DV7-4070 port

Similar Questions

• Pavilion DV7: USB Ports not working not

  The usb ports on my pavilion dv7 stopped working.  In doing research I think it has something to do with the drivers, but being not not 100% technical, I'm not entirely sure how to solve this problem.  Could you please help me solve because I use quite often the usb ports as well as to synchronize my phone etc.

  Thank you.

  Hi @laci2013 ,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion dv7 Notebook and issues with the USB ports on 10 newly installed Windows. Here is a link to solve the USB connections.

  I would like to uninstall all listed in the universal serial bus controllers list.

  Please note remove any and all USB devices and remove the memory card in the slot of the card reader. Disconnect all non-essential devices before you uninstall the controller Universal serial bus.

  Restart your computer, and then insert the USB device.

  You can try to use the Windows Update Troubleshooter to fix updates that do not come through Windows 10.  Please restart the laptop twice to make sure that all updates are completed!

  I hope this helps.

  Thank you.

• Pavilion dv7t-4000 laptop: AMD HDMI port on the computer laptop dv7 is lost after free trial Win10 returns to Win7 Home Premium edition

  My laptop was purchased in sept 2010 and runs Win7 Home Premium Edition (64-bit).

  It worked perfectly until June 2016, when the trial version free odious Win10 forced itself on my laptop.  I had no choice, I used Win10 for a day or 2 and then discovered that:

  (1) I lost the audio capability, HDMI port, I use to connect to my TV, and

  (2) the Win10 trial enabled me to return on Win7, I did without delay.

  In my Win 7 restored, everything was fine, except when I have her go in Control Panel to configure / reconfigure HDMI as the default, I couldn't - the element used to appear as "AMD HDMI Audio" is no longer displayed.  I remember a message during the free trial period Win10 that says it has disabled any material incompatible.  Without a doubt, Win10 free trial 'killed' this HDMI/device port, at least audio-wise.

  Today, I always run the same Win7, but I can't have audio HDMI on this port.  When I connect to my TV, the video works.  Win7 Device Manager it shows with an exclamation in yellow, and when I right click to get more details, there is a message saying Microsoft:

  Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might be installed a file that is signed incorrectly or damaged, or maybe it's a malicious software from an unknown source. (Code 52).

  Is there a way to 'get it '?  'this' is AMD HDMI audio.  (and wthout spoil the graphics - that is, video)

  I tried to install the drivers provided by AMD [graphics] and that did not work. The Internet from AMD website says that the audio drivers are included in the package for graphics drivers.  There is also a huge confusion in the way these low level items are named/described: ATI and AMD, because they have merged, were used somewhat interchangeably.  I also tried the graphics drivers AMD HP Support Web site specific to my laptop and it has only gotten worse.

  Thank you for your kind attention.

  Hi @ RTX,

  Awesome response. I read the details and depth of your post. I understand that the bios is updated. So you could end up with this update.

  Happens to the other updates. This will be the order.

  1. Uninstalling the driver Chipset and resettlement.

  2 reinstalling and uninstalling graphics drivers

  3. uninstall the sound drivers and reinstall.

  Before uninstalling, you can try to update the drivers supplied by device also Manager and if that market that will be great. Please, do it only if you don't have already done.

  Before uninstalling please make sure that you capture an image of the complete Device Manager window. Take some pictures of your cell phone. Please note the exact device for audio and video chipset drivers. Then, you will need to uninstall it from the Device Manager and install from the support site in the above order so that there is no confusion.

  If nothing works as a last resort, you may need to restore complete system to factory settings. Please backup your files before doing so. This is possible since the recovery of your computer's hard drive partition.

  Link to the system recovery: http://support.hp.com/us-en/product/HP-Pavilion-dv7-Entertainment-Notebook-PC-series/4284279/model/4221688/document/c01867418/

  Please hold me. I hope that it pans well.

  Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• My usb ports on my HP Pavilion dv7-6b56nr Entertainment Notebook PC

  My usb ports on my HP Pavilion dv7-6b56nr Entertainment Notebook PC do not work.    Windows 7 Home Premium 64 bit.  Product # A1T84UA.  No matter what I do, I can't get to work.  When I go into the Device Manager it shows a conflict.  When I try to update the drivers, he says that they are up-to-date.  I even tried to do a full system recovery, and if it was not for an image that I saved my computer would become a paper weight.  I am grateful, that he's back running.

  Hello

  Please install driver chipset for your machine from this link (a 2nd), this will fix a few things for you:

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207

  Kind regards.

• HP DV7 ENVY: USB 2.0 Port does not

  Hello

  I have a DV7 HP ENVY with 3 - USB 3.0 ports and 1 - USB 2.0 port. The USB 3.0 ports are working well but USB 2.0 does not work. When you plug a USB stick to the USB 2.0 port power led on the memory stick lights up but the led data is not. The computer does not at all to the inserted USB memory. The USB works fine in other 3.0 ports. I tried also to connect other USB devices, and it's the same thing. They work well on USB 3.0 ports, but nothing happens when you connect to a USB 2.0 port.

  I was looking at the USB drivers in Device Manager and haven't noticed anything that seems strange.

  I have run the system test diagnostic USB to start the system and got the following codes:

  Failure ID: 9BXQGK-6JK858-QFPK0K-8D0G03

  Product ID: C1W26EA #UUW

  No idea if this is a hardware or software failure?

  Hi @pefre,

  Welcome to the HP Forums! I read your post and wanted to help.

  I understand that the USB 2.0 port has failed on your laptop. According to the fault code 9BXQGK-6JK858-QFPK0K-8D0G03 you officer, I got following results:

  ID Tag9BXQGK-6JK858-QFPK0K-8D0G03 failure

  ChecksumOK

  16/06/Date2016 of test

  Failure Code434

  Device

  Communications

  Includes

  GPS, HUB, Modem, network, map network drive, PCI, PCMCIA, Switch, USB card

  Error message

  Failure of USB (not specified)

  It seems that there is a hardware failure with the USB port.

  Is your laptop still under warranty? If so, please contact support phone HP load a repair:

  Please the following link http://www.hp.com/contacthp allows you to create a folder for your problem and contact HP. If you do not live in the United States / Canada, please click on the link http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html to get contact information for your region.

  Please let me know if that solves the problem by marking this message as "accept as a Solution.  To simply say thank you, click the thumb upward below!   If you need more assistance let me know and I will gladly do everything I can to help. Thank you.

  Kind regards

• usb 3.0 ports dv7-6b56nr

  Please help, I have a hp dv7-6b56nr, and all of a sudden, ports usb 3.0 has stopped working. I bought the refurbished laptop from wal mart. For some strange reason, I can always used to load usb chargeable items.

  Hello:

  Please see if (re) install the chipset driver solves the problem.

  Download and install the first listed file that contains the USB 3.0 drivers.

  http://support.AMD.com/us/gpudownload/Windows/pages/raid_windows.aspx

  Paul

• Pavilion dv7-6135dx: HP Pavilion dv7-6135dx - USB 3.0 port is?

  Hello. I'm trying to find out what my laptop usb ports are 3.0. I tried a USB SS symbol on the sides, but I don't see such a thing. On the right side, I see a USB symbol, but it doesn't have the SS beside him. I tried to find out if there was a difference in color (blue or black) and the right of those who do not seem completely black, they are somehow bluish in color but still results in google, I understood that the left has usually 3.0 ports. So could you help me out here, please? Pavilion laptop dv7-6135dx, which side has the Ports USB 3.0?

  Hello

  The two usb ports on the left side are 3.0

  Kind regards

  DP - K

• How I fixed my USB ports not working not problem. Two ports left side previously does not... HP Dv7

  So I do not know what is not "where it will honestly, but put there just to try to help someone else who has struggled with this as long as I did it...» I ended up having my two USB ports on the left side (turned out to be my 3.0 ports) working again when they recognize nothing. I could use the USB 2 on right 2.0 ports, but the transfer rate was terrible.

  My answer on another question where someone had a similar problem... good luck!

  'Hi. '

  Not sure if this will help, but I had the same problem, the two ports on the left did not work on my Dv7. All this time I thought that the USB on the right were my 3.0 ports so I thought that would be nice, but it's been over a year that I initially had this problem and made a bunch of maintenance of the system meant that I would look through it again. In any case, I went to the Device Manager through the computer management tool. I know that you can go straight to the Device Manager, but just give you exactly how I did it. You can search just to start computer management.

  So I chose Device Manager in the menu on the left side and it looked like ordinary Device Manager. Went down to Universal Serial bus controllers... at this stage, I watched the action menu on the right and select more actions, opinions and you click Show hidden devices. After that I went through my USB controllers one by one as I had done many times before and checked them, tried the update of drivers, etc... Under the USB controllers Section, I noticed something like xHCI Host controller of compliance Test... I right click it and went into its details, I tried the driver updated and installed the new driver. 2 new USB controllers immediately arises: Renesas Electronics USB 3.0 Host Controller and root hub.

  Switched on a test drive from the right thumb to the left and the computer instantly recognized and installed the driver for the stick.

  And that was all... hope it helps even if this is later. "

  Hi @klark1kent,.

  Thank you for visiting the Forums Support HP's, welcome and thank you for the important information.

  Have a good week.

  Thank you.

• Pavilion dv7: 2 usb port does not

  Hi, two of my three usb ports don't work or devices recoginse (both right), but the one on the left recognizes all the devices, I plug.  How can I get the two on the right side works correctly?

  Concerning

  Hello

  are a 4 USB 2.0 ports.

  • 4 USB 2.0 ports (4th port shared with eSATA)
  • 1 eSATA + USB port (left port)

  HP Pavilion dv7-4131sa Entertainment Notebook PC product specifications | HP® Support

  The difference is that the ports on the left are integrated on the motherboard, rights USBports are a card with a cable that can be replaced in case of failure.

  If you have a distribution of Linux (Ubuntu, Mint...)  You can use it in live mode (without installation) to test the USB ports

  Manual (page 80-81)

  http://h10032.www1.HP.com/CTG/manual/c02642701

  related topic

  HP PC - troubleshooting connections USB (Windows 7) | HP® Support

  

• Pavilion dv7-7071sf: USB port does not

  Hello!

  First of all, I apologize for my poor English, hope that you carry a grudge on me on this subject.

  I accidentally deleted the bios battery connector yesterday while I was remove my computer (cleaning with dry of butane air blower and replace thermal paste), so the bios reset...

  After that, the USB ports on the right were not functioning more, IE. they always provide the power for any USB device that them are attached (tried with fan, external hard drive and mouse), but does nothing else (mouse not working not, disk appears not, no sound windows indicating a device has been connected...).

  Here is a list of the things that I tried to fix it:

  • Disassembled my computer again to check if I have everything connected correctly
  • Removed the battery and the cable and held the power button for more than 1 minute and a half
  • Update the drivers (Intel Download Center expandable 3 USB host controller driver)
  • Removal of windows drivers to install its generic those
  • Restore my computer at the time when I had everything working well.

  None of these manipulations worked, and the right usb ports (two usb 3.0) were still not functioning while those on the left (usb 2.0 and usb 3.0) were.

  I assumed it was a matter of windows, so I tried to format my hard drive, using the tool of recovery (F11).

  As for now, complete recovery, windows is installed, but all ports (left and right) are no longer.

  They still offer a power of my devices, but won't fire any action of windows.

  I'm in the show right now the updates of windows, but I don't really expect a lot from him.

  How can that being said, I solve this problem?

  I would appreciate your help on this,

  Thanks in advance.

  HP Pavilion dv7-7071sf (almost 3 years years).

  Using 64-bit windows 7 OS.

  Disk used: Western Digital USB 3.0 compatible with USB 2.0.

  Used the mouse: the mouse Bioxar.net & Steelseries (call of duty Black Ops II)

  Hey once again!

  Thanks again for your help freedomwarf (and all those who have spent the time to read this topic), the problem has been resolved.

  A friend told me to make a CMOS clear, which I planned to do, but I have not found the mutator.

  What I found instead was me forgetting to plug in the data cable to the motherboard (only the power of one was linked in).

  Thanks again for your help!

• Pavilion dv7-4177nr: dv7-4177nr right usb ports not working not

  So I recently bought a used dv7-4177nr, got home, and since it has been used, naturally the first thing I do is restore the system to factory conditions. I don't check the ports for a feature beforehand. Run all Windows updates, get rid of the bloatware and realized, "it would be easier with my mouse wireless." Go to plug in, and the ports on the right do not recognize. No sound of "you hooked something up" or looking for drivers or anything like that. Those on the left are working fine. Windows detects that there is no ports.

  I tried the things:

  Update the BIOS

  chipset drivers of the series AMD 8 (not completely sure that those who have the right ones, but nothing else has blown up or whatever it is)

  Remove the USB drivers from Device Manager and let Windows RE-add-the

  

  The left USB ports are directly on the motherboard and the ports on the right side

  on a removable daughter card.

  USB card (includes cable) 605348-001

• DV7 - 3153CA: made my DV7 - 3153CA have ports USB 3.0?

  The laptop has an i5 processor and has 4 USB ports. 2 on each side. One of the ports on the left is a combo

  eSATA and USB. I have no SSUSB marks anywhere.

  In addition, in the affirmative, is it necessary to have also a special to connect to a USB 3.0 USB 3.0 cable equipped

  mobile phone or not?

  Thank you

  Hello

  No, there no USB 3.0 as shown:

  External ports:

  • 5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card
  • 4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA
  • 2 headphone
  • 1 microphone input
  • 1 HDMI
  • 1 VGA (15-pin)
  • 1 eSATA + USB 2.0
  • 1 RJ - 45 (LAN)
  • expansion port for computer 1 cell 3
  • 1 IEEE 1394
  • FireWire (4-pin)
  • 1 consumer IR (remote receiver)

  Source: http://support.hp.com/us-en/product/HP-Pavilion-dv7-Entertainment-Notebook-PC-series/4074368/model/4126017/document/c01980764/

  Kind regards.

  Note: You can use existing USB cable phone(s) or Tablet (s), no need for new cable for USB 3.0 ports.

• Pavilion DV7-6c23cl AMD quad core laptop there a 2nd Bay and a port?

  Hello

  I'm looking for a laptop that can accommodate two hard disks (I want a smallish SSD for the system and a conventional SATA, more great for data), I've read that at least some of the Pavilion DV7 laptops with a drive Bay 2nd (& port). Costco is currently selling an image based AMD Pavilion DV7 (dv7-6c23cl) that seems attractive. What I need to know is: has a drive Bay 2? Thank you.

  Ron

  Hello

  It has bedroom (or Bay) for a second HDD. You need a caddy for her. There are a LOT of people have done this upgrade and there are also a few videos on the net. You can Google "HP dv7 second HDD.

  Kind regards.

• Expansion on Envy dv7 port

  Is there an expansion port to connect a dv7 envy a QuickDock laptop?  If so, where?

  Thank you for your help but I'll just assume that there is NO one on this model's expansion port

• Problem with Port on the DV7-3079wm of charge

  Hello world.  I searched the forum for this question and other places and I think I probably know what is the problem, but I wanted to make sure that before I go ahead with trying to fix and get some advice on my specific problem.

  I have a HP Pavilion DV7-3079wm running Windows 7 64 bit.  I have problems with the laptop to load.  I've already replaced the battery to eliminate this problem, but I need one anyway, because one was not maintain a load more.

  So the problem is when I plug my power adapter most of the time that he does not even recognize that I have it plugged.  No light load on the side or the front.  So if I slowly wiggle out or try to angle in one sense or the other, eventually he'll catch a connection and then 1 of 2 things going on.  Either she viewed the laptop too long that I do not move the charger of whatever the position in GOLD, it pops up a message saying "Smart AC output adapter is too weak for this computer." and then proceeds to the load of the laptop or it just says: "plugged in, do not load.

  I do not know if my problem is the AC adapter or if the port inside the laptop is messed up, which from what I've read on other forums requires either a new motherboard or tear down my laptop and re - solder a new fee on the motherboard port.

  I can't wait to buy a new adapter if it isn't the problem.  Also another problem, I am very happy with my laptop and really intended to max on memory and improve for one SSD but I don't want to sink money into it until I get this problem resolved.  Any help would be appreciated.

  Thank you

  No rust spots on the inside or outside of my plug adaptors CA.  I finally just went and got a new adapter and when comparing it to mine its all brilliant inside the end of the plug where mine is dull looking.  Which may mean it was just salty and was not getting a good connection.  A new Bill without problem, and immediately, although she Wiggles, if fortunately is not the port inside the laptop.  I'll try to clean my AC adapter / CC and see if it makes too much work again.  Thanks for everyone's help and info that it was appreciated and he has helped guide me in the right direction.  Also, if the port never turn off, now I know where to get a replacement.

  Up next... go to the SSD & maxing out the memory.  I can't wait!

  Thank you!!!