error of switching EBU

Similar Questions

• Error on switch Dell N3024

  Dear all,

  I already configure switch Dell N3024P it pops up an error in the command line (CLI) like this:

  <187>Mar 17 21:40:13 ARM_CORE_1 - 1 DRIVER [bcmDPC]: broad_hpc_drv.c (4428) 1169 %% unit: 0
  CDC RX FIFO error table entry 0 19 ECC

  When I check in the internet there is someone said that there is an error of memory, - is it true?

  And then how to fix the error?

  Please please need your help.

  Thanks before.

  The firmware is applied to the stack master. The rest of the switches is synchronized to the master firmware version. But the whole stack will require a restart before the new image is active. Page 31 of this stacking guide goes into more details on the process.

  http://Dell.to/1TGe3rM

• PIX 506 error VLAN switch

  Hello

  I meet a few small problems with a v6.3 (4) pix 506 and 2924c-xl switch.

  On the switch for the pix port, many input errors and Runts appear.

  On the pix, there is a VLAN configured and the trunk port is configured as

  mentioned in the Release Notes for Pix.

  I could not find a bad configuration here, but maybe someone has an idea how to

  solve this problem.

  Thank you

  just a few lines:

  [pix]

  Auto interface ethernet1

  physical interface ethernet1 vlan2

  logical interface ethernet1 vlan999

  [go]

  interface FastEthernet0/1

  PIX506 description

  switchport trunk encapsulation dot1q

  switchport mode trunk

  spanning tree portfast

  No cdp enable

  interface VLAN2

  IP x.x.x.x 255.255.255.0

  no ip directed broadcast to the

  no ip route cache

  Hello

  Do you find some useful info on the Runts on 802. 1 q port.

  Runts on an 802. 1 q trunk port.

  A catalyst 2900XL or 3500XL that receives a frame of 802 bytes. 1 q encapsulated 64 or 66 on a port trunk counts as a runt. However, it continues to transfer the weft.

  This issue occurs when you connect to the Cisco 7960 IP phones switch when using a VLAN auxiliary (voice).

  This issue is cosmetic and because of an ASIC limitation.

  It should not cause any degradation in the performance of the switch.

  For more information, see Cisco ID CSCds32999 bug (only for registered customers).

  Cisco IOS Software version 12.0 (5.4) WC1 or later

  On the errors of entry...

  Entry errors

  Entry mistakes provide a count of errors that occurred when trying to get packages from this port. The meter includes errors CRC and the framework. However, it does not include ignored packets. It is a list of entry errors:

  CRC errors: Occur when the packets received fail the CRC check.

  Frame errors: occur when the receiver frame is not complete.

  Ignored Counter: Account number of frames dropped on entry due to depletion of resources in the switch fabric.

  Meter overruns: occurs when interframe gap (IFG) are too short. In this case, a new Ethernet frame arrives before the previous one is completely stored in the shared memory.

  http://www.Cisco.com/en/us/products/hw/switches/ps607/products_tech_note09186a0080125913.shtml

  regds

• Dreamweaver 6.1 - JavaScript error when switching between open tabs

  When you switch between open tabs, occurs a series of javascript errors. I had not used Dreamweaver for about 2 weeks, and the last time that I used it without any problems.
  
  I tried to uninstall, OKing deleting all files when asked, re - install and update with dwmx61_updater.exe, but I still get the same errors.
  
  This made it virtually unusable software, so any help would be greatly appreciated, as I'm working to a deadline approaches quickly.
  
  
  'While executing Browse_Back activated within toolbars.xml, a JavaScript error has occurred"
  followed by
  'While executing Browse_Forward activated within toolbars.xml, a JavaScript error has occurred"
  followed by
  'While executing Browse_Stop activated within toolbars.xml, a JavaScript error has occurred"
  
  The code seems to be:
  
  <!--> browser nav toolbar
  
  < id toolbar = "Browser_Toolbar" platform = "win" label = "Browser Navigation" container = 'document' initiallyVisible = "false" >
  
  < id button = "Browse_Back."
  image="toolbars/images/mm/back.gif".
  disabledImage="Toolbars/images/MM/back_dis.gif".
  ToolTip = 'return '.
  Label = 'return '.
  Enabled = "DW.getDocumentDOM (). Browser.isCmdEnabled ('back').
  Command = "DW.getDocumentDOM (). Browser.backPage ().
  Update = "onEveryIdle" / >
  
  < id button = "Browse_Forward."
  image="toolbars/images/mm/forward.gif".
  disabledImage="Toolbars/images/MM/forward_dis.gif".
  ToolTip = "forward".
  label = "forward".
  Enabled = "DW.getDocumentDOM (). Browser.isCmdEnabled ('forward').
  Command = "DW.getDocumentDOM (). Browser.forwardPage ().
  Update = "onEveryIdle" / >
  
  < id button = "Browse_Stop."
  image="toolbars/images/mm/stop.gif".
  disabledImage="Toolbars/images/MM/stop_dis.gif".
  ToolTip = "Stop".
  label = "Stop".
  Enabled = "DW.getDocumentDOM (). Browser.getPageBusy ().
  Command = "DW.getDocumentDOM (). Browser.stopPage ().
  Update = "onBrowserPageBusyChange" / >
  
  < id button = "Browse_Refresh."
  image="toolbars/images/mm/browserRefresh.gif".
  ToolTip = "refresh."
  label = "refresh."
  enabled = "true".
  Command = "DW.getDocumentDOM (). Browser.refreshPage () "/ >"
  
  
  
  probably the next error is caused by the previous ones have failed:
  
  "While running to getCurrentValue in AddressURL.htm, a JavaScript error occurred"
  the subprojects tcode:
  
  
  getCurrentValue() function
  {
  var dom = DW.getDocumentDOM ();
  var value = dom.browser.getURL ();
  If (value & & value.length)
  {
  check if it isn't a temp file
  excerpt from the tail of the url
  var filename = value;
  var slashIndex = filename.lastIndexOf("/");
  filename = filename.substring (slashIndex + 1);
  var tempIndex = filename.indexOf ("TMP");
  If (tempIndex! = 0)
  {
  addRecentAddress (value);
  }
  }
  Returns the value;
  }
  

  Out of curiosity, I uninstalled IE7 beta 3, as it was the only program I thought that may be important that has been installed since last Dreamweaver work properly - and guess what? -the problem disappeared!

  Thanks again for your help - I hope this topic can be useful to someone else.

• I'm trying to start using the compatibility feature, the display settings for Starcraft: run in 256 colors, run in 640 x 480 screen resolution... I get an error__It tries to start and modes then errors on switch...

  The error has occurred trying to change the video mode was:
  It is not implemented
  vidinimo_PC.cpp line 160
  SetDisplayMode

  Dell Inspiron 1010; Intel Atom; @1 Z530 CPU. 60 GHz; Windows XP

  Hello

  Hoping that the Direct X is updated, if not update DirectX first and then try the following:

  Reduce hardware acceleration can help you:

  -To disable or reduce the hardware acceleration on your computer, perform the following steps:

  Click Start in the lower left corner of Windows Vista.
  Click Control Panel, click appearance and personalization, click personalization, click display settings and then click Advanced settings.
  Click the Troubleshooting tab, and then click on change settings.

  Note: The settings will be disabled if the graphics card driver does not support disabling hardware acceleration.

  Move the hardware acceleration slider until it is one notch to the right of none. It is the basis of acceleration.

  Click OK twice, and then close the window.

  -Try the latest patch from Blizzard.
  http://us.Blizzard.c...MP;PageNumber=1

  Good luck $

• Get the error when switching from table

  
  Hi all

  I'm moving my procedure table values but no luck. your help in this regard will be highly appreciated. Thanks in advance.

  I created the following procedure:

  -------------

  CREATE OR REPLACE PROCEDURE send_coll

  IS

  TYPE c_dept_no IS TABLE OF THE dept.deptno%TYPE;

  v_dept_no c_dept_no: = c_dept_no();

  BEGIN

  SELECT DeptNo

  TO COLLECT FEES IN BULK

  IN v_dept_no

  EMP;

  END;

  ------------------------

  Now, I want to spend all the values of v_dept_no to one of my name of the procedure as rec_coll that receives the value of v_dept_no and print the value against v_dept_no. for example:

  When v_dept_no = 10 then print all empno against deptno 10 and so on...

  I think I have to do something like below but no luck so far.

  CREATE OR REPLACE PROCEDURE send_coll

  IS

  TYPE c_dept_no IS TABLE OF THE dept.deptno%TYPE;

  v_dept_no c_dept_no: = c_dept_no();

  BEGIN

  SELECT DeptNo

  TO COLLECT FEES IN BULK

  IN v_dept_no

  EMP;

  I'm looping 1.v_dept_no

  rec_coll (v_dept_no (i)); - call the rec_coll procedure and pass in the value

  end loop;

  end;

  ---------------

  create another procedure that will receive the value for v_dept_no

  ------------

  CREATE OR REPLACE PROCEDURE rec_coll (v_emp_no c_dept_no) - create collection with c_dept_no type

  IS

  BEGIN

  I'm looping 1.v_emp_no.count

  dbms_output.put_line (v_emp_no (i));

  END loop;

  END;

  -----------

  I get the error message to create these procedures and if someone help me so I really appreciate it. Thank you

  Concerning

  Shu

  I would just write a single SELECT statement joining EMP and Dept. If this exercise is University (collections of learning PL/SQL types), then you can do something like that.

  I used a PACKET to this implementation. Again, this is not how things are done in the real world.

  SQL > create or replace package coll_pkg
  2 as
  3 type dept_no_tbl is table of the dept.deptno%type;
  4
  5 procedure rec_coll (p_dept_no in dept_no_tbl);
  6 procedure send_coll;
  7 end;
  8.

  Package created.

  SQL > show err
  No errors.

  SQL > create or replace package body coll_pkg
  2 as
  3 procedure rec_coll (p_dept_no in dept_no_tbl)
  4 is
  5. start
  6 because me in 1.p_dept_no.count
  7 loop
  8 d in)
  9 select empno, ename
  10 of PEM
  11 where deptno = p_dept_no (i)
  12                 )
  loop 13
  14 dbms_output.put_line (p_dept_no (i) |) ':' || j.EmpNo | ':' || j.ename);
  15 end loop;
  16 end loop;
  end 17;
  18
  procedure send_coll 19
  20 is
  21 l_dept_no dept_no_tbl: = dept_no_tbl();
  start at 22
  23 deptno select bulk collect into l_dept_no
  24 of the Department;
  25
  26 rec_coll (l_dept_no);
  27 end;
  28 end;
  29.

  Package body created.

  SQL > show err
  No errors.

  SQL > set serveroutput on
  SQL > exec coll_pkg.send_coll
  10:7782:CLARK
  10:7839:KING
  20:7369:SMITH
  20:7566:JONES
  20:7788:SCOTT
  20:7876:ADAMS
  30:7499:ALLEN
  30:7521:WARD
  30:7654:MARTIN
  30:7698:BLAKE
  30:7844:TURNER

  PL/SQL procedure successfully completed.

  SQL >

• Error when switching from WL8.6 to WL10.3

  Hello
  
  I'm trying to improve WL 8.6 to 10.3 WL. When I try to run the Upgrade.sh, immediately, I get the following error
  
  «. "/ upgrade.sh: / opt/app/bea/wls103/user_projects/upgrade_logs/domain_06222010_090215_1: could not create.

  Hi Ben,

  Please try the link below: http://weblogic-wonders.com/weblogic/2010/06/07/oracle-weblogic-10-3-3-zip-installer-for-development/#comment-1028

  .
  .
  Thank you
  Jay SenSharma

• Error of switch device PIN blackBerry Smartphones

  HI - just had to share my 8330 for another.

  I installed costs BB App World, but now when I try to connect and download something, I get the message "do you want to put your device PIN xxxxxxxx.

  I also have our company email enabled so I don't know if the PIN change will affect my work email. I'm not using the desktop software

  Choose Yes or no, and who will cause problems?

  Thank you.

  Yes, you must confirm the change of PIN AppWorld so that your account will be in the right.

  If your (new) device is already activated on your network of BES, then fine. Do the above will not affect your email.

• After I restarted the PC, I get this error "error when switching on: the specified file is not a virtual disk".

  I enclose the list of files in the folder of the virtual machine.

  I have attached the log file.

  I attach the vmx file.

  I don't really know what to do next.

  Thank you for your help.

  Cristian

  Hello Cristian,

  Welcome to the forums.

  Looks like your virtual computer configuration file points to a slice file and not the original vmdk file. You can try to change your vmx file and replace:

  ide0:0. FileName = "E:\VMwareFiles\TR570_IMAGE_BIRT\cloned-000001-s011.vmdk".

  with

  ide0:0. FileName = "E:\VMwareFiles\TR570_IMAGE_BIRT\cloned-000001.vmdk".

  If that does not work, try to re-create the virtual disk damaged by using this thread.

  Good luck.

  Concerning

  Franck

• Error scan with LlaserJet M1212 nf 22

  I'm unable to scan or copy. I was analysis a number of photos with everything works fine until I got the error message scanner error 22 on the printer screen. Even after clearing the error message, I was still unable to scan or copy without getting the same error message. I unplugged the printer and repluged, still the same problem. I uninstalled the printer several times and reinstalled using two installation files found on the part support the HP site, multiple times and still not able to scan or copy. Cannot think of something different to do. Can anyone help with this problem.

  (1) turn off the printer

  (2) unplug the power cable

  3) press the power button on the printer, it will turn on for a second and turn off, it comes to drain the remaining power

  (4) plug the power cable back to the

  (5) turn on the printer

  Scan 6) should now work

  I get this error and switching market just after that 30 seconds won't work, it worked after I followed the steps above, it works for most electronic devices, in case you have a problem, for example my friends HP laptop would not display anything on the screen when turned on, I removed the batteries and you press the power button to drain any power stored in capacitors , then put the battery back and lit it, it worked just fine, same for my smartphone as well when he used to function well.

• blue screen with the error of MEMORY MANAGEMENT. 0x0000001A

  Separated from this thread.

  Hello

  I have a toshiba satellite c870. When I turned on my computer, I got a blue screen by reading the following:

  (blue screen)

  : (

  Your PC has encountered a problem and needs to restart. We are only collecting the error information, and then we'll restart for you. (100% complete)

  If you want more information, you can later search online for this error: MEMORY_MANAGEMENT.

  Then it restarts and I get these 2 following errors of switching back and forth between the two sound tempting to prepare auto repair. See below:

  (blue screen)

  : (

  Your PC has encountered a problem and needs to restart. We will provide for you.

  If you want to learn more, you can search online later to this error: NTFS_FILE_SYSTEM

  Then he goes to the black Toshiba Logo screen as usual and reads the following:

  preparation auto repair...

  And then it goes to another screen blue read the following error message:

  (blue screen)

  : (

  Your PC has encountered a problem and needs to restart. We will provide for you.

  If you want to learn more, you can search online later to this error: FAT_FILE_SYSTEM

  He'll then return to the Logo of Toshiba screen, then the Blue error screen (NTFS_FILE_SYSTEM), then return to the Logo of Toshiba screen and then the Blue error screen (FAT_FILE_SYSTEM). It just keeps it again and again and does nothing else. I removed the battery, removed all caps, deleted all devices USB (mouse) and pressed the power button for 60 seconds. Then I put the battery in place, pluged in the power cord and it turned on. I got the same results, as shown above. NO CHANGE! HELP PLEASE!

  Well Vista and before "XP", usually, do not use the FAT32 file system, they use, as do the new OS NTFS.

  Vista/XP can read FAT32, & can / could use, but its outdated... Memory is not really in this case, but

  you too extended the hardware capabilities of the pc.

  From this point, try to start the BIOS, the value 'advanced settings' once this done, change BIOS for any add-on

  material, save & exit.

• Error of CMF directly after installation "unable to reach the server.

  Hello

  my client has installed the Vmware Image of Firesight management central v6.0.1. After that, I went to the system with https://192.168.45.45. The first message I received from the webfrontend was the message, you can see in the picture I have attached.

  Error of switching field / impossible to reach the server. Reload this page and try again.

  Does anyone know what this means? Is this a problem or a shouldn´t that I care about this?

  Concerning

  Sebastian

  Hello team,

  This clearly indicates the database error unit. The best way to solve the problem is to redeploy (reimage) the device once more so that it will create a new database without any error. Otherwise, you will need to open a request for TAC to truncate the table in the session. The best way that I propose is to redeploy rather than wait for the escalation and continue to repair corrupt database

  Rate and correct mark if the post will help you

  Concerning

  Jetsy

• Problem with switch Cisco SG300

  Hi guys,.

  I have a problem with switch Cisco SG300-20. After the failure of the switch boots in a kind of mode. It requires

  MAC address and serial number to be entered manually for the device. I tried to find information on this mode, but without success.

  My question is: what is this mode and how to make the start switch in this mode?

  How can I turn on the switch in this mode on purpose if it happens again and I enter the wrong information by accident.

  Thank you

  Hi Aegx, this is a rare case where the switch basically forget his identity. Although the switch is recoverable, it is recommended the switch RMA.

  If you are certain that you have neither taken under warranty, all the information that is asked is on the bottom of the switch sticker. If the thumbnail is is not present you wouldn't able to do this is correct.

  In addition, if you make a typographical error, the switch will have undesirable failures that are permanent, such as the inability to update software.

• Background switch detected for MyApp (24) who doesn't have the tunnels open - defocus is NOT called

  I get the error "background switch detected for MyApp (24) who doesn't have the tunnels open - defocus is NOT called. Then the Simulator freezes and I can't do anything. Tried to debug but no luck!

  My application has two other entry points implemented from article http://www.blackberry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800738/800901/How_To _...

  Please see code below

  public class UserInterface extends UiApplication{
  
      public static void main(String[] args){
  
          if ((args != null) && (args.length > 0) && (0==StringUtilities.compareToIgnoreCase(args[0].toString(), "GUI"))){
  
              UserInterface theApp = new UserInterface();
              theApp.enterEventDispatcher();
          }
          else {
              try
              {
                  Wait();
                              SetTimer();
                  ManageResources mg = new ManageResources();
                  System.exit(0);
  
              }
              catch (Exception ex)
              {
                  if (RuntimeConfig.DEBUG)
                  {
                      System.out.println("UserInterface, main:  " + ex);
                  }
              }
          }
      }
      public UserInterface() {
          //  DialogDisplay dd = new DialogDisplay();
          pushScreen(new UserInterfaceScreen(this));
      }
  

  I also had this problem, the cause is that my computer is behind a proxy firewall so that MDS services Simulator cannot connect to internet, I added the following lines in the file rimpublic.property in the directory "Eclipse\plugins\net.rim.eide.componentpack4.7.0_4.7.0.46\components\MDS\config".

  application.handler.http.proxyEnabled = true
  application.handler.http.proxyHost = proxyserver
  application.handler.http.proxyPort = 8080

  These lines must be placed in the [MANAGER HTTP] section.

  It will be useful.

• error after installation of 6 l/r

  error after the installation of the drive.  Unable to create the required folder, error in switching modules

  Windows or Mac?

  If it's Mac, wants to see link below:

  Unable to create the required folder