"drm activator application stop working" error when installing a game

Similar Questions

• "MessagingApp.exe has stopped working" error when I turn on the computer.

  In the last few days I have been making a "MessagingApp.exe has stopped working" message every time I spend on the laptop. When I go to "All programs" all windows and Yahoo programs are red in color. I did a search for "MessagingApp.exe" but it is not found, but when I looked in 'Program Files'-'alternative E-mail' I found it but it will not run. I can't connect to Yahoo Messenger.Can help you? I have Windows Vista Home Edition thank you, McEvor

  original title: error MessagingApp.exe

  Hello McEvor,

  1. don't you make changes to the system before the show?

  2. Since when have you been faced with this problem?

  Try the following steps to try to get the fixed number.

  Step 1:

  Try to put the computer in a clean boot state to see if the same message appears

  A clean boot helps eliminate software conflicts. Visit the link below to learn how to perform a clean boot.

  http://support.Microsoft.com/kb/929135

  Note: Once the troubleshooting is over; reset the computer to start as usual in following step 7 from the link above.

  Step 2:
  An analysis of security and verification for infections.

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  1. you can run a virus scan online from the link given below and check if the problem persists.

  Microsoft safety scanner

  2. in addition, make sure that you have installed on your computer, antivirus software was last updated so that it works correctly.

  If the problem persists, please contact support messenger yahoo from the link below for more support.

  http://help.Yahoo.com/l/us/Yahoo/helpcentral/

  Hope the helps of information provided.

• My sbe server has stopped working error when I try to burn tv recorded on dvd, try all whats'on already on this subject without success

  When you try to burn a television program recorded on a dvd, I get the error above "sbe server has stopped working" Windows media, then stops and restarts. I tried a clean restart, a restoration of the system, a check disk to dvd etc and all come out ok. Help! can I reinstall all windows Media center?

  Hello
  How long have you received this error message?
  Was there anything added/removed before it began?
  Try this:
  In the control panel/uninstall a program.
  "Turn on or off Windows features.
  * Disable media features
  * Reset
  * Re-enable media features
  Reset
  Eddie.b

• Microsoft visual c ++ runtime library stopped working, error, when you open the Control Panel, how can I solve this l

  When I log on the computer an error of windows Explorer appears, then disappears with microsoft visual c ++ runtime library stopped working, the error message.

  I try to get on the Panel, but never accesses what error microsoft visual c ++ appears every time, even in safe mode.

  Any ideas on how to solve this problem?

  grateful for any assistance

  Hello

  You did changes to the computer before the show?

  Method 1: I suggest you to reinstall the Microsoft Visual C++ Package and check if it helps:

  Package redistributable Microsoft Visual C++ 2008 (x 86)

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=29

  Package redistributable Microsoft Visual C++ 2010 (x 86)

  http://www.Microsoft.com/download/en/details.aspx?ID=5555

  Method 2:  You can also try to create a new user account and check this problem persists:

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  If the problem persists no new user account, and then fix the corrupted profile by following the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  Reference: What is a runtime error?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-a-runtime-error

• "COM Surrogate has stopped working" - error when browsing photos on the new version of Windows 7

  Just built a new pc and installed Windows 7, everything works fine but whenever I browse photos using the photo viewer, it freezes and opens with "COM Surrogate has stopped working" (after 10-20 photos - happens every time).

  I read online about possible errors - I do not have Nero or DivX installed so cannot include those. I also can not disable Protection for the execution of the data for dllhost.exe is 64-bit Windows, so it will not allow him.

  Any help would be much appreciated: it's very frustrating!

  If you have a laptop with optimus or ati changegraphic, you must add the dllhost.exe to the graphics card performance. After that it should be to fix the problem.

  concerning

  Joachim

• Yahoo messnger has stopped working error when I try to open it

  I can't access my yahoo mail when I open it it says yahoo messenger stop working, why it seems?

  You can try again but use the following instructions to support Yahoo this time (may not work better which has been suggested previously, but worth a try): http://help.yahoo.com/kb/index?locale=en_US&page=content&y=PROD_MSNG&id=SLN50&impressions=

• Java (TM) Platform SE Binary has stopped work error when editing cs5.5 for ios

  Hello

  can someone help me?

  When I try to publish in the air for ios I get 'Java (TM) Platform SE Binary Stopped working'

  tried to update my java and now using Java SE 7.

  the problem is a few days ago, before I managed to publish. the problem began without changes in my computer in java.

  Thank you

  Hello

  You face the same problem with Java 6?

  You must upgrade to AIR3.0 and see if the problem persists.

  Steps to superimpose AIR3.0 SDK in Flash CS5.5 run:

  http://kb2.Adobe.com/CPS/908/cpsid_90810.html

  Please let us know if you face any problems.

  Thank you

  Amish.

• Stop disc spinning when installing a game... (the installation stop)

  Hi, I sat with this problem for some time, with vista + sp1, the problem is, when installing games on my system, the game will install but only up to a point, then it stops and the driver (cd - dvd) repeatedly turn hangs just at the same place and there it will stay, that's why the computer stop responding

  I tried to re - install my driver but the problem still there...

  I tried to contact HP for assistance, but they could not help me...

  My hardware is: TSSTcorp CDDVDW TS-H653N

  My computer is: HP Pavilion Elite m9342.me

  Processor: core 2 quad 2.40 GHz processor

  RAM: 4 GB

  video card: nVidia 9500 GS

  I bought it just before 2 months

  Help, please

  Yes Windows has to be reinstalled or the disk drive needs to be replaced. One or the other.

• Cannot start Windows 7 Print Spooler stops (0x000006ba error) when installing or uninstalling printer.

  This PC had a fairly recent reinstallation of Windows 7, then he started screening blue, run system restore a few weeks and works very well, but it will not be printed.  When you try to install a printer, it gives a 0x000006ba error code and says that failed to start the spooler.

  The spooler may start, but stops when you try to install the printer.

  So far, I have:

  ran sfc/scannow

  Re-registration of dll

  replaced spoolsv from the windows disk

  has run a few utility programs such as tweaking.com, UVK and combofix

  Chkdsk /r

  restored back as it would go

  remove the old printer

  drivers wanted and removed old print

  deleted registry entries

  shown ancient and hidden devices in the Device Manager and remove the

  and basically, did every challenge on the internet.

  Before I'm stuck reloading this machine again, I'd like to get some really advanced or random fixes that worked for you, when others have not.

  Thank you.

  Hello Kevin,

   

  Thanks for posting your question on the Microsoft Forum.

  I would be grateful if you can provide us with the following information to help us better understand the issue.

  What is the brand and model of your printer and your computer?

   

  Try it out below mentioned methods and see if it works for you.

   

  Method 1

  This tutorial is designed to help you identify and fix common printer problems in Windows, including print errors, print spooler errors, and other issues that could prevent you from printing.

   

  Solve printer problems

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2

  You can also try running the fixit provided in the following Microsoft article.

   

  Diagnose and automatically fix problems printing and printer

  http://support.Microsoft.com/mats/printing_problems/

  Method 3

  If the question is always persistent then it means either the print spooler service is missing or damaged, I suggest you run the REG file that was downloaded in the link provided by Ramesh Srinivasan in his position, responded on June 2, 2012 in the thread link provided below.

  Deleted print spooler service

  http://social.technet.Microsoft.com/forums/Windows/en-us/9d0bd665-621d-449E-a22f-b512e068ba2a/print-spooler-service-removed

   

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Thank you.

• How can I activate an older version of Photoshop that I have loaded on my new tablet? Web activation does not work, and when I call the number, it is said that it is not longer used. In the meantime, I'm up to 13 days until it stops working due to not bei

  How can I activate an older version of Photoshop that I have loaded on my new tablet? Web activation does not work, and when I call the number, it is said that it is not longer used. Meanwhile, I'm 13 days until it stops working due to not be enabled. Help?  I really need to continue to use this product for my home business. It works very well not activated but the threat is that it will stop working in 13 days more if I don't get activated, and none of the activation methods that they list seem to work.

  You can download CS2 if you have a valid license for CS or CS2.

  And you have to follow the instructions and use the download again AND the new serial number.

• _ "Windows Explorer has stopped working" error - HELP Please! __

  I tried pretty much everything I can try in this thread, and nothing seems to work! It is very probably the the most annoying problem that I experienced with windows! I can open all the files and programs it is just that the 'Windows Explorer has stopped working"error appears literally every 5 to 15 seconds!  I click on cancel, and the other appears which says "Windows Explorer restarts" help please, I've never been more ready to give up on windows for good!

  Thank you, Bryan

  Hello

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• I get a message saying that Windows Explorer has stopped working and when I restart it pop again.

  Hi I have windows vista basic and it worked very well until yestaday and I got a message saying windows Explorer has stopped working and when I click on restart 3 seconds later, he appears once again?

  original title: Windows Vista Basic worked fine until yesterday and now I get messages saying that Windows Explorer has stopped working.
  Hello

  Use the startup clean and other methods to try to determine the cause of and eliminate
  the questions.

  ---------------------------------------------------------------

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Explorer Windows stopped working - clean Vista install

  Can someone help me please?  I installed Vista (clean install) on my desk.  It installed and rebooted, finished stage performance, was asked to choose a user name, the name of the computer and the theme.  While he was in my office - I received the Windows Explorer has stopped working error.  I have no 3rd party software installed because I just installed Vista.  Here are the details of the problem:

  Name problem: APPCRASH
  Application name: Explorer. EXE
  Application version: 6.0.6000.16386
  Application timestamp: 4549b 091
  Fault Module name: Explorer. EXE
  Fault Module Version: 6.0.6000.16386
  Timestamp of Module error: 4549b 091
  Exception code: c0000005
  Exception offset: 0000b 663
  OS version: 6.0.6000.2.0.0.768.2882382797
  Locale ID: 1033
  Additional information 1: 8 d 13
  More information 2: cdca9b1d21d12b77d84f02df48e34311
  Additional information 3: 8 d 13
  Additional information 4: cdca9b1d21d12b77d84f02df48e34311

  Any help would be really appreciated!  Thank you!

  kbrowne,

  This is a mistake of repetition or was it an appearance of time? If so run Windows Update (click Start Pearl-> click on all programs-> Windows Update-click-> click on check the updates), that solves the error message? If it does not continue:

  You run your installation from disc retail or manufacturer / recovery partition? Any changes since your last installation material?

  Please provide your computer make and model number, so that we can check the possible updates.

  ------------------------------

  First, run the System File Checker utility:

  To determine if the problem you are experiencing is caused by one or more system files that are used by Windows Vista, run the System File Checker tool. The System File Checker tool analyzes the system files and replaces incorrect versions of system files by using the correct versions.

  To run the System File Checker tool, follow these steps:

  1. Click Start and type cmd in the box start the search.
  2. Right click on cmd in the list programs, and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type your password or click on continue
  3. To order invites, the following line and press ENTER: sfc/scannow
  4. When the analysis is complete, test to see if the problem you are experiencing is resolved.

  --------------------------------------

  Next time you get this message do the following:

  1. Click Windows Logo (start)-> to the type of research - start Event Viewer, press ENTER. If you are prompted for an administrator password or a confirmation, type your password or click on continue.
  2. The event viewer is now open, in the left pane expand Windows Logs, select Application.
  3. In the right pane you will see a list of events, look for a red Logo with the error and a Source of explorer.exe, double-click it to open it.
  4. Click on copy, then paste (press CTRL + V on your keyboard), results in your response.
  5. Close the event viewer.

  Let us know your result so that we can help you.

  Rami
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Visual studio 2005 application stopped working after windows 7 32 bit OS update to service pack 1

  Hi support them.

  I did tutor which is used to record the Windows Application to the learning process. It is a 32-bit application that works fine in Windows XP and Windows 7 32 bit OS operating system. But after the upgrade of Windows 7 Service Pack 1, it doesn't now. When we try to record something, it's giving the guardian has stopped working and program disappears.
  Any product from Guardian:
  1. it is a Visual Studio 2005 application.
  2. in execution of tutor, turn us the key to register PEHOOK.
  3. some of the DLLs we use are: Interop * and other user defined dlls.
  4. it can be used to record any application Windows 32 bit OS.
  When searching I got a solution in the forum:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_programs/application-has-stopped-working-error-on-Windows7/82b6fbcd-ABA7-49e5-833d-51ce42e6ef42
  But after installing it too, the problem exists.
  Could you please help me solve this?
  Thank you very much in advance.
  Best regards
  Manu.

  Hello Manu,

  Thanks for the updates.

  Since then, enforcement, guardian, uses Visual Basic, please post this question in the Forums of Visual Studio for assistance.

  If you have any other questions about Windows operating systems, please get back to us.

• Adobe first Pro CC 2014.2 has stopped working error

  Hello guys,.

  Recently, I built a new computer with the following specifications:

  CPU: 4790 k (stock speed)

  RAM: Team Extreem 16 GB (2 x 8) (2400 mhz)

  Motherboard: Asus Ranger 7

  GPU: 780ti Zotac Amp Edition

  Storage: 250SSD Samsung evo + Barracuda 1 TB

  PSU: 850 G2 EVGA

  Operating system: Windows 7 Professional

  All the drivers are up to date.

  So I installed the creative cloud and then to install the applications in the following order: Media Encoder, Photoshop, and first Pro CC. The media and photoshop have no problem but first CC pro crashes when you click on.

  I would click on the first button CC pro and the loading screen pro first will pop up but then her 'has stopped working error' will occur immediately.

  I need to get this problem is resolved in the next few days because I need it for a very important video project. If this problem cannot be fixed in the next 2 days, unfortunately, I have to pay my subscription with adobe (still within 28 days) and use Cyberlink or Vegas.

  I have tried searching the forums and google but you have not found a solution that works for me. Could someone please lend a hand?

  Thanks for posting a screenshot of the Windows system information dialog box: StartMenu > Control Panel > system. (You can scramble all remove the computer, by domain name and workgroup down settings).

  A common cause of accidents involving the ImageRenderer.dll is not have Service Pack 1 installed for Windows 7.