EqualLogic Concepts

Similar Questions

• Satellite U300 PSU3DA: error: could not open the file attribute execution of concept maps

  I have a PSU3DA-U300 which I changed from Vista to XP.
  This is because my main computer use will be for navigation (boat) and I was told that most navigation programs will work better with XP. I have almost nothing on my laptop so far, and the system already seems to be slow and freezing too often.

  My question is now on the program of concept maps which I just installed and which does not open. He repeats to me "Eorror: could not open the file attribute.

  What does that mean? I uninstall and reinstall the program, and he comes back with this message.
  I had a glance at the Device Manager, and the only thing that seems incorrect is the PCI memory controller.
  I did a bit of research on this and it seems that this driver is not required for XP? Is this true?

  Would this be a cause of C-Maps program does not?

  Thanks in advance.

  > I did a bit of research on this and it seems that this driver is not required for XP? Is this true?
  Where did you read this info?
  I put t know if the driver is not required, but you get all the drivers on the Toshiba site.

  For your problem with concept maps, I think that it is best to contact you that support the conceptual maps. Here, this is a forum for Toshiba laptops.

• Basic concept of loop PID closed

  Hello

  I have a problem of very basic concept of PID loop closed. I read a lot of material of the PID controller but still confused.

  I understand that the error between the measure and the desired will be processed by PID controller, but I do not understand how the controller output (sum of three P/I/D) set the right plant behand the controller. For example, an electric motor fan will be below on a Board, the force of the wind on the motherboard could be detected by the tension and of course the fan speed could be adjusted by tension. But the error of the setpoint and the process variable will go directly to the fan in Labview without identifying the mechanisms on the plant (fan). I wonder if anyone knows how this error is treated by the plant. And why we need not care about the transfer of the factory function.

  If you have a transfer function for your plants, you don't need PID, because the output of the optimal control can be determined directly from the transfer function! (Well, more specifically, often in this case you would use the transfer to feed-forward control function, which you would combine with PID to correct minor variations between the reality and transfer function model.)

  The output of PID is not a sum of errors. It is a sum of the outputs of regulation - the proportional output, the full output and the derived products output. The gains set the regulator to the specific system, and if they are not chosen correctly, the control will be terrible and potentially unstable.

  In your hypothetical example of two systems - Yes, it is quite possible that one moment the error and so the output will be the same. But if the systems are very different, the next iteration of control errors will be different, so the next controller output value will be different, etc. And if the systems are very different, they should not have the same gains.

• Will the concept AD LDAP Referral supports two different forests

  Hello

  I have areas DomainA under ForestA and DomainB in ForestB. I would like to implement the concept of LDAP Referral for these two areas, so I have set up between these two areas and add a crossRef under CN = Partitions for DomainA and trying to search for DomainB users using ldp.exe DomainA.

  But it seems to not work.

  LDAP Referral Concept is supported in my case?

  I read somewhere that ads supports LDAP Referral for domains that are in the same forest, is this true?

  Can someone help me with this? Please let me know if I am missing any configuration.

  Thank you

  Phani

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Need help for testing and practice the concepts of the server at home

  Original title: Hello team

  I need assistance with testing and to practice the concepts of the server at home... I don't have an option to test laboratory pls suggest possible ways that I can practice... need help... Please help

  Hi Sachinadi,

  You can ask your question in the MSDN Forums: http://msdn.microsoft.com/en-us/hh361695.aspx

  Thank you.

• Concept of possible mobile future

  Watching one of the future videos Microsoft made me come with your laptop new or just interesting or keyboard functionality if they don't completely disappear the way they like to do. The keypad is not a new concept but loose remote sensing or digital technology of skin makes for an interesting combination where the keypad is not visible or locked until you place your fingers on the surface of the keyboard then it not only recognizes the user but also slide the keypad on the side and instantly unlocks not only the keyboard but also the lock on your device screen. Of course touch sensitive technology could be a little better before considering this feature.

  Tablets are also an excellent tool for shopping with. You can view the employees of the item you are looking for a quick glance.<- random.="">

  Hey Kevin,

  Thank you for sharing your future insight and thoughts in the Microsoft community.

  If you have any problem with Windows then post in this forum and we will be happy to help you.

• Michael Kossar: Concept of 32-bit and 64-bit

  I'm Michael kossar, I heard the term 32-bit and 64-bit machine, but what is the concept behind it? Please explain my question.

  I suggest to buy a 64-bit computer.

  Please read:

  http://www.PCAdvisor.co.UK/features/PC-components/3584953/32-bit-vs-64-bit-x86-vs-x64/

  and

  http://www.MakeUseOf.com/tag/64-bit-computing/

  See you soon,.

  J

• M UI concept? Difficulty this please

  In the 6 android title bar height and the height of the navigation bar are smaller than 5 android. But in the concept of sony, it is not changed.
  Small title bar is nice. Very better than android lollipop.
  Someone please tell this to the developers of concept.
  See screenshots. Android 6 5.1 vs android (Google android ui)

  Photos on the left are lollipop, good pictures are marshmallows

  Or give me an official address for the developers and clients of concept

  You can find our Google group + here but to have access to the group you need to have applied and was invited as a tester through Concept of Sony for Android app. You will not have access to the group if you have used other ways to install the software.

• HP Deskjet 3050 AIO a - how to print in concept?

  Could someone tell me please how to print in concept?

  With my other horses, it was possible, but it was by USB, now on WLAN it does not work?

  (see attachment)

  Hello

  Follow the instructions below.

  1. open devices and printer

  2. click on add a printer

  3. click Add a local printer

  4. from the use existing port, select the USB option and then click Next

  5. click the button of Windows Update to get all the support window 7 drivers updated

  6. once the update is complete. Click HP from the menu on the left, then select the printer Deskjet 990c in the right menu, and then click Next.

  7. follow the remaining instructions to complete the installation.

  Once you have the printer added 990c make sure it is the default printer, and then try to print using this driver for the Deskjet 3050 printer. I would like to know if you have the same problem?

• Module Extension Dell EqualLogic Multipathing v1.4 missing setup.pl

  The new v1.4 Dell EqualLogic Multipathing Module of Extension is missing setup.pl script.

  Hello

  Thank you.  A new package is created.  In the meantime, you can try the setup.pl v1.3...   Or use alternative methods to install it.

  Feel free to open a support on this file as well.   They can add you the question open with genius.

  Kind regards

  Don

• My group IP Equallogic rattling of unknown Internet hosts

  Hello

  I have an Equallogic group composed of former members of PS6000 and also running firmware 5.02 (I know it's old).  Our network security team saw that the IP of the Equallogic group sends constant pings to certain IP addresses.  Some of these IP addresses are no. DHCP Server related (169.254.1.151 169.254.1.19, etc.), but also we are seeing pings being sent to internet two IPS, 20.20.20.2 and 20.20.20.3.  These pings are apparently constant, and we can not find in the logs in the management console, why they produce.

  Any thoughts or ideas?

  Kind regards

  Kevin

  Hello

  I suspect that you have a Server Windows, with HIT / me installed.  But the MPIO configuration wizard has not been run to exclude all non-iSCSI subnets.  If the hosts are trying to log on by using all available subnets.  To ensure than a back road, the table first ping this IP address.  In case of failure it will not attempt a connection.

  Then once you run the Remote Setup Wizard, you will see the option of MPIO.  Make sure only the iSCSI subnet is included and this should solve your problem.

  Re: Firrmware.  Very old firmware.  If you run VMware ESXi, you are also at risk of corruption of VMFS metadata.  The minimum EQL firmware to address this problem is 6.0.7.  There are also a lot of improvements to the management of disk errors, etc...   5.0.2 is released Oct. 2010.

  Kind regards

  Don

• EqualLogic PS4100 with a red light.

  Hello

  We have a very old EqualLogic PS4100 with a red light a remote site (connected to a production server and works very well)

  Admin has already left, and we do not have its IP management or identifying information.

  I have someone on site who can provide remote hands.

  Can I connect a laptop and get or does dell provides support paid for it?

  Thanks in advance

  Hello

  the management is optional and it may not be configured. So check your host what address he used for iSCSI to table connection and try a browser with http:// or a ssh client and see what happened. You need java installed to get the GroupManager that run in the browser.

  If you do not get a response that is active and sound using a different subnet in regards to the Storage (iSCSI).

  The user is called "grpadmin. If you do not have a password try "grpadmin.

  If you hands away you can connect a serial cable to the module active controller with parameters 9600,8,1, n in your terminal program favorite (we often use PuTTY). You also need user and password.

  Concerning
  Joerg

• OpenStack on Equallogic

  You have the list of Openstack on Equallogic compatibility matrix?

  I want to know the recommended Firmware PS version information and supported model PS on Openstack, kilo, Liberty and Mitaka.

  Thank you and best regards,

  Hello

  Dell certifies OpenStack w/Equallogic.   This is the underlying software as Cinder, who does the work with storage arrays.  The driver uses the orders of EQL group CLI, the syntax has not changed, except for the new features.

  http://docs.OpenStack.org/liberty/config-reference/content/Dell-EqualLogic-driver.html

  https://www.rdoproject.org/storage/cinder/using-Dell-EqualLogic-for-cinder-with-RDO/

  He has no problem with the latest version of the firmware.  It is good to run something current, or at least near current in General.

  Kind regards

  Don

• Upgrade Equallogic HIT failure with error Kit 4.8 to 4.9

  During the process of upgrading the Dell EqualLogic 4.8.0, host integration tools we get an error message: Error 1720. There is a problem with this Windows Installer package. A script required for this install to complete could not be run. Contact your provider to support personal or package. Custom action error in script-2147024773 CleanDepriicatedShortcuts,: line 28, column 3,.

  Don't know what to say exectly. I tried a new download, but it seems to me that's no mistake because of bad download of .exe or .iso.

  System logs show the following.

  > Product: Dell EqualLogic host - 1720 integration tools. Error there is a problem with this Windows Installer package. A script required for this install to complete could not be run. Contact your provider to support personal or package. Custom action error in script-2147024773 CleanDepricatedShortcuts,: line 28, column 3

  We have a Windows Server 2012 and a 2012 Cluster Hyper-V in R2 with several Windows Server 2012 R2. I tried the upgrade on Windows Server 2012.

  Please help.

  I was able to fix it myself. It seems to me, the Setup program needs all the shortcuts on the place of origin. If there is a lack or there was a change of name of a folder, the Setup program fails with the error message above.

  There are two solutions. Copy all shortcuts and folders to another installation or run the repair installation. I did the first step copies all the shortcuts to another facility.

  I was able to upgrade successfully on all installations.

• How to delete files orphans on the equallogic virtual volume

  It is in reference to article kb of VMware to the address following:

  https://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2108332

  So what commands or GUI options are available to remove volume virtual orphaned objects?

  vSphere indicates the virtual volume in a vacuum but a space used 53 GB to 1 TB. The equallogic gui shows several virtual machines with 0 Mb in size associated with the storage container. Any attempt to remove gui and ssh results in the following error 'storage container must be empty to be deleted. The storage container is also showing that it incorporates snapshots and related clones that I can't access.

  Storage container _ Information
  name: XXXXXXXX-VOL001 UUID:
  Description:
  Size logic: logical 10TB used: 354GB
  Free logic: 9.65 TB Aggr physical size: 1 TB
  Physical AGGR used: 53GB free physical Aggr: 971,02 GB
  VVols: 2 VVolSnapshots: 1
  VVolLinkedClones: OnlineVVolsSnapshotsLinkedClones 0: 2
  _______________________________________________________________________________
  _ Information _ pool storage container
  Name of the cluster: the default physical size: 1 TB
  Used Physics: 53 GB physical free: 971,02 GB
  Free space warning percentage: 10%
  _______________________________________________________________________________

  Fixed it myself using "vvol" or "AUTOMAGIC help command. Here's a tutorial. Use at your own risk!

  SSH in equallogic array.

  [Enter the support mode]
  support

  [Show vvols on Bay Equallogic and check if the vvol that you are trying to delete is related]
  See the vvol
  Bound _ Information _ VVols
  _______________________________________________________________________________
  Name size Type container Description
  --------------- ---------- ----------- ---------- ------------
  04250816-50 ° c 6-4, 350GB vmdk-vvol XXXXXXXXX XXXXXXX-sna
  BBC-92f0-2869-p-2016-05-
  f95a41ad 08 - 20:53:3

  [Select the vvol]
  vvol select 04250816-50c6-4bbc-92f0-2869f95a41ad

  [Displays details of the selected vvol and locate the linked access policy]
  Show

  _ Information access policy
  Name: VSMAR-160408124414913 UUID:
  0-000000-000000000-0000000000000000

  [Untie the spectacle of the access policy that you are able to remove the object vvol]
  remove the access strategy VSMAR-160408124414913 link

  [go up one level]
  output

  [check if vvol is now independent]
  See the vvol

  Non-consolidated _ VVols _ Information
  _______________________________________________________________________________
  Name size Type container Description
  --------------- ---------- ----------- ---------- ------------
  04250816-50 ° c 6-4, 350GB vmdk-vvol XXXXXXXXXX XXXXXX_1-SNA
  BBC-92f0-2869-p-2016-05-
  f95a41ad 08 - 20:53:3

  [delete the orphaned vvol]
  vvol delete 04250816-50c6-4bbc-92f0-2869f95a41ad

  [May not be no need to go up one level]
  output

  [list of storage containers]
  show tank

  Name logical size physical pool size
  --------- ------------ --------- -------------
  Value by default 10 TB of XXXXXXXXX 1 TB

  [select the storage container that had the orphaned objects]
  storage container select XXXXXXXXXX

  [view detailed information and check that used physical Aggr: or used Physics: is now 0MB]
  Show

  Storage container _ Information
  name: XXXXXXXXXXX UUID:
  Description:
  Size logic: logical 10TB used: 0 MB
  Free logic: 10TB Aggr physical size: 1 TB
  Physical AGGR used: 0MB free physical Aggr: 1 TB
  VVols: 0 VVolSnapshots: 0
  VVolLinkedClones: 0 OnlineVVolsSnapshotsLinkedClones: 0
  _______________________________________________________________________________
  _ Information _ pool storage container
  Name of the cluster: the default physical size: 1 TB
  Used Physics: 0 MB free physical: 1 TB
  Free space warning percentage: 10%
  _______________________________________________________________________________

  You are now able to remove the storage container in the GUI.