Error refreshing MV on Cube witQuery re - write enable

Similar Questions

• Error-200524 occurred at .vi:2 DAQmx Write (analog 1-d NChan DBL 1Samp)

  I'm trying to generate a signal to usb-6009 of simulated signal.

  However, he keep poping errors:

  Error-200524 occurred at .vi:2 DAQmx Write (analog 1-d NChan DBL 1Samp) if I choose "1 sample on request" in mx data acquisition.

  If I have chaged to "continuous sample", the error has become

  Error-200077 during the property Node DAQmx Timing (arg) 1 DAQmx Timing (sample clock) .vi:3-> 1.vi:Instance:0:1-> Untitled 1 Untitled. VI

  Can someone could take care of my problem?

  Very appreciate

  The limitations of the analog output of your device is documented in the manual and has been considered on several occasions. Because it supports at the time of the application, you can only pass a single value to a moment, not a waveform. The timing is only the software and you can not generate a signal without a lot of jitter and the max frequency will be by the spec.

• Error message on Windows XP, "Windows-Delayed Write failed, windows was unable to save all the data for the file.

  I use windows xp as the operating system. I bought the new 3G huawei data card. While surfing internet, between a pop-up is displayed

  «Windows-delayed write failed, windows was unable to save all data in the file C:\Documents and settings\new\Local Settings\Application Data\Google\Chrome\User Data\Default\Session Storage\004285.log.» The data has been lost. This error can be caused by a failure of your computer hardware.

  After this computer freezes and I have to restart my computer. Please help me how to fix this problem.

  The error basically says that he tried to write something on your hard drive and for some reason that unfinished write operation.  This could indicate a bad sector on your hard disk, damaged disk or a problem with your hardware.

  Whenever a problem involving a disk read or write appears, my first approach is to perform a verify operation of the disc to the hard drive.  Even if this is not your problem, it is a step of good routine maintenance. Run the disk check with the "/ R" or "Repair" option.  Note that the real disk check will be presented at the next reboot, will run until Windows loads completely, cannot be interrupted and can take more than a few hours to run depending on the size of your hard drive, the quantity and type found corruption and other factors.   It is better to perform during the night or when you won't need your computer for several hours.

  'How to perform disk in Windows XP error Cherking'

  <>http://support.Microsoft.com/kb/315265/en-us >

  HTH,

  JW

• When you try to share my internet connection via AD HOC I get this error: "an error occurred while internet connection sharing was being enabled. the dependency service or group was able to start. »

  original title: cannot share internet

  I shared my internet via ad-hoc, using my wifi in my laptop running vista 64-bit. It just stoped working and now I get a message saying

  "an error occurred while internet connection sharing was being enabled.   the dependency service or group was able to start. »

  Hello

  You can view the article in the Microsoft Knowledge base and check if it helps.

  Error message when you try to connect to an ad-hoc connection in Windows Vista or Windows 7: "Windows cannot connect to" " "»

  http://support.Microsoft.com/kb/946481

  Let us know if you need more assistance.

• Compression filter incompatible error-1074396007 took place at IMAQ AVI write Frame

  OK, so I have two computers.
  On one of them, the VI works fine, on the other hand, I get an error and no AVI file.

  I'm taking a bunch of tif files and compression of AVI file with Compression Indeo® video 5.10 filter.
  Two computers running Windows XP.  He who works is more older and slower (but still quite new, 2 years old).  The news that does not work is a dual core with 3 GB of RAM.
  One difference is that with the old computer Labview is installed on the C drive with windows.  On the new computer Labview is installed on a second partition (drive D) while windows is installed on drive C.

  Initially the demo write avi file and compare the VI compression filters would not work on the new computer, but after upgrading Direct X version 9 and restart the computer, they work now.  With the compare compression VI IndeoR 5.10 Compression filter filter example video works fine.

  When I try to start my VI (joint) on the new computer it works, but I get an error (error-1074396007 is produced through the filter of compression IMAQ AVI write Incompatible framework.) Possible reasons: IMAQ Vision: Incompatible compression filter (Hex 0xBFF60499).) and no avi file is produced.  When I run other filters with the VI, I get an avi file which works fine!

  I have NEITHER Vision 8.2.1 installed on both computers.  On the old computer, I also have older versions of Labview installed.

  I even is gone to the windows/system32 and found the CODEC (ir50_32.dll) on the old computer and copied and replaced the version I had on the new computer.  This had no effect.

  A reflection as to why I get this error?
  André

  Adding a strip of 2 worked, so I guess that the div by 4 the rule applies.  Thank you.
  André

• Error refreshing MV...

  Hi all
  
  I am trying to refresh a MV using the below cmd... I get this error? I have treid with sys, with the user... same thing... also treid... begin and end cluase... same error... the MV was create with this cluasse "REFRESH COMPLETE ON-DEMAND... masse which play a role in this update?
  
  SQL > EXECUTE DBMS_MVIEW. Refresh (User.TEST_MV);
  DBMS_MVIEW BEGIN. Refresh (User.TEST_MV); END;
  
  *
  ERROR on line 1:
  ORA-06550: line 1, column 35:
  PLS-00357: Table, view or reference sequence "User.TEST_MV" not allowed to
  this context
  ORA-06550: line 1, column 7:
  PL/SQL: Statement ignored

  Refresh on demand is exacly what. This means that there is no automatism because the update for you. You have to do - and you did a syntax error. It works as stated above.

  You also have other options to refresh:

  (1) with a calendar that you provide with him create materialized view stmt
  (2) on commit - also specified with the mv to create

  Then you wouldn't have to exec dbms_mview.refresh manually (on demand)

  Published by: Uwe Hesse on May 13, 2009 10:11

• I use Encore CS6. When I try to burn a BluRay disc I get the error: "" code: 3, create sequence stc cannot write file M2S "." This error is only when in the project are more then a (menu or chapter or timeline)

  How can I fix this error?

  This error is probably from multiple sources and it has no uniform solution reported. It can be drive or media. It can be permissions. A reinstall of the still has set at least a situation. Reduce the size of the bitrate/project can avoid the error. Make sure that you still run 'as administrator'.

  (If you get this when you try to burn a disc, test the workflow to the point of actually burning a disc by one) construction of an image and b) burning with another software like ImgBurn to Toast for Mac or PC.

• Error satellite A40-SP151 - compatibility of the writer DL, DVD - RW - ide #1

  Hello
  Can anyone add to the list of * of compatible DVD burners for Satellite A40-SP151 *.
  Googling readers listed previously, they seemed to be just DVD-ROM/CD-RW combo.
  Download
  Toshiba G8CC0000R810
  Hitachi G8CC00015810
  TEAC G8CC0001D810
  HITACHI G8CC0001K810
  Panasonic G8CC0001C810
  Toshiba SDR2412OAA

  I'm trying to upgrade to a DL, DVD - RW disc.

  I can confirm KD08 Pioneer and Panasonic UJ - 850 FWv1.10 are _not_ compatible, this last, I can't find any firmware for (trying to swap master / slave settings)... (Don't want to mess with the pioneer)

  I think the Ref. TOSHIBA DVD-RW/CD-RW COMBO SD-R6112 is compatible, if anyone can confirm this?

  Any help would be greatly appreciated.

  Thank you

  Hello

  I think that all of the list found in the manual of use of Satellite A40-SP151.
  In my (not for the A40) user manual I could find compatible ratings

  Greetings

• Cannot remove the Photos from an SD card in the card reader in Windows 7 error "is an error error application attributes - produced - the media is write protected."

  Please check the post from Jetta48 on this article, for the workaround to resolve your concern.

  Have a nice day ahead!

  I agree with you and think it had something to do with a Windows Update. I got this computer with Windows 7 for a couple of years and it took until this month I got the problem. Cannot delete the photos when the card reader is on a Windows 10 computer either.

• Display the event log: event ID: 32, the driver has detected that this \device\Harddisk1\DR3 there cache write-enabled

  I recently discovered this error in my view the event log, do not know how to locate which disc it means or how to disable the setting cache: it's the XML view details screen.

  -

  -

    <>disc"/ >"

    32

    3

    0

    0 x 80000000000000

    <>2010-08 - 25 T 04: 28:36.363Z"/ >"

    85397

    System

    Stu - PC

   

   

  -

    \Device\Harddisk1\DR3

    0F00100001000000000000002000048001000000100000C00000000000000000000000000000000000000000000000000000000000000000

   

   

  I hope someone can help me with this work out I seem to have nothing else than problems at the minute...

  Thank you

  Download http://www.nirsoft.net/utils/shexview.html
  Disable all non-microsoft shell extensions (to explore) and reactivate a
  by so this can help.
   
  The filmThe Explorer accidents - in the control panel select Problem Reports and
  Solutions (Type wercon.exe in new task), go to historical problem, right-click
  your mistake and choose check for the Solution. You can also examine the details
  and AFTER the exact text of the ERROR here (that can pinpoint the source of)
  the error). .
   
  You can clean boot
  Troubleshooting http://support.microsoft.com/kb/331796
   
  Windows files for curruption click Start - all programs-
  Accessories - right on command prompt and choose Run as administrator.
  Type Cmd in the new task. Then type
   
  sfc/scannow
   
   
   
  --
  ..
  --
  "stusalford" wrote in message news: d85b4087-413f-4a7f-840 d-6b9c3ee73f0e...
  > I have recently discovered this error in my view the event log, do not know how
  > to find out who he average disk or how to disable caching: this is the
  > View of XML on the details screen.
  >
  >
  > -
  > -
  >
  > 32
  > 3
  > 0
  > 0 x 80000000000000
  >
  > 85397
  > System
  > Stu-PC
  >
  >
  > -
  > \Device\Harddisk1\DR3
  >
  > 0F00100001000000000000002000048001000000100000C00000000000000000000000000000000000000000000000000000000000000000
  >
  >
  >
  >
  >
  >
  > Hope someone can help me with this work out I seem to have nothing
  > but issues at the minute...
  >
  >
  > Thank you
  >
  >
  >
   
   

• AppPortal error: remote access to the server is not enabled

  I'm lost on this one.

  Using the full client of AppPortal on a Win7 64 bit machine (version 8.0 of the customer)

  Double-click the icon, download authenticated - published applications show, then double click a published application, the end user receives:

  Remote access to the server is not enabled.

  This happens only on a single computer

  From this profile of users on the given computer I can MSTSC on the same server without problem

  The error also follows the profiles on the given computer.

  I have closed the Antivirus and Windows Firewall and still can not get this to work.

  Even uninstalled and reinstalled the client.

  From my computer, I can easily log in as this user.

  Customers get automatically configured through an XML file.

  After installation, I tested this laptop and he always gave the same error.

  I ended up him to give me the phone for a few hours.

  Uninstalled the version that was there (build 8.0.0.forget) and scoured the Windows Explorer for all left overs (a little here and there in user profiles and delete).

  Then scoured the registry for expressions; vWorkspace, Quest Software and Provision Networks and remove all instances

  Reinstalled all THE SUCCESS with the new connector to our servers (8.0.306.1427)

  Thanks for the help Dave

• has received the error ORA-44416: invalid ACL, while trying to enable network services

  Hi guys I got the ERROR ORA-44416 after the activation of services network in 11 GR 2 to send emails, so I ran this command found just as shown below in the Oracle document library

  SELECT THE ACL, PRINCIPAL

  OF NACL, XDS_ACE ACE DBA_NETWORK_ACLS

  WHERE HOST = ' *' AND LOWER_PORT IS NULL AND UPPER_PORT IS NULL AND

  NACL. ACLID = ACE. ACLID AND

  ARE NOT (SELECT NULL FROM ALL_USERS WHERE USERNAME = MAIN);

  That returned a result of

  no selected line

  What could this mean

  The installation is done on a localhost and the APEX version is 4.2.2 browser is mozilla fire fox

  ORA-44416 means that the ACL that you tried to create to refer to a valid principle - that is, the user does not exist.

  The SQL code that you included above seems to be looking for associated ACL principles which are more database users. I don't see a direct link between this request and the ORA-44416.

  What was your original script of ACL?

  Also, because it is a question of database rather APEX you might get a better answer on the forums of the database.

• Error in the page when the ADF security enabled

  Hello
  
  I created an example page JSF with only a text to output "Hello World!"
  
  When I run the page without activating the safety of the ADF, it works fine.
  
  I activated the ADF security according to the "Enabling Oracle ADF security 29.3" in Guide of Dev for the ADF.
  Now when I run the page, it shows the default login page. I enter username and password and 'send '.
  
  After that, it shows an error with the following error page:
  --------------------------------------------------------------------------
  Error 500 - Internal server error
  java.lang.RuntimeException: cannot find FacesContext
  at javax.faces.webapp.UIComponentClassicTagBase.getFacesContext(UIComponentClassicTagBase.java:1855)
  at javax.faces.webapp.UIComponentClassicTagBase.setJspId(UIComponentClassicTagBase.java:1672)
  at jsp_servlet.__testpage1_jspx._jspService(__testpage1_jspx.java:85)
  at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
  to weblogic.servlet.internal.StubSecurityHelper$ ServletServiceAction.run (StubSecurityHelper.java:227)
  at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
  at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292)
  at weblogic.servlet.internal.ServletStubImpl.onAddToMapException(ServletStubImpl.java:408)
  at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:318)
  at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
  at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
  at oracle.dms.wls.DMSServletFilter.doFilter(DMSServletFilter.java:202)
  at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
  at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)
  at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
  to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.run (WebAppServletContext.java:3588)
  at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
  at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
  at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2200)
  at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2106)
  at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1428)
  at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
  at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
  ------------------------------------------------------------------------------------------------------
  
  Any suggestion/help in this regard is appreciated.
  Thank you

  Hi vbokar! ;)

  I check your application and I noticed that the political ADF seems be grayed in JDev so I re - run the Configuration Wizard for the ADF security.
  Other changes were:
  

• user "vbokar" was added to the application role 'testRole1 '.
  <>changed the password of the user vbokar for "password1" (so I can test it)
  
• changed the home page or from the success_url of ' / TestPage2.jspx ' to ' / faces/TesPage2.jspx.

  Run and Viola! It works!
  Here is the updated file...
  https://docs.Google.com/leaf?ID=0b-coz_ZFqg5XMmQyNGZiNTAtY2YwZC00YWMwLWIxNWItM2ExZWVlOTFjN2Ri&hl=en

  Kind regards

  Pino

  PS. as I also proposed Vikram wire, please build > CleanAll your app. Or better yet, remove it and load the one you sent me.

• Impossible to download World of Warcraft, receive the error message "DEP (Data Execution Prevention) should be enabled for this program.

  original title: need help, DEP is upward :(

  Here's the deal, im trying to download World of Warcraft. DEP (Data Execution Prevention) don't. When im trying to change it and add it to the list "settings for DEP" it won't let add me. DEP (Data Execution Prevention) should be enabled for this program. You can not disable DEP (Data Execution Prevention) for this program. -so here's the question, what can I do to fix this? I rebooted my pc as an hour ago, b4, I did I actually got the game installed. Is there a way for me to squeeze the game spent DEP (Data Execution Prevention)? Please help me with this. Thank you. -Mikkel.

  Hello

  EricLaw IEInternals - a peek at Internet Explorer from inside. -Understanding DEP/NX
  http://blogs.msdn.com/ieinternals/archive/2009/10/10/understanding-data-execution-prevention-crashes-in-IE8.aspx

  The problem might actually be an addon or another program causing the problem and you
  must verify that 1.

  What antivirus/antispyware/security products do you have on the machine? Be one you have
  EVER had on this machine, including those you have uninstalled (they leave leftovers behind which)
  may cause strange problems).

  Start - all programs - Accessores - system tools - IE with no Addons - does this work better?

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security - reset all Zones by default level - apply / OK

  not better?

  Close IE and try again IE or IE with no Addons

  IE - tools - manage Addons (for sure disable SSV2 if she's here, is no longer necessary, but)
  Java always install it and it causes problems - you never update Java to go back in and turn it off again.)
  Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look
  right. Allowed are usually OK and "unauthorized" are not always bad. If a doubt
  program to ask about it here.

  Could be a free - BHOremover - BHO - standalone program, needs no installation, download and
  run - not all are bad but some can cause your question. (Toolbars are BHO)
  http://securityxploded.com/bhoremover.php

  Startup programs (Vista)
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  How to change, add or remove startup programs in Windows 7
  http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

  Also get Malwarebytes - free - use as scanner only. If you ever think malware and which would be
  stands with Prevx running except for a cookie of occasional low level (not a big deal), the update
  and then execute it as a scanner.

  http://www.Malwarebytes.org/

  I would add prevx so.

  Prevx - home - free small, fast, exceptional protection CLOUD, working with other security
  programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here
  or use Google to see how to remove.
  http://www.prevx.com/

  PCmag - Prevx - Editor's choice
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  -------------------------------------------------------------------

  Do yourself a big favor and work through 1 above.

  Data execution prevention Internet Explorer Windows 7 included - several difficulty methods here
  http://HubPages.com/hub/data-execution-prevention-Internet-Explorer

  Feature Data Execution Prevention, or DEP in Windows Vista & Windows 7 - see also the links to the
  at the bottom of this page.
  http://www.WinVistaClub.com/F33.html

  How control DEP but I don't recommend turning it off and certainly not to let power off.

  How to enable DEP on or off for a program of Vista (and Windows 7)
  http://www.Vistax64.com/tutorials/65790-DEP-turn-off-programs.html

  How to enable or disable DEP in Vista (and Windows 7)
  http://www.Vistax64.com/tutorials/120778-DEP-enable-disable.html

  ====================================

  If nothing else works you can try this however I would use as a last resort.

  IE - Tools - Options - Advanced Options - Internet Security Section - clear the check box enable memory
  Protection to mitigate the attacks online - APPLY - OK close and restart IE

  I hope this helps.

• Refresh cube error

  I got below error while doing the refresh of the cube. Dimension update went well.
  
  < ERROR
  TEXT = "ORA-33272: analytic workspace TEST_AW." Cannot open TEST_AW.
  ORA-33275: application of an analytic workspace update autonomous transaction is not supported
  "/ >".
  
  OLAP version: 11.2.0.1

  I was able to reproduce this GLOBAL standard schema.

  DECLARE
    jobid VARCHAR2(100);
  BEGIN
    SELECT DBMS_SCHEDULER.GENERATE_JOB_NAME('JOB$_') INTO jobid FROM DUAL;
    DBMS_SCHEDULER.CREATE_JOB(
      jobid, 'plsql_block',
      'begin
        dbms_cube.build(
         ''units_cube, price_cost_cube'',
         atomic_refresh=>true,
         parallelism=>0);
       end;',
    0, null, null, null, 'DEFAULT_JOB_CLASS', true, true, 'CUBE Job');
  END;
  /
  

  The build failed with the following error.

  JOB$_544
  FAILED
  37162: ORA-37162: OLAP error
  ORA-33272: Analytic workspace GLOBAL.GLOBAL cannot be opened.
  ORA-33275: Autonomous transaction query of an UPDATEd analytic workspace is not
  supported
  ORA-06512: at "SYS.DBMS_CUBE", line 234
  ORA-06512: at "SYS.DBMS_CUBE", line 287
  ORA-06512: at line 2
  

  The following combination seems to be necessary to hit this bug.

  (1) you run the generation through Task Scheduler;
  (2) you specify atomic_refresh-online true OR there's MVs cube defined;
  (3) you specify parallelism-online 0

  Technically the build code runs an SQL statement on a view of dimension after an UPDATE, but before POSTING. (This is a consequence of atomic_refresh to-online true + parallelism-0 online). I do not understand why it works in the main session, but not when the lanyard of the Task Scheduler. I will file a bug on this, but in the meantime I suggest you specify parallelism = 1 or atomic_refresh => set to false.