Driver problem? N ' not load driver \SystemRoot\system32\DRIVERS\kbdhid.sys...

Recently, I get a blue screen message whenever I start my Vista Toshiba laptop. I think that the hexadecimal number is 7F with a bunch of 0, but it certainly has a 7 followed by a letter. When you use boot logging, a dozen drivers who appear to be associated with Toshiba or an AMD processor seem to be does not. So, I tried the BIOS update. Most of them disappeared accept the following:

Did not load driver \SystemRoot\System32\DRIVERS\srv.sys
Did not load driver \SystemRoot\system32\drivers\parport.sys
Did not load driver \SystemRoot\system32\DRIVERS\kbdhid.sys
Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS

Could someone tell me if any of them would cause a problem or anyone could suggest as what to do to fix my blue screen of death problem?

Hello

Have you added a hardware or drivers updated recently? Check Control Panel - Windows to see updates
If all drivers have been updated it just before what is going on has begun.

For 7f - this might be a problem of material such as uncomfortable cards or memory, while there are other causes.
Power electric low could also lead to this. Use the troubleshooters above and below, and when you get to the
pilots and segments of memory refer to my next message below and then return to the if necessary troubleshooters

If a PC remove ALL power. Opening the case, remove and reinstall all memory cards and all cables (are not
just try to squeeze) on both ends if they are accessible and on the device ends if not (remove cables and)
the relocation of their aid to eliminate minor corrosion).

If a laptop or a PC, you will need to take to a store (not BestBuy or other BigBox stores) or your system
Support from the manufacturer.

----------------------------------------------------------------------

BCCode: 7F 0x0000007F which is the same as 0x1000007F

UNEXPECTED_KERNEL_MODE_TRAP bug control has a value of 0x0000007F. This bug check indicates that the Intel CPU generated a trap and the kernel could not catch this trap.

This trap might be a bound trap (a trap the kernel is not allowed to capture) or a double foul (an error occurred during the processing of an earlier fault, which always results in a failure of the system).

Parameters

The first parameter that is displayed on the blue screen indicates the number of trap.

The most common trap codes are the following:

  • 0x00000000 or division by zero error, indicates that a DIV instruction is executed and the divisor is zero. Memory corruption, other hardware problems or software failures can cause this error.
  • 0 x 00000004, or overflow, occurs when the processor executes a call to an interrupt handler when the overflow (OF) is flag set.
  • 0x00000005, or limits check fault, indicates that the processor, then executing a BOUND instruction, determines that the operand exceeds the specified limits. A BOUND instruction ensures that a signed array index is within a certain range.
  • 0 x 00000006 or Opcode not valid, indicates that the processor attempts to execute an invalid instruction. This error occurs generally when the instruction pointer is corrupted and point to the wrong address. The most common cause of this error is hardware memory corruption.
  • 0x00000008 or Double fault, indicates that an exception occurs during a call to the previous exception handler. In general, two exceptions are handled in series. However, there are several exceptions that cannot be handled serially, and in this case, the processor signals a double fault. There are two common causes of a double fault

Cause

0x7F bug check occurs after the installation of a faulty or incompatible hardware (including memory) or if installed hardware fails.

A double fault can occur when the kernel stack overflows. This overflow occurs if multiple drivers are attached to the same battery. For example, if two file system filter drivers are associated to the same stack and then again the recursively of file system, the capacity of the battery.

Solve the problem

Troubleshooting: If you have recently added the material to the computer, remove to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. Run the diagnostics of material that does not have the system manufacturer supplies to determine which hardware component.

The scanner memory is particularly important. Faulty or incompatible memory can cause this bug check. For more information on these procedures, see the manual of your computer. Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.

If the error appears on a newly installed system, check the availability of updates for BIOS, SCSI, or card network controller. These updates are generally available on the Web site or the hardware manufacturer BBS.

Confirm that all hard drives, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.

If the error occurred after the installation of a new or updated device driver, you should remove or replace the driver. If, in this circumstance, the error occurs during the startup sequence and the system partition is formatted with NTFS, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console in order to access the file.

Also to restart your computer and press F8 to character-based menu that displays the choice of operating system. In the menu of Advanced Options , select the last known good Configuration option. This option is most effective when you add a single driver or service at a time.

Overclocking (setting of the CPU to run at a speed higher than the nominal specification) can cause this error. If you have overclocked to the computer that is experiencing the error, return the CPU to default clock speed setting.

Check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error. You can also disable caching memory BIOS to try to resolve the problem.

If you have encountered this error during the upgrade to a new version of the Windows operating system, the error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version. If possible, remove all third-party device drivers and system services and disable all antivirus before upgrade you. Contact the software manufacturer for updates of these tools. Also, make sure that you have installed the latest Windows Service Pack.

Finally, if all of the steps above do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can also cause this error.

I hope this helps.

Rob - bicycle - Mark Twain said it is good.

Tags: Windows

Similar Questions

  • stop loading at "windows\system32\drivers\crcdisk.sys".

    I lost power when running chkdisk.  Now stops at crcdisk.sys line.

    I would probably consider the first step to be to see if you can boot into safe mode.  If so, try a restore point to the pre-grant. Jay

  • Satellite A100 - c:\windows\system32\drivers\sptd.sys blue screen error

    Hello

    Hoping someone can help with this.

    I have a Toshiba A100 with Windows XP Media Center Edition 2005.

    When I try to start my computer, I get a message saying that windows did not start successfully.
    I gives me the options of:
    Safe mode
    Safe mode with networking
    Safe mode with command prompt
    Last good known Configuration
    Start Windows normally

    None of these options works. When I try Safe Mode, I get the following message:

    multi (0) disk (0) rdisk (0) partition\Windows\system32. .. .etc

    This message is repeated over and over again very fast, each time with a different .sys file at the end. Then I get this message:

    Press ESC to stop loading c:\windows\system32\drivers\sptd.sys...
    If I press ESC, I get the following blue screen:

    A problem has been detected and Windows has shut down to prevent damage to your computer.
    The problem seems to be caused by the following file: c:\windows\system32\drivers\sptd.sys
    The driver mistakenly marked a part of his image pagable instead of nonpagable.

    I don't know what except using the product recovery CD and fitness in shape, but I can't afford to lose some of the data on my computer, and this would erase everything.

    Has anyone had experience with this? Any advice?

    It would be much appreciated.

    Hello

    Seems the OS or the partition where the operating system has been installed, is corrupted.
    I don't know why this happened, but there are different reasons for this

    In any case, I think that you have no choice as to reinstall the OS using the recovery disk.

    You want to get access to the data on the HARD drive?
    Well, you could remove the laptop HARD drive and it could connect as an external USB device to another computer. Then, you should try to copy the data to another HARD disk.

    Who could help

  • Not able to install Bullguard internet security, it requires "c:\windows\system32\drivers\afw.sys" agnitum firewall driver file, how can I find?

    Original title: file "c:\windows\system32\drivers\afw.sys" agnitum firewall driver, how to find it.

    I downloaded a trial version of Bullguard internet security and while downloading stopped at one point and ask for the file above. I tried a nd produce no result. Any ideas please. Thanks, pete

    C:\windows\system32\drivers\afw.sys with description Agnitum Firewall NDIS Driver is a driver file of Agnitum Ltd. belonging to Outpost Firewall product.

    The file is digitally signed Agnitum Ltd. - VeriSign Time Stamping Services signatory - G2

    We do not recommend remove digitally signed files from Agnitum Ltd.

    Chk this link

    http://www.OutpostFirewall.com/Forum/showthread.php?22526-missing-Afw-sys

    Replace the file from another computer and check.

    try to download it from this link

    http://sysfilesdownload.com/A/Afw.sys.html

  • Satellite L500D - Iinitially had a problem "could not load the profile.

    Satellite L500D initially had a problem 'could not load profile' then stop. It is now the windows installation discs that I don't have. Where can I get them? They can be downloaded from Microsoft or Toshiba sites?

    Error message:
    File: \boot\BCD
    Status: OxcOOOOOOf
    Info: an error occurred while trying to enter the boot configuration data

    ANY HELP WILL BE GREATLY APPRECIATED THANKS

    Hey Buddy,

    > They can be downloaded from Microsoft or Toshiba sites?
    No, the disc can t be downloaded because it s not for free.

    You can start in safe mode?

    In the worst case operating system is confusing to the top and you have to reinstall Windows, but so you can take the Toshiba Recovery disk that will restore your notebook back to factory with all the drivers and tools of Toshiba.

  • Once I turned on the computer I got the following message: Windows could not start because the following file is missing or damaged. System32\Drivers\Ntfs.sys

    I just download Microsoft Office 2010 Professional and then turns off the computer with XP operating system. Once I turned on the computer I got the following message:

    Windows could not start because the following file is missing or damaged;

    System32\Drivers\Ntfs.sys

    You can try to repair this file by starting Windows Setup using the original Setup CD

    Select 'r' in the first screen to start repair.

    Then, I started the computer with the Original installation CD and press 'r' by following the instructions. Then, I received this message:

    1: C:\WINDOWS

    Which Windows installation you want to connect?

    (to cancel, press enter)

    What do I put here?

    You must first start on doing something so USB drive a bootable Hiren.

    Here's how:

    I'll recommend you use Hiren boot CD (it will go also to a flash/USB stick/USB).

    It's good for you, because there a lot of tools more on that on the Recovery Console CD of XP, doesn't your administrator passwords and you will not have to futz round in your BIOS, if any afflicted system has SATA drives - Hiren can deal with this.

    You will have a bunch of great tools that you have in XP... Recovery Console an editor of the register, adjustable password and an office that resembles Windows XP so you will feel comfortable flexibility.

    You can easily copy your personal data (documents, pictures, music) to an external drive.

    A system of work, start by downloading the latest version on Hiren Boot CD from here (it is a substantial download but worth it):
    http://www.hirensbootcd.org/download/    (look to the bottom of the page).

    Unzip the Hiren to a folder where you can find it.  There's a Hiren. BootCD.15.x.iso that you have to then.

    Hiren was instructed to make a bootable USB drive that you can use, but it takes you first burn the .iso to a CD image file and a few other measures, so I suggest another way and here's how:

    Download RUFUS 1.3.2 or whatever the latest version is here (read a few things on the page so you can learn more on this subject):

    http://Rufus.AKEO.IE/

    I will warn to be careful that don't accidentally format you a hard disk - don't forget your USB key is in and know what the drive letter!  This part makes me still a little nervous, so be careful.

    Launch of RUFUS and all default values should be fine for the device, choose letter of your USB drive, quick tag format FAT32, it if you want and in the Format options box, click on the little icon that looks like a CD and a window will open.  Navigate through this dialogue to point to the folder that contains the Hiren. BootCD.15.x.iso that you have unpacked above and the box should change to say the image ISO (RUFUS includes the Hiren ISO file).

    Double check you have the right device selected in the top (NOT you HDD) click Start, acknowledge receipt of the warning and let it finish (it will take a little time) it copies the files.   Hiren ISO is also a good size.

    When RUFUS is finished, it will say "DONE" at the bottom.

    Put the USB in the afflicted machine and reset/reboot and regardless of the button you press to get a boot menu where you can select the USB drive as first boot device (it's F11 for me).  If you do not see a start menu choice, you will need to set your BIOS to boot from USB first instead of the HARD disk.

    When the Hiren menu displays, choose the XP Mode of Mini and it will start loading (slowly from a USB key) and finally, you should see a windowsy looking for office.  You should recognize the part and feel uncomfortable, but it is not your office - the office of the Hiren!

    Remember: you do not start on your hard drive, - you started in the Office of the Hiren.

    A way to check the drive for errors is to open my computer and right-click on your afflicted player and choose Properties, tools, error, check checking now... put a check mark in the boxes and then start.

    Sometimes that works, then you can also click on start, run and in the type box:

    cmd

    Click OK to open a command prompt window and enter the following command (assuming that XP is installed on your C drive)

    CHKDSK c: /r

    This disk check can last a long time (perhaps several to several hours) depending on the size of the volume, the amount of data on the volume and what the disk check finds to do.  You may need to run more than once.

  • Error - EPPkt.sys and c:\windows\system32\drivers\afw.sys not found and fix crashes in Windows XP Pro computer.

    Original title: during repair XP Pro from the disk installation, everything crashes.

    I am writing this plea on my desktop, pc Win 7 it. The pc is older and elsewhere in the House.

    Due to the white/white space in Add/Remove Programs, after checking the extent of possible for viruses, corruption Reg, etc., the advice of consensus was to reinstall the Windows, using the disc (this XP Pro was on the HARD drive when I got the pc - new to 2009 - and I did the back-up recommended/controlled , and that's what I was doing Rcounter Set up, around 1700 BST.

    Everything seemed to go OK, but black screen of Windows is now the small hourglass circulating and 'Please wait '.  The HARD drive is flickering, but it's been more than 3 hours!

    My second pc was rotten, and I had to reinstall or repair XP Home [disk] a few times. It is only 35 GB, compared to more than 100 on the pc in question - but I've never met before delay.

    Installation messages were as follows:

    EPPkt.sys and c:\windows\system32\drivers\afw.sys not found.  I checked this point, and it should not have caused any problems. It has also sought a labeled disc 'Machine Virtual Network Services', which no doubt, since I did not, was never necessary.

    I'll leave it on - but...

    Help, please!

    Well, I had to bow to the inevitable. Please accept this response as a ' I've been there - it could happen to you. "

    I spoke to BT [they provide my broadband] and the helpful guy asked me to look at the installation and reinstall in a different place. It's OK, but [, BUT] some of the drivers have been zapped in eternity. PCI, sounds, videos. The guy thought BT that these had been modified or replaced since the beginning, whereas they were not available. The XP Prof is on the pc when I got it, but I assumed that the pilots were on the backup disk, I did. No, they were not. And how to go online to search for them if we could not put in place the ethernet connection?
    So, I bought Win - 7 it 32-bit full ed. [be too afraid to try an upgrade].

    It could have been a response in the migration of these from other drivers, but I guess it was time to go.

    As I can't afford to buy new COREL, MS Word, etc, I have installed free VMWare player as a host for my older progs in a virtual environment.

    Another thing came out of this: although what remained of XP has been saved by 7 as WINDOWS.old, I am very happy that I had a HDD eternal with ntfs to preserve my files and installable 3rd party progs.

    I hope this might help someone - thanks for the info.

  • Sony VGN - NR160E Ultimate laptop. w / Windows 7 Ultimate, failed to load because the c:\windows\system32\drivers\elxstor.sys of the 5.2.10.211 file is corrupted or missing

    I have a laptop VGN-NR160E Sony with an Intel Core 2 Duo T5250 / 1.5 GHz with Vista OEM. It has been upgraded to Windows 7 Ultimate. The former owner has not only any disk, therefore, or I'm doing. I have after I tried to update and got an error this system failed to load because the c:\windows\system32\drivers\elxstor.sys of 5.2.10.211, the file is damaged or missing, I tried all the computer in repair and drives the ISO of Windows 7 options, I need help by someone much more intelligent and savvy than me in computer science.

    You have a pirated copy of Windows 7 Ultimate on your system. You must install a genuine copy.

  • Computer stops loading on WINDOWS\system32\drivers\crcdisk.sysrepair

    original title: WINDOWS\system32\drivers\crcdisk.sysrepair

    my laptop computer on windows\system32\drivers\crcdisk.sys stop

    Hello ernestoResto,

    You should try running a Chkdsk on your computer to check if there are bad sectors on the hard disk.

    a. Insert the Windows Vista DVD into the DVD drive, and then restart your computer from the DVD.

    N1ote: when you get the press quickly press any key to boot from the CD or DVD, press any key on the keyboard to restart your computer by using the Windows Vista DVD.

    b. Select your language setting, and then click Next.

    c. Select repair your computer.

    d. Select the installation of Windows Vista to be repaired, and then click Next.

    e. under System Recovery Options, select command prompt and type:

    CHKDSK [drive:] [/ p] | [/ r]

    [drive:] Specifies the drive to check.

    / p check even if the drive is not marked dirty, bad.

    /r locates bad sectors and recovers readable information (implies / p).

    WARNING: This could cause loss of data on your computer. It is recommended that you back up all data and files before performing this.

    Thank you
    Irfan H, Engineer Support Microsoft Answers.

  • file: \windows\system32\drivers\sptd.sys status: 0 x 0000001 Info: windows failed to load because a system critics driveris missing or corrupt.

    Good evening

    Windows no longer starts.

    at startup, it tells me:
    Windows Boot Manager
     
    file: \windows\system32\drivers\sptd.sys
         
    status: 0 x 0000001
     
    Info: windows could not load because a system critics driveris missing or corrupt.
    PS: my pc is an Acer aspire 7738G and vista under works

    French

    Please click on the icon of language at the bottom of this page to select your language from the list of countries / regions to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the language there, the support options for additional international sites are at the link below:

    http://support.Microsoft.com/common/international.aspx

    Please click the language icon at the bottom of this page to select your language from the list of countries / regions pour post your question in the language of your choice. The forum you posted is fr English only. If you can't find the language here, additional support options to international destinations can be found by following the link below:

    http://support.Microsoft.com/common/international.aspx

    Thank you.

  • \windows\system32\drivers\spldr.sys my computer does not start beyond the Boot Manager, HELP!

    \windows\system32\drivers\spldr.sys

    Hello Jayates18,

    Take a look at this link to repair your boot problem. I hope this help you. Make it a great day!

    Link: http://support.microsoft.com/kb/927392/

    "In the end, the love you take, is equal to the Love You Make"

  • My cdrom is not available because system32\drivers\cdrom.sys is damaged.

    My cdrom is not available because system32\drivers\cdrom.sys is damaged.

    http://social.technet.Microsoft.com/forums/en/w7itprohardware/thread/9e694df5-05cf-4C89-b7d2-7ca138e55a90

  • system32\DRIVERS\pci.sys missing or corrupt file error but windows xp is already preloaded on computer when purchased

    missing or corrupt file error system32\DRIVERS\pci.sys keeps appearing. I had a problem with google chrome and then stop everything. This error appeared. It tells me to use the cr rom boot but xp was already loaded on the sony vaio that we bought a few years ago. I don't know what to do next because I don't want to lose the pictures and music, we have on the hard drive. Any help would be appreciated

    If your data is not backed up, then at some point that the data will be lost.

    Your Sony are delivered with a hidden restore partition or recovery disks, but I do not think that the Sony recovery allows to repair an installation of win, only pure install.

    You must remove the drive and it slave on another PC in order to retrieve the data, or take it to a decent repair shop for them to do it for you

  • BSOD, c:\windows\system32\drivers\mrxdav.sys error?

    I am a veterinary technician, not a computer tech, so I'm out of my depth on this and need help, because these computers are essential for the work I do.

    I work with two laptops, Dell Latitude D600 (I know, I know - they're old.) New ones have been approved as soon as budget free of the order).  Specifications are the following:

    1.60 Ghz processor; 27 GB hard drive; 599 Mhz, 256 MB of RAM, running Windows XP Pro w/Service Pk 3

    We use one of the cell phones as our main unit and the other is our backup.  About 3 weeks, our main unit suddenly came with the BSOD on boot-up top, with the following error message:

    C:\windows\system32\drivers\mrxdav.sys

    The driver unloaded without cancelling pending operations.

    We had not added anything to the extent of the software or hardware is concerned and had not changed anything except for the addition of new text files through an application that we run.  A opted for our backup laptop and who ran very well for the last few weeks, but now we get the same BSOD and error on this unit as well.  I was able to get the machine backup at startup and function normally after about 100 restarts the other day, and he ran all day with no problems once that it loaded everything.

    How do we get this straightened out? We do not have a computer scientist - just a couple of people who know a little more to turn on a computer/turn off.  I ran a clean-up/management application (I-Obit AdvancedCare) for cleaning the registry errors, etc., but that has not solved the problem.

    The error message indicates an infection, but because you have scanned, it is more likely that the portable master knows hardware problems and/or the operating system is corrupt. If you are Imaging for the second laptop, that explains why you see the same questions about this. Best free now part of budget money.

    http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

    Start with the RAM and then make the hard drive.

    If good test material, back up your data if necessary and do a clean install of Windows.

    MS - MVP - Elephant Boy computers - don't panic!

  • Vista saying, missing/corrupted, \windows\system32\drivers\oduzt.sys

    Hey guys, I have more solutions for the time and thought that I have turned to a group instead of address on mine.

    When the problem started?

    This morning, so a few hours there.

    What have you tried to fix it?

    Restore Vista CD

    What is the error message (all)?

    Says, the file: \Windows\System32\Drivers\oduzt.sys
    Situation: 0xc0000225
    Info: Windows could not load a critical system driver is missing or corrupt

    I've never heard of this file...

    What was the last thing you did before the problem started?

    Tried to delete/remove virus and malware
    Malwarebytes
    used, Microsoft's malicious remover<-- from="" microsoft="">
    the Microsoft file was the last thing I used before that happened.
    literally on reboot has happened.

    What are your system specs?
    Vista sp1 home
    Laptop Gateway
    Guessing 32bits
    Model no: MA7
    Model mt6840
    I'll tell you more if I could pull up? I can access the recovery cd cmd there at - it a command that will show?

    Do you have a screenshot?
    a little... haha taken with a camera...

    Also I was wondering... is there a way I can run a partition to say windows XP and take all the files off your computer and save them.

    then if it comes down to it, I can just empty the computer and install vista?

    Hello

    You can back up your data is to put the drive in another computer as a 2nd car or
    in an external USB enclosure. Both methods would allow you to save the data in removable
    readers of media such as CD, DVD or USB.

    Sounds like malware: (see message using startup so you can't run Safe Mode).

    If you need search malware here's my recommendations - they will allow you to
    scrutiny and the withdrawal without ending up with a load of spyware programs running
    resident who can cause as many questions as the malware and may be more difficult to detect as the
    cause.

    No one program cannot be used to detect and remove any malware. Added that often easy
    to detect malicious software often comes with a much harder to detect and remove the payload. Then
    its best to be thorough than paying the high price later now too. Check with them to one
    extreme overkill point and then run the cleaning only when you are sure that the system is clean.

    It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
    the regular windows when you can.

    Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
    (If Rootkits run UnHackMe)

    Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

    Malwarebytes - free
    http://www.Malwarebytes.org/

    Run the malware removal tool from Microsoft

    Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

    You should get this tool and its updates via Windows updates - if necessary, you can
    Download it here.

    Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
    (Then run MRT as shown above.)

    Microsoft Malicious - 32-bit removal tool
    http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

    Microsoft Malicious removal tool - 64 bit
    http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

    also install Prevx to be sure that it is all gone.

    Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

    Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
    security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
    here or use Google to see how to remove.
    http://www.prevx.com/   <-->
    http://info.prevx.com/downloadcsi.asp  <-->

    Choice of PCmag editor - Prevx-
    http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

    Try the demo version of Hitman Pro:

    Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
    (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
    what you have done (such as antivirus, firewall, etc.).
    http://www.SurfRight.nl/en/hitmanpro

    --------------------------------------------------------

    If necessary here are some free online scanners to help the

    http://www.eset.com/onlinescan/

    New Vista and Windows 7 version
    http://OneCare.live.com/site/en-us/Center/whatsnew.htm

    Original version
    http://OneCare.live.com/site/en-us/default.htm

    http://www.Kaspersky.com/virusscanner

    Other tests free online
    http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

    --------------------------------------------------------

    Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
    system files.

    Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

    Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
    RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker
    (SFC.exe) program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -----------------------------------------------------------------------

    If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

    http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

Maybe you are looking for

  • Text messaging to twinkle in MacOS Sierra overview

    Whenever I have access to a mailbox Mail Mac, preview all messages text flickers at the start, then stops.  It is a new show since the upgrade to Sierra.  I have not seen this reported by someone else, so I hope it's something that can be solved.  Is

  • iTunes connection problems

    I can't connect to iTunes is a matter of course on?

  • Coupon printer plugin causes refreshing constantly

    some sites Web IE... torrentfreak.com, sometimes ebay.com and GMXmail.com refresh constantly. I have disabled every add-on and extension until the issue was resolved and found that when the coupon Manager is disabled, the problem is solved, but I can

  • Make the disk image using disk utility and the message "Apple_HFS: 0" is displayed

    I'm doing a disk image to try to work on that later. This is an image of a failed disk drive. Some areas can only be read, I know and the process takes a long time because of this, so I'm willing to be patient. I get messages in the disk utility wind

  • Oddity with Active Directory?

    Hello I have problems with the AD.  My environment is a hybrid of Server 2003 in place with several domain controllers.  Whats happening is when a user, regardless of the PC operating system, will open a file on a share on the network, it is impossib