error DVD 69889 drive

Similar Questions

• Cannot install windows 7-error: dvd/cd driver missing

  Try to install Windows 7 on a different SSD, but get an error indicating that the missing required cd/dvd driver.  How Windows load into memory from a cd/dvd that windows 7 says there is no driver missing?  This is the same installation disc that I used on a previous SSD without problem.  I have 2 other unused installation floppies, and each returns the error message.  This problem arose when an attempt to use System Restore Image I had done just on an external SSD and a drive hard usb.  The error I had to try to use one of them was that the Image was made in EFI and the computer seeks to restore in BIOS. It's the same machine.  Yes, disk management displays the UEFI 100 MB system partition.  The motherboard is an Asus F2A85 - V Pro.  List Disk running installation diisk sees only the cd/dvd and the drive hard usb but not the SATA drives.  When you normally use that List Disk sees everything.  The UEFI bios sees all readers, when you use the system installation disk.  I used a system repair disc made from the same computer at the same time as the picture of the system and used to start and got a system repair options is not compatible with this version of windows.  The windows version is 6.1.7601 sp 1 build 7601.  Any ideas?

  Hello

  Thank you for your response.

  There are two modes of starting particularly machine-> BIOS & EFI. BIOS is the general start mechanism found in most machines. Some of the machines also support EFI boot mechanism with BIOS

  Either the BIOS or EFI is set as the default in your machine - Please check start the installation system which

  one is active by default.

  If the EFI operating system is installed, it will create an EFI system partition in your machine. Installation of BIOS has no EFI partition.

  Warning in the BIOS: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful. Please feel free to post in the case where you are facing other problems with Windows, we will be happy to help you.

• Satellite 1400: I get IDE-error after upgrade to the slimeline DVD - RW drive

  I have the laptop with a DVD-ROM above it. (Second hand and no manual)
  I have a DVD - RW Drive (SOSW - 852S) I would use.

  I can adapt without any problems.

  It freezes on the spot but for about 2 minutes and then it says IDE-error then it it boot XP.

  When I go into my computer there is no DVD player.
  Have I missed something when I put the disc?
  I can't? t get the BIOS to check it out.

  I tried most of the buttons for example F2.

  Hi David

  It s a clear case for all those who have a little experience with mobile technology.
  You must know that not every drive slimeline is compatible and supported with the device.
  The Player supports uneditable master / slave or c - salt settings.

  In your case, the laptop freezes 2 minutes because the BIOS trying to find STRANGE.
  This is not possible because of wrong settings and pops up the error IDE.

• CD-ROM/DVD-rom drives will not play discs?... tried to be updated no joy... I tried the uninstall then re install just says code 39 error?. any suggestions?

  CD-ROM/DVD-rom drives will not play discs?... tried to be updated no joy... I tried the uninstall then re install just says code 39 error?. any suggestions?

  Try following the steps under "Windows XP" in the article following the MS KB:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• Cannot eject cd studio 1555: error: an error has occurred by ejecting ' DVD RW drive (D :)

  Im making a back up and I can't not to eject cd No 2 using the computer and then ejected.   my keyboard eject button does not work either.   It says "Microsoft Windows reports: an error occurred by ejecting"Player DVD RW Drive (d)"someone knows how to eject manually?

  There is a PIN on the front of the drive hole, use a paperclip, pushed inside enough to jump the gate, you can then pull it fully open.

• DVD RW drive has an error code of registry 19. I can't use the drive and it is not visible as a drive.

  My lite - on dvdrw lh-20a1l ata device does not work.  Device Manager appears with the following text:

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I tried looking for solutions, uninstall driver and reboot, reinstall the software provided with the machine, running regecure software to clean the registry and nothing has solved the problem so far - you have ideas?

  19 code means there is a driver conflict such as two devices attempt to use the same
  resources.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then check the cables
  both ends. Remove and replace, do not just tight. For laptops, you can often clean the
  power and data of the contacts with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the system manufacturer
  and the manufacturer of the device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD &)
  Burn DVDs and CDs and read DVDs). So it is not unusual for 1 or 2 operational parts while
  others do it properly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Error ""A required CD/DVD device driver is missing. " If you have a flash drive driver floppy disk, CD, DVD, or USB, please insert it now.

  OriginalTitle:lack drivers

  I change my ubuntu to Windows 7, but "A required CD/DVD device driver is missing. If you have a driver on floppy disk, CD, DVD, or USB flash drive, please insert it now. Note. If the windows installation media is in the drive, you can remove it for this step. "what I can do about it?

  Hello

  Are you able to boot to the Windows Vista operating system?

  Read the following article and see if that helps:

  Error: A required CD/DVD device driver is missing - when you boot Windows 7 or Windows Vista installation disk:

  http://support.Microsoft.com/kb/952951

• How can you correct - an error occurred in ejecting ' DVD RW drive (e) "."

  I was wondering what is happening. Works perfectly an hour ago now, it does not respond when I press the button to eject the trey. When I try right click then eject it comes with, an error occurred while ejecting ' DVD RW drive (e) "." What is happening to her?

  Hi Scorpion1138,

  Please use the forum.

  Quick question, have you tried to reboot your PC and eject the DVD until windows loads? It might just not be well wedged into the slot.

  Give that a try and let us know if it worked for you.

  JohnD
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• DVD/RW drive has a corrupt... driver error 39

  DVD/RW drive has a corrupt... driver error 39

  How to replace this driver
  Device Manager indicates that the driver is the best available
  The device is Optiarc DVD +-RW AD - 5560 a ATA

  Hello

  Please see the troubleshooting steps in this link...

  http://support.Microsoft.com/kb/314060

  .. do not run the fixit which is only for XP and Vista. Please report back with the results of your troubleshooting operations.

  Tricky

• Error message from device IO on the DVD ram drive

  Help someone!
  I have a Satellite S203 and recently the em * a DVD ram drive stopped recognize any kind of CD/DVD, etc.. It must much worse & worse over time with her works do not at all. I tried to change the configuration of the IDE to PIO but always without success. Help, please...

  Jelibabi

  Hello

  Sorry, but I don t know what laptop you have (xxx-S203) but I can tell you that DMA if available is standard setting for all Toshiba laptops. On this path, it is not easy to give you a correct answer, but if the reader can't read original CD or DVD I guess there is hardware malfunction and the drive needs to be replaced.

  Good bye

• HP Zbook Studio G3: error cd/dvd device driver missing

  Hello guys,.

  When I try to install windows 7 Enterprise 64-bit on Zbook Studio G3, I get the lack cd/dvd device driver. I tried all the possible drivers, but no luck

  Any help would be appreciated

  Thank you

  concerning

  Generally, it is an indication that the you use the Windows 7 installation media that is inserted in a USB3.0 port. Windows 7 is not supported with native support for USB3.0 and requires the installed USB 2.0 port or a USB3.0 port emulation USB 2.0. In addition, there may be issues when you try to install Windows 7 on an Intel SkyLake chipset.

  The first step would be to go through the BIOS and see if there is an option for the compatible mode or emulation for USB ports.

  Alternatively, you can contact HP to see if they have material recovery/restore for Windows 7 to your computer.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Windows Media Center cannot detect the error DVD Windows Media Center cannot detect a DVD in the DVD - ROM drive. Insert a video DVD into the drive

  Original title: why Windows Media Center does not detect my DVD?

  I built my computer motherboard ASUS P658D, Intel i7 processor clocked at 2.6 gHz, 12 GB RAM, 750W Corsair PWR. power, Windows 7 Home Premium 64 - bit & ie9. When I put or the other two DVDs in one of two DVD players, Windows Media Center appears and when I click on "Play DVD" Media Center give me a window that says:

  "Windows Media Center cannot detect a DVD in the DVD - ROM drive. Insert a video DVD in the drive." Two DVDs, I've tried are educational for DVD

  my Nikon D300 Digital camera and a family video DVD or both these very well play in a bed of same computer running Windows 7 Professional 64-bit, & ie8.

  I tried Microsoft Fixit, no help. I tried to send Microsoft Support, and I got NO HELP. I did not bring any changes, and installed any program, just

  scoured the internet. A DVD player is a Sony Optarc with Microsoft Driver, the other is ASUS. I also tried to use Windows Media Player but nothing

  rises or it returns me to Windows Media Center and it does not detect to play either of my DVD. How can I get help here, or from Microsoft? Thank you.

  No, there is no yellow warning in Device Manager and the device manager says that two DVD players work properly. Mr. Fix it's

  automated download from microsoft that is supposed to automatically fix some problems, but he provided no help here. I think it is more likely

  that there is a problem with Windows Media Center or Windows 7 Pro 64 bit and either of my two new Sony DVD drives

  and ASUS.

  I thought my way in a solution. My thought was: Device Manager indicates DVD players work properly and both are new and we're Sony, and the other ASUS so I think only an unlikely problem with readers. The problem is with Windows Media Center "do DETECTED is not the DVD. So there must be a problem with Windows Media Center. I thought that I might need to reinstall Windows 7... then I thought that maybe if I just reinstall Windows Media that will work. He did. My problem was:

  Start > Panel > programs and features > features on or off Windows activate > then uncheck the box for multimedia functions > restart the computer > and then re-check the box to restore the multimedia features > now both discs play both DVDs, I tried. Both disks are operating normally. Reinstall the characteristics of media Windows 7 resolved the problem. Thanks to all who offered solutions.

• P50-A-144 satellite: the CD-ROM/DVD-ROM drive does not

  Version of Windows 10 Home 1607 (Build 14393.187)

  Hello

  After Windows Update Version 1511 1607, the CD-ROM/DVD-ROM drive does not work.
  The D: drive does not appear in Windows Explorer,
  CD-Audios and videos / DVDs do not work.

  In the Device Manager, the following legacy status error message appear:
  "Windows cannot start this hardware device because its configuration information.
  (in the registry) is incomplete or damaged. (Code 19). »

  Could you tell me how to solve this problem?
  Thank you.

  The solution was to uninstall the program "Toshiba Recovery Media Creator' and system settings/Programm features.
  I still don't understand why, but the fact is that after uninstalling the CD-ROM/DVD-ROM start normal work.

  More information here:
  http://www.borncity.com/blog/2007/08...-verschwunden/

• Satellite P20 DVD ROM drive may not be recognized

  Hello

  I just replaced my DVD ROM drive, but I had a problem.
  It is a new DVD rom drive I ordered at TOSHIBA also.
  It could not be detected by Windows:
  -Tried to check on Device Manager, not detected
  -Tried to reload the driver, the same problem
  Note:
  Whenever I tried to re - insert the disc, the blue light in the control panel of my P20 beds (I understand, which means that the P20 detects the drive) but I don't understand, is that why Windows XP does not detect it or it does not alarm or error messages.

  Any help?

  Thank you

  Hello

  Try to use the Add Hardware option.
  This question is very strange, but I read on some sites, sometimes a whole new OS install CD player, brings back to life.

• Equium L40 DVD Multi drive - do not burn files to DVD

  Hello

  Whenever I try to burn files to DVD discs using my dvd/rw drive, it holds in check the same point and comes with the invalid 'MS-DOS function' error. CDs write very well that it's just the DVD.

  Please could someone help with this problem?

  Equium L40 series
  Vista operating system
  My * a DVD-RAM UJ-850 s

  Hello

  What burning software did you use?

  I use Nero, and I've never had any problems!