Encryption advice please WRT160N router/gateway/modem wireless

Similar Questions

• Static route ISA570W to Comcast gateway/modem

  In my view, that it is a question of static route.

  I want to be able to connect to the gateway/Modem Comcast (10.1.10.1) using any computer on my network. Currently, I am unable to do this, I am also unable to ping the unit of Comcast. Here's my setup.

  Comcast device (SMC8014)

  WAN IP: 50.x.x.238

  LAN IP: 10.1.10.1 (255.255.255.0)

  A single cable CAT5E for:

  ISA570W (WAN Port) - (basic out-of-the-box configuration, 1 - WAN, DMZ - 1, 8 - LAN Ports)

  WAN STATIC Port info:

  IP WAN: 50.x.x.233 bridge (255.255.254.0): 50.x.x.238

  LAN IP: 10.1.10.2 (255.255.255.0)

  DHCP enabled for bridge VLAN-1 (10.1.10.30 - 99) by default: 10.1.10.2

  A single cable CAT5E for:

  Cisco SG200 - 50 p (POE switch to serve as a connection for phones and desktop computers)

  LAN IP: 10.1.10.3 (255.255.255.0)

  For devices on my network to get an IP address from the device of the ISA, ISA is also the default gateway. I have logged on to the device of Comcast and all firewall rules and blocking are disabled.

  Here's a copy of my current routing table according to the ISA570:

  Destination address	Subnet address	Entry door	Flags *.	Metric	Interface
  192.168.3.0	255.255.255.0	0.0.0.0	U	0	DMZ
  10.1.10.0	255.255.255.0	0.0.0.0	U	0	DEFAULT
  10.1.1.0	255.255.255.0	0.0.0.0	U	0	VOICE
  192.168.25.0	255.255.255.0	0.0.0.0	U	0	COMMENTS
  50.x.x.0	255.255.254.0	0.0.0.0	U	0	WAN1
  127.0.0.0	255.0.0.0	0.0.0.0	U	0	LOOPBACK
  0.0.0.0	0.0.0.0	50.x.x.238	UG	0	WAN1

  My desktop (10.1.10.32), so I'm unable to ping or you connect the unit to comcast to 10.1.10.1.

  So according to me, that missing me something simple here, it is a solution of static route, or I'm looking for policies of NAT?

  Thanks for your help and please let me know if you need more information on my network.

  -Matthew-

  OK, a few possibilities here.

  1. Did you go through this process for the SMC8014 Bridge mode?
     • http://www.handymanhowto.com/2011/08/19/how-to-configure-a-Comcast-business-class-static-IP-address/
  2. I advise to use a different subnet on the LAN of the ISA to the 10.1.10.x interface.  The reason is that when you send a request from a subnet of 10.1.10.x behind the ISA to a subnet of 10.1.10.x, your PC and the ISA assumes that the device is on the same network and will not try to route.  Consider using the subnet of 192.168.75.x by default on ISA LAN interface.

  If you do not step 1 above, then I'm fairly certain that you will not be able to browse the internet at all.  If you can browse the internet, but just can't get the Comcast router 10.1.10.1, then chances are 1 step has already been completed.

  Shawn Eftink
  CCNA/CCDA

  Please note all useful messages and mark the correct answers to help others looking for solutions in the community.

• WRT160N router broadcasts not Internet

  Hello

  I had a Linksys WRT160N router for about 7 years and recently started having a few problems with it. I guess it is old and needs to be replaced, but before I got up to get a new one I wanted to check.

  The connection displays the full bars, but gives the error that there is limited internet access. I am still in the same room with it when using the computer, did sit no more than 5 to 10 feet away. When I plug my computer directly into the modem, then there is no problem, that's why I'm assuming that it is the router. I tried to look for similar problems in the forums, but if I missed the appropriate thread, I'm sorry in advance. Also, I'm not sure what information would be required to solve problems so I'll add some to start basic info:

  Description: Intel (r) brand double wireless AC 3160

  DHCP enabled: Yes

  IPv4 address: 192.168.1.1

  iPv4 subnet mask: 255.255.255.0

  IPv4 Default Gateway, DHCP server, WINS Server and DNS server are all: 192.168.1.100

  Thanks in advance,

  Liz

  You have tried all the steps and I would say that the router has served you well. I think that now is the best time to upgrade to the latest model.

• Why my ipad loses the wifi connection when I abandon my modem wireless of Qwest

  Why my ipad loses the wifi connection when I abandon my modem wireless of Qwest

  WiFi connections are losing their strength increases the distance between the router and so as a general rule, there are some conflicting objects

  Try the following steps please

  The following actions and after each test to see if the issue is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  4. Settings - WiFi - < network name > - Click on forget network - do a restart forced according to 3 and then add again the network
  5. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  6. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  7. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  8. Backup the device to iTunes - restore as NEW (no) - see if solves problem - if yes - restore backup
  9. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• Problem with RV0042 - mask subnet/router/gateway?

  Hi guys.

  I have a DSL here in Holland. To use my RV042 VPN function, I need the router to get the IP of the DSL modem. No problem, I bought a modem that can define transparant and with dhcp-parody the modem Gets the public ip address (say 85.223.12.34).

  The thing is, I can't access the internet, or in fact any IP that isn't in the first segment of the external IP address. So I can reach 85.123.34.56, but not 86.123.34.56. So I plugged the modem to a computer, set the transparent modem and the computer got the public IP address. And you know, I have a perfect connection, and everything works. Looking at my ip information, download the provider 255.0.0.0 subnet. Im not a Networking Wizard, but it seems to me that the problem lies here. But why is my stand-alone pc able to connect quite normal, but when I connect my linksys RV042 and internal diagnostic test (ping) of the router or a computer behind the router, obtaining an ip address, I don't get anything.

  When I ping manually, I also get the message "network is not available. Ping to an IP on the same subnet (for example, 85.111.111.111) goes perfect.

  I'm obviously missing something here. My colleuge said it could be and router/gateway (currently bridge) or a NAT problem-associated device.

  Please point me in the right direction.

  Intellectual property of addidional information:

  External ip address: 85.223.12.34

  External subnet mask: 255.0.0.0

  External gateway: 217.149.196.82

  External DNS: 217.149.196.6

  Internal IP address: 172.16.0.254

  Internal subnet: 255.255.0.0

  New firmware etc.

  Thank you guys!

  What static routes you add exactly on your RV? It's funny, it works now.

  WIndows seems to accept a gateway address that is not on a connected interface.

  The first line is the rule of default gateway:
  0.0.0.0 0.0.0.0 217.149.196.82 85.223.66.38

  The second line just tells you that 85.0.0.0/255.0.0.0 is connected to the ethernet adapter that has the IP 85.223.66.38.
  85.0.0.0 255.0.0.0 85.223.66.38 85.223.66.38

  Technically, the first route should now work. There is still no route for 217.149.196.82 in the routing tables. The only route that matches the destination IP 217.149.196.82 is the first route.

  But I guess that, in your case, that default gateway with 217.149.196.82 is actually connected to the network on the side of the VP, i.e. your ISP WAN runs two IP subnets on the same network. Since this first route runs on Windows, I guess that WIndows simply tries to find the MAC address of the 217.149.196.82 on the WAN using ARP interface (i.e., it assumes that the device with 217.149.196.82 is directly connected to the WAN Ethernet) and if something is used as default gateway. Is not really consistent with the ideal IP routing, but still works...

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• My MacPro will not start. I get a gray and white screen. Continues to try to restart, but never done! Advice please.

  Care of my MacPro is lower from a previous post.  It does not start, but keep train.  I get the rope to music if I stop and start again.  Advice please.  Thank you very much.  Allan

  Material Information: ℹ️

  Mac Pro (early 2008) (data sheet)

  Mac Pro - model: MacPro3, 1

  2 3 GHz Quad - Core Intel Xeon processor: 8 strands

  8 GB of RAM expandable

  DIMM Riser B/DIMM 1

  1 GB DDR2 FB - DIMM 800 MHz ok

  DIMM Riser B/DIMM 2

  1 GB DDR2 FB - DIMM 800 MHz ok

  Riser DIMM A/DIMM 1

  2 GB DDR2 FB - DIMM 800 MHz ok

  Riser DIMM A/DIMM 2

  2 GB DDR2 FB - DIMM 800 MHz ok

  DIMM B/DIMM Riser 3

  1 GB DDR2 FB - DIMM 800 MHz ok

  DIMM B/DIMM Riser 4

  1 GB DDR2 FB - DIMM 800 MHz ok

  Riser A/DIMM DIMMS 3

  Vacuum

  Riser DIMM A/DIMM 4

  Vacuum

  Bluetooth: Old - transfer/Airdrop2 not supported

  Wireless: en2: 802.11 a/b/g/n

  Video information: ℹ️

  NVIDIA GeForce 8800 GT - VRAM: 512 MB

  HH281 1920 x 1200 @ 60 Hz

  DELL3007WFPHC 1600 x 2560

  System software: ℹ️

  OS X 10.10.2 (14C109) - since the start time: 20:27:26

  Disc information: ℹ️

  ST3320820AS_P disk0: (320,07 GB)

  EFI (disk0s1) : 210 MB

  Disc 1 - system (disk0s2) /: 319,21 GB (17,69 GB free)

  HD (disk0s3) [recovery] recovery: 650 MB

  WDC WD5000AAKS-41YGA0 disk2: (500,11 GB)

  EFI (disk2s1) : 210 MB

  System install disks 1 and 2 (disk2s2) / Volumes/installation discs for systems 1 & 2: 16.11 GB (4.40 GB free)

  Disc 2 (disk2s3) / Volumes/disk 2: 483,52 (291,34 free go-go)

  Hitachi HDS721010DLE630 disk1: (1 TB)

  EFI (disk1s1) : 210 MB

  3-1 TB (disk1s2) Dist/Volumes/Dist 3 TB: 999.86 1 GB (328,00 GB free)

  USB information: ℹ️

  Prolific Technology Inc. IEEE-1284 controller.

  Hewlett-Packard HP LaserJet P2055dn

  Hub keyboard Apple, Inc.

  Logitech USB receiver

  Apple, Inc. Apple Keyboard

  Apple Inc. Bluetooth USB host controller.

  EPSON USB printer

  Guardian: ℹ️

  Mac App Store and identified developers

  You still have OSX 10.5.8?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk if Lion or higher

  OS X: on OS X Recovery - Apple Support

  Otherwise start from the installation DVD and keep the boot disk

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  Run the Apple hardware test. You will need one of the original installation discs

  Using Apple Hardware Test - Apple Support

  You may have a bad graphics card. The NVIDIA GeForce 8800 GT - VRAM: 512 MB are prone to failure

• is it possible to connect 2 computers 2 different 1 modem wireless routers

  is it possible to connect 2 computers 2 different 1 modem wireless routers?

  Why do you have 2 routers?

  Depends on the design of the modem. It probably only supports a connection. So, you'll probably end up making a wired connection between modem and "1 router" and if you really need a second wireless router, install a wired connection between the 2 routers.

• Windows Vista does not work with modem wireless broadband

  I saw no answer to this problem.  Can anyone help?

  Windows Vista on my DELL laptop at home does not work with my new NETGEAR modem wireless broadband 3 G.  The modem appears in the list of networks, I just errors like: unable to connect, cannot diagnose,... Both devices work perfectly well together when connected by cable but not wireless.  Interestingly, my laptop work, also a DELL but runing Windows XP, works very well with the NETGEAR modem.

  Summary:
  Vista / Netgear wired - work
  Vista / Netgear wireless - does not work
  XP / Netgear wireless - work

  I went through the NETGEAR troubleshooting guide, doing everything from changing the types of security to manually enter the MAC address of the laptop.  I ran to the ground with the NETGEAR support engineers, and they said check with Microsoft.  I am convinced that it has something to do with Vista.  Any ideas?

  Hi jhandcc,

  Please provide the complete error message you receive.

  Step 1: You can follow the steps described in the article below

  Error message when you try to automatically connect to a wireless access point that uses authentication of network shared in Windows Vista: "Windows cannot connect to" " "»

  http://support.Microsoft.com/kb/948180

   

  If the problem persists,

  Step 2: Download and install the latest service pack for windows vista on the computer

  How to obtain the latest Windows Vista service pack

  http://support.Microsoft.com/kb/935791/

   

  Reference:

  You cannot connect to a wireless network on a Windows Vista-based computer

  http://support.Microsoft.com/kb/935222

   

  For more information, see the link below

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Let us know if this helps

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Update Verizon iPhone 5 new IOS 10 problem: cannot receive/send calls. Shop Verizon says it's an update causing Apple to popular phones to crash all day. Any input or advice, please?

  Update Verizon iPhone 5 new IOS 10 problem: I can't receive/send calls. The store Verizon says it's phones a popular causing update Apple crash all day. Any input or advice, please?

  Don't you say no service at the top?

• Indicator light charging cable does not go on when connected to power what a lack of cable or battery problem? Advice please. I have

  Indicator light charging cable does not go on when connected to power what a lack of cable or battery problem? Advice please.

  Troubleshooting help here > Apple Portables: Troubleshooting MagSafe adapters - Apple Support

• Pitch bend wheel on my pc - 300 midi keyboard Roland. The Modulation part works but when I try to pitch bend a note using the same logic of wheel just plays a continuous note. Can someone give me some advice please? Thank you

  Hi, I have a problem with my pitch bend wheel on my pc - 300 midi keyboard Roland. The Modulation part works but when I try to pitch bend a note using the same logic of wheel just plays a continuous note. Can someone give me some advice please? Thank you

  It's a delicate issue... like some patches cannot stipulate pitchbend...

  But to quickly test your pitchbend wheel actually works properly...

  Download the free lunch monitor...

  Snoize: MIDI Monitor

  Run and see if it sees pitchbend data sent by your keyboard... and therefore by logic.

• My laptop does not recognize my modem wireless of suddenlink cable/wireless.

  My laptop dose not recinise my modem wireless of suddenlink cable/wireless, I had to format my hard drive and I lost the info. for the wireless modem, I tried the KeyCode and it will not reconise the code.

  Hi Richard,

  What is the number and the model of wireless modem?

  You can get in touch with your ISP (Suddenlink) provider for further assistance on this issue.

  SuddenLink Support

• I have a MN700 router for my wireless. How to reset the password?

  I have a MN700 router for my wireless. How to reset the password?

  I contacted Microsoft via the phone, but because they no longer carry this point they couldn't help me.

  Hello

  1. what operating system is installed on your computer?
  2 did you change your computer, after which the issue started?

  Here is the manual for the device...

  http://download.Microsoft.com/download/b/6/9/b69c956c-85d9-4641-aa6f-1548391e0967/mn700_base_station_configuration_guide.PDF

  Reset the router and set it up as if it was the first time. Then, you can simply choose a new password and security settings.

• MG6220 printer must be physically connected to the router to operate wireless?

  Is the need for printer wireless MG6220 be physlically connected to a router to access wireless?

  No, it is connected via radio according to the installation instructions.  The only thread on the MG6220 printer's power cord.

  Installing from the DVD has also updated all programs of Canon and recorded my new printer.  I answered my own question.