Error-1073807343

Similar Questions

• Error-1073807343 when taking picture of façade

  Attachment vi works very well to take a picture of the front, but when I try to reproduce the same code on a different VI, I got the error: error-1073807343

  VISA: (Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system.

  The code I try to use in another VI is attached: front panel take photo - Block Diagram.gif

  Your VI works well.

  I don't think that that this VI is the origin of the problem

  VISA error takes place a few other reasons, explained here.

  Also, please check that the cluster of error is done correctly through the VI (if you use it as a Subvi)

• VISA 1073807343 errors and 1073807202

  Hello everyone,

  I have several issues with the VISA 5.0.3 and LabVIEW 2010 SP1, and I don't know if or how they are related, so I'll post as much information as I have here. Please excuse the super post long, just trying to be thorough.

  Error BFFF009E (same as 1073807202 I think) appears to the MAX aperture as seen in attached ss1. When you try to open the VISA Interactive Control (IC), I get the message "failed to initialize the library VISA. The VISA interactive control utility will leave. "When I open any VI with a VISA resource and try to click the drop down arrow on the right to see the resources available, the arrow remains derpessed during a second, no field drop-down list is displayed, and then it returns to its original blank State. These problems all live together now, but before I could select BT VISA resources and use VISA IC, while I have always seen the error MAX.

  I tried to fix VISA, as well as VISA uninstall-reinstall 5.0.3 which I believe is the most recent version. No change. I also checked that visa32.dll exists as suggested in the article below. See systeminfo.txt attached to the installed software.

  http://digital.NI.com/public.nsf/allkb/1D1736BFD24A09878625742500241386

  This error seems to be related to an oscilloscope Tektronix DPO 2014 I connected via USB (or maybe something to do with TekVISA?). By this I mean that if the scope was connected when my computer started, this error occurs. When the field is not connected at startup, I don't see the same problems as above. Instead, I get...

  Error 1073807343 (BFFF0011) when you run a VI with a VISA resource to a serial device (see ss2), or connecting to the device in IC of VISA (see ss3). I also always see the error of BFFF009E to the MAX, but not the other problems on front. I can connect to these serial devices in hyperterminal and communicate very well here. Seems similar to the post below and also, I can't find visaconf.ini, but the solution does not apply as I LV 2010. In addition, ironically, I use VISA very well talk to the scope (whether to the MAX or LV) via USB if I connect after booting.

  http://forums.NI.com/T5/instrument-control-GPIB-serial/using-HP34401A-in-LabVIEW-yields-error-code-1...

  I use series of USB adapters made by Ultra (http://mail.ultraproducts.com/product_resources.php?cPath=35&pPath=782&productID=782 ) to go from instruments of series to my USB ports and the computer I'm unfortunately has no serial ports to be tested with, nor do I have another brand of the adapter. I know these converters can sometimes be a VISA problem, but I was certainly with it even without problem before.

  They that all seem to have intermittent problems, because I have seen both before as I have developed and pushed to go to strange as things exchanging (apparently identical) USB extension cables or restart a dozen times. This issue has been driving me crazy for weeks, I am looking for help to try to solve it finally.

  Thank you

  Ratti

  I think I got especially. Looks like it was TekVISA who got in the way, and if Visa32.dll was in the right place, it appeared (in properties > details) as the version of Tektronix, not the version of LabVIEW. After you have uninstalled all Tektronix as well as NI-VISA, he had disappeared, but no money to install or repair NI-VISA would be replaced by a version of LabVIEW Visa32.dll.

  However, with the help of the article from the link below, I discovered that the repair of the installation of the driver NI-VISA DURATION is what replaces Visa32.dll, as opposed to NO-VISA just as messages of error and other links seemed to suggest.

  http://digital.NI.com/public.nsf/allkb/B283196340462DFD86257633006DC799

  Now all the VISA stuff works again, except of course for the scope of Tektronix. I'll keep this battle for the future. Guess I just needed to talk to myself for a while.

  -Ratti

• 1073807343 error occurred during the opening of Visa

  I have a vi that:

  -Locate the USB port that RS485 communication device is connected

  -sends a command to each sensor

  -reads a response from each sensor

  -performs a calculation on the answer

  -saves the response to a file of measure

  I used a flat sequence to query each sensor.  When the vi is started, it throws error 1073807343 indicating "insufficient location information or the device or resource is not present in the system."  When I cancel the error, the vi works well with no other errors.  This error started to appear when I upgraded to LabView2015.  I also use the LabView Base development on a computer laptop Dell D630, WinXP SP3 version.

  I'm taking a guess here, but I think that the error is in the opening a new piece of reference Visa of the code block.

  Does anyone know why this error is thrown, or how to fix my vi?

  
  

• The use of HP34401A in LabView gives 1073807343 error code

  Hi all

  I used the Example.vi HP34401A of the read-only to read data from HP34401A.  However, the following error occurs,

  "Error-1073807343 is is produced when opening VISA in HP34401A Initialize.vi-> Untitled 1

  Possible reasons:

  VISA: (Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system. '

  I use NI GPIB-USB-HS and I can contact HP34401A to the MAX.

  I can't understand why this error occur and how to solve it.  Please help me.

  Thank you very much.

  
  

• The error auxiliary inst 1073807343: Noob question

  Hi guys

  On my PC, I got an entry series great working with a previous VI (made by someone else). But the first VI, I've done here:

  http://sites.Google.com/site/oraclemechanics/file

  shows the error:

  Error-1073807343 during acm2d ins pure.vi:Instance:0-> acm2d Assistant ins Assistant pure.vi to the property node (arg 1)

  Possible reasons:
  VISA: (Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system.

  The serial port on my PC should be ok because works very well with an entry of data in a previous VI series.

  Cannot know what the problem is. Help, please. Thanks in advance.

  Hi guys

  I solved the problem by adding an error suppression function. Muahahahahah...

  Assistant of the instrument was probably a few pips huh...?

• All my instruments back VISA errors

  I recently added the cryogenic temperature controller pilot Lake Shore model 336 in the folder instr.lib under program files of National Instruments. When I tried to run one of the example programs accompanying the driver, LabView gave:

  1073807346 error occurred while VISA opening to edge the Lake 336.lvlib:Initialize.vi-> Lake Shore 336 write Curve.vi

  Because I was working on an another VI at the time I just ignored the error and planned to fix it later. The other program, which had a servo error since last week-free motor, are also starting to give an error:

  Error 1073807343 has occurred to clear VISA

  Improper installation of the Lake Shore drivers affect somehow my other instruments? I am running LabView 2012 and have NI-VISA 4.6.

  Thanks for any help.

  Lakeshore pilots apply their own version of VISA?  Sometimes conflicting versions of VISA can cause problems.

  Lynn

• Serial USB Hub error

  Hello

  I am currently using a USB-6009 case and another device connected via USB using a virtual COM port. These are connected to the computer via a powered external USB 4 port hub. Whenever I run VI I get the following error:

  Error 1073807343 has occurred to the property node

  (arg 1) visa set up a Serial Port (Instr) .vi.

  > Read MI3 Temp.vi-> SagDAQ.vi

  Possible reasons:

  VISA: Insufficient location information (Hex 0xBFFF0011) or

  the device or resource is not present in the system.

  After this error I have to disconnect and reconnect the device to use. I installed the drivers that came with the device and if I use the software supplied with the unit provided I have no problem with the device at all.

  I also noticed that if I do not use the USB hub there no problem either, however, I have to use the hub for this configuration that the ports are limited.

  I have this unit used in several parts of my VI, but everything works in series and all instances are completed by closing the VISA resource. If I open just one of the sub - VI which calls the device that I can run indefinitely without any problem on the hub, but for some reason when I use them in the main VI I get this error.

  Has anyone else had this kind of problem or knows how to handle?

  Thank you!

  Hello Jeff,.

  Josh has created a demand for service inside OR to ask for help, so after sent us his code, we noticed that he was using the configure serial port VISA 3 times one after the other, the third VISA configure serial port VI was so poping of the error settings in this VI were does not match the previuosly those configured. After leaving one set up VISA VI serial port in the code, the error disappears.

  Concerning

  Mart G.

• PXI-5402 IVI TestStand 4.2 returned "niFgen_InitWithOptions" resource not found

  Hi, I am very new in TestStand.

  I hope someone could help me.

  I have a complete sequence in which an ivi should initiate a PXI-5402.

  (It is an old sequence that I inherited. It is now my job to make it work again).

  We have another system with a PXI-5401 (appears to the MAX as traditional-DAQ) which works very well with this sequence.

  I created a new sequence in order to simplify troubleshooting with just "IVI Fgen" step.

  When in click on 'Validate' and uncheck "Simulate" and hit "Init", I get:
  niFgen_InitWithOptions returned an error:-1073807343 (0xbfff0011). Insufficient location information or the requested device or resource is not present in the system. If the resource descriptor is a name of IVI, it must match the entry in the store of IVI Configuration in a case-sensitive manner.
  Source: TSIviStepTypes [error Code:-31619]

  In NOR-Spy I get following error
  > Status: 0xBFFF0011 (VI_ERROR_RSRC_NFOUND)

  I think that I have configured all correct. Please see attached screenshot.
  I tried different names IVI-logic...
  For this remove as first cause, I direct the pilot Session that appears correctly on the iviConfiguration of reference.

  Thanks in advance

  OK, I got it...

  This is the well known problem with DAQmx Configuration in MAX.

  Described in the title:

  http://digital.NI.com/public.nsf/allkb/22CF7E6B27B6995B86256DDB0058F39B

  I had post a logic-name link with DAQmx device instead of PXI-Device.

  Thanks anyway.

• Unable to connect to the generator signal with LabView

  Hello

  I use a Tektronix AFG 3021 B signal generator. I installed the National Instruments driver (tkafg3k) for this device. My computer is connected to the signal in the block diagram generator, I place a block called "Example - Getting Started vi". I run the vi (there is no need of connections, so the vi has just the one block).

  The vi then gives me this error:

  Error 1073807343 has occurred to be initialized with Options.vi of tkafg3k
   

  Possible reasons:

  Driver status: (Hex 0xBFFF0011) primary error: error (Hex 0xBFFF0011) - information on the inadequate location or a resource that is not present in the system

  I know that the signal generator properly communicating with the computer because when I run "VISA Resource Manager", I can ask for the name of the device and it returns the correct name.

  -I'm using Labview 8.6.

  -I have NI-VISA installed 4.2

  -The driver that I use is available here: http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=005994E37F5B2318E0440003BA7CCD...

  -J' use the driver that is for version 7.1

  -J' uses this compliance record: http://joule.ni.com/nidu/cds/view/p/id/1095/lang/en

  What is the cause of this error and how can I solve this problem?

  Thank you.

  -Zach

  Do you really need to use the IVI driver, or you can use the LabVIEW driver? If you have need of IVI, configure you the Max with a logical name, etc.

  PS You have posted to the wrong Board. It is for the signal generators of NOR. You should have posted to the Instrument of narcotics control.

• Can't write series base and Read.vi to run

  Hello

  It is a strange problem because I used this .vi including several times before and never had a problem until I have created LabVIEW on my new laptop computer. I installed everything like I should without a problem, but for some reason when I try to run, I get the message:

  "Error-1073807343 is produced in property node (arg 1) visa set up a Serial Port (Instr) .vi-> basic series write and Read.vi.

  Possible reasons:

  VISA: (Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system. "

  I tried to find the error in the forums, but never, it corresponds to what I do and I can't find a solution. It is a problem serious because I'm on a timeline by hand in a project. Please notify.

  Thank you

  Yusif

  Stupid question - is the correct port selected for your new laptop? It's maybe something like com5 instead of com1. Do you see the port in Windows Device Manager?

• Problem with LabVIEW 9.0f2 and VISA 5.0 on Mac OS x 10.6

  Hello

  I'm using MacOSX 10.6 and Labview 9.0f2. I installed the lates VISA (5.0.0) drivers, as they are the only support OSX 10.6.

  Now, I try to run the "basic series write and read" example and get the following error:

  Error 1073807343 has occurred to the property node (arg 1) visa set up a Serial Port (Instr) .vi-> basic series writing and Read.vi

  Possible reasons: VISA: information about insufficient localization (Hex 0xBFFF0011) or the device or resource is not present in the system.

  As I am a newbie to Labview, I'd appreciate any help on this...

  Thank you

  Daniel

  Hello

  You do not have a device series on behalf of resource, you use to write and read and take?

  Did you check with Max OR and log on to this device.

• VISA-1073807343 error code when using ResourceManager.GetLocalManager (). FindResources (filter) to detect the map of Pickering PXI

  I'm upgrading our test system for Windows 7 and NI Developer Suite 2012 DS2 in Windows XP and NI Developer Suite 2008 4th quarter. I have a problem with the help of VISA to detect devices PXI of Pickering. The problem occurs with the next .NET NationalInstruments.VisaNS.ResourceManager.GetLocalManager () call. FindResources (filter). I use the filter "PXI? * INSTR.

  To trouble shoot this problem I was using the VISA program FindResources.2008 c# example. I get the following error message when you apply the "PXI? * INSTR"filter. "Where not enough information or the device or resource is not present in the system. VISA-1073807343 (0xBFFF0011), ErrorResourceNotFound error code.

  Looking at other markets, I infer that VISA is not find the maps. I came across the same error message when I tried to launch the "GPIB? * INSTR"filter however I determined that there was a problem with the NOR-488 driver. 2. after having repaired the driver of the FindResources.2008 program would find the GPIB instruments using the "GPIB? * INSTR"filter.

  Max the Pickering cards appear in "Devices and Interfaces" and are listed as follows:
  12: PCI Device 'PXI12::9:INSTR '.
  15: PCI Device 'PXI13::13:INSTR '.

  In XP, the cards have been identified as:
  PXI12::9:InStr (Pickering 40-785-522)
  PXI13::13:InStr (Pickering 40-780-522)

  Also Max for each device, I am able to open the Panel to Test VISA.

  Any ideas why the VISA is not able to detect these cards?

  Thank you

  I thought about it. Apparently I needed Windows 7 to install the driver for cards of Pickering. I guess the "PXI VPP / VISA drivers" supplied by Pickering Test would take care of this.

  Until Windows has installed the driver of Pickering cards have been listed as a PCI device under 'other devices '. After installation, the cards have been listed under "devices PXI of NI-VISA.

  MAX the card now are listed as:

  12: Pickering 40-785-522 'PXI12::9:INSTR '.
  15: Pickering 40-780-522 'PXI13::13:INSTR '.

• 1073807343 error occurred at niFgen Initialize.vi

  I have questions to the question above.

  I have a SMU Chasis. I swapped the controller to a new brand. (Same model - 8133 SMU). Just the controller has been exchanged and nothing else.

  I wanted to put in place a new and use only the Runtime of LV and the exe file created with LV PERIOD 2009.

  On the new controller, I get this error when I run my application.

  Everything works fine on the former, but the former we have the system full development LV is installed on

  The new controller I get error on:

  It has preinstalled LV DURATION so I have not installed it.

  First, I installed the drivers from the disk of DS2 2010 device drivers OR devices. But I got the error when I tried to run the application.

  I uninstalled the drivers and the insalled former 2010 DS1 (I thought that it might help because these are drivers for LV 2009 SP1, that was used to create the exe file)

  I have the same problem, however.

  The works of exe file it has been tested on many devices but they all had the system of complete development installed on them.

  Any tips?

  I just wanted to post on this topic.

  I had the problem solved, thanks to a person OR support.

  He was bound with one of my cards OR I moved.
  For some reason any on the NEW controller in the MAX I could get 2 instances of the card.

  An asset, a not active.

  I plugged the old joystick and exported its MAX configuration in a file.

  I plugged back the new controller and opened MAX:

  (1) I deleted (deleted) the map OR inactive in the list of MAX

  (2) I imported the permeable contoller configuration form.

  He started working.

• Uninstall software update Apple says error in seller contact package package unstaller

  Try to get itunes working to make a backup of my faulty iphone before repair.

  First-itunes does not start says error. I'm trying to fix it, who said success but same error when you try to start it.

  Then uninstall completely worked. Then reinstall that seemed to be over except for a message "an older version of Apple software update already exists" then he went down and install itunes apparently had not been completed.

  Then I try to remove the update from the apple software and executed by an error in the installation program - it says there is an error in the installation and contact the supplier of the installation package. Same error if I run the uninstall command line program.

  Try to repair the Apple Software Update of programs & features Control Panel and then try to update iTunes again.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  The more information box has direct links with the current and recent if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit - for older video cards) as a workaround for problems with installation or operation, or compatibility with third-party software.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2