Equium M50-192 will not start - HARD drive problem?

Similar Questions

• Equium M50-192 does not start

  Hello
  I posted a question here earlier on my laptop and I had useful assistance but he juices do not appear to have sorted.
  but I have now no wat it is not and just don't need to know wat it is

  I have a toshiba m50-192
  and when I turn it on it does not start going to a black screen and gives me errors (pxe - e61)

  in my last question, I was told that it was the hard drive was dead.
  Since then, I've replaced my hard drive and my hard drive, but it always seems to be doing almost the same

  I can get into my bios and the hard drive is recognized.
  I tried to boot from the disk recovery and hard drive but no joy.

  but since I replaced both drives when I boot from the hard drive it gos just a black screen with the little line in the upper right corner.

  but when I boot from the disk it gives me this error pxe - e61, which is where his tent to boot from the network I have read.

  until I replaced my hard drive, he had a strong look that has disappeared since I replaced it.
  the disk hard im trying to use now is off my brother's mobile which all ready installed xp on it it would make a difference when you try to boot from the hard drive? (my laptop is xp)

  I read something on definition of my hard drive to the master and my cd player to the slave that would make a difference and how would I do?

  I think it's as much information im aware off

  could someone please help as im stuck and did not have any idea what to do

  Post edited by: domio
  o im also getting the and pxe - e61 pxe - m0f error code

  Hello!

  What happens to an error you get? Please post what we can help you.

  To be honest that I n don't know what you mean with clip Ribbon keyboard but if the keyboard is faulty or something else, the keyboard completely must be exchanged. You are not a unique key or something else.
  If you want a new keyboard or other spare parts contact your local ASP.

  Good bye

• Equium M50-192 doesn't start after upgrade memory

  Hello

  at the moment I have 2 x 512 MB sticks of memory in my laptop, I bought 2 x 1 GB sticks of mrmemory.co.uk as an upgrade. When I tried to use the computer will not start until I put the original RAM support. State Mrmemory that they sent me the correct memory for my laptop, I have done no matter what wrong?

  Thank you
  Andy.

  Hello

  I think that the modules of memory are not fully compatible or defective
  It's the only plausible explanation why start Notepad doesn t
  As far as I know the laptop can be upgraded up to 2 GB of RAM (2 x 1 GB) and this module should be compatible DDR2-400 and 533 Mhz 1 GB (PA3411U-1M1G)

  PS: Have you tried to update the BIOS by using the old memory modules?
  Check if you are using the latest version of the BIOS if it is up-to-date and check if the new modules would

• Qosmio F60 turning is not on - HARD drive problem

  My F60 running stock windows 7 and when I turn it on I get a black screen with the following text:

  + Check the file system on C: +.
  + the type of file system is NTFS.
  + Volume name is s3a5802d002 +.
  + One of your disks needs to be checked for conisitency. +
  + You can cancel the disk check, but it is strongly recommended that you continue.
  + To skip verification of the disc, press any key within 10 seconds.

  If I leave it just like that.
  I try to ignore it, and it does not work so I turn it off and go again on the third time, to turn on while I press ESC. What should I do about it?

  Re: do everything or send it as it is only 6 months old, it is Bernard did this for 5 months

  Hello

  It sounds a bit like a HARD drive problem.
  I recommend checking out the HARD drive using a free tool called Drive Fitness Test
  This free tool allows you to get more details on the State of the HARD drive and maybe some error would be detected which would mean that HARD drive failures and disk HARD must be replaced.

• Satellite A660 - will not start initialize drive HARD failure

  Hello
  first of all thank you for your time.

  Model: Satellite A660 (PSAW3A-07U00R)

  The problem started yesterday, the computer has been going slowly as a closed application, so I held the off button until the pc is turned off. When I restarded the laptop, it went to a screen saying: start windows normally or repair Windows (recommended)

  When started normally it hangs just a blank screen, repair Windows recommends a system restore to a previous point that did not work. As it crashes again. I tried pressing F8 and boot in safe mode, but even once it just hangs. Then, after having repeatedly tried safe mode and another system restore the computer then hangs when I press F8. After that, the computer passes in front of the Toshiba logo with F2 and F12 options screen (which still works) and then it rises the initialization has failed then shuts off and comes with start-up bootfailed failed with a few numbers and letters, then it goes to a small box entitled menu starting with 4 options. These are some
  Toshiba MK6465GSX HDD/SSD
  CD/DVD MAST * UJ141ES ABD - CMB
  FLOPPY DRIVE
  LAN

  If I press ESC, it passes through the loop of bootfailed and ends at the same screen, if I press on enter "HDD/SSD Toshiba MK6465GSX" then he quickly returned to the screen and at the bottom it says [HDD/SSD Toshiba MK6465GSX] failed.

  I do not understand why it has gotten worse over time. Can anyone think why it occurred and more importantly, how can I get my pc working again? Note: held 0 then start does nothing for me atm

  Best regards, Matthew

  Hello Matthew,.

  To be honest, I agree with Akuma and it could be related to a dysfunction of HDD the error you described, but ensure 100% there s no software problem, you should try the Toshiba Recovery disk Windows installation. Something may be confused until the Windows installation and recovery of files on the HARD drive, so it cannot be started. Recovery disc will resolve this problem by formatting the HARD drive and restoring the settings box.

  If it still doesn t it work s hardware malfunction but an authorized service provider can solve these problems under warranty for free. So just contact the guy and ask for help. ;)

  If you have other questions or already solved the problem, please let us know!

• Equium A100 - 338 will not start

  Hello everyone I have an Equium A100-338. I bought it in Ireland a little one there.
  Well although it is just out of warranty and it won't start.
  The blue light comes on and the hard drive light comes on for a second, and nothing happens.

  I tried to disconnect the battery a few times. Would not at all light up the screen.
  I plugged the machine on an external monitor but not luck.

  Suggestions people?

  Post edited by: ADMIN

  A new motherboard is a part of portable more expensive so buying a new motherboard is always a costly affair.
  Maybe you should look for some motherboards of second hand on Ebay

• G4 will not start hard fast motor running

  Help, I have a...

  G5 processor 1.6 Ghz, Mac OS X (10.5.6), RAM 1.25 I use not.  recently, I need to find some old documents about this store, so I tried to start it and I hear the ping of start-up and the hard drive starts spinning and then it continues to become stronger and stronger, but on the screen, nothing happens.  on an attempt I got a message that I've never seen before, which send I need to restart the computer. This message was not in your typical dialog box.  It was written in big letters on the screen in big letters and it's in English, French and another language.    as per charge, started again and I tried many times.   I tried the thing of Landau, did not work.  any suggestion would be greatly appreciated.  Thanks in advance for your help.

  Hold down the SHIFT key at startup... did do better?

  Hold the option key or the ALT on startup, did show the choice of start?

  It has been disconnected from power for a long period of time?

• Satellite Pro A10 does not start (HARD drive seems to be missing)

  Hello, I hope someone can give me some advice on this problem: I have a 2 years Satellite Pro A10. Recently, it starts not at all and I noticed that if I look at directories on the C: drive using the command prompt, it said "file not found". Cannot start Windows at all, not even in Safe Mode.
  Using the recovery disks is I help spread messages as no such fixed disc and 'Extraction impossible '.
  is - that say I have:
  1 a hard drive damaged
  2. defective connections on the HARD drive? -If Yes, how I fix that?

  the system didn't crash before it happened, she doesn't have to load up when I started it.
  Would appreciate any help.

  Thank you
  SCL

  Hello

  Well, it could be a hardware malfunction of HARD drive. Yes, it is possible. But I don t think that there is a bad connection. You used this HARD over the last two years and you n t change the settings of connections on this HARD drive. Is this good?
  If it possible s so I suggest you of to completely format the HARD drive.
  Then try to start the recovery procedure.

  However if the HARD drive has a functioning default (ie. crushing of the head), so the only way is to replace this device.

• Dim 9200 does not start; hard drives not found

  I have a Dimension 9200 with 4 GB of RAM and two Seagate Barracuda 7200.10 250 GB hard drives that works well for 8 or 9 years.

  However, he has recently stopped start and displays the following message:

  Drive 0 not found: Serial ATA, SATA-0

  Drive 1 not found: Serial ATA, SATA-1

  Strike F1 key to continue, F2 to run the Setup utility.

  In addition, on the homepage of DELL for this message to appear, the splash remains for about a minute after the progress bar reaches its full potential. Meanwhile, the SATA 0 drive emits a continuous clicking sound (something like an old mechanical clock every second ticking).

  Diagnosis initially 2 and 3 remain on (failure possible floppy or hard drive according to the manual) until the machine beeps and moves out of the start page of Dell to the message above. Exactly at this place, diagnostic light fire 1, 2 and 3 (manual says another failure).

  I reinstalled the two HDs that made no difference whatsoever.

  I also removed the cables power and data from disk SATA-0 and rebooted. This time, no delay was observed when the splash page reaches the end of its race progress bar, no noise has been heard since the SATA-1 remaining drive but the same message above appeared once more, as did the same 1, 2 and 3 diagnostic lights

  I also put drive SATA 1 on SATA 0 and connected the power and SATA-0 data cables. However, the behavior is still the same (note that I use the Grub bootloader and it is installed on SATA-0, then the other drive is not bootable).

  I also started from a USB key containing the GParted partition manager. It starts fine, but the single disc he sees is the USB. Or the SATA drives are recognized. It is worrisome.

  I bought a new Seagate Barracuda 7200.10 with 250 GB which should arrive later this week. However, I'm starting to think that the problem drive is not my only problem (and of course, that's what the 1,2 and 3 diagnostic lights would seem to indicate).

  I should be grateful if you would for clues, opinions or suggestions.

  Thank you

  Paul

  Have you tried to enter the bios Setup, and then press alt + F? Save/quit it can detect readers.

• Equium A60-155 will not start on the recovery CD

  Hey,.

  Just got a computer satellite phone of second hand from a friend who has been upgraded - gave me for free because it doesn't seem to work properly (he thought was a problem of HARD drive).

  I replaced the HARD drive (with one I formatted on my desk but an envelope that I have for it) and have the recovery DVDs, but I can't do anything with the machine... when I turn on I only get to the Toshiba logo screen and does not go any further (with the exception of time weird when I get a blank screen)... now the C button or trying to get into the BIOS (tried hold ESC F1) (, F2 or F12) does not work.

  I opened the machine and everything is correctly connected - the DVD player also seems to be spinning and reading the disc, but nothing loads of it.

  Anyone know what this could be and what I can do to fix it, or is it a lost cause?

  Thanks for any help!

  Adam

  Hi, EIB

  I assume that this satellite has installed Toshiba BIOS and therefore, it should be possible access the BIOS by pressing ESC then F1.

  You said that this laptop does not have the Toshiba logo screen it seems we can't get the MESSAGE correctly well I m sorry to say but in my opinion the portable hardware malfunctioning.

  Maybe something wrong with the jury. and not with the HARD drive

• Equium M50-192: where to find a driver for DVD/CD player

  Hi, can someone please tell me the site for the latest driver for my CD/DVD drive because none is listed in the driver update page, thank you.

  AFAIK, the Toshiba driver page, that you will not find the special CD/DVD drive drivers. The laptop uses a simple common Microsoft Windows driver
  That's why it of not necessary to install the 3 drivers

• Equium L350 - 10L will not start

  Hello

  I have a Toshiba L350 10 L satellite, I had problems with, firstly he did nothing, now I replaced the motherboard and processor, but now when I turn it on I have power light and fan rotates but does not start at the top, can someone please help me with this problem.

  Thank you very much

  > now, I replaced the card motherboard and CPU
  Huh... who knows what you did exactly, did it on the right path and at least replacement of the CPU is very delicate is not easy to tell a lot about all this.

  How should know us if you've done everything correctly?

• Equium P200-139 - will not start

  Got a P200 does not start.

  Blue light turns on and sounds like its gunna start up but the screen remains black and the often turns after a few minutes. So basically I can't even in the computer to try to fix the problem

  Grant... .do ideas?

  Hey,.

  If you think that the boots of laptop but you don t see something, I would like to connect an external monitor in your case. So, you can check if the notebook starts really or not and if so, you can see what is the reason.

  If the external monitor is also black I would try this:
  -Remove the battery and the AC adapter
  -Wait at least an hour
  -Reconnect AC/DC adapter and install the battery
  -Make sure the battery is fully charged
  -Try to start the laptop

• Equium A60-155 will not start

  Hello

  I have an Equium a60-155, that I knew that she works for a while, but recently I came with a new poroblem... my laptop guard turn off without notice and loses all power.

  The battery has been dead for some time and lasts about 5 seconds, but I've been using the AC adapter.

  Recently, she stops and even the LED lights for the power/battery adapter / is not on.

  At first I thought it was the fuse in the adapter which could have been blown so I replaced it, and it started to work again, but then after a few minutes, it stops and lost all power.

  I had this during the last days and I noticed that it regains power when I unplug the power adapter from the mains supply and remove the fuse and put it back in but his lasts only for a few minutes.

  I don't know if it is a hardware problem or I just need a new adapter. Someone at - it similar problems and can offer any adivce?

  Hello!

  What do you think that the laptop is overheating? I don't know, but if so the laptop would also immediately turn off m.
  So, try to clean the laptop with a jet of compressed air to blow the dust from the cooling fans. So you don't have to disassemble the laptop.

  If it doesn't help it's really hard to say what the reason is for this maybe you should bring the laptop to an authorized service provider. Technicians can check the laptop.

  Good bye

• (Redirected) Alienware X 51 R2 will not start. Repair of the system sees no HARD drive

  Hey,.

  My X 51 died and I can't get it to work. Looking for suugestions.

  After months of random boot errors and re-formatting my HARD drive a few times it will not start upward. It starts either error that says "no found boot device" or it goes to a screen of "diagnosis" of dell alien ware which basically ends with a message saying either

  -reboot again

  -Advanced options > recovery cd, repair, ect.

  When I try to use the windows recovery CD 7 he does not see HARD drive (no HARD drive installed, that it is, I reinstalled it a few times too to make sure it was not a coward).

  -J' have a HARD drive, usb drive, and when I took out the HARD drive I can access my files NP via laptop, so I'm not confident, that's my HARD drive which * out.

  Now, before all this happened, I had to reformat my computer because it was literally so slow it would take like 5 minutes to open a folder (potential virus or something I don't know) and me random boot errors.

  Someone at - he had a similar experience?

  Better in this position in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.