Driver OR Sonix STR8100 D board

Similar Questions

• Driver webcam for camera on-board Pavilion dv6911om

  I reinstalled my original Vista Home Premium 32-bit using the recovery partition. All right, except that I can't make the webcam that is recognizable to the system. Therefore, I can't use my Skype video feature. When I had the factory installed OS, Skype video call worked perfectly.

  I've been everywhere on the Internet trying to find a software YouCam, Quickplay, SP37849, SP46565, SP38361 and SP 45866 - all for nothing is helping. Any software install, except Quickplay (SP38361).

  In the device, under imaging devices Manager, there is no driver webcam in the list, only my HP 6700 all-in-one printer/scanner. Is it possible that only imaging device can be installed at the same time? I really hope this isn't the case.

  Any suggestions will be appreciated. Thank you.

  Hello Futoji,

  First of all, my apologies for not answering yesterday or before. I expect an email to tell me an answer to my question.

  I spent $9 on an external camera and mic, just to have a way to "Skyping". But, I want to still try and set the built-in camera if possible.

  Not being is not a big fan of QuickkPlay, I wonder if I can install YouCam, even if my installation of the factory had QuickPlay? Something that I read during my research led me to think that this substitution can be made.

  Your suggestions have yet to be tried, but I'm going today and inform you of any success. I'm leaning towards the conclusion suggest you, that the camera may have failed.

  Thanks for your help; I'll give you an update.

  Kind regards

  Bill T

• HP DesignJet T790ps how to replace the HARD drive

  Hello

  for some reason, some time before, the problems began to appear when you start the machine. time of diagnosis revealed that the hard drive installed in the formatter Board publishes a crash.

  and at some point wonderful machine stopped running.

  tell me what to do in this case? change the map of trainer with the hard drive, or we can install the software on another drive.

  Thank you.

  I don't have the service manual for this model until this morning, so I couldn't watch manual ventilation of rooms.  There are a few models of HP where they assign a part number on the drive without having to buy the whole map trainer to get the hard drive.  The manual of the parts for this model shows B21

  CR650-67001 for just the HARD drive and the trainer card does not include the hard drive, so they separated the.  This should make less expensive repairs as long as you can tell if it's the hard drive or map of trainer at the origin of the problem.  FYI, the part number for the trainer without HARD drive card is

  CR651-67005

• RS140 cannot detect HARD drive

  Hello.

  I need advice on the LSI to Lenovo RS140 Server raid controller...
  Our company have a Lenovo RS140 server with 4 SATA HDD.

  When I boot with EasySetup DVD, it does not detect any HARD disk.
  But the BIOS detects all the HARD disk properly.

  I have updated firmware on the controller BIOS and LSI to the current version of EasyUpdate DVD, but no result...
  How to fix?

  Hello

  Since you are using a PCIe SATA RAID controller / SAS configuration setting should be AHCI.

  As seen in PIC1, you must go to the LSI WebBIOS to configure the adapter and create your virtual drive. This should allow you to install the OS.

  I guess you have the cables connecting the hard drives connected in the adapter 9240 using a mini connector SAS, correct? If you have the drives connected to the system board, the RAID controller will not be able to see them.

• Driver needed XP for Ati Radeon HD 4250 (Thinkpad Edge 14 - model 019923u)

  Hello, I have downgraded from Windows 7 to Xp and I have trouble finding the driver for the video card.

  The laptop is a Thinkpad Edge 14 - model 019923u.

  Does anyone know the correct driver for this model?

  Thank you

  Try DRIVERMAX. I had a PC that had no XP drivers. This program found and installed the drivers in XP and had it work. What it does is find a driver for this type of Board/CPU/GPU/webcam/USB card or sound.

  Here are the directions out of my head that I remember best:

  • 1 when you load first it (after it index and askes register you), place the mouse on driver downloads and information, click on start the drivermax agent.
  • 2 loading the agent to ensure that its on the 2nd tab updated. If the (part your will install) shows here then select it and then click Download. Click on the 2nd show updates for only selected updates option.
  • 3 now it will go to the site and show you the pilot/s available. I always choose the driver top list. Click the link to download next to her. Click on continue free user. Make sure that you opened with drivermax and not save on the pc.
  • 4 it will then download and let you know when it is ready to be installed. Another thing if the driver (for what your need) does not appear here, then click on the identity of unknown material below start the agent on-screen main drivermax. Then do the same to download and install it.

  There are also clips Youtube how to use DRIVERMAX. See you soon! Hope this works for you.

• When I tried to installHoyelpuzzle and Board of Directors, it was installed but that it would not complete the installation

  I installed several card games again and had no problems.  But when I tried to installHoyelpuzzle and Board of Directors, it was installed but that it would not complete the installation. I have

  Windows Explorer and uninstalled until I reinstalled it.  I've done 4 times.  He went all way through the process, than to see a message that Setup could not be resumed.  Given that the other two disks of Hoyle have been correctly installed, why do I have problems with the drive of Hoyle puzzle and board? I contacted Hoyle and does everything that they told me to do.  But without success.  What could I do it wrong?

  Hello

  (1) what is the operating system that you use on the computer?
  (2) you get error codes?
  If you use Windows 7, Hoyle Board Games is not compatible with Windows 7.
  You try to install the game in compatibility mode.
  Click on the below link to check the compatibility of the game.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/details.aspx?type=software&p=Hoyle%20Board%20Games&v=Encore&UID=&pf=0&PI=9&s=Hoyle%20card%20game&OS=64-bit
   
  You can check the link below:

  Make older programs in this version of Windows

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows
   
  You can check with the manufacturer of game for patches to run the game on Windows 7.
  http://support.Encore.com/
  I hope this helps!

• How to format drive C to load XP

  format the drive c with XP on board and hard copy of loaded XPpro

  How to do a clean install of Windows XP

  Start by changing the BIOS setting to start from the CD drive first.
  Then see below:

  Michael Steven: http://www.michaelstevenstech.com/cleanxpinstall.html
  more information: http://windowsxp.mvps.org/XPClean.htm
  and: http://www.theeldergeek.com/clean_installation_of_windows_xp.htm
  also: http://www.bootdisk.com/

  Also, make sure you have the drivers you need for your mother, video card
  card, sound card, etc.
  Try Belarc Advisor: http://www.belarc.com/free_download.html
  He did a good job of providing a wealth of information, including key software codes
  and you will need drivers for devices.

  If you perform a clean installation on an existing PC which has XP already installed:
  Check your code CD Key corresponds to what Belarc Advisor reports to your existing installation.
  Note: Windows OEM installs usually come with a sticker on the PC or laptop and may not match the installed key factory.
   
  Note: A number of vendors now supply restore CD or a restore hard disk partition
  and, usually, do not provide a Windows XP CD.

  J W Stuart: http://www.pagestart.com

• Lack of driver for ethernet controller (manufacturer: Realtek)

  I bought a hp 3330 pro MT PC with linux OS preinstalled. Just installed Winows 7 Home Basic (32 bit) Edition.

  The ethernet controller driver is missing. I tried to download a driver to install hp under my serial number of the product (sgh213t214). None of the last two drivers under driver - network solves the problem.

  The hardward device Ids are also less

  PCI\VEN_10EC & DEV_8168 & SUBSYS_17A0103C & REV_06

  PCI\VEN_10EC & DEV_8168 & SUBSYS_17A0103C

  PCI\VEN_10EC & DEV_8168 & CC_020000

  PCI\VEN_10EC & DEV_8168 & CC_0200

  I couldnot find the driver Realtek or Foxconn sites (Board machine). The sp57270.exe driver on the site Web of hp does not work either. I hope that I have haevent installed the wrong chipset driver. But only the ethernet controller icon has an exclaimation mark in the Device Manager window.

  Help would be greatly appreciated.

  Sincerely,

  Zitouni

  Hello:

  The ethernet directly from Realtek driver is functioning normally.

  Download and install the second pilot on the list...

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• Latitude D810 PATA for upgrade of the SATA HARD drive

  I have a laptop Dell Latitude D810, with an ATX hard disk controller interface (at least it is what I was told that I have, in addition the Linux kernel reports ATX so), but the installed hard drive is a Hitachi Travelstar 7 K 100 60 GB: HTS721060G9AT00, which a Ultra ATA drive with IDE interface. It connects to the motherboard with a Foxconn adaptor (p/n 59PJA). I have two questions:

  1. How can I be sure that I actually have an ATX interface for hard disks in my laptop?

  2 if I do, can I get an adapter to connect the hard drive to the ATX system board?

  
  

• Several problems with the Satellite A100-569

  Hello comrades toshers :)

  I had a portable 569 a100 in one last catalog can, last month he had to go off for repairs as the continuous screen empty and had to use the power button to shut it down and reboot again, also questions of excessive paging as well as my computer screen with a kind of mini earthquake... then it is gone and back a week and I these problems are still produce , I understand they have installed a new hard drive and a printed circuit board.

  I also noticed that I can't get the toshiba updates more about expansion memory... this laptop is not yet one year old so would appreciate any help this forum may be able to give me.

  I would sound Toshiba first thing tomorrow on the laptop being faulty, also the ease of online security does not recognize my serial number? very strange.

  long live the people

  Hello

  Obviously your laptop, one of the first models comes with the Vista operating system. To be honest, I agree with you on the RAM. 512 MB is certainly not enough. 1 GB is OK, but for me not enough. I recommend you to upgrade the RAM with 2 x 1 GB module. With 2 GB will be the laptop works well.

  The compatible RAM 1 GB module has PA3411U-2M1G part number. Use this number in Google and you'll find enough shops where you can order online.

  Good bye

• Qosmio G20 - how to find an update for the video card?

  Hi I can't find the update for the video card and when I run the game it hand me your video card drivers are too old.update them.
  my laptop:(toshiba Qosmio G20)
  My vidoe card: (NVIDIA GeForce Go 6600)
  Operating system: (Microsoft Windows XP Professional)

  Hey,.

  To be honest I don t understand your problem. Why visit nVidia?

  All you can download it from the download page of European driver from Toshiba as a boarder suggested. I even checked this and for Qosmio G20 and Windows XP you can get all the drivers no problem at all! :)

• HP probook 4520 s held the first screen of the logo

  I was installing windows when the system which took place facing upwards. When I rebooted, it crashes on the first screen of the hp logo. where written "press ESC to display the boot options. without key works ceiling light flashes several times and turn off.
  It is repeated each time. Help, please.

  When it is connected to your desktop computer, can you feel if he goes? When you say that the Bureau does not detect the hard disk, which is in the bios, or when you open my computer?  If the drive is recognized in the bios, you can buy a software like ntfs getback who will try to rebuild the fat table so you can copy items over to the hard drive of the desktop computer.  You can download a trial version that will let you know if it will work, but you will have to buy it to actually transfer the software on disk from the desktop. You can also try to download the certification test of the drive manufacturer that will fix the bad sectors and some minor problems. SpinRite will try to retrieve data for each of the areas that may be of low bits set not completely (upwards or downwards). If the Office does not see the drive in bios, the circuit board on the hard drive is bad or the disc is not rotating. If you gently hold the disc in hand and slightly turn the disc, you should feel a gyroscopic effect of the spinning drive. If you do not feel the disc spins, the motor is probably bad or racing circuit on low hard drive circuit is bad. Sometimes (perhaps 50%), you can try to replace the circuit board with the exact same model Platinum (even if you buy the same model of car, they may have different circuit boards).  The problem is that newer readers have a flash memory chip that stores the settings for each specific access accurate and speed reader. If the exact same Platinum turns the drive, but can't read well, he have to unsolder the flash chip and move it to the new circuit board. Then, the chances improve for recovery. If the new Platinum will not turn the engine, the engine is bad. You will need to send the drive to the manufacturer or to a recovery company that can remove the platters and mount them on their equipment, calibrate and read it (probably $1000 + without warranty). There are people who post how to break on the old engine and replace it with a new one, but I think it would be a mistake to try.

• Satellite Pro 4320 CD upgrade

  First of all, sorry if this message appears twice. I posted earlier this morning and he did not notice in the list of the forums then posted again.

  I myself have recently a Satellite Pro 4320, but want to upgrade the standard CD-ROM drive to a CD - RW. I found a car at a computer fair and manage mounting.

  I thought that you could drag the disc on the side and replace it - but alas no! I deleted EVERY visible screw unit and it STILL don't fall apart!

  Help! How can I change the CDROM - I have not sent it to a service provider for the lack of a second-hand car £5... I do?

  Thanks in advance

  Barry

  Hello Barry

  It is not easy to change the CD-rom on this machine and if you don't have a lot of experience you shouldn't do it yourself. Problem is that the CD is fixed on the map system and if you want to remove the drive must disconnect the System Board at first.

  To do this, you need to disassemble the whole laptop and open it by completely removing the top cover.

  Sorry but I can't give you more information because any dismantling procedure is not known to me.

  Good luck!

• Smart touch want 23: DST SHORT: 'NOT INSTALLED', SEE SMART: "DON'T INSTALL".

  start-up: HARD disk failure

  Analysis:

  (1) reboot

  (2) F2

  (3) "control of hard disk.

  (4) "quick check".

  has received: "check the hard disk starting."

  10 seconds

  has received: "ABSTRACT DST: 'NOT INSTALLED', SEE SMART: «NO INSTALLER»»

  Try to determine the root cause:

  Drive HARD or HDC/main Board?

  If anyone can help?

  After having discussed with online support, withdrawal SIMMS to force POST beeps and validate the Council Senior Planner was ok, 1st level has reached the conclusion that the HARD drive has failed.

  two options:

  1) $89 for 2 TB at best buy with local purchases

  2) $349 + shipping for 2 TB of HP support

  Option 1 was chosen.

  HP envy 23 is running on 10 to win.

• FPGA connect for compiling the server

  Hi all

  I'm just trying to write my code for my Spartan 3 FPGA. I was moved to another computer so I tried to install the right tools... LabView 2010, the module, LabView FPGA 2010 so that the pilot of the Commission of the Spartan Xlinix I use. Windows XP (32 bit)

  Everything seems functional until the moment when I try to compile the code on my device. Apparently it "impossible to connect to the build server" or "compilation tools are not installed on this computer." I thought that all that is necessary to compile is included in the download of the module.

  Is there some piece of obivous I'm missing? Thanks in advance.

  Hi Oli,

  I had the same problem recently. It is very important that all the good software and drivers are installed in the order so that everything works as expected. Looks like you have installed the driver appropriate for the Xilinx Board, you may not have Compilation of Xilinx tools for your FPGA. For the Spartan 3 FPGA, I recommend that you download Xilinx tools 12.4. This will allow your computer to compile the FPGA bitfiles for your specific FPGA module.

  Kind regards