My cdrom is not available because system32\drivers\cdrom.sys is damaged.

Similar Questions

• Windows didn't start because System32\Drivers\Ntfs.sys is missing

  Windows did not start because System32\Drivers\Ntfs.sys is missing or damaged.

  In fact, I tried the Installation Windows XP Home with the Recovery DVD - ROM product.

  After formatting it says: out of dvd, then press ctrl_alt_del

  Then appears the error with a missing or damaged file. (infact in German, because I install in German)

  Hello

  I studied a bit in the web and the question could be a malfunction of the memory module. I recommend checking out the RAM modules.

• Once I turned on the computer I got the following message: Windows could not start because the following file is missing or damaged. System32\Drivers\Ntfs.sys

  I just download Microsoft Office 2010 Professional and then turns off the computer with XP operating system. Once I turned on the computer I got the following message:

  Windows could not start because the following file is missing or damaged;

  System32\Drivers\Ntfs.sys

  You can try to repair this file by starting Windows Setup using the original Setup CD

  Select 'r' in the first screen to start repair.

  Then, I started the computer with the Original installation CD and press 'r' by following the instructions. Then, I received this message:

  1: C:\WINDOWS

  Which Windows installation you want to connect?

  (to cancel, press enter)

  What do I put here?

  You must first start on doing something so USB drive a bootable Hiren.

  Here's how:

  I'll recommend you use Hiren boot CD (it will go also to a flash/USB stick/USB).

  It's good for you, because there a lot of tools more on that on the Recovery Console CD of XP, doesn't your administrator passwords and you will not have to futz round in your BIOS, if any afflicted system has SATA drives - Hiren can deal with this.

  You will have a bunch of great tools that you have in XP... Recovery Console an editor of the register, adjustable password and an office that resembles Windows XP so you will feel comfortable flexibility.

  You can easily copy your personal data (documents, pictures, music) to an external drive.

  A system of work, start by downloading the latest version on Hiren Boot CD from here (it is a substantial download but worth it):
  http://www.hirensbootcd.org/download/    (look to the bottom of the page).

  Unzip the Hiren to a folder where you can find it.  There's a Hiren. BootCD.15.x.iso that you have to then.

  Hiren was instructed to make a bootable USB drive that you can use, but it takes you first burn the .iso to a CD image file and a few other measures, so I suggest another way and here's how:

  Download RUFUS 1.3.2 or whatever the latest version is here (read a few things on the page so you can learn more on this subject):

  http://Rufus.AKEO.IE/

  I will warn to be careful that don't accidentally format you a hard disk - don't forget your USB key is in and know what the drive letter!  This part makes me still a little nervous, so be careful.

  Launch of RUFUS and all default values should be fine for the device, choose letter of your USB drive, quick tag format FAT32, it if you want and in the Format options box, click on the little icon that looks like a CD and a window will open.  Navigate through this dialogue to point to the folder that contains the Hiren. BootCD.15.x.iso that you have unpacked above and the box should change to say the image ISO (RUFUS includes the Hiren ISO file).

  Double check you have the right device selected in the top (NOT you HDD) click Start, acknowledge receipt of the warning and let it finish (it will take a little time) it copies the files.   Hiren ISO is also a good size.

  When RUFUS is finished, it will say "DONE" at the bottom.

  Put the USB in the afflicted machine and reset/reboot and regardless of the button you press to get a boot menu where you can select the USB drive as first boot device (it's F11 for me).  If you do not see a start menu choice, you will need to set your BIOS to boot from USB first instead of the HARD disk.

  When the Hiren menu displays, choose the XP Mode of Mini and it will start loading (slowly from a USB key) and finally, you should see a windowsy looking for office.  You should recognize the part and feel uncomfortable, but it is not your office - the office of the Hiren!

  Remember: you do not start on your hard drive, - you started in the Office of the Hiren.

  A way to check the drive for errors is to open my computer and right-click on your afflicted player and choose Properties, tools, error, check checking now... put a check mark in the boxes and then start.

  Sometimes that works, then you can also click on start, run and in the type box:

  cmd

  Click OK to open a command prompt window and enter the following command (assuming that XP is installed on your C drive)

  CHKDSK c: /r

  This disk check can last a long time (perhaps several to several hours) depending on the size of the volume, the amount of data on the volume and what the disk check finds to do.  You may need to run more than once.

• Error - EPPkt.sys and c:\windows\system32\drivers\afw.sys not found and fix crashes in Windows XP Pro computer.

  Original title: during repair XP Pro from the disk installation, everything crashes.

  I am writing this plea on my desktop, pc Win 7 it. The pc is older and elsewhere in the House.

  Due to the white/white space in Add/Remove Programs, after checking the extent of possible for viruses, corruption Reg, etc., the advice of consensus was to reinstall the Windows, using the disc (this XP Pro was on the HARD drive when I got the pc - new to 2009 - and I did the back-up recommended/controlled , and that's what I was doing Rcounter Set up, around 1700 BST.

  Everything seemed to go OK, but black screen of Windows is now the small hourglass circulating and 'Please wait '.  The HARD drive is flickering, but it's been more than 3 hours!

  My second pc was rotten, and I had to reinstall or repair XP Home [disk] a few times. It is only 35 GB, compared to more than 100 on the pc in question - but I've never met before delay.

  Installation messages were as follows:

  EPPkt.sys and c:\windows\system32\drivers\afw.sys not found.  I checked this point, and it should not have caused any problems. It has also sought a labeled disc 'Machine Virtual Network Services', which no doubt, since I did not, was never necessary.

  I'll leave it on - but...

  Help, please!

  Well, I had to bow to the inevitable. Please accept this response as a ' I've been there - it could happen to you. "

  I spoke to BT [they provide my broadband] and the helpful guy asked me to look at the installation and reinstall in a different place. It's OK, but [, BUT] some of the drivers have been zapped in eternity. PCI, sounds, videos. The guy thought BT that these had been modified or replaced since the beginning, whereas they were not available. The XP Prof is on the pc when I got it, but I assumed that the pilots were on the backup disk, I did. No, they were not. And how to go online to search for them if we could not put in place the ethernet connection?
  So, I bought Win - 7 it 32-bit full ed. [be too afraid to try an upgrade].

  It could have been a response in the migration of these from other drivers, but I guess it was time to go.

  As I can't afford to buy new COREL, MS Word, etc, I have installed free VMWare player as a host for my older progs in a virtual environment.

  Another thing came out of this: although what remained of XP has been saved by 7 as WINDOWS.old, I am very happy that I had a HDD eternal with ntfs to preserve my files and installable 3rd party progs.

  I hope this might help someone - thanks for the info.

• file: \windows\system32\drivers\sptd.sys status: 0 x 0000001 Info: windows failed to load because a system critics driveris missing or corrupt.

  Good evening

  Windows no longer starts.

  at startup, it tells me:

  Windows Boot Manager

   

  file: \windows\system32\drivers\sptd.sys

       

  status: 0 x 0000001

   

  Info: windows could not load because a system critics driveris missing or corrupt.
  PS: my pc is an Acer aspire 7738G and vista under works

  French

  Please click on the icon of language at the bottom of this page to select your language from the list of countries / regions to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the language there, the support options for additional international sites are at the link below:

  http://support.Microsoft.com/common/international.aspx

  Please click the language icon at the bottom of this page to select your language from the list of countries / regions pour post your question in the language of your choice. The forum you posted is fr English only. If you can't find the language here, additional support options to international destinations can be found by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Thank you.

• Driver problem? N ' not load driver \SystemRoot\system32\DRIVERS\kbdhid.sys...

  Recently, I get a blue screen message whenever I start my Vista Toshiba laptop. I think that the hexadecimal number is 7F with a bunch of 0, but it certainly has a 7 followed by a letter. When you use boot logging, a dozen drivers who appear to be associated with Toshiba or an AMD processor seem to be does not. So, I tried the BIOS update. Most of them disappeared accept the following:

  Did not load driver \SystemRoot\System32\DRIVERS\srv.sys
  Did not load driver \SystemRoot\system32\drivers\parport.sys
  Did not load driver \SystemRoot\system32\DRIVERS\kbdhid.sys
  Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS

  Could someone tell me if any of them would cause a problem or anyone could suggest as what to do to fix my blue screen of death problem?

  Hello

  Have you added a hardware or drivers updated recently? Check Control Panel - Windows to see updates
  If all drivers have been updated it just before what is going on has begun.

  For 7f - this might be a problem of material such as uncomfortable cards or memory, while there are other causes.
  Power electric low could also lead to this. Use the troubleshooters above and below, and when you get to the
  pilots and segments of memory refer to my next message below and then return to the if necessary troubleshooters

  If a PC remove ALL power. Opening the case, remove and reinstall all memory cards and all cables (are not
  just try to squeeze) on both ends if they are accessible and on the device ends if not (remove cables and)
  the relocation of their aid to eliminate minor corrosion).

  If a laptop or a PC, you will need to take to a store (not BestBuy or other BigBox stores) or your system
  Support from the manufacturer.

  ----------------------------------------------------------------------

  BCCode: 7F 0x0000007F which is the same as 0x1000007F

  UNEXPECTED_KERNEL_MODE_TRAP bug control has a value of 0x0000007F. This bug check indicates that the Intel CPU generated a trap and the kernel could not catch this trap.

  This trap might be a bound trap (a trap the kernel is not allowed to capture) or a double foul (an error occurred during the processing of an earlier fault, which always results in a failure of the system).

  Parameters

  The first parameter that is displayed on the blue screen indicates the number of trap.

  The most common trap codes are the following:

  • 0x00000000 or division by zero error, indicates that a DIV instruction is executed and the divisor is zero. Memory corruption, other hardware problems or software failures can cause this error.
  • 0 x 00000004, or overflow, occurs when the processor executes a call to an interrupt handler when the overflow (OF) is flag set.
  • 0x00000005, or limits check fault, indicates that the processor, then executing a BOUND instruction, determines that the operand exceeds the specified limits. A BOUND instruction ensures that a signed array index is within a certain range.
  • 0 x 00000006 or Opcode not valid, indicates that the processor attempts to execute an invalid instruction. This error occurs generally when the instruction pointer is corrupted and point to the wrong address. The most common cause of this error is hardware memory corruption.
  • 0x00000008 or Double fault, indicates that an exception occurs during a call to the previous exception handler. In general, two exceptions are handled in series. However, there are several exceptions that cannot be handled serially, and in this case, the processor signals a double fault. There are two common causes of a double fault

  Cause

  0x7F bug check occurs after the installation of a faulty or incompatible hardware (including memory) or if installed hardware fails.

  A double fault can occur when the kernel stack overflows. This overflow occurs if multiple drivers are attached to the same battery. For example, if two file system filter drivers are associated to the same stack and then again the recursively of file system, the capacity of the battery.

  Solve the problem

  Troubleshooting: If you have recently added the material to the computer, remove to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. Run the diagnostics of material that does not have the system manufacturer supplies to determine which hardware component.

  The scanner memory is particularly important. Faulty or incompatible memory can cause this bug check. For more information on these procedures, see the manual of your computer. Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.

  If the error appears on a newly installed system, check the availability of updates for BIOS, SCSI, or card network controller. These updates are generally available on the Web site or the hardware manufacturer BBS.

  Confirm that all hard drives, hard disk controllers and SCSI adapters are listed in the list of the products tested Microsoft Windows market.

  If the error occurred after the installation of a new or updated device driver, you should remove or replace the driver. If, in this circumstance, the error occurs during the startup sequence and the system partition is formatted with NTFS, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console in order to access the file.

  Also to restart your computer and press F8 to character-based menu that displays the choice of operating system. In the menu of Advanced Options , select the last known good Configuration option. This option is most effective when you add a single driver or service at a time.

  Overclocking (setting of the CPU to run at a speed higher than the nominal specification) can cause this error. If you have overclocked to the computer that is experiencing the error, return the CPU to default clock speed setting.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver that generated the error. You can also disable caching memory BIOS to try to resolve the problem.

  If you have encountered this error during the upgrade to a new version of the Windows operating system, the error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version. If possible, remove all third-party device drivers and system services and disable all antivirus before upgrade you. Contact the software manufacturer for updates of these tools. Also, make sure that you have installed the latest Windows Service Pack.

  Finally, if all of the steps above do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can also cause this error.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Sony VGN - NR160E Ultimate laptop. w / Windows 7 Ultimate, failed to load because the c:\windows\system32\drivers\elxstor.sys of the 5.2.10.211 file is corrupted or missing

  I have a laptop VGN-NR160E Sony with an Intel Core 2 Duo T5250 / 1.5 GHz with Vista OEM. It has been upgraded to Windows 7 Ultimate. The former owner has not only any disk, therefore, or I'm doing. I have after I tried to update and got an error this system failed to load because the c:\windows\system32\drivers\elxstor.sys of 5.2.10.211, the file is damaged or missing, I tried all the computer in repair and drives the ISO of Windows 7 options, I need help by someone much more intelligent and savvy than me in computer science.

  You have a pirated copy of Windows 7 Ultimate on your system. You must install a genuine copy.

• Error code 797: connection is not available because there is a problem with your network card or modem

  I have a Windows 7 laptop. I use broadband (DSL) to connect to the internet. Lately, I have an error with the code 797. It says connection is not available because there is a problem with your modem or network card. I have a Sony Vaio e series laptop.

  Hi Muffakham,

  Thanks for posting your question in the Microsoft Community forums.

  I see from the description of the problem that you are unable to connect to the Internet and receive "Error Code 797 connection is not available because there is a problem with your network card or modem".

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

  To provide the proper resolution, that I would need more information on your side.
  Did you the latest changes on the computer before this problem?

  This problem may occur because of damaged or incompatible, drivers connection settings incorrect network, hardware or software problems and missing updates.

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  Method 2:
  If the problem is not resolved, I suggest you try the procedure described in the article and see if it helps.

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check out the link for more information.

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know the status of the issue after you perform the troubleshooting steps. If you need information about the problem with the connection to the Internet or get help, I'll be happy to help you. We, at tender Microsoft to excellence.

• Camera is not available because the SD card is mounted on a PC. Unplug the USB cable to move forward.

  I tried to download pictures from my phone.  She does not quite sure why, but the main problem is I can't access my camera or the photos on my phone now.  I get messages like this:- camera is not available because the SD card is mounted on a PC.  Unplug the USB cable from proceed.  I have tried several things and finally just manually disconnected the cable, but not luck. and now also message as follows:- your content is not available because your phone is used as a USB storage device.   Disconnect the USB to access your content.  Would appreciate help!

  Hello

  1. What is the brand and model of the phone?

  2. have you been able to access (or discovered) files on the computer?

  3. what error do you get when you try to copy files to the computer?

  4 you did changes to the computer, before the show?

  Method 1:

  Check out the following link.

  Tips for solving problems of USB devices

  Method 2:

  Connect the phone to another computer and check.

  Method 3:

  Check if the phone includes settings to disable the USB connection.

• Not able to install Bullguard internet security, it requires "c:\windows\system32\drivers\afw.sys" agnitum firewall driver file, how can I find?

  Original title: file "c:\windows\system32\drivers\afw.sys" agnitum firewall driver, how to find it.

  I downloaded a trial version of Bullguard internet security and while downloading stopped at one point and ask for the file above. I tried a nd produce no result. Any ideas please. Thanks, pete

  C:\windows\system32\drivers\afw.sys with description Agnitum Firewall NDIS Driver is a driver file of Agnitum Ltd. belonging to Outpost Firewall product.

  The file is digitally signed Agnitum Ltd. - VeriSign Time Stamping Services signatory - G2

  We do not recommend remove digitally signed files from Agnitum Ltd.

  Chk this link

  http://www.OutpostFirewall.com/Forum/showthread.php?22526-missing-Afw-sys

  Replace the file from another computer and check.

  try to download it from this link

  http://sysfilesdownload.com/A/Afw.sys.html

• Cannot connect to the local file and print when the domain controller is not available because the network connection

  Hi all
  Having problems for local users, connection to a file and print server in one of my satellite offices.
  When my t1 connection is disrupted (problem of local carrier) my users when the connection is down to connect to the file room and print and always have access to their files and the local printer.
  The domain controller is off site in my main office.
  Environment:
  All local desktop clients are windows machines 7.
  Printing and local file is a windows 2003 server.
  DC is window 2008
  Note that we recently changed all 2003 to all domain controllers the PDC 2008, suspect that it may cause the problem, but just cannot know where it track.
  Any help or thoughts would be appreciated.
  Thank you

  Hello trj'hwma,

  Thank you for the question!

  It's discouraging to know that have problems you with the local file and print. As I understand well you cannot connect to the local file and print when the domain controller is not available because the network connection.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums. You can follow the link to your question:

  Windows 7 IT Pro category

  Answer to us if you have problems with the local files and print or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• < error > < security > < BEA-000000 > < validation events is not available because no JMS Transport is available. The remote L2 caches will be out of sync. >

  I'm trying to set up a cluster, I installed my SQL server DB and Weblogic Portal 10.3.2 on two different machines and each thing is correctly configured according to my knowledge.

  but when I am trying to start my node managed on a remote machine, out of sync error continually as shown below

  < 6 sep, 2014 16:42:02 IST > < error > < security > < BEA-000000 > < validation events is not available because no JMS Transport is available. The remote L2 caches will be out of sync >

  < 6 sep, 2014 16:42:07 IST > < error > < security > < BEA-000000 > < validation events is not available because no JMS Transport is available. The remote L2 caches will be out of sync >

  < 6 sep, 2014 16:42:13 IST > < error > < security > < BEA-000000 > < validation events is not available because no JMS Transport is available. The remote L2 caches will be out of sync >

  < 6 sep, 2014 16:42:18 IST > < error > < security > < BEA-000000 > < validation events is not available because no JMS Transport is available. The remote L2 caches will be out of sync >

  < 6 sep, 2014 16:42:24 IST > < error > < security > < BEA-000000 > < validation events is not available because no JMS Transport is available. The remote L2 caches will be out of sync >

  NOTE: I can connect to my DB using java utils.dbping [MSSQLSERVER4 |] MSSQLSERVERB] < db username > < db and user password > DB_Host:Port / Db_name on two physical machines.

  is there no work around for this problem, as I am not able to get around this error and is unable to start my managed computer node.

  Thank you

  Punishes

  Hello

  Notes on MOS:

  It is an issue that occurs because the RDBMS security store configuration problem. In order to synchronize the RDBMS security store data, WLS uses the JMS topic for transport, which is not met in this case and therefore this error. The solution is to configure the JMS topic according to the above reference documentation. However this post ideally is not an error but a simple warning message. Thus, in the context of the code fix, we delivered a patch for WLS, to change the gravity of this message of 'ERROR' to 'WARNING '. This patch can be downloaded using My Oracle Support Portal using:

  Bug number: 13459424

  Patch ID: NF9G

  Emmanuel

• \windows\system32\drivers\spldr.sys my computer does not start beyond the Boot Manager, HELP!

  \windows\system32\drivers\spldr.sys

  Hello Jayates18,

  Take a look at this link to repair your boot problem. I hope this help you. Make it a great day!

  Link: http://support.microsoft.com/kb/927392/

  "In the end, the love you take, is equal to the Love You Make"

• Satellite A60-174: system32\drivers\isapnp.sys error

  Hello
  After several nights and using Recovery CD e try my Satellite A60 will not work. Even though I cleaned it and cables everything is new.
  I got this error: system32\drivers\isapnp.sys

  I installed the HDD in another laptop and works very well. If I bring the disk for Satellite A60 I still get this error.

  OR Toshi stays to the debugger DLL when I try to install another version of win XP Pro.

  I think that the RAM or something in the motherboard is broken. Can I change the RAM from the motherboard?
  It would help if I add little ram additional RAM slot?
  (I use only the RAM stock because it is on the motherboard.
  any idea what may be this system32\drivers\isapnp.sys.

  It is said to start the laptop with Win XP cd original and try with a R.
  Well, this back do NOT work in this laptop.
  I can't come to the screen of Windows XP. The laptop will break the instalation before that!

  Konstantin

  Hello

  See this Microsoft Knowledge base article:
  http://support.Microsoft.com/?kbid=315311

  I also read that if the new facility does not resolve the isapnp.sys question then maybe it is a failure of module memory.
  Try to remove the module and test it with another.

  Check this similar subject announcement:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=11602&MessageID=52873

• xp\system32\drivers\isapnp.sys Windows 7 Code

  original title: windows xp\system32\drivers\isapnp.sys

  I have Windows XP and it won't start.  I do not have the recovery disk and I get this error message system32\drivers\isapnp.sys and I get code 7.  What can I do about it?

  Hello

  This problem may occur if the Isapnp.sys file is damaged or is not present in the path that specifies the error message. You need Windows XP installation CD to replace this file. Refer to the article below for the procedure.

  You receive a "Windows didn't start because the following file is missing or corrupt: Isapnp.sys" error message at startup
  http://support.Microsoft.com/kb/315311

  I hope this helps.