Error rate scanning for digital USB MCC-7202 / Limitation

Similar Questions

• Keithley UNFINISHED 420 'query' error Max scan for instruments

  Hello!

  We have a system for about 9 years. There is a PC with Windows XP and LabView 6.1. In the PC, there is a card GPIB PCI, and via the GPIB cable, 8 Keithley DVMs (including models like 2010, 2400, 2182) connected. A few days ago this old system began to malfunction. There are 4 screws are parallel on this old system - worked fine until now- but none of them are now able to communicate with the Keithley instruments.

  I got a virus check, also verified WinXP, checking the memory and so on (we had several BSOD also on the old PC). Because I couldn't trace the problem in the old system, I decided to check into the Keithleys with a new configuration.

  I have a new PC with a card GPIB + PCI and LabView 2010. I connected this new PC line above with the Keithley instruments GPIB. (old PC disconnected) When I open MAX and I navigate to the GPIB controller, and I scan for instruments, all DVMs Keithley started a signal sound and displays "error 420" on their screens. And I agree I get in MAX.

  So now I have to think that it is a hardware error? Since I have the same problem of communication the DVMs in this new configuration PC...?

  A defective digital Voltmeter can make unreliable GPIB communication? I have no idea where to go now...

  Moreover, in the case of the controller old PCs, I don't get any visible error, only the screw do not communicate (time error). I think I will also try to use the old system again, I will connect the new PC to GPIB channel and listen in the communication with the GPIB Analyzer functionality.

  Thanks for the tips!

  Basic troubleshooting: have you tried simply as an instrument both for the bus connecting? You can also check the cables.

• Error 85 happening for digital channels 4-digit

  Hello

  I have a labview program that measures the current tension at vs for a field emission device. The problem I'm having is I receive the error message 85 each time my current measurment reached 4 digits, for example, 1000 AU. I read that the 85 error means that analysis of string function is reciving the wrong type of data, so my question is: How can I change the analysis of function of string to accept up to 4 digits? My diagram is attached.

  Thank you

  Thank you.

  I solved the problem today, it turns out that I needed to add a width of string to my duties "decimal channel numbers.

  I appreciate all your help you guys!

• Vista: The device can not start (error Code 10) for a USB CDC device which works fine in XP

  I have a USB device 2.0 DCC which works very well under all of our Windows XP machines, but not based on Vista.  The device uses the usbser.sys driver and emulation of the virtual Comm Port.

  The text of the listing shows the same information on Xp and Vista, except under vista it shows no open pipes.  Shows Device Manager: device can not start (error Code 10).

  Using Vista I can't connect to the vista of CDC through concentrators or device to any other device wireless hub except for a Dlink Wireless hub, which has a layer of software between the CDC device and the PC.  With Xp, it all works very well on more than one PC, with Vista, there are questions.  I use the INF manufacturer provided for Vista, still no results.

  Any ideas on this would be greatly appreciated.

  Hi NuWaveDC,

  Thank you for taking the time to post on the Microsoft answers Forums.

  Please see the following article for an explanation of this error code 10.

  Explanation of error codes generated by Device Manager

  http://support.Microsoft.com/kb/310123

  Follow the steps listed for the error Code 10 see if this helps solve your problem or not.

  Please post back to let us know if this information was useful or not, so that we can help you if need be.

  Robyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error with eStation Zeen - no scan for networks

  I have problems with the Zeen on our station.  We stopped using for a few weeks while moving around our headquarters, and now the Zeen gives the error message "Unable to scan for networks" as soon as I try to turn on the wireless Zeen.

  We also have a new router, so I don't know if they are related.

  I tried a full reset to factory specifications, but as soon as it comes to the installation of the network I get the message "unable to scan for networks."

  My PC is a laptop HP with Windows 7 Home Premium x 64

  Printer is a C510a

  I am trying to connect wireless.  The printer works when it is connected via a usb cable.

  Firmware version is ZEP1CN1130AR (2.2) (113110)

  The blue light on the printer wireless flashes.  However, as soon as I get to the installation of zineb and try to turn on the wireless zineb, I get the same error message.

  I found another thread with this exact error message, with no responses.  I found a bit on connectivity issues of zineb/printer, which I had at some point, but this isn't really the issue here.

  No chance, it's hardware related?  More troubleshooting ideas?

  Thank you!
  Ian

  Everything still works for you?  I hope so!  If the problem does not return, please check accept as Solution to help others with this problem.  If this isn't the case, I can't wait to know if Airprint works even when the Zeen is not.

• USB port from a digital Multiport card will not read the external SSD drive. Right USB - c for the USB adapter works fine.

  USB port from a digital Multiport card will not read the external SSD drive. Right USB - c for the USB adapter works fine.

  It's a new 12 '' MacBook

• Error with Host Update Utility when I scan for patches

  Hello

  I try to use Host Update Utility to update my server ESXi 4.0 to ESXi 4.0 Update 1, but I get the following error when I press the button "Scan For Patches. The error is "an error has occurred. Download failed ". So, I started looking in communities, if someone had the same error and I think that the problem is due to I install my VI Client and Host Update Utility in Windows XP SPANISH version. Could be the language that I use in my OS (Spanish) the cause of this problem?

  I tell you that I do not use any kind of proxies. I am in a private network and between internet and I have only a router. I can navigate anywhere on the internet without any problem and I have no restrictions on what are the ports that I use. The router is reserved for NATS.

  The other issue is . Displaying the HUU configuration file (settings.config) I see the URL for the variable "RemoteDepot" is "https://hostupdate.vmware.com/software/VUM/PRODUCTION/index.xml". "" This URL is correct or VMware has changed it?

  Thanks in advance.

  Warlock.

  I have the same problem. Host Update Utility does not work with windows XP Spanish, you must install Windows Vista Spanish Profesional.

  I think that vmware cares not Spaniards.

• PowerPC error with scan jet 5370c running OS x 10.8 Mt. Lion.

  PowerPC error with scan jet 5370c running OS x 10.8 Mt. Lion. Is there a way to get a driver to work anyway?

  This is to thank you. I think there is a way to continue to use my 5370c. First chance I get, I will work with your suggestion.

  The help page Veuscan confirmed my scanner is included and had good advice. Given my scanner attached USB when I started the software already seems to be the main difference. My first attempt I plugged the scanner after starting the software. I'm testinging the application for free before you buy the full application that might work better. So far, the free app is a little unstable and backward jumps between the default and manual adjustments. The scanner is very slow, an initial overview took 7 min but the scanner works.

• OfficeJet Pro 8710: Scan to a USB key and it continues to implement one. PDF format need VFS - which is not readable - files

  I am using a 8710 Pro Officejet and scanning to a USB device...  However, when it scans to the device, it is shaped in a. VFS which is unreadable files.  How it scan to PDF?

  Hello @jmivanco,

  Thank you for showing your interest in the HP Forums! I see that when you save files to a USB Flash drive, they are saved as. VFS file. I would like to help.

  I provided a post by @Lorem_ipsum that should help: scanned photo to unusable format (*.) VFS).

  I would like to know if these measures worked for you. If they did, it's great! Give us some reinforcements by clicking on the solution and laurels, buttons that help and others see that we have the answers! Good luck!

• OR Max: No button "Scan for instruments.

  Before I start I will say that I used the NI GPIB-USB-HS devices for years with relatively few questions. I also visited several forums posted by people with a similar problem.  Basically, my problem is as the title suggests: when I open OR max and look for the GPIB-USB-HS device there is no button "scan for instruments" I'm used to seeing on the top bar.

  It's the first time I used nor max v. 16.0 and it is quite frustrating.  I believe that my ni488 driver is up to date and I have included all the details of the pilot in the screenshot below.  I can't understand what's not here, but my program LabView can not connect the GPIB instrument.

  A couple more things to note:

  -The same GPIB-USB-HS device that doesn't work here works on another computer with an earlier version of NI Max.

  -LabView program that I use to connect the GPIB instrument which does not work here works on another computer

  -When I browse for the GPIB-USB-HS in 'Device Manager' and select 'set to day pilot' windows tells me that the driver is up-to-date

  -I'm on windows 8
  

  Please help me.

  Hi JohnDoe89,

  This sounds like it would be very frustrating to meet - so let's see if we can reduce what could be the cause of the problem, we can determine the best way to solve it.

  You mentioned that things work correctly on another computer with software versions different-can you let us know which are running the versions of the software on this computer? It would be useful to compare to the list in the picture you posted.

  In the list you posted (I guess it's the software on the computer that does not work, rather than one that is), I noticed that you use 16.0 versions of many of your drivers. The readme for 488,2 drivers, it looks like the version 16.0 is backward compatible with LabVIEW 2013, rather than the 2012 I see on your list. If this computer is running an earlier version of the drivers/MAX, but the same version of LabVIEW, it's perhaps at least a part of what is causing the problem.

  If you can put the list of software for computer work, which will give us more information to work from.

• E/s digital USB-6008 changes when the system starts

  I was intending to use the USB-6008 housing in a critical application in which the digital I/o lines are used to trigger relays.  The relay should activate when I ask them programmatically.  Otherwise, they must remain open.  The problem is that during a reboot of the operating system, the e/s digital USB-6008 go up and down several times - opening and closing my relay.  It is not acceptable for my application.

  Is it possible to prevent the lines to reach logical high except if ordered to do so?

  There is no way to set the startup on the 6008 States.

  As the system USB boot devices and turns on power to the computer and off the power to the USB ports, on the DIO lines go up and down several times.

  You will need to put a logic of material extra, just after data acquisition to ensure that potentially dangerous output combinations cannot affect the relay and the elements they control.

• How to troubleshoot the work of e/s digital USB 6211

  My e/s digital USB 6211 suddenly stopped giving digital output. Board of directors when connected, LED flashes and passes the self-test. But refuses to give any digital output. Can someone help me please?

  Thank you for your time. Technician came and found this Terminal connector was loose. Problem is solved

• Scanning old photos; Scan error try scan from computer or read documentation.

  I have a HP Photosmart printer and scanner and a Packard Bell laptop.

  When I try to scan pictures, I get the message on the printer. Scan error try scan from computer or read documentation.

  I don't know how to scan from computer and lap top does not come with documentation, that everything is on the help screens. I looked and could not find any help for my problem screen.

  I ran the printer troubleshooting, but who has detected no problems.

  Elaine O'Hagan

  Hello

  Looks like you are trying to use the Scan button on the printer, that should work.

  When he says scan of the computer, you open the HP printing software that you have installed since the first installation of the printer, and you use the option/instructions HP Scan from that.

  See you soon.

• 5530 envy: envy 5530 is not scanning for available remote

  REC would help chat of HP who accessed remotely to my system when it wouldn't print now, citing wireless internet connection.  Now it prints wireless just like the printer was new, but I can't scan wireless as I could before.  I must now be attached with USB and the printer display "the computer does not respond. check the USB connection.  the stupidest part of this is that I could always scan with the USB.  I'm lost!  the HP agent removed the original icon of jealousy and it is now replaced with an icon that says "class series 5530 envy."

  Hello @Mommommary and welcome to the Forums of HP, I hope you enjoy your experience!

  I see that you have problems with scanning. I would like to help!

  I would recommend starting with a power reset.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I recommend also to download and run the HP print and Scan doctor.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• No function of scanning for Photosmart C4280 all one after updating to Mac OS x Lion

  I downloaded the update day and new drivers, either, Apple and also the drivers of support.apple.com noted elsewhere in this forum. and the function of the printer worked very well for a usb connection of airport network, but the scan function disappeared. There is no scan.app in the Hewlett-Packard folder and there was before. In theory, the scan function should be networked through the airport like the function of the printer, but I was never able to get there. Now, no function of scanning even with usb directly to the computer. Please, please help. I'm going crazy here.

  Hello

  First of all, the printer connected by USB thrugh airport should provide print you only the functionality, it provides no functionality of scan.

  As you can find below, only print sharing feature described by specification from Apple:

  http://www.Apple.com/airportexpress/features/printing.html

  Then, while the printer directly connected by USB, you should be able browse Iamge Capture.

  There should not be any folder Hewlett-Packard, the scan functionality provided through Capture of Image as a complete software not available for operating system features.

  Please follow one of the options below to find how to scan using Lion:

  http://support.HP.com/us-en/document/c01910186

  If you are not yet able to scan, install the latest drivers for printer HP package and try to scan the image:

  http://support.Apple.com/downloads/DL907/en_US/HewlettPackardPrinterDrivers.dmg

  Please let me know of any questions,

  Shlomi