2. click on "Turn Windows features on or off".
  3. search for multimedia and uncheck the brand in the face of Windows Media Player.
  4 restart the computer
   
  Step 2.
  Reinstall Windows Media Player:
  1. go to start and in the search type "Turn Windows willing or not.
  2. click on "Turn Windows features on or off".
  3. find the multimedia functions and place a check mark in front of the Windows Media Player.
  4 restart the computer.

  Please answer back with an update.

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Jump 8 windows cursor when the finger on touchpad

  Just bought a 1015E Asus laptop.  The cursor jumps around when a finger is on the touchpad when the finger is stopped.  I tried the sensitivity setting and increase pointer is selected.  Problems continues if I change the sensitivity and if I deselect enhance pointer.  I think that it is driver related. If I take my finger on the touchpad or the finger is in the lower left or lower right click typical of the areas of the touch pad it keeps jumping around.  Thanks in advance.

  Hello

  
  
  
  
  Thanks for your posting in Microsoft Community
  
  
  Concern seems to be a hardware
  This type of isuse happens chipset and energy management and the touchpad is not properly installed or defective hardware
  Some laptops may have a button around the touchpad or an icon in the system tray that allows you to temporarily disable the touchpad.
  
  
  If you have other devices of entry as a mouse, keyboard, graphics tablet, etc., try to unplug these devices to ensure that they are not the cause of your problem.
  Make sure that your laptop has the latest Bios Update
  
  
  
  
  Please contact asus team or visit the website to download driver download above driver and install
  If the same question post here for more information
  
  
  OR TRY THIS
  
  
  1. Click Start and select Control Panel.
     
  2. Double-click the mouse control panel.
  3. Click on the large icon of the Touchpad that is in front of you.
  4. In the main menu of the Touchpad, click on the button of device selection.
  5. Place the Stick pointing to Disable radio button.
  6. Place the radio button buttons pointing to Disable.
  7. Click OK.
  8. In the main menu of the Touchpad, click the button of the Touchpad settings.
  9. Uncheck the tap click checkbox.

     Note: You can move the sliders Touchpad speed and tactility to the parameters of your choice.

  10. Click OK.
  11. In the main menu of the Touchpad, click the scroll button & Zoom parameters.
  12. Clear the check box turn on Zoom.
  13. Clear the check box enable the circular scrolling.
  14. Uncheck the enable box.
  15. Click OK.
  16. In the upper right corner of the main menu Touchpad, click the X to close the control panel.
  17. Close the Control Panel window.

• The download window appears when the file download but not display download status or maintain the list of downloads as in the past - how to restore this option?

  Formerly the download window showed the State of the download in process and retained a list of files downloaded until I deleted from the list. Now an empty download window appears automatically when I download a file. The window does not reflect the status of the download, download name, etc.. But there is no display of downloaded files. How to restore the function of the download window? I checked the option to display the download window when downloading.

  Check some settings:

  • Options > privacy > [X] do not forget the download history
    • See-> https://support.mozilla.org/en-US/kb/Options%20window%20-%20Privacy%20panel
  • When the use of clear recent history or erase automatically history when Firefox closes, do not check download history
    • See-> https://support.mozilla.org/en-US/kb/Clear%20Recent%20History

  If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.

  Not related to your question, but...

  You may need to update some plug-ins. Check your plug-ins and update if necessary:

  • Plugin check-> http://www.mozilla.org/en-US/plugincheck/
  • Adobe Shockwave for Director Netscape plug-in: install (or update) the Shockwave with Firefox plugin
  • Adobe PDF plug-in for Firefox and Netscape: Installation/update Adobe Reader in Firefox
  • Shockwave Flash (Adobe Flash or Flash): updated Flash in Firefox
  • Next-generation Java plug-in for the Mozilla browser: install or update Java in Firefox

• Restore windows files when the connection does not work

  After an accident at some point, I noticed "Restore to folder windows when connecting" did not work.

  In "Folder Options - view" it is checked.  Also, I did 'Restore Defaults' and rechecked it.

  Confirmed also with regedit it wasHKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced\PersistBrowsers set.

  Another user on the system do not have the problem.  How can this be corrected?

  Concerning

  Ray

  Raymond,

  What is the version of Windows installed on the computer?

  I wish that you perform a scan of System File Checker-

  https://support.Microsoft.com/kb/929833/en-us

  If it does not then, I would have you decant the contents of the user account to a new user account this account is possibly corrupt.

  Refer to this article-

  http://Windows.Microsoft.com/en-CA/Windows/fix-corrupted-user-profile

  Thank you.

• Update the Configuration failed on Windows Vista when the computer was closed prematurely at sea

  My son turned off the computer before the update of configuration was complete.  It uses a Compaq Vista premium desktop computer.  The operating system will not load (it is stuck in a loop trying to reconfigure the old settings before the update).  We have tried to start in Mode safe mode and do a system restore.  The first available date is November 15, when the update occurred.  System Restore got the point to finalize and then jammed (lasted at least 4 hours).   Any suggestions other than a complete system to recharge?

  Hi DRoggeman,

  Welcome to Microsoft Answers Community Forums.

  I suggest you to do the Startup Repair to fix boot of startup problem and uninstall all updates you have installed.

  Reinstall or install updates for your computer by going to http://windowsupdate.microsoft.com

  To perform the Startup Repair, you need to restart (boot) your computer using the installation disc. If you do not restart your computer from the disk, the option to repair your computer will not appear.

  1. Insert the installation disc.

  2. restart your computer.

  Click the Start button, click the arrow next to the lock button, and then click restart.

  3. If you are prompted, press any key to start Windows from the installation disc.

  Note

  If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions.

  4. choose your language settings, and then click Next.

  5. click on repair your computer.

  6. Select the operating system you want to repair, and then click Next.

  7. in the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.

  For more information, please see the links below,

  ·          http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-fix-a-boot-startup-problem Fixed a problem starting to boot.

  ·          http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions Frequently asked questions.

  Hope this information helps you.

  Kind regards

  Arona - Microsoft technical support engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.