Edition in burst mode stuck at 0%

Similar Questions

• HP/Agilent 33120 A pulse, use burst mode

  Hello

  I'm trying to trigger a pulse of demand on from a HP 33120 A function generator.

  The pulse must be a 0 - 5V simple, with frequency/period adjustable ramp. I was able to get as much of the FG by use of burst mode and trigger manually on the front panel. Now, I would like to get the same functionality from a LabVIEW VI.

  Although there is a driver for the device, the burst feature is, unfortunately, not applicable to the model that I use. I found a similar problem on the forums and follow the code of the SCPI provided in the answer with some of my own humidification (http://forums.ni.com/t5/LabVIEW/33120A-Pulse-Mode/td-p/1088106).

  Unfortunately, my VI does not produce the same waveform as the manual release out of the front panel. It hovers at the offset value and gives me a few square wave to zero when I run the VI. Square waves are spaced oddly and I usually see 4-5, even though I specified 1 cycle in VI. The 33120A reading, I feel that this is of my do not turn off the previous signal but, if this is the case, I can't understand how I would do.

  I start to move away from using only the drivers by changing the code of the SCPI, but I'm still pretty new to this. Would appreciate some advice on what could be the problem. I modified my original VI twice; Once configure only the FG burst wave parameters manually and one just put up the waveform with no shine. The first don't not gave me much better results and the works of the latter very well so I'm back to the question of thinking are in transition.

  I enclose the original VI (b) with the two modifications to the case where (c and d).

  Hope to hear from you,

  Yusif Nurizade

  Edit: Burst chain should say TRIG: SOUR BUS instead of EXT, although neither works.

  Or you have the appropriate firmware in you function generator?
  Have you checked this with Agilent?

• I have an i phone 6 (9.3.1) I can disable burst mode?

  I get the burst mode, even though I type quickly once the button in photo taking!  I don't want this feature on my phone!

  At the top of the camera screen press "hdr" and turn it off.

• Sony As100v how can I use the burst mode?

  as the gopro, you can take a picture like 10 frames / second

  Burst mode is now available on the new firmware... But do not install it again. People who have problems with their cam action during and after the upgrade of the firmware. Wait a little more clearly and correct installation of the update.

• HP DM4: My HP DM4 Beats Edition right hinge was stuck.

  Help, please!

  My HP DM4 Beats Edition right hinge was stucked and caused the screen (where the hinge is attached) to the slot. Now my screen is completely down. I want to know if I can still get this repaired. This notebook is so expensive and yet I've had only 1 year and 6 months now.

  @Rudeskagirl27 ,

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message after the weekend to contact HP identified. Also, keep in mind is not to publicly display (serial numbers and information)
  
  See you soon,.

  KarolB

• Slow buffering when shooting in burst mode high with my 7DMarkii... What is the fastest SD card?

  When shooting in burst mode high with my 7 D Mark ii, I do not get optimal performance... the buffer fills up fast and backup... while I can't take shots more... I disabled the quite high definition noise reduction... Usually, I only have an SD card in the camera. I do not use the other card slot... is it because I didn't have the fastest SD card... For those of you who shoot regularly 7 D Mark ii, make it a point to always shoot with a SAndisk SD 95 map... ? I'd get better performance if I used the slot for CF card or both?

  IRIS says:

  I'm shooting with a single card (SD), a Lexar pro 64 GB 150 MB/sec Class 10 and 3 inside the U (whatever that means), but I show a limit 16 popping up on my screen... so I do not understand... I'm shooting a low ISO... I have disabled noise reduction... I'm shooting a Standard picture style... I'm shooting RAW only... My battery is charged... Then why is it backup and buffering so often? I forgot something? is it's just that the CF card is faster? .... I doh't understand why I don't get the perfromance promised high 20 + something burst shots...

  First of all, Yes, CF cards are faster.

  Second, the number you see is the current buffer and does not include the write speed of your card.

  The only way to tell what your real brightness issue is therefore to test.

  Shooting RAW to SanDisk Extreme PRO 32 GB 160 MB/s UDMA 7 CF Card, I get about 30 shots before the outbreak slows. My viewfinder shows 15.

  Note When your feature of gust of defined test cards your lens to manual focus (MF) because according to your settings of priority to focus the camera auto focus can slow or even stop your glow.

• Burst mode

  Recently when reading an article, I came across the phrase
  
  "f the application deployed using burst mode, then... otherwise if application is deployed as a Coop like ear, war etc. then...". »
  
  What is an exactly burst mode?

  Hello
  Please find below urls for a deployment of the application in burst mode.

  http://docs.Oracle.com/CD/E15051_01/WLS/docs103/deployment/deployunits.html
  http://docs.Oracle.com/CD/E11035_01/WLS100/deployment/autoDeploy.html

  Select this option if this helps you.

  Kind regards
  Kishore

• Edit in Html mode in licensed content and everything disappear

  Whenever I try to edit in Html mode in catalyst for business affairs. All the content will disappear.
  Now my head it's all gone! and don't look like I can cancel it

  Normally, this occurs if the html code is ill-formed, without close tags or incorect training, the Publisher tries to correct this upward but sometimes just drop it will.

  It is also only XHTML compliant, so if you have no HTML5 it don't know what it is.

  Really try and avoid html stuff in the display of the html editor.

• Illustrator crashes after editing in model mode

  I use Illustrator CS6, Windows 7, Intel (R) Core (TM) i7-3770 CPU @3. 40 GHz, 16 GB RAM, 64-bit operating system. I use the characteristic editing model a lot, and recently it starts crashing, usually, when I try to save after editing in model mode (it started just to do this). I don't know why he started doing that, and it doesn't have anything to do with the complexity of the design. Any advice would be appreciated.

  Since you said recently watched crashing, very probably reset you AI prefs will solve this problem.

  Start Illustrator, then immediately then press Ctrl, shift, Alt to reset the prefs.

• Windows xp home edition. I'm stuck in safe mode after accidentally clicking on diagnostic mode.

  tried to change but whenever I restart, I find myself a SafeMode because C:/cmdcons/bootsect.dat=microsoft windows recovery console/cmdcons. Any ideas?

  Hello

  This happens if the switch/SafeBoot is added to the Boot.ini file. / Safeboot parameter forces a boot in safe mode by using the specified parameters. The available parameters are:

  a minimum

  network

  SafeBoot: minimal (AlternateShell)

  For more information about the boot.ini switches, see visualization and correction of the parameters in the Boot.ini file on x 86 systems
  RESOLUTION

  a. Click Start, run and type MSCONFIG

  b. Select the Boot.ini tab

  c. If you dual-boot for installation, select the appropriate under [operating systems] entry

  d. in the section Options start at the bottom, uncheck/SafeBoot

  e. click OK

  f. restart Windows

• Lasso mode stuck in more CS5 tool

  The lasso tool works very well to make a selection.

  When I click again, an asset appears next to the cross, and the lasso tool is stuck in a mode to create additional selections.

  He désélectionnera not what is there.

  To deselect, the only way is to use the tool of marquis or Ctrl - d.

  Very frustrating when you are trying to work.

  Is this a fixable bug?  Any ideas how to make the lasso to stay in mode tool ordinary then it deselects a previous selection?

  Have you checked the selection parameters in the options bar?

  It seems that you have selected the second on the left, not the first (default).

• Launch The Witcher Enhanced Edition in administrator mode

  I just bought The Witcher Enhanced Edition and installed. When I go to run the game it says "insufficient privileges: you must be an administrator to run this application for the first time." So I right click and select run as administrator, same thing, I uninstalled and right clicked reinstalled with a right-click Run as administrator, still a lot of hole of nothing. I just unlocked my administrator account, repeat the previous steps 5 times still same thing. If someone can please help me because I don't know how much more administrative I can get before I destroy it windows 7.

  This update did not help, but I found the correct update thanks for your help.

  Update link is http://www.sciagnij.pl/programy/p/Gry-Narzedzia_i_dodatki-Patche-The_Witcher_Patch/8902/1

• Unable to start XP in safe mode, stuck at mup.sys; BSOD with installation disc

  My computer is a computer laptop Asus eeePC 1000H with no material changes and default OS. I left the machine all night and came to see the machine with the error text:

  "Reboot and select proper boot device."
  "or Insert Boot Media in some boot device and press a key.

  Restart in safe mode gave me the same error, except that I could see that the boot process failed at mup.sys.

  Then I tried to repair my installation by using a Windows XP installation disc so I could use the Recovery Console, but I got a BSOD and error:

  STOP 0X0000007E (0XC0000005, 0XF75DE0BF, 0XF7A2A208, 0XF7A29F08)
  PCI.sys-address F75DE0BF base at F75D7000 Datestamp 3b7d855c

  I have turned off unnecessary equipment in the BIOS and still have the same result. The next step here is to erase completely the machine and retemplate TI - something I'm eager to avoid.

  I've been surfing on support forums all morning and I noticed that there is a spike in people with this problem. Is there a virus going around or was there a windows update last night? I use McAfee if it makes a difference.

  From your description of the problem, it sounds like the hardware failure, no software (virus). First test the drive and RAM. Since you don't have a CD player with eeePCs, you need to use bootable USB based on keys of an external optical drive or troubleshooting tools. Or, if the computer is under warranty, contact Asus support.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  If you can not do the test yourself and/or are uncomfortable opening your computer, take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad).
  MS - MVP - Elephant Boy computers - don't panic!

• Get a * next to a required field which has required but not marked (edition in HTML mode)

  I have a form that required the phone number field, but it is not marked with a * like the others.

  I went through the code and cannot find differences between required fields and optional fields.

  I use the HTML mode, it's what I use, so all advice is appreciated. Thank you

  HTML5:

  * Phone:

  necessary' > '.

  Nancy O.

• Lightroom for Mobile (iOS): download in the background (edit in offline mode) is not available?

  Hello

  iOS automatically to lock in iPgone every 1-5 minutes under the security. Download a collection seems to not work while this is happening, and this is why the download stops. This means that the function is unusable for any collection of more than 20 photos.  I checked the list of the background Refresh Apps and Lightroom is not in it and thus confirmed the team of support via chat. Does anyone know of a workaround in iOS?

  Thank you

  Marcos

  It's not under the general apparently (can't trust Google for the right answers?)

  A visit to the Apple Store produces these results.

  Settings > display & brightness > Auto-Lock