Error autour Guru?

Similar Questions

• Pavilion a1320y RC410-m: firmware failure

  This PC is about 10 years old and still works fine. I expect to give it a little more speed with a processor upgrade.

  It is a #ABA ER863AV - 1320y CTO of desktop PC with the original bios.

  AMIBIOS (c) 2005 American Megatrends
  27/01/2006 worm 08.00.12
  Revision of BIOS 3.07

  The HP site says he has a card mother RC410-M Asteropi GL8E (and a slogan on the map says mother RC410-M)

  The HP site says that he accepts the upgrade of processor Pentium 4 651 (from Pentium 4 517)

  There is no update of the bios on the driver page

  When I put the processor 651 in (reset bios default and cleared the CMOS memory)

  I get this error at startup:

  Firmware failure, web site visit the HP to update your BIOS.

  If the problem persists, contact customer support.

  Press F2 to continue

  When I press F2, windows starts normally, but the faster processor with more cache, actually runs slower than the old processor (Windows experience index falls on the processor). The microcode error continues to appear on each boot.

  Hello:

  I don't think there is a way that error autour and IMO, the specs are incorrect.

  I say this because the processor you have installed is released after the date of the BIOS version installed on your PC.

  If you want to take a gamble, a safe bet would be 650 P4, and they are cheap and plentiful on eBay.

  Here is a comparison of the two processors.  The 650 is still less than 2 watts. Same speed, same cache and same FSB

  http://Ark.Intel.com/compare/27483, 27482

  http://www.eBay.com/Sch/computer-components-parts-/175673/i.html?_FROM=R40&_nkw=Pentium+4+650&_sop=15

• MD3000i individual physical disk - gradient path

  Recently, we have replaced a failing in our MD3000i HARD drive. After letting it rebuild, all the disks are again in an optimal state. But the recovery guru still gives this error:

  Individual physical disk - gradient path
  Gradient of physical disk paths:
  Channel: 0
  Physical disks: (unknown)

  Can I support safely on "Check again", or what would be the procedure I should follow to get rid of this error?

  Hello Diss,

  Since you say that when you look in MDSM all readers are also optimal then you should be able to do a recheck out the recovery guru & have it checked to confirm that all the drives are online & optimal.  If after you run the recheck if the cottage no matter what drive as still having problems, then what I would do is to recheck MDSM & confirm that the drive displayed as failed.  The error normally clears once a car has been replaced but in some cases I see need to run check again to clear the error recovery guru.

  Please let us know if you have any other questions.

• MD3220i - firmware update fallito knew a controller

  Ho made upgrade firmware di di a MD3220i alla versione 08.20.16.60.

  E' tutto ok sul primo fits controller, mentre he secondo e fits in error.

  Ho gia SC lo storage e con tried MDSM (version 11.20), one my upgrede del firmware rieffettuare ho UN error recovery guru che indica che nella it module in slot 1 e raid controller in stato "Removed".

  In effetti nel dell ' hardware' TAB ' MDSM nella sezione of pregnant (back) e: empty RAID controller module connector.

  In both realta sono e any modules I riesco dello di pingare 2 place management storage interfaces.

  Buongionro, ha per caso, tried one invertire I controllers?

  Questo comporta he fermo Attività.

  Francesco

• Windows 7 does not recognize my 3 Seagate external drives but is very good with Western Digital and other sticks USB Flash. Windows Vista will see them.

  My apologies if this is a query repeatedly, but I can't find a job anywhere and he leads me into the wall.

  I have 3 external Seagate hard drives. All 3 range from about 3 years 11 months old, 1 TB - 3 TB of capacity, and I use them all from time to time to back up my media. In the past months, my Dell XPS ceased to recognize them, 95% of the time. Sometimes they will be Plug and Play and be fine, but otherwise the result when I plug them is coming the power light and the whirring disc fortunately but nothing on the laptop. They recognized themselves on my other machines running Vista. All other Flash memory devices are very good.

  I also have a hard drive Western Digital external powered, almost identical, that Plug and play every time.

  I tried all my ports and various cables and adapters. I tried them on other machines and they are very good, it seems to be just with my Dell and the Seagates. It recognizes everything that I plug in there from the iPhone to Flash Drives. It has all the latest drivers and Windows updates.

  When they're not working, they do not appear in the devices, disk management, Explorer or UVCView Manager. When they do, all settings appear to be well. My laptop runs Windows 7 Edition Home Premium with Service Pack 1.

  I assigned each their own letter drive, disabled power management and they are not protected by Word. The drivers are the standard Windows ones, because these devices do not use their own. I have the latest chipset drivers, everything works perfectly and is completely up to date.

  When I run UVCView (when one of them does not work), it is said there is an error autour MaxPacketSize, current externally is set to 9 and it said "ERROR: low peripheral speed require bMaxPacketSize0 = 8" branded error. I don't know if this is a factor? This may explain why it's slower transfer data to my machine that has USB3.0 it does on another machine, it begins at 130 MB/s and falls to 30 in 10 seconds.

  I tried all combinations of power off.

  I activated the network detection.

  I uninstalled all the USB in the Device Manager and reinstalled after the start.

  All 3 discs work instantly in my older Vista laptop runing.

  I am a loss to understand. I'm pulling my hair out and I don't have a lot to lose these days! There must be a setting in my computer or on the Seagates but I checked all the usual places and some of the more irritable areas.

  Thank you in advance.

  I'm surprised that the removal of the INFCACHE did not work.  Readers (all external references in fact) were cut at the time, right?  With a reboot after and before you plug anything back?
   
  These instructions really come down to:
   
  Unplug all USB devices other than the keyboard and mouse
  Open C:\Windows\System32\DriverStore
  INFCACHE.1 and rename it INFCACHE.old
  Restart the computer
  Reconnect it (one at a time) each USB device - giving the system about 30 seconds per device to 'catch up '.
   
  If you got on the rest as well your system files are good to go.

• 11g: using jointly Trinidad and Facelets

  Hi all
  
  I'm doing what should be a simple CEP with Facelets and Trinidad, but spin to an obstacle, so I thought I'd post here.
  
  I created a new Web project, select 'none' as the technology of page flow and adding without libraries of tags to the project. As soon as I did this, I'm able to add a new facelets page in my project using the 'all technology' tab on the new gallery. I create the tutorial to 'guess' standard and run - everything works fine.
  
  Now, let's say I want to change the tutorial to "guess" standard to use Trinidad components instead of the h:inputText that uses the tutorial. I add the Trinidad DURATION 11 library to my project and configure the default renderkit in faces-config. XML (without making any changes to the xhtml files at all) and set the alternative display manager in the web.xml file.
  
  At this point, if I try to run the tutorial, I get:
  

  java.lang.IllegalStateException: No RenderingContext
       at org.apache.myfaces.trinidad.render.CoreRenderer.encodeBegin(CoreRenderer.java:194)
       at org.apache.myfaces.trinidadinternal.renderkit.htmlBasic.HtmlFormRenderer.encodeBegin(HtmlFormRenderer.java:56)
       at javax.faces.component.UIComponentBase.encodeBegin(UIComponentBase.java:802)
       at javax.faces.component.UIComponent.encodeAll(UIComponent.java:934)
       at javax.faces.component.UIComponent.encodeAll(UIComponent.java:942)
       at com.sun.facelets.FaceletViewHandler.renderView(FaceletViewHandler.java:577)
       at com.sun.faces.lifecycle.RenderResponsePhase.execute(RenderResponsePhase.java:110)
       at com.sun.faces.lifecycle.Phase.doPhase(Phase.java:100)
       at com.sun.faces.lifecycle.LifecycleImpl.render(LifecycleImpl.java:139)
       at javax.faces.webapp.FacesServlet.service(FacesServlet.java:266)
       at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
       at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
       at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292)
       at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
       at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
       at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)
       at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
       at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3496)
       at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
       at weblogic.security.service.SecurityManager.runAs(Unknown Source)
       at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2180)
       at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2086)
       at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1406)
       at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
       at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)

  This is the first question, so I take the renderkit of faces - config.xml and things seem to work OK again.
  
  For the next test, I add the definition xml ns Trinidad (xmlns:tr = "http://myfaces.apache.org/trinidad") in the file guess.xhtml of the tutorial and test - well Yes, still works.
  
  Now, I change the h:inputText to tr:inputText, h:commandButton to tr:commandButton, h:form to tr:form and h:message to tr:message in the same file and test - no go, I get the same "no rendering context stack trace."
  
  Googling for this error autour don't give me much help, unfortunately.
  
  I decided to try the simple example of the Trinity of wiki page:
  

  <tr:document
     xmlns:ui="http://java.sun.com/jsf/facelets"
     xmlns:h="http://java.sun.com/jsf/html"
     xmlns:f="http://java.sun.com/jsf/core"
     xmlns:tr="http://myfaces.apache.org/trinidad"
     title="Facelets">
  
    <tr:form>
        <tr:inputText label="Your name" id="input1" value="#{backing.name}" />
        <tr:commandButton id="button1" text="press me" action="#{backing.send}" />
    </tr:form>
  
  </tr:document>

  No, same error. How can I replace my web.xml sample one of the Trinity wiki... No, not does more :(
  
  Same deal if I add JSF to my scope of technology (who, incidentally, will let me create new facelets pages).
  
  Finally, in desperation, I add the taglibs Trinidad my project and get this mess:
  

  java.lang.NoSuchMethodError: javax.faces.context.ExternalContext.setRequest(Ljava/lang/Object;)V
       at org.apache.myfaces.trinidadinternal.config.GlobalConfiguratorImpl._isSetRequestBugPresent(GlobalConfiguratorImpl.java:543)
       at org.apache.myfaces.trinidadinternal.config.GlobalConfiguratorImpl.getExternalContext(GlobalConfiguratorImpl.java:325)
       at org.apache.myfaces.trinidadinternal.context.FacesContextFactoryImpl$CacheRenderKit.(FacesContextFactoryImpl.java:86)
       at org.apache.myfaces.trinidadinternal.context.FacesContextFactoryImpl.getFacesContext(FacesContextFactoryImpl.java:64)
       at org.apache.myfaces.trinidadinternal.context.FacesContextFactoryImpl.getFacesContext(FacesContextFactoryImpl.java:64)
       at javax.faces.webapp.FacesServlet.service(FacesServlet.java:208)
       at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
       at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
       at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292)
       at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
       at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
       at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._invokeDoFilter(TrinidadFilterImpl.java:239)
       at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:196)
       at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:139)
       at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92)
       at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
       at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3496)
       at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
       at weblogic.security.service.SecurityManager.runAs(Unknown Source)
       at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2180)
       at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2086)
       at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1406)
       at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
       at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)

  Any help on no defuddling my brain on this one?
  
  John

  Hi John,.

  What wiki page were you using? http://wiki.Apache.org/MyFaces/Facelets_with_Trinidad?

  Also, make sure that you have to follow (also mentioned in the wiki):
  faces-config. XML

  You don't need to configure any specials to use Facelets with Trinidad. Do not add the FaceletsViewHandler here! But make sure you have the ID of Trinidad RenderKit in this file, like:

  
  
  
  org. Apache.MyFaces.Trinidad.Core
  
  

  and

  Web.Xml
  
  org.apache.myfaces.trinidad.ALTERNATE_VIEW_HANDLER
  com.sun.facelets.FaceletViewHandler
  

  Kind regards

  ~ Simon

• This error message will let me install a 3rd party app. need a guru. Help me ob1.

  I get this error whenever I try to run the Setup program on a particular application.

  could not load the dll library c:\documents and owner documents\palm os desktop\userdata.dll.  the specified module could not be found.

  I did a chat with a palm representative session and he could not help.  the application provider is unable to help either.

  Thanks in advance...

  just do what you informed and again got the message.  then tried something that I should have last week.  I did a search for the missing .dll file and found in the right folder under palm os.  copied to the appropriate folder and it worked perfectly.

  Thanks for your help.

• Tecra R940-1EE - dead with lead error 4Eh

  Hello.

  Last night without any warning my laptop has stopped working. I tried with and without battery, press the button turn off for 20-30 seconds without battery, with battery, without the CC adapter, etc.
  The error code I get on power led (flashes orange) is 01001110 - 4Eh.

  Is one knows what means this error? I'm sure that this is a power related issue, but I'm not able to find what the error codes.

  Thank you

  Hello

  Autour Googling, I found the info the error codes 4 * h means that there is an error with the S3V out.
  There is no code 4Eh 4Eh.

  Just follow codes are available:
  40 h tension S3V is on 3.47V.
  45 h S3Vvoltage is less 3.14V.
  46 h blood S3V is under 3.14V or less when the computer starts up.

  That's all I found online in various forums.

• Satellite P100 - 307 Error Message: "failed to get read handle.

  "Failed to get read handle." Error message that appears whenever I start my laptop. HELP, its boring

  Error message that reads "Failed to get read handle." lies at the heart of my screen. Strange that it has an OK button, which means that the computer expects me to think it's ok. It's like the 'So what' button which really did not help them that my computer failed to get read manages? How can I get rid of this message? And why he's here.

  It's like setting up a new cell phone and the first time you receive your new number to a text message comes on the screen saying "Otta OK." Who the hell is Otta and what was wrong with Otta initially. In any case, anyone could help me with this, I would of course welcome.

  Hi Thorsten

  My first question is; What to hell you have on your laptop?
  I never saw the message as "Failed to get read handle."
  I have goggled autour and nothing!

  Are you able to get into the operating system? O If yes try to restore the operating system to the beginning.
  I put t know what you have installed or not installed on the device but I can t believe this is happening without any reason.

• Error constant csc.exe 550 d NB during the shut down

  Hello!

  Got a new Toshiba mini netbook today and here is my problem:
  I always get an error of csc.exe when close my completely new installed windows7.
  Install microsoft .net cadre4 - as always suggested - does not solve the problem.
  Someone here to help me?

  Hello

  I put t I have this problem, but internet is full of discussion that is this csc.exe and how to solve.
  Have you tried Googling autour solution?

  Try http://www.cscexe.com/ or http://www.sevenforums.com/software/124278-csc-exe.html

  Please send comments.

• Satellite 1800-400, ERROR! F3D failed

  Someone can help me troubleshoot above?
  First of all what does this mean?
  I had a very small Satellite 1800-400 with me running. I was convinced that it was full of viruses so wanted to start all over again with the recovery disk. All I got was this error.
  In addition, it is said software being installed, please wait and a 0-100% bar. (nothing happens)
  Being a novice surf autour, I picked up a new BIOS @ this site. After the install was not successful so I used the command chgbiosa on the a:\, this gave me a command prompt to enter the biosfile in and I have upgraded to version 2.2 (I really thought he could help silly)
  Retry the recovery disk didn't give no solution so I'm really looking forward to all the solutions to this disaster.

  Hi sms,.

  Sounds strange! Is the recovery CD in good condition? Is this perhaps a scratch?

  Goodbye Tom

• Qosmio F20 - 437 Application error

  Hello

  I use the recovery disk to restore my Qosmio F20 to factory settings, an application error 437 a popoed upward during the reimageing process.
  I remember upgrading the RAM, and I don't have the original with me.

  Any help will be appreciated.
  Thank you.

  Hello

  Autour Googling, I found thisarticle.

  So I ask what may be the solution to your problem. May be corrupt drive recovery? Can you see scratches or stains on it?

• Satellite L750 - Director Windows starts with the E945000E error code

  Satellite L750 (PSK1WA-03c00R)
  4gig

  Hello

  Previously, I had windows essensials and used Director!

  I had my hard drive empty and reinstalled Windows 7 and some web Toshiba drivers to start all over again!

  I have redownloaded Movie maker and now get this error message "error code window movie maker c945000e.

  He said that I might need to update my video card driver! Problem is that I can't see all downloads for video card on the Satellite L750 download page?

  I have Intel HD 3000 family video card! But since I've started using movie maker my CPU had slowed down somewhat and was part of the reason restore my hard drive! I think I just have too many things in the background!

  I can do the basic CPU features but a guru IT Im not! Can someone help me or explain what I could do to solve the problem in laymens terms!

  Post edited by: tony73 update of what I use the video card

  Did you notice the same problem when using original Windows 64-bit Home Premium that you got with your laptop?

  Generally speaking, it is Microsoft related question and best explanation to this problem, I found here.

  You have the Australian mobile phone model and drivers download page you can find on http://www.mytoshiba.com.au/support/download
  > I previously had windows essensials and used Director!
  By the way: do you use the same version as before?

• On Qosmio F45-AV411 errors Windows Update

  Hi all

  Below the discussion with me and the microsoft support on the problem to my laptop.
  What can I do next? Thank you very much.

  Hi Jon,

  Thank you for your response and delayed apology.
  After that I will review the outcome of the System File Checker, it shows that there are corrupted files in impossible to remedy Windows and Windows system files. So the next step is no choice for the repair of Windows and if you have a computer of OEM manufacturer I'm afraid that you do not have to have.

  You should ask the manufacturer of your computer to this Windows repair. If they're going to ask you to make a Windows Recovery please backup all your important files, as he'll recover your computer originally manufacture settings.
  Thank you for your cooperation.
  Your patience is much appreciated.

  Kind regards
  Agung Berbudi
  Online technical support Microsoft South East Asia
  http://support.Microsoft.com

  Dear love, thank you very much for your suggestion. This is the result in the attachment. What can I do next? Thank you very much.

  Best regards, Jon

  Sea, 12/17/08, Agung Berbudi
  From: Agung Berbudi

  Hi Jon,

  Thank you for your reply and appreciate for all information you is provided. As you can see below, your Windows Update failed with the majority two 0x80072ee2 and 0x8024402F error code (AutomaticUpdates software failure Windows Update Sync Client has not detected)

  2008-12-17 02:24:42:647 1248 11 c 0 Misc WARNING: WinHttp: httpRead failed. error 0x80072ee2
  2008-12-17 02:24:42:647 1248 11 c 0 Misc WARNING: WinHttp: DoFileDownload PerformDownload failed. error 0x80072ee2
  2008-12-17 02:26:49:068 1248 11 c 0 Misc WARNING: WinHttp: httpRead failed. error 0x80072ee2
  2008-12-17 02:26:49:068 1248 11 c 0 Misc WARNING: WinHttp: DoFileDownload PerformDownload failed. error 0x80072ee2
  2008-12-17 02:28:50:562 1248 11 c 0 Misc WARNING: WinHttp: httpRead failed. error 0x80072ee2
  2008-12-17 02:28:50:562 1248 11 c 0 Misc WARNING: WinHttp: DoFileDownload PerformDownload failed. error 0x80072ee2
  2008-12-17 02:30:53:412 1248 11 c 0 Misc WARNING: WinHttp: httpRead failed. error 0x80072ee2
  2008-12-17 02:30:53:412 1248 11 c 0 Misc WARNING: WinHttp: DoFileDownload PerformDownload failed. error 0x80072ee2
  2008-12-17 02:30:53:412 1248 11 c 0 PT WARNING: ECP: impossible to download the cab of http://download.windowsupdate.com/msdownload/update/software/dflt/2008/08/1482251_2efbea463be5fa586ebf8f6b1b011fb5451fb501.c ab
  with error 0x80072ee2

  2008-12-17 02:30:53:413 1248 11 c 0 PT WARNING: ECP: this trip contained some optimized updates failed. New number of update = 1, old Count = 10
  2008-12-17 02:31:01:245 1248 11 c 0 PT WARNING: synchronization of updates: 0x8024402f
  2008-12-17 02:31:01:245 1248 11 c 0 PT WARNING: SyncServerUpdatesInternal failed: 0x8024402f
  2008-12-17 02:31:01:246 1248 11 c 0 Agent * WARNING: could not synchronize, error = 0x8024402F
  2008-12-17 02:31:01:264 1248 11 c 0 Agent * WARNING: exit code = 0x8024402F
  2008-12-17 02:31:01:265 1248 11 c 0 Agent *.
  2008-12-17 02:31:01:265 1248 11 0 Agent c * END * Agent: finding updates [CallerId = AutomaticUpdates]
  2008-12-17 02:31:01:265 1248 11 c 0 Agent *.
  2008-12-17 02:31:01:265 1248 11 c 0 Agent WARNING: customer WU didn't search for the update with error 0x8024402f
  2008-12-17 02:31:01:289 1248 74 c to THE > # RETURN # to THE: research updates [CallId = {B8DB0DAA-4B3A-4F8A-8326-3C2E0C426033}]
  2008-12-17 02:31:01:290 1248 74 c# WARNING: reminder of search failed, result = 0x8024402F
  2008-12-17 02:31:01:290 1248 74 c# WARNING: could not find updates with error 8024402F code
  2008-12-17 02:31:01:290 1248 74 c to THE #.
  2008-12-17 02:31:01:290 1248 74 c# end # in THE: research updates [CallId = {B8DB0DAA-4B3A-4F8A-8326-3C2E0C426033}]
  2008-12-17 02:31:01:290 1248 74 c to THE #.
  2008-12-17 02:31:01:293 1248 74 c to THE setting next detection timeout at 2008-12-16 20:31:01
  2008-12-17 02:31:01:294 1248 74 c time of installation to THE adjustment to THE planned at 2008-12-17 09:00

  2008-12-17 02:31:06:300 1248 11 c 0 report REPORT EVENT: {441E306B-86A2-4302-A25E-BCD097906114} 2008-12-17 + 1100 1 148 101 02:31:01:264 {00000000-0000-0000-0000-000000000000} 0 software AutomaticUpdates failure 8024402f from Windows Update Client sync did not detect with error 0x8024402f.

  And I can see that you can not run the System File Checker and verify the disc because that do not have enough privilege to perform these actions. Now you can try to run the System File Checker and Windows safe mode disc, check

  1. turn off your computer.
  2 turn on the computer and when the POST (Power On Self Test) is completed, press the F8 key until you see Windows advance Options menu.
  3. select Safe Mode, and then press enter two times.
  4. connect to your administrator account.
  5. run the System File Checker, and check the disc.

  May I know the results updating form new account?

  Please let me know the results

  Thank you for your cooperation. Your patience is much appreciated.

  Kind regards
  Agung Berbudi
  http://support.Microsoft.com
  From: Jon Afrizal

  Dear love,

  Sorry Agung, I send you many files, because I sent you the wrong file format.

  Best regards
  Jon

  On Tue, 16/12/08, Agung Berbudi
  wrote:

  Dear Jon,

  This is Budi Microsoft's technical support and I will continue to help you on this question, as Ali Will be absent for a week. Thanks for your response and like to update on the situation. Understand that you may have a chance with all the previous suggestion of my colleague. At this point, I will provide you with another work autour for you to try.

  Initially, please send me your Windows Update log:

  Collect the WindowsUpdate.log

  1. Please click "Start", double-click it to open the Local disc c, navigate to the "C:\Windows" folder, right-click on WindowsUpdate.log and choose "copy".
  2 right-click on the free space of the desktop, choose "Paste".
  When the user account dialog box appears, please click "Continue" if necessary.
  3. a WindowsUpdate.log right click on the desktop, choose "send to"-> "compressed file (zipped).

  Please send these zip files to [email protected]

  Suggestion 1: Run chkdsk /r and sfc/scannow

  1. start (Windows Logo)-> all programs-> Accessories
  2. right click on command prompt-> choose 'run as administrator '.
  3. when the command prompt window displays the type

  Chkdsk /r-> press ENTER, let windows check your hard drive error (follow the procedure until its finished)

  Chkdsk /r - check HARD drive and fix errors, locates bad sectors, and recover readable information

  sfc / scannow-> press ENTER, (follow the procedure until its finished) sfc/scannow verifies the authenticity of the file system and replace the files that have been corrupted.

  Please let me know the outcome of these orders and send me the screenshot of it. If the problem persists, you can run the following suggestion

  Suggestion 2: Create new user account.

  1. Click Start and select Control Panel.
  2. click on user accounts and family safety.
  3. in respect of user accounts, click Add or remove user accounts.
  4. click on create a new account.
  5. Enter the name of the account. Select the account type: Standard or administrator.
  6. click on create account.

  more information on how to create a new user account, please check with mentor or refer to http://support.microsoft.com/kb/279783
  If you have any questions or concerns about the information that I have provided, please do not hesitate to let me know.
  It is my pleasure to be useful and I look forward to hear from you.

  Kind regards
  Agung Berbudi

  First I put t understand why post you the history of all email in this forum.
  I put t think that s useful for everyone here

  However, it seems that the guys at Microsoft couldn't t help and that's why it seems that your Windows operating system is really confused until

  If your OS is confused upward then ONLY reinstall new would be really useful and recommended.

  So take your recovery disk and the operating system to restore to the factory settings.
  Then try to update the operating system.

  Concerning

• Equium A100: Disc D is not accessible - i/o device error

  I recently bought a box of 50 masterpieces of Mozart CD. I want them on my drive hard, but every so often, I hear the whirring autour CD in drive D: but it then stops and no further action takes place. Equium A100 does not recognize the disc: no disc in drive D:! If I go to my computer and click on D:, I get a warning "D:\ is not available..." I/o device error."

  This only happens with certain CD; others are fine. Could I do something wrong? Any help would be appreciated.

  Peter

  Hello

  > This happens only with CDs; others are fine. Could I do something wrong?

  Hmm in my knowledge, not all CD and DVD are compatible and taken in charge and sometimes could happen that the drive can not read some CD.
  It is not impossible

  Maybe the firmware of the installed disk does contain all the details of manufacturing of CDs and properties and, therefore, the lens of the drive can not calibrate and manage the inserted CD.

  I found in my manual to the user a list of CD and DVD compatible and supported.
  There you should find the different manufacturers that produce a compatible media.