Equium A300D will not start.

Similar Questions

• Equium L10 will not start

  Please help - my Equium L10 will not start.

  Power supply is OK. When the power is connected the orange battery light comes on. I press the power button the green power light turns on momentarily (literally a Flash), then both the Green and orange lights out with orange alone returning it on about 2 seconds later.

  Else does nothing - no fan activity, no hard disk, no activity of the screen activity, no other light - you get the picture!

  I tried the following:
  Removed battery and tried to start with AC power not only - no joy
  Removed AC power and I tried booting with battery only - no joy
  Barrette of RAM removed and reinstall - no joy

  Does anyone have ideas before considering a tech? Suggestions (with the exception where to paste!) would be welcome.

  Kind regards

  Gary C

  Hmm .He doesn't sound good. For me, it looks like a motherboard problem. It is maybe something wrong with electronic power to the Board of Directors of s. But not for sure.

  What you can do is to remove the battery and unplug the power adapter for a while.
  Wait about 20 minutes and connect the battery and adapter for the laptop. Then try turning on the laptop computer.
  If this does not help I recommend contact the ASP technician, because I don t think you will be able to know what's exactly wrong.

  So I hope that the technician can find the fault quickly and can solve this problem.

  Good luck

• Equium A300D will not be market or start - stuck on the eve

  Hello

  Toshiba support staff,

  I have a Toshiba Equium A300D who suddenly decided to not turn on - I have pressed the power button down, alt del, shot control button
  it exceeds to find a reset button and found no button at the back - don't know if there is any other command key that I can use so he can start.

  Can someone out there suggest what I can do?
  It is as if he is trapped in mode 'sleep'.

  Satellite light isn't on one or things of the touchpad will not turn on...

  Thank you

  Barbara

  > Toshiba support staff.
  First of all, it is a forum from user to user, I doubt that you will find here a people of Toshiba

  > I have a Toshiba Equium A300D who suddenly decided to not turn on - I have pressed the power button, maintained alt del, shot control
  it exceeds to find a reset button and found no button at the back - don't know if there is any other command key that I can use so he can start.

  Try this:
  Remove the battery, disconnect the adapter
  Wait several minutes (30 minutes), then reconnect the two parts.

  Then try to turn on the machine.
  Check it out and post the results.

  Good luck

• Equium A60 will not start

  Hi, I am despartely needing help with my A60 equium that won't start. When you turn the button lights up, fan and starting, but then in a few seconds the cutting power. I tried different sources of energy, also just by using ac power and battery just all produce the same results. I had installed a memory chip a few months back and thought it might be that, but when I took it off the laptop has always been the problem.

  Is there that anyone may be able to help me with this problem? Thank you

  TAF

  Hi Michael,

  The first thing that happens when your, press on the power button on your laptop, it's that the CMOS chip (which contains your BIOS) through a pre-deignated POST (Power On Self Test) process that verifies the functions of the material of base components after what the BIOS will be charged which will lead in turn to the operating system itself being started.

  If a failure or a problem occurs during POST and then power on the sequence stops (usually after a series of beeps are emitted that are coded to help the diagnostic process. The actual beep codes are specific to the manufacturer of the CMOS/BIOS chip.

  If you receive no all audible sounds, then it is likely that the problem is very early in the POST process and may indicate a problem with your main card or your electronic internal.

  You can try to remove and and reinstall devices such as RAM memory modules, hard drive, optical drive, etc to see if this corrects the situation, but if not then you will need to take the device to authorized, Service partner who has the diagnostic equipment needed to perform accurate control.

  Kind regards

• Equium L20 will not start properly

  My laptop L20 primer not. A black screen appears "apologize for the inconvenience, but windows did not start successfully.

  Then tells me to highlight a choice of starting up, but when I choose, it moves quickly on a blue screen that I cannot read, then goes back to the same black screen.

  Help! It feels like Groundhog Day.
  Cannot make it work.

  Hi Donna,.

  More simple you take it out of this situation is to reinstall your operating system of the recovey CDs. Unfortunately this won't replace your data (unless you have partioned your hard drive and store your data on a second partition).

  This problem is usually caused by a missing or corrupt system files that prevent Windows from loading. Of course, you can try to recover the situation by using the since the original Microsoft Installation CD Recovery Console if you have one.

  It is also possible that the failure is due to a defective hard drive but it will become apparent when you try to re - install.

  Kind regards

• Equium P200 will not start

  I have a notebook equium P200 and it won't start, it started, then froze when I turned off and then on again, I got was the toshiba logo then the symbol loading then nothing just a black screen. I rebooted and let it go through the analysis in case of errors, but it will still go to a black screen. It is running Vista. The blue disc light that lights up normally when it starts does not illuminate. I don't lose everyhting on it or can it be saved.

  Post edited by: sugajars

  Hello

  Try this:

  -Remove the battery
  -Unplug the power adapter
  -wait 1hout
  -bring the two parties together and try to turn on the device

  I hope that you will be successful if not is not-> the time for service :(

• Equium A60 will not start - get a beep code

  Hello

  This laptop has problems with ATI (even those included on the recovery disk) display drivers. He created a blue screen on a dll file.

  After reading around, I found that it was recommended to upgrade the bios, after going to the appropriate section of the Web site, I downloaded the flash tool from windows for the laptop bios.

  I ran and it opened, returned to the laptop and the screen is blank, a blue ring around the power button is on, but no display.

  I left it for a period of time see if it would to restart or something, but nothing has happened, it would not be the button turn off so I unplugged the power and removed the battery.

  To again turn on the laptop, it only stays on for about 3 seconds then turns off again.
  I get the beep code: short break, Long, short break, beep, beep beep, then it turns off.
  The caps lock and numlock keys are turned on.
  The DVD drive light blinks.

  But other than that, no display etc.
  Ive tried the battery leaving aside for awhile.

  Anyone have any ideas why flash bios toshiba own this would cause? Also what can I do about it? in any case to recover the bios etc via a recovery mode?

  Thanks in advance.

  PSA67E

  Hello

  Well, unfortunately for me it looks like a hardware failure.
  Maybe the motherboard is broken.
  These problems may occur if you use a bad BIOS or the incorrect BIOS update procedure.

  Please check this document FAQ How to upgrade the BIOS:
  IOS http://eu.Computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?z=234&service=eu&from=faq_selection&CFID=B & FID = TRO0000000b07

  Unfortunately if there is something wrong with the hardware you should ask Toshiba service for assistance.

• Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running.

  Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running. I can't enter to give more details. Can anyone help? There are a load of work due to deliver to the printing press Monday

  Have you tried to boot from the Partition Recovery and repair then the disc from there, using disk utility?

• G5 will not start. LED light on. Fans before working.

  Early 2005 G5. running 10.5.8.

  G5 will not start. LED light (no flashes not but solid). Fans before working. Rear fans blowing not. Cleaned up the dust. A exploded during a down and will not restart. Any thoughts? Is that a bad diet? What I would do. Thanks for any help. I love this old computer and hope to keep fixed and working.

  Sam

  Some of the fundamental things include the pram/clock battery replacement

  since they may be dead; then with a power failure, sometimes the Mac

  do not restart. Usual power management unit & reset NVRAM/PRAM are

  methods that sometimes also used as a troubleshooting measure.

  • Reset the Mac chip power management: (see SMU)

  http://www.thexlab.com/FAQs/resetpmchip.html

  • How to reset NVRAM-LANDAU on your Mac - Apple Support

  A hard reset can sometimes be used, where the power is disconnected

  the logic board and power removed from grill; Then push the Start button / stop.

  (But maybe not. Several PowerMac computers, I had, some people found this helpful)

  You may also remove and reposition cards and other items

  the inside of the case, to be sure they are connected properly. Be sure to not

  In short anything, due to the static load or residual power in the circuits.

  The hour is late here, so I'm not going offline; If all goes well a battery original or novel, etc.

  can help to put it on again. Also sometimes the power supply has some faulty fans,

  circuits or capacitors, so they can be troublesome to repair or replace.

  Good luck in this case!

• Firefox will not start after update

  Firefox will not start today. I think he had an update yesterday.
  Click it, lift the loading symbol, but never implemented. In Task Manager it is a firefox.exe * 32 running. Have you tried to uninstall, delete Mozilla Firefox folder in Program Files x 86 iti also tried to suppress the appdata profile (after saving the Favorites and passwords). I can't even boot up in firefox safe mode and can not get to start Profile Manager. If I start (7 x 64) of windows in safe mode, I can start firefox. I use Norton Internet Security. I checked the settings of firewall smart and experienced of firefox is still set to allow. I tried starting firefox with smart firewall turned off and firefox still refuses to start
  Renounce top almost ready

  Hello ziggy1, as this can sometimes be caused by a malware active on a system, please run a scan with tools of different security like the free version of malwarebytes, the adwcleaner and the scan to microsoft security.

  Fix Firefox problems caused by malicious software

• Carillon of boot loop - start 2011 MBP will not start.

  I have a start 2011 15 "MBPro8, 2

  Quad Core Intel Core i7

  2.30 GHz

  Boot ROM version: MBP81.88Z.0047.B2A.1506082204

  Intel HD Graphics 3000 VRAM:512 MB

  AMD Radeon HD 6750M VRAM:1 GB

  8 GB of RAM 1333 MHz DIMM0

  It will not start.  Trying to start the machine, it enters a loop-

  1. startup chime

  2. grey screen with Apple

  3. the small wheel starts to turn under the Apple

  4. the screen goes black

  ... and the cycle starts over.

  The computer does not start in Mode safe.  In an attempt to safe mode the loop above has the addition:

  3. a progress bar is displayed but does not progress.

  I have reset the PRAM

  It will start up in target Mode, so I was able to recover data

  In target Mode, I was able to run first aid utility on the drive.  This has not fixed the problem.

  I can hold down the Option key and see Macintosh HD and the recovery Partition.  If I try to boot from the recovery partition, I get the same loop.

  I can start in the Test of online material, which revealed no material problems

  I can boot in Verbose mode and it always happens in the same place

  Execution fsck_hfs (version 226.1.1 of hfs)

  BootCacheControl: cannot open /var/db/BootCache.playlist: 2 no such file or directory

  ' ' It would be possible for me to insert the "var/db/BootCache.playlist" file using target disk mode?

  Other thoughts?

  Check Google for this error, it seems to be common.

  Apparently the startup configuration file is corrupted. These 2 articles can be useful:

  http://www.Hackintosh.computer/?p=67

  https://www.iFixit.com/answers/view/192201/unable+to+open+-var-db-BootCache.play list % 3A + 2

• I nned to know the procedure I use to get can Mac 2008 Desk top that will not start. I don't know how to connect two computers, my portable Mac Air 2013 on my desk, now I need to know how get the workstation files in order to appear on my mac air so I can

  Does anyone know how after I connect to my office 2008 Mac (which will not start.) to my computer laptop (2013 Mac Air). What are the steps that I need to know to get the Desktop files is displayed on my mac air so I can copy files to your laptop, especially my Itunes folder.

  Thanks Jerri

  If you can't get the iMac began and ongoing implementation, you will not be able to use the target disk Mode:

  https://support.Apple.com/en-us/HT201462

  Then the option is to take the iMac HARD drive, install it in an enclosed, and connect the HARD drive to the MBA via the USB port.  If the HARD drive is recognized, you can copy the data out of it.

  Ciao.

• Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process.

  Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process, but do not remember.
  Tried running firefox.exe Pei but error message:

  XML parsing error: the undefined entity
  Location: chrome://mozapps/content/profile/profileSelection.xul
  Line 18, column 1:
  "< dialog < =" "^ =" "p =" "> < / dialogue >

  Running on Windows XP SP3. No problem whatsoever before moving to 27. Sending of Chrome that I can't open Firefox at all.

  Thank you, jschaer2000. In the meantime, he works. How long, we'll see ;-)

• Hi, I just upgraded my 4s to 9.3.2 and now it is completely dead and will not start. Had no problem with any other previous updates.

  Hi, I just upgraded my 4s to 9.3.2 and now it is completely dead and will not start. Had no problem with any other previous updates.

  Sorted now

• Updated the macbook pro of el capitan and now will not start. Instead, I get the error message "your computer restarted due to a problem". Someone at - it suggestions on how to solve this problem?

  Updated macbook pro today for the latest version of el capitan and now will not start. Instead, I get the error message "your computer restarted due to a problem". Someone at - it suggestions on how to solve this problem?

  It would be helpful to post what the screen says.

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  https://support.Apple.com/en-us/HT201295

  Subject of memory NVRAM and PRAM

  https://support.Apple.com/en-us/HT204063

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  https://support.Apple.com/en-us/HT201262

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  https://support.Apple.com/en-us/HT201314

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204904

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.