e-mail unavailable because "in use on another device?

Similar Questions

• You don't you email / account that Roadrunner mail is used by another device?

  While reading my email yesterday a gray box appears on the screen that says "cannot get mail / Roadrunner Mail account is in use on another device, then a pop up says your software must be updated to 9.3.4... so, I press the button install... it starts to update... the thing is that I don't date my iOS to 9.3.4 the day of the update is out. I think it is 08/08/16...

  the update finished I read my email and I get page to configure an e-mail account, I'm looking for my roadrunner acct and he went...

  Today, I get the ipad3, I have time to work on the problem now... to my amazement my roadrunner e-mail account is back, rated and work.

  Everyone thinks I should be concerned about this chain of events... I'm always worried about hackers, any help appreciated. Thank you

  Sounds more like a messed up iOS upgrade than someone hacking into your device.

• "The port is used by another device. Printer does not print.

  I have a printer Canon D661 on an Ispiron Dell s 545 under Win XP SP3.  Everything worked fine until today when he leaves the impression.  I have uninstalled/reinstalled the printer through Windows and through the uninstalling Canon.

  I have downloaded the latest drivers from Canon, did all my XP, updates my Dell updates driver material and restarted several times than I can count in the process.

  I've stopped and started the print spooler.

  Still nothing will print.  The printer status window insists that "the port is used by another device.

  I ran impression of Microsoft Diagnostic tool, he says that's all right.

  It is a USB port, as the mouse and keyboard.  Nothing else.  I tried swapping USB ports between elements, no help.

  The printer works fine if I plug it into my USB netbook, so it's not the printer.

  I receive the error message even if the printer is connected to the office he "belongs" to.

  Until yesterday it worked fine, same print network jobs on other computers.

  I went home from 11:00 to 18:30 today.  Help?

  Thanks for the reply!

  I tried what you suggested, but it did not work.

  Finally, I got it going.  For some reason even if it was still installed on LPT1 on that question and two other computers, this computer has stopped working.

  I found the installer was not obvious choice to install on USB1 and that was when he started working.

  Interestingly, it works installed on LPT1 on two laptop computers when it is connected in fact on their USB ports.

  Thanks again.

• When I try to scan with my CanoScan N640P ex scanner I receive a message indicating the Port to the printer that is used by another device. How can I work around this problem?

  When I try to scan with my CanoScan N640P ex scanner I receive a message indicating the Port to the printer that is used by another device.  How can I work around this problem?

  Hi ejp70,

  1. did you of recent changes on the computer?

  2. to when was the last time the scanner was working fine?

  3. you have any other printer\scanner connected to the computer?

  If you have any other printer\scanner connected to the computer, disconnect them and check if it works.

  I suggest that you uninstall and reinstall the scanner to the computer, also make sure that you install the latest drivers for scanner on Canon website.

• Ability to export an entire project for use on another device?

  I'm in half way through a project (with lots of pictures and always associated with him) on my PC at home, but I'm on to head out of country for several weeks.

  Is there a simple way to export the complete project for me to work on my laptop while traveling, please? (I can then re - import to my PC at home on my return)

  (I think as Lightroom where you can export a catalog to facilitate this)

  Thanks in advance.

  While you try to move your project from one computer to another?

  In this case, use the project archiver, under the file menu. It will move your project file and all of its multimedia files associated with a device to another.

• That means "another device on the network use the IP address of your computer"?, that means "another device on the network is using the IP address of your computer?

  That means "another device on the network use the IP address of your computer"?, that means "another device on the network is using the IP address of your computer?

  A

  Most likely, the computer becomes a network address of a router. The assignment of an address ("lease") expires and must be renewed after a certain period of time, which could be an hour or a day. The lease expired without being renewed because the device has been disconnected at the time. Meanwhile, the address has been leased to another device on the network, or maybe the router has not updated its list of addresses the leases. When the device offline comes back online, a conflict results. Depending on the type of router you have, the conflict can resolve itself automatically. If not, then in the menu bar, select please

  ▹ System Preferences network ▹ 

  If the preferences window is locked, click the lock icon in the lower left corner and enter your password to unlock it. Click the Advanced button, and then select the TCP/IP tab in the sheet that drops down. Look at the menu option

  Configure IPv4

  If the selection in this menu is

  Using DHCP

  Click on the button

  Renew the DHCP lease

  Test.

  Make sure that you have more than one DHCP server on the network. That could happen if you have more than one access point Wi - Fi, or if you have a router and broadband a wide device distinct in connection mode sharing.

  B

  Less likely, you have a network address that you assigned yourself and another device is itself by assigning the same address. In this case, the selection to configure IPv4 menu will be either manually or using DHCP with manual address. This kind of conflict will not be resolved automatically. You have the following options to solve:

  1. Change the selection in menu using DHCP.
  2. Change the address assigned manually to one that is not used by another device.
  3. Change the address of the other device.

  Which of these options you choose depends on the details of why you use a static IP address. Any changes you make to the network settings is necessary before taking effect. To do this, click OK, and then click apply.

  If the router is also your device at wide band, then he may be operating in bridged mode. In this case, only one customer at a time will be able to connect to the Internet. Consult the manufacturer or ISP documentation for how to reconfigure the device in the connection mode sharing.

  C

  According to a report a "DirectTV" receiver can cause the problem. If necessary, disconnect the device from the network, or power off and test. Consult the support services provider.

• IR hotsync problem: "because the port is in use by another application."

  I finally got my system operation.  Sony Clie TJ - 25 pda, Palm Desktop 4.1, Windows 7 64 bit.  Very delicate balance.  I failed to install the new software released by aceeca.  I finally got it by infrared hotsync.  Several times.

  Now, today, I get the message on the Clie: "could not start the hotsync operation because the port is in use by another application."

  I saw this thread and in fact ensure that the transfer of images using a digital camera box is unchecked.  It still does not.  The icon hotsync in the lower right part of the screen, when I check that IR is checked, nothing else is.  It still does not.

  Thoughts?  Ideas?  Suggestions?

  Cidercat I had this happen to me with bluetooth hotsync before. I listen to radio, transfer files and surf the web with bluetooth. I could solve the problem by turning off the bluetooth, then turn it back on. Sometimes a warm reboot might also work. I came across a free application for the Palm tree named NetworkDown. It closes completely all active sessions down. You type right on the icon to run it. It works on my TX.

  http://www.metaviewsoft.de/en/software/PalmOS/freeware/other/NetworkDown.PRC

• Cannot run chkdsk - Chkdsk cannot run because the volume is in use by another process.

  original title: can I run chkdsk on win xp home, but when I try to use switches, I get cannot lock the current drive. Chkdsk cannot run because the volume is in use by another process. HELP PLEASE

  I run chkdsk without switches on win xp home. I told myself I file error and to set running chkdsk with /f. but when I try, I get the cannot lock the drive, chkdsk may not run because ect...  I tried in safe mode, same thing. I sfc/scannow, but it has not fixed the problem files. help please

  It's normal.  You can not run a check disk on your system disk because your system is to use.  The Message you get should ask you if you want to run it at the next reboot.  You must answer 'Yes' to this message, and then restart your computer.  A disk check should take place as it is restarted.

  FYI: A check disk can take hours if you have a large drive or there are a lot of problems on the disc and you cannot use your machine while the scan is in progress.  Better to operate during the night.  Also, I got checkdsk completely erase the hard disk to the point where the only option was to reformat and reinstall Windows.  Make sure that your data available are well-supported before running Chkdsk.

  "How to perform disk error in Windows XP check"
    <>http://support.Microsoft.com/kb/315265 >

  HTH,
  JW

• System 32 error (0x00000020): "the process cannot access the file because it is being used by another process.". The operation to open the file will fail with error - 1032 (0xfffffbf8(JET_errFileAccessDenied))"

  Original title: svchost (1020)

  Event type: error
  Event source: ESENT
  Event category: general
  Event ID: 490
  Date: 2010-10-19
  Time: 14:51:34
  User: n/a
  Computer: ROB
  Description:
  Svchost (1020) an attempt to open the file "C:\WINDOWS\system32\CatRoot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb" for read / write access failed with the error System 32 (0x00000020): "the process cannot access the file because it is being used by another process.".  The operation to open the file will fail with error - 1032 (0xfffffbf8(JET_errFileAccessDenied)).

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Hi Robrw,

  1. when exactly you receive this error?

  2. don't you make changes to the computer before this problem?

  You can try to rename the catroot2 folder and check if it helps.

  Step 1:

  a. Click Start and in run type C:\windows\system32 and click ok

  b. find the Catroot2 folder. Right-click on Catroot2 and rename it to Catroot2.old

  If you are not able to do the normal mode, try to start in safe mode and rename

  Check out the link for more information on starting your computer in SafeMode below:

  http://support.Microsoft.com/kb/315222

  Step 2:

  If you are unable to access the catroot2 folder, and then try to change the permissions on the files and check if it helps.

  See the following article:

  How to capture a file or a folder in Windows XP

  http://support.Microsoft.com/kb/308421

  Step 3:

  You can also try to temporarily disable third-party security software and firewalls and check what is happening.

  Note: Activate the security software after the resolution of the problem.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Chkdsk cannot run because the volume is in use by another process

  My computer was working fine until last night. Now when I connect I get a blue screen saying that the computer shuts down to prevent further damage from happening. I tried to restore to an earlier point in time when my computer was working but then I get the error:

  The OS disk (C :) has errors.
  Windows has detected corruption on OS (C :) file system. You should check the drive for errors before you can restore it.

  So I'm going to run the chkdsk utility, and I get the error:
  Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts.

  I'm confused because the chkdsk unility usually works, and I have no idea why she is being used by another process. I am clearly not very good with computers. I tend to do a lot of spywear and adwear on my computer. I have Spyware Doctor that removes any infection.

  Help, please. I've tried everything. Thank you.

  Asha22,
  It appears from your last post why chkdsk did not run on reboot and you gave an incorrect message is that you did not a space between the volume and the f number.  The correct syntax is:

  CHKDSK c: /f

  You can also run the utility disc in this way:
  http://windowshelp.Microsoft.com/Windows/en-us/help/bc1393cf-9f9c-79C7-0f91-9337c2c41f811033.mspx

  1. open the computer by clicking the Start button, click computer.
   
  2. right click on the hard drive you want to check, and then click Properties.
   
  3. click on the Tools tab and then, under check for errors, click check now.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  To automatically repair problems with files and folders that the scan detects, select automatically fix file system errors. Otherwise, the disk check will simply report a problem, but not to fix them.

  To perform a full disk check, select search and attempt to recover bad sectors. This scan is trying to find and repair physical errors on the hard drive itself, and it may take much longer to complete.

  To check for errors file and the physical errors, select both automatically fix errors in file system and search for and attempt recovery of bad sectors.
   
  4. click on start.
   
  Depending on the size of your hard disk, this may take several minutes. For best results, do not use your computer for any other tasks while it checks errors.

  Note: If you select automatically errors in file system of fix for a disc that is used (for example, the partition that contains Windows), you will need to reschedule the disk check for the next time you restart your computer.

  The reason that it says that the disk is in use by another process is because it is in use by the operating system (Vista), and that's why it must be run at startup, before the operating system loads fully.

  Another utility, you need to perform is the System File Checker, if you can get your computer to start, either normally or in Mode without failure.
  To run the System File Checker tool, follow these steps:
  Click Start and type cmd in the box start the search.
  Right click on cmd in the list programs, and then click Run as administrator.
  If you are prompted for an administrator password or a confirmation, type your password or click on continue
  At the command prompt, type the following line and press ENTER:
  sfc/scannow
  When the analysis is complete, test to see if the problem you are experiencing is resolved.

  Let us know what these tests are and how we can also provide assistance.
  Thank you

  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I installed windows vista on my new computer, I tried to turn it on, and it said I couldn't because it is already in use on another computer?

  activation help problem!

  I have a Windows Vista Ultimate Edition installation disc that was purchased separately from any pc from microsoft and installed on my old laptop, but now that the laptop is broken and I have a new, but when I installed windows vista on this news, I tried to turn it on, and it said I couldn't because it is already in use on another computer? What can I do to remove my old one and activate it on my new?

  You must use the Activate by phone and speak to an operator.

  telephone activation.
  Click the Start button
  in the search box, type
  SLUI 4
  and press the Enter key
  Follow the instructions - but when asked which service you need the ansafone phone, don't answer - it should oblige the operator to answer, who can deal with you.

• Error: "the process cannot access the file because it is being used by another process." when treid to install the device driver

  Original title: Windows cannot install the drivers

  I had a lot of trouble installing the drivers on my Windows computer.  I went straight in the Device Manager and deleted the devices I tried to install and reinstalled them, I went into safe mode, I got Windows to run the console and only the basic process and run from there Device Manager... no matter what I do the same mistake.

  "The process cannot access the file because it is being used by another process".

  Even after a restore of the system, he did this, and I don't know what to do anymore.  Only devices that have been previously installed work.

  What's more important install my Blackberry software because my phone is broken.  The software cannot detect my phone because the drivers have not been installed.  Most of the devices I can use with Linux (I have Windows Vista and Ubuntu running on the same computer), but RIM don't make Blackberry for Linux software, so I have to do it on Windows.

  Hi paco2012,
   
  1. did you of recent changes on the computer?
  2. how many user accounts you have on the computer?
   
  Try these steps and check the result.
  Step 1: Install the driver as an administrator
  a. shut down the computer runs.
  b. start the computer and the connection as an administrator.
  c. find the driver configuration file, right-click on the file and click "Run as Administrator".
  d. follow the instructions in the wizard to install the driver.
  e. restart the computer once the driver is installed.
   
  Step 2: Try to install the driver to boot either by disabling all non-Microsoft programs
  a. open the article: http://support.microsoft.com/kb/929135
  b. Article, follow "step 1: perform a clean boot."
  c. restart the computer.
  d. install the driver and verify the result.
  e. follow "step 7: reset the computer to start as usual.
   
  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• RunDLL__Error C:\windows\system32\sshnas.dll___The loading process cannot access the file because it is being used by another process.

  When I start windows Vista, I get the error message:

  RunDLL
  Error loading C:\windows\system32\sshnas.dll

  The process cannot access the file because it is being used by another process.

  How can I fix?

  Hello

  It is the result of malware, then do a very thorough check and when the system is
  clean see the following message to remove this error.

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often easy
  to detect malicious software often comes with a much harder to detect and remove the payload. Then
  its best to be thorough than paying the high price later now too. Check with them to one
  extreme overkill point and then run the cleaning only when you are sure that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
  the regular windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/products/malwarebytes_free

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp?prevx=Y  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  -----------------------------------

  Original version is now replaced by the Microsoft Safety Scanner
  http://OneCare.live.com/site/en-us/default.htm

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  ----------------------------------

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
  system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• executable files: cannot access the file because it is being used by another process

  Hello
  I created a file named test.bat on my desk
  baptized "test.bat" and sent the notebook, wrote "REM" and recorded.
  so, I closed my notebook and reopened, has added another "REM" and saved the file again.
  then I tried to rename, move the file to another folder and delete
  everything went without any problems.

  But if I create the file and run it, the command prompt will appear for a while and then disappear.
  I can rename or move the file without any problem,
  But if I try to edit the file in Notepad, I get this error:

  The process cannot access the file because it is being used by another process.

  and the file is not saved.

  also, if I try to delete the file, it seems to be deleted until I press F5, the file appears again.
  When you try to rename/move this new file, I get another error:

  File Access Denied

  You need permission to perform this action

  You need the permission of the administrator of the computer to make changes
  in this file

  It seems the file is opened (or if I choose to delete) after a few minutes, then it is not if I try to access
  the file (I kept pressing F5 every few seconds for 15 minutes and the file is missing)

  the problem appears if occuar with any file name, anywhere, not just the office or home by car, not even on the same disk,
  while I had no problem when I started in an old installation of windows xp and repeat the same steps.

  I tried to use the sysinternals utility handle, that's what I have:

  After creating test.bat:
  C:\Users\User>handle test.bat

  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  No found the corresponding handle.

  After you run test.bat:

  C:\Users\User>handle test.bat

  Handle v3.51
  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  System pid: 4 type: file A18: C:\Users\User\Desktop\t
  EST.bat

  has obtained the result above after attempting to remove test.bat also.

  After the creation of othertest.bat:

  C:\Users\User>handle othertest.bat

  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  No found the corresponding handle.

  After execution of othertest.bat:

  C:\Users\User>handle othertest.bat

  Handle v3.51
  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  System pid: 4 type: BD0 file: C:\Users\User\Desktop\o
  thertest.bat

  After you rename the othertest.bat:

  C:\Users\User>handle othertest.bat

  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  No found the corresponding handle.

  C:\Users\User>handle renamedtest.bat

  Handle v3.51
  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  System pid: 4 type: BD0 file: C:\Users\User\Desktop\r
  enamedtest.bat

  the also occuars when I run any .exe file and delete it after its finished running, I deleted
  the handle.exe and the handle64.exe after the test above and at the same time returned when I updated their records.

  can someone help me?
  IAM using Windows 7 ultimate 64-bit.
  Thank you.

  I struggled with this VERY ENNUYANT thing for a long time on a Windows Server 2008 R2.

  Just found the answer:

  http://superuser.com/questions/260375/why-would-system-continue-locking-executable-file-handles-after-the-app-has-exit

  Activation of the service 'Application Experience' does the trick for me.

  If I got paid for every minute spent dealing with the mysteries of Microsoft... No, wait! Paid!

  Thank you Microsoft!

• Organizer of Photoshop: The catalog could not be opened because it is currently in use by another program

  Original title: Louise

  I think I can cut my computor while organizing photoshop was running. Now when I try to open an icon appears on the bar tasks with a noise of error. I can fly over the icon and it shows me my photos but I can't open, all I can do is to close. It was suggested to go to Task Manager and shut up there and the first time I tried this he showed that run and I closed it down. But I still can't open it and it shows is no longer in the Task Manager. I got a message

  The catalog cannot be opened because it is currently in use by another program.
  I tried the system restore to a time before this glitch.
  I have uninstalled and installed the program.
  How can I find where it runs when I can't find it in the Task Manager?

  Hello

  I suggest you to send your query to the Adobe community forum as they would be in a better position to help you with this question.
  http://forums.Adobe.com/index.jspa
  https://helpx.Adobe.com/Photoshop-elements.html

  Thank you