eMac 1.0 Ghz ATI speaker Grill Removal

Similar Questions

• My laptop speaker grilled

  Hi all

  My laptop is a HP Pavilion g6-1220SA and it is old about 2 yearls.

  On Saturday, I was editing some videos and playback, heard a noise grinding, which was followed by a black smoke coming out of the vent to the left speaker.

  I have the PC off, removed the battery and left for a while. He had a disturbing burnt plastic smell.

  Today, I took the time to disassemble the laptop (Kudos to HP for the provision of comprehensive manuals) and it seems to me that the only thing that is not OK is the left speaker, which seems burned.

  My questions on the forum, before taking the machine to a repair center are:

  (1) what are the causes involved burn like that?

  (2) it is likely that something is wrong with your laptop and the burning speaker is a symptom rather than the main problem?

  Photo linked here:

  

  Finally, I see that the speakers are connected by a pair of white wires and reading that is soldered in. If I remove a speaker, I have to get out them both. If I do that, I will always get the 3.5 mm headphone jack sound?

  Thank you!

  @NP_Lima

  Hi all

  I replaced the speakers and the situation seems to have returned to normal.

  Later in the day, I again heard the creaking sound from the left speaker (even I heard before she grilled), all using Windows Movie Maker. I immediately cut the PC.

  I plugged in the headphones and found that the noise was there as well. My conclusion is that something has been the cause of the problem before the sound reached speakers/headphones. I decided to re - install the audio drivers.

  Previously, I had the IDT HD audio drivers. I uninstalled them and when the PC came back on the standard audio driver of Windows 8 is currently in use. I have no problems in the days that followed.

• Part number for the T400s left speaker grille?

  The grid on the left side of the keyboard on my T400s has fallen - and I can't find same what is the part of that number?

  45 2656 M which is the reference number of the entire scope of keyboard you need to get in order to get a new grille left speaker. (This includes other pieces as well, and I imagine you would cost a bit to get to replace)

  http://www-307.IBM.com/PC/support/site.WSS/MIGR-72793.html

  listed in the link above.

• Something stuck in the speaker Grill.

  Have anyone of you had this happen and what is the best way to remove this?

  I find that a toothbrush soft hair works very well if canned air is not.

• Is there a slot for SD card for an emac (2005)?

  Hello. I recently bought an apple eMac (1.42 GHz model 2005). I recorded a few images from a video camera and I wanted to import images into imovie. However, it seems that there is no card slot SD on the eMac. Help!

  Computer name: eMac

  Machine model: PowerMac 6.4

  Processor type: PowerPC G4 1.5

  Number of processors of: 1

  Processor SPEED: 1.42 GHz

  L2 cache memory: 512 KB

  Memory 2 GB

  Bus speed: 167 MHZ

  Boot ROM version: 4.9.2f1

  Serial number: G8 * CSC

  < personal information under the direction of the host >

  N ° MADT doesn't have an SD card slot.

• ATI error and no windows - Satellite Pro A60

  Hello

  When I start my computer, I get a blue error screen c0000415
  A quick google reveals that this is one of these: http://support.microsoft.com/kb/832324

  "So what are you bothering? I hear you cry - the problem I have is, in getting this error of the other (also the ATI card based) I stuck my red disc in and erased everything - including the windows... and CFLA error occurs before windows installs and SafeMode (-that worked perfectly before) does not work because windows is not installed!

  Oh the fun.

  "I think it's a hardware error" - Yes so don't I... However, before the reinstall and get it back, I could work to the computer in safe mode and videos played very well with the resolution and full color. Am I missing the point if I think a video work is an indicator of a working video card?

  I admit that I'm perplexed indeed. I'll try to dig up an old Windows 98 drive, but I don't know how much this will help, because the only copy of XP I have is on the recovery disk... [Return to step 1]

  Any suggestions much appreciated - thanks in advance...

  [it's a satellite pro A60 w / 256 +?] RAM, processor celeron 2.8 Ghz, ATI Mobility Radeon 7000 etc...]

  Hello

  As suggested in document of Microsoft this problem can occur if an ATI Radeon 7200 graphics card has been installed on your computer and the driver that is supplied with this adapter may not work correctly with Windows XP.
  The installation of SP2 should help.

  This statement of Ms. says it all! It of not a hardware problem but it is a compatibility issue with Windows XP (without SP2) and the driver radeon ATI 7200.

  You should try to get an original CD of Windows XP with or without SP2.
  The software callednLiteallows you to create a Windows clean boot CD and add the patches MS and service packs for this CD.

  Then, you can try to boot this CD and after installing the OS, you need to update or change the graphics driver!

• EMac G4 Desktop disappearance!

  Firstly apologies to the Mods if wrongly placed wire box: don't know if the problem is OS X or the hardware itself. Please move as you wish.

  The computer is a very, very gently used g4 emac 1.42 ghz, 2 GB ram. HD has 25 GB 79 gb free space. OS X 10.4.11

  Last week my personal office froze on a few occasions that require a start/stop hard - never saw this before. While working, I checked and repaired the disk and permissions of the drive just to be sure. Past.

  On the next day to have no office; just a clear blue screen with a mobile cursor. No menu. Nothing to select. No "BONGS", no unusual sounds of HD, no rattling or complain - just not pale blue screen.

  Stopped and restarted in 'safe' mode '-all right; eMac works very well but with the limits of normal "safe" mode

  Q. where is my office, how can I access it once again, will be what happened to my personal office also reach the mode 'safe '?

  A lot of reading later... things I've done:

  OS X Tiger DVD starting > disk utilities > repair and check the disc and new permissions > some corrections needed and done > PASSED.

  Still cannot start the office staff.

  Use of external HD and Macbook Pro core i7 with intention to start test eMac Tiger OS X on an external drive and perhaps clone off existing eMac material before wiping and new OS install acquired.
  Have deleted and partitioned Touro EHD on both eMac and Macbook Pro, as 1 Partition and Apple Partition map and then using OS X DVD tried to load on Touro. Won't - implements the error message saying OS X is 4.7 GB and there is not enough free space on selected external hard drive. There are 499 GB free!

  I don't know how plu eMac lasts and I can't remember what to do for the better – I am a week older and not further on...

  Any help would be appreciated massively. Thank you.

  macludite

  Hello

  Looks like the drive to install 10.4 pre - 10.4.6, which does not include 4096 sectors of the new Advanced Format of Byte.

  I would start safe mode & try your current install the external disk cloning... most eMacs can boot from USB drives into the ALT on startup.

  My Notes on the secure boot thing, bolded the 2 biggest suspects...

  One way to test is at the start of the HD, (now shift key at startup), run utility disk in Applications > Utilities, then highlight your reader, click on repair permissions, test for problem in Mode safe...

  PS. secure boot can remain on the gray radian for a long time, let go, he's trying to repair the hard drive & trash/rebuild the cache files

  Reboot, try again.

  If she does only regular boot, then there might be a hardware problem as Video card, (Quartz is disabled mode without failure), or the airport, some USB or Firewire devices, or the module in part 3, Check System Preferences > accounts (users and groups in later versions of OS x) > login items window to see if she or something relevant is listed. Or a stray process eating RAM.

  Check system preferences > Other Row, for the 3rd part Pref panes.

  Also look in these if they exist, some are invisible...

  / private/var/run/StartupItems

  / Library/StartupItems

  / System/Library/StartupItems

  / System/Library/LaunchDaemons

  / Library/LaunchDaemons

• speaker cleaning Z580

  Z580 15.6 "

  There is little to dust in the holes of the speaker thingy, in that the home theater dolby speaker Grill

  Is there a good way to clean without damaging it?

  should I just use a needle? the holes are very small.

  He could not find in the manual on this subject.

  
  

• WARNING: The Catalyst Control Center is not supported by the version of the graphics adapter driver you activated. If you please update your ATI graphics driver or enable your ATI card using the display manager.

  Original title:  Install the new NVIDIA GeForce GT 240 graphics card but now gets error message regarding the necessary to the old card drivers ATI Radeon.

  I just bought a new computer from AMD PHenom II quad core Dell Inspiron with Windows 7 installed. For the graphics card, an ATI RAdeon 4200 on it there but I wanted a more powerful card and installed a NVIDIA GeForce GT 240 graphics card. The ATI Radeon is not delete because honestly, I could not recognize what it should look like and thought that maybe it was incorporated. The fine installed NVIDIA card and now shows as the graphics card used by the computer Information System.

  My problem is that whenever I start my computer, I get an error message saying that the drivers for the ATI card are not compatible with the Catalyst Control Center. I think I need to disable the ATI card, but don't know how. Can you help me?

  Dell Inspiron 570 is a desktop computer, the ATI Radeon 4200 is an integrated graphics card chipset usually equipped with laptops. Something is not here.

  Go to dell support, enter your tag # and get the origonal system specifications.

  You can uninstall anything about ATI through Add/Remove dialog

• Only, secure boot no noise or airport

  eMac 1.42 GHz, 1 GB RAM, PowerMac 6.4 Power PC G4 HD 150 GB, 2005.

  The machine has been lying idle for a month or two, and when I shot a few days ago it has initialized a blue screen, no 'start Mac OS' progress bar and then it turned black and had to be put off.

  Boots in mode without failure only and start clone on Firewire drive or internal startup disk. Boot to the original installation disk so I used disc utility it for startup disc - no problem found - check and repair permissions.

  What I tried:

  * replaced the 3.6V battery backup - had fallen less than 1V - and reset the PMU.

  * Reset PRAM, as well as the NVRAM using the commands from the terminal after the start of the command Option o f. When it restarted it again was the blue screen.

  * has started in single-user mode and made fcsk - fy who finds nothing wrong with the startup disk.

  * also in Single User mode makes the sh/etc/rc to start and stay in mode command KNEW that showed a lot of info. What caught my eye in particular was 'Boot Cache Control - could not start resource busy cache' and ' Boot Cache: cache init failed. " In addition, more far down was a whole bunch of errors mDNSResponder saying ' ERROR unknown opt 4 ".

  In safe mode, preferences / system says 'No output device found' and the sound effects are grayed out.

  In System Preferences / network is not airport, while the airport was previously working on an Airport Extreme card.

  Configuration of the airport said 'no Airport card not installed' even if it is installed and working a few weeks ago.

  In Audio Midi, it says output and input not supported, as well as "default of output - no" and the same for the entry. However, the commissioning of the chime so the speakers must be OK.

  All this means that the video card has gone kaput? I don't know much about the technical side and how he knocked out the sound and startup functions. Looking for lights.

  I had this eMac for 10 years or more and it was mainly used for browsing the Internet and some audio and iMovie but nothing very heavy editing. Also for Appleworks 6 occasionally. Wouldn't want to throw away.

  The most convenient airport is disabled in earlier versions of Mac OS x Mode without failure.

  A few things to try...

  Remove the RAM and clean the contacts with an eraser, reinstall the RAM.

  He starts in Open Firmware with CMD + Option + o + f?

  http://docs.info.Apple.com/article.html?artnum=42642

  Reset-nvram (press enter)

  Configure default (press enter)

  Reset-all (press enter)

  Did you do a reset PRAM, CMD + Option + p + r...

  http://support.Apple.com/kb/ht1379

  Indeed, to make 3 in a row, takes a bit of time.

  Boot portfolio alt or option key, let it sit on the screen of choice to start for a few minutes to warm up before selecting the disc of Lout.

• Strange black screen problem Inspiron 1526

  Dell Inspiron 1526 - Windows Vista Home Premium (32 bit) - Service Pack 2 (problem started all with SP1) - AMD Turion (TM) 64 X 2 Mobile Technology TL-60 2.00 GHz - ATI Radeon X 1200 Series

  This is probably the strangest problem that I've never seen or heard of.  I've owned this phone for about a year and a half without any problem, then one day, I decided to put my computer into sleep mode by closing the lid (I've done several times before without problem.).  When I lifted the lid, the computer woke up, but the screen refused to show.  Thinking it was an easily solvable problem, I restarted the computer.  The computer turned on, but the screen was black.  After having turned the computer works enough times (probably 20), finally displayed screen and the error message say 'RTC Mode Fixed.  Date and time can be wrong. "I couldn't help but think"What the... ". "I ran into my share of issues of computer before, but nothing as weird as this.

  Assuming that everything was fine, I let the computer start normally and shortly after the BIOS, the computer screen suddenly turns off.  The only way I could get the boot sequence to pass the BIOS screen and start normally, I had to remove all the devices (including the power cord.)  After the computer has finally loaded completely, I was able to function normally.  Almost every time that I cut it however, the black screen problem happen again.

  A solution will be greatly appreciated.

  If you still experience the problem, or if you arrived after doing a search for the same problem with your Inspiron1526 (or other). The solution is to replace the CMOS battery. There was some problems with the connector of the screen becomes loose, but if reinstalling the display connector does not solve your problem, then the battery is dead.  The Mitsubishi CR2032 batteries from CHINA are down less than 1.5 volts in only 1-2 years. Looking at the battery that looks like they're a cheap copy of bootleg and probably not at all Mitsubishi. They all have the "Made In CHINA" stamp on the bottom edge. Unfortunately to get to the CMOS battery, you will need to disassemble the laptop computer entire almost to have access, but by replacing the bad battery with a reputable CR2032 3 v battery will solve the problem. After the first reboot, you need to give time for the BIOS to reconfigure and you need to reset the time system and date but the laptop will resume its normal operation after that.

  Unfortunately many calls to Dell technical service gave no help to this problem either. Technicians have even claimed to have no knowledge of what the CAPS and the blinking NUM LOCK lights meant. If you are lucky, you may be able to restart a couple times before the laptop doesn't start is not at all, but the time system must be reset - if this happened to you, it's a dead giveaway that the CMOS battery is about to fail. Once you hear the voltage of the battery drops to initial power engage readers and the fan will run for a few moments and then the unit will completely disable. Nothing appears on the screen.

• Intel Chipset and USB drivers won't install properly - no equivalent for Windows 7?

  Compal CL51
  2 GB RAM
  32 bit Dothan CPU Intel Pentium M clocked at 1.8 GHz
  ATI Mobility Radeon 9700 graphics card
  100 GB HD
  Windows Experience Index: 3.4

  I was able to install Windows 7 Pro on my CL51 compal without any apparent hitches, except these:
  Intel (r) 82801DBM LPC Interface Controller 24CC
  Universal host controller Intel (r) 82801DBM USB 24 4

  In addition, the function keys volume control does not even if the function for dimmness keys work. Maybe it is something chipset - I don't know because there is no other broken/alerted devices in Device Manager.

  The LPC just shown as an unknown device without no driver interface. I sailed on the drivers from update-> Let me pick-> see her-> everything surfed down for intel and the LPC interface. To paraphrase, he said that it was "not guaranteed to work with System 7. Are you sure you want to do this? Your system might break. "I did anyway and now it manifests, but I don't know its proper operation, although he says he is.

  The USB thing pops up, but then when I unplug the device that seems to use it (TrendNet Clearlink for Skype - model TVP-SP2) you get a triangle of yellow alert on Device Manager. It does not recognize when I plug it in. When I look at its properties in Device Manager, I get this in the status of the device: "Windows has stopped this device because it has reported problems. (Code 43) ». There is no "troubleshooting."

  The windows supports 43 page Code issue is unnecessary, pointing vaguely to the manufacturer of the device or intel - I can't be sure. (http://support.microsoft.com/kb/310123)

  Code 43
  Recommended resolution

  One of the motors controlling the unit notified the operating system that the device has failed in some way.

  If you have already run the Troubleshooting Wizard, you can view the documentation for the hardware for more information about diagnosing the problem.

  The only "documentation" that accompanies this was a quick start and user guide. It works halfway. It stops working correctly, and you end up having to reinstall the drivers if you unplug the unit. Every time.

  The closest I can understand, I need Windows 7 support for all the things Intel 82801DB/DBM on my computer. The Intel site is too vague in it's style of support for downloads. I couldn't tell what to download, or even if I had the right to download.

  As for the thing of volume of service - I am used to use it in Windows XP. I would of course only it in Win7.

  If anyone has any suggestions as to what to try next, I would be grateful.

  Thanks for the replies. I went on the Intel site.

  I downloaded the chipset from the Intel site identification software. I discovered that I have a 855 Chipset of the PM. Then, I got on a chat session with the Intel Support cat.

  The short of it is that there is no way to upgrade to this chipset regarding Windows 7 for Intel.

  The transcript of the conversation:

  Intel: Hello. Please use the Customer Support chat service. We are pleased to be of service. How can I help you today?
  you: I have a laptop CL51 compal, which uses the game of 855 PM chips, depending on the software of the identifier, I downloaded Intel. I need Windows 7 drivers, but they are not available for Win7 in the download area of support for this chipset. What can I do?
  Intel: I apologize, but there are no drivers available for this operating system or Microsoft * Windows * Vista *.
  you: when will they be available?
  Intel: My apologies, but this controller has reached its end of life there will be no new updates for new operating systems software
  you: I now have windows 7 running on the computer. It seems to work fine, except that one of the device drivers come with the yellow triangle. I can do everything I have to except the function keys are not express of adjusting the volume (volume up and down with function keys). How crucial the chipset is correct for a functional system?
  Intel: This new operating system must have all the required software for this chipset work, so it should be good, but with limited capacities
  you: Control Panel-> Device Manager-> other devices-> unknown device-> properties-> "the drivers for this device are not installed. (Code 28) There is no driver selected for the item or a set of device information. To find a driver for this device, click Update driver. »
  Intel: excuse me, but we would not know what device means the Device Manager, this chipset was not intended, and it is not tested for Microsoft * Windows * 7, at this point, you can use this operating system at your own discretion
  you: Yes, I thought. However, when I go to the dashboard-> devices and printers-> laptop-> Trouble Shoot it seems to think it is called Smart@IO. Is something Intel?
  Intel: He doesn't seem to be a controller of us
  Intel: You may need to verify with the laptop manufacturer to see which devices are installed on this system
  you: under control panel-> Device Manager-> other devices-> unknown device-> properties-> general it is said "location: on Intel (r)" 82801DBM LPC Interface Controller - 24CC "»
  you: this seems Intellish.
  Intel: This is part of the chipset controller, but as mentioned, there is no software for this controller that run on Microsoft * Windows * 7 and this operating system must have the software required to make this mature product to work
  you: so the problem of chipset is not relevant?
  Intel: It seems to be, please keep in mind that you are using a non validated platform
  you: it's the fact that I can't use function keys to change the volume of the sound related to the chipset?
  Intel: Is not part of the chipset
  you: so another driver is required for the volume function keys work correctly, no Intel...
  Intel: OK, most of these devices is third-party components
  you: OK, so if I don't use the chipset, what exactly he controls?
  Intel: He will take care of i/o control for USB devices
  you: Okay, that might be the reason why I can't get some USB HID devices to work. Anything with compatibility Win7 looks good, however.
  you: I tried a TrendNet TVP - SP2 ClearLink Skype speaker. It works fine on other systems. Just not this one because of the thing at the end of life on end of Intel. It is likely that if they have a Win7 compatible driver I could operate or I'm stuck here?
  you: it works still fine on new lenovo to my wife with Vista.
  Intel: You may need to verify this issue directly with the manufacturer of your system with TrendNet
  you: my system manufacturer is probably going to tell me that it is an end of life issue - referring me you Intel - but I bet you knew that already huh? . I'll check with TrendNet to see if they can build a new driver for Win7. Thank you. This clears up a lot of things. Hard drives seem to work well. Other USB devices work as well, especially if they are sized to work with Win 7. Once again thank you. Happy new year.
  Intel: You're welcome.

• SPDIF out on Compaq CQ40-122AX

  I have a Compaq CQ40-122AX, running VISTA home basic sp1.

  There IDT High Definition Audio built in and a HDMI output. He also says that it will be an available SPDIF output using a HP/Dock. Now, I'd like to use the SPDIF output, but I am reluctant to by the docking station for £200 as advertised on amazon. In the options for the Soundsetup there is a definition available also SPDIF.

  IDT HD Audio Codec driver version: 1.0.5934.0

  For IDT HD Audio DEVICE driver version: 6.0.6000.16386

  Only the input/output Audio/video are:

  VGA

  HDMI

  Headphone 3.5 mm

  Microphone 3.5 mm

  I had a browse autour and found that some HP models spdif output available via the Jack 3.5 mm as optics, when the adapter is plugged it activates an LED inside and that it moves the optical signal to the Toslink cable.

  Adapter cable and optical at Maplin

  My question is, the SPDIF is accessible on my model of laptop CQ40-122AX with this configuration without the HP docking station or could there be another way? Since there is not in there, it must be possible to access it somehow, and the docking station just seems too expensive to make sense.

  Look forward to hearing responses.

  Message edited by Sven on 18/01/2009 05:27
  何思凡
  
  Compaq CQ40-122AX, Vista Home Basic 32 bit, AMD Athlon x 2 1.9 Ghz, ATI Radeon HD3200, 1 GB of RAM,
  
  -Each one favor Post back your results, resolved or not - LET BRAVO!

  No solution is presented using computers laptops, built in the ability to use SPDIF for DD and DTS streams. The only solution that I found satisfactory is the external soundcards next via a USB port.

  I use the product bought in Hong Kong, works well with XP and Vista, that's what I tried ebay. The least expensive solution to the s/PDIF output, I found. It is an optical output.

  http://CGI.eBay.co.UK/5IN1-USB-6-channel-PCI-external-moveable-5-1-sound-Card_W0QQitemZ220338593076QQcmdZViewItemQQptZUK_Computing_ComputerComponents_SoundCards?hash=item220338593076 & _trksid = p3286.c0.m14 & _trkparms = 72 %3 A 1300 | 66 %3 A 2 | 65 %3 A 12: 39 %3 A 1 | 240 %3 A 1318

  http://www.Google.com/products?complete=1 & hl = in & q = USB + to + Converter + SPDIF & um = 1 & ie = UTF-8 & his = X & OI = product_result_group & resnum = 5 & CT = title

• Need Satellite C670D - 115 serial number and model number

  Hello!

  I need your help.

  I have this laptop Satellite C670D - 115 PSC4AE.
  I changed mothearboard:

  _Dead we: _
  Old mothearboard: H000036160 WK1145
  1.70 BIOS version
  E300 CPU 1,3 Ghz
  ATI Radeon HD 6310, with this one:

  New Mothearboard: H000036160 WK123
  Version of the BIOS 1.90
  TREATMENT E300 CENTRAL UNIT
  ATI Radeon HD 6310

  You can my serial number of wath I have?
  Number of room etc.
  I used programs Aida 64 bat not to watch.

  Value of the field
  Computer
  Computer Type PC ACPI x 64
  Microsoft Windows 8.1 operating system company
  Operating system Service Pack-
  Internet Explorer 11.0.9600.16384
  DirectX DirectX 11.0
  Name of the computer
  Username
  Field of connection
  Date / time 2013-10-26 / 09:55

  Motherboard
  Type of processor DualCore AMD E-300, 1300 MHz (13 x 100)
  Card mother name Toshiba TKBSB
  Card mother Chipset AMD Hudson-1, AMD K14
  System 5741 MB (DDR3 - 1333 DDR3 SDRAM) memory
  DIMM1: Samsung M471B5273CH0-CH9 4 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
  DIMM2: Samsung M471B5773CHS-CH9 2 GB DDR3-1333 DDR3 SDRAM (9-9-9-24 @ 666 MHz) (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz) (5-5-5-14 @ 380 MHz)
  Type of BIOS FRIEND (24/05/2012)

  DMI BIOS vendor American Megatrends Inc.
  DMI BIOS Version 1.90
  TOSHIBA DMI system manufacturer
  DMI system product TKBSB
  DMI system version for O.E.M.
  DMI system serial number to fill O.E.M.
  DMI Motherboard manufacturer PEGATRON CORPORATION
  DMI Motherboard product TKBSB
  DMI Motherboard Version 1.90
  DMI Motherboard serial number BSN12345678901234567
  TOSHIBA DMI chassis manufacturer
  DMI chassis version has vacancies O.E.M.
  DMI chassis serial number CSN12345678901234567
  DMI chassis Asset Tag is no inventory number
  DMI chassis Type Notebook

  Display
  Graphics AMD Radeon HD 6310 Graphics (384 MB)
  Graphics AMD Radeon HD 6310 Graphics (384 MB)
  AMD Radeon HD 6310 (wrestler) 3D accelerator
  LG Philips LP173WD1-TLN1 17.3 "LCD monitor

  What family laptop I have? C670/675/680?

  Thank you very much and good day!

  All data you need you can find on Toshiba label located on the bottom of your laptop. You will find the serial number of your laptop. We cannot tell what you have the serial number.
  Model number is C670D-115 and your laptop belongs to the family of C670D. All models with D are AMD chipset models.
  Part number is PSC4AE-01100xxx. It depends on the country where your laptop has been purchased.

  That's all that I can say about it.

• Microphone does not work with Siri

  Hello

  I'm having some trouble using Siri on my iPhone 6 more 164 GB model (AT & T).  When just using the microphone Siri does not hear my voice.  I tried the following troubleshooting steps.

  • Power recycled
  • Hard reset
  • Micro works with other apps: voice commands, voice memos, phone calls, Shazam
  • Turned Siri works
  • Siri works with the headset supplied with my phone and my Bluetooth headset
  • Port of cleaned Microphone and 3.5 mm port
  • iOS is updated 9.2.1

  Any help is appreciated.

  Your phone has three microphones. Siri works with your microphone facing forward, who is behind the earpiece speaker grille. To test the microphone, record video using your camera facing forward. See if you have any audio during playback.