Display the event log: event ID: 32, the driver has detected that this \device\Harddisk1\DR3 there cache write-enabled

Similar Questions

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

  I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

  Hello

  Check the drive for errors and see if it works fine it after.
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  The link above includes steps for the same.
   $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• Error installing Microsoft NET Framework 3.5 Service Pack 1 Setup program has detected that this computer does not meet the requirements to install this software

  I need to install Microsoft NET Framework 3.5 Service Pack 1, as it is necessary to perform a Dell diagnostic Test, but I've been advised that: Setup has detected that this computer does not meet the requirements to install this software. Requirement: Windows install 3.1.

  However, when I look at the download page of Windows Installer 3.1 is not actually as for XP with SP3. I tried anyway and: Setup has determined that the version of Service Pack for this system is newer than the update you are applying. There is no need to install this update. Well actually it is there...

  Is there a way to get around this?

  See below articles for solution

  1 system requirements for the .net framework

  http://msdn.Microsoft.com/library/8z6watww.aspx

  2 download links for .net framework

  http://www.Microsoft.com/net/download

  or

  http://msdn.Microsoft.com/en-us/library/5a4x27ek

  3. top 8 resources for .net framework

  http://www.Microsoft.com/net/itprofessionals

  4 dependencies and Versions of .NET framework

  http://msdn.Microsoft.com/library/bb822049.aspx

  5 frequently asked questions
  http://msdn2.Microsoft.com/en-us/netframework/aa497323.aspx

  6. management of versions, compatibility and run side-by-side in the .NET Framework
  http://msdn2.Microsoft.com/en-us/netframework/aa497340.aspx

  Good luck

• I get a message saying that the installation has detected that a reboot of the machine may be pending and recommend I have quit the installer and restart my machine.  I did 4 times and tried to install again and again but keep the same message.  Guilty pl

  I get a message saying that the installation has detected that a reboot of the machine may be pending and recommend I have quit the installer and restart my machine.  I did 4 times and tried to install again and again but keep the same message.  Help, please!

  

  Hi Keleahaiko,

  Please click on IGNORE and continue with the installation, let us know if this helps.

• The driver has detected an error of the Comptroller on \Device\Ide\IdePort3

  Hello

  I'll try to explain my problem as best as possible in chronological order then please bear with me.

  I have Windows 7 x 64.
  So last week my PC have been freezing every two days. Sometimes every day. Black screen during the games, navigation or doing any activity. Each window has frozen, the screen went black. ctrl alt del did not work no response to any entry, the only option was to restart.

  Once restarted, the system would freeze again almost immediately, and again after another reboot. Only solution was physically turn off the computer, turn off the power and wait.  After some time (5-10 min) I turn the power on and system worked very well.

  I went to the observer of events and found "the pilot detected an error of the Comptroller on \Device\Ide\IdePort3." It took place in a series starting with a per minute, then after a few minutes, two or three that occur within one minute, the frequency of this error would be gradually go back even to 10 per minute and that's where the system would freeze.

  Looking at the event viewer I thought, hold for a second I have 3 discs (Disk0 - new SSD, Disk1 - new HDD, Disk2 - old HDD) so maybe that ideport3 refers to the CDROM which I disconnected but the error has not disappeared.

  Check the BIOS settings and deleted everything that had no boot from the internal storage (so: floppy USB - disk, CDROM,)-which did not help either.

  In the Act of desperation, I unplugged my old disk (Disk2) for 6 days I have not known of IdePort3 errors and system will work very well.

  After 6 days, to my embarrassment, error returned.
  This is the story of the appearance of the error:

  10/05/2015 19:56 - after that, I unplugged old hdd
  16/05/2015-09:35
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:35
  16/05/2015 14:36
  16/05/2015 14:36
  16/05/2015 14:37
  16/05/2015 14:37
  16/05/2015 14:37
  16/05/2015-17:28
  16/05/2015-17:29
  16/05/2015-17:31
  16/05/2015-17:33
  16/05/2015-17:33
  16/05/2015-17:34
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:37 - after this system error stopped

  Here are the details of the error

  -
  -
   
    11
    2
    0
    0 x 80000000000000
   
    107016
    System
    Odin
   
   
  -
    \Device\Ide\IdePort3
    0000100001000000000000000B0004C004000000850100C00000000000000000000000000000000001000000000000000000000005100000
   
   
   
   
  Let me know if you all the news and thank you for your time in reading my number.

  I bought the card mother-GA-Z68X-UD3-B3 3 years ago. There can be no IDE ports. It has 6 SATA ports.

  Here an explanation somewhat losely formulated to work on the port that could be the culprit. Since you have 6 SATA ports, why not play the game of elimination with them?

• NVIDIA GeForce 8400M GT: the driver is installed for this device is not compatible with Windows 7 (from Vista 32-bit)

  Hi all, I am interested in my Sony Vaio AR41L (under Vista 32 bit SP2) upgrade to Windows 7, but when I run the Windows 7 Upgrade Advisor, it tells me that, for the graphics card, NVIDIA GeForce 8400 M GT, the driver "installed for this device is not compatible with Windows 7.

  Apparently, NVIDIA is not a solution and sent people to Sony, and Sony say that they have not updated the drivers for Windows 7 and that we do not know when they expect to do...

  All known and solved this problem?  Any suggestions would be very helpful!

  Thanks in advance.

  someone noted that nVidia will come out a new batch of pilots in the coming days. (once a month)

  It may be desirable to wait outside and continue with VGA Standard at the moment. Help others, tell us which solves your problem. Click useful Vote for those who help.

• Windows Media Player cannot play the protected file. The player has detected that the connection to your hardware might not be sure

  I just bought the New Avengers movie with the digital copy. I moved it and now I can't watch it. I have "Windows Media Player cannot play the protected file. Drive detected that the connection to your hardware may not be safe. "when I click it. What now?

  Hi Jason,

  Thanks for asking this question to Microsoft Community.  I'll try and help you resolve the problem; However, I will need to ask you a few questions.

  Are you able to play other movies without any problem? Have you done a recent software or changes to the material on the computer?

  Here is a link with some good steps. Go through it and check if it helps. Also check out this article and see if it helps.

  Also, see the steps in the article and see if it helps.

  Hope this helps and let us know if you need more assistance. We will be happy to help you.

• Event ID 11: the driver has detected an error in the controller on \Device\Harddisk2\DR11.

  My event log is loaded with these on a system just to receive Dell 15-Sep and I don't know why.

  Do not ask questions - yet.

  I would like to know how to solve this, please. Thank you!

  Hello

  Have you connected external hard drive to the computer?

  In almost all cases, these messages are due to hardware problems. The source can be the controller or (more probably) a (drive 2) device that is connected to the controller. The problem of equipment may be termination rate settings, bad wiring or incorrect transfer, a defective unit, or in rare cases, a bad device driver written.

  Run the troubleshooter.

  Troubleshooting Windows

  http://Windows.Microsoft.com/en-us/Windows7/troubleshooting-in-Windows

  You can also check this thread:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Windows-7-64bit-USB-problem/b9eb5cfe-0036-45ef-b7f0-36c973398f49

  As it is a new computer, I suggest you contact the manufacturer of the computer.

• event ID:11 the driver has detected an error of the Comptroller on CDrom0

  Hi all

  DVD drive does not read or write

  the operating system is windows xp sp2.

  I checked for the hardware changes in Device Manager there is no...

  It was working fine a few days ago, but now it is not

  so I checked where the spectator, I had the id of the error above.

  Kindly help

  I don't know I'm missing something... kindly help

  Concerning

  Sudeep

  Hello

  • What were the changes made before the issue started?

  I suggest you to refer to this link:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

• I have a windows xp OEM SOFTWARE license key, but the drive has failed. This key will work on any XP installation disc?

  due to a major problem, I have to completely remove the operating system (under license). can I still use this key to set up windows again? I have a key to the back of my sticker only computer laptop written "SOFTWARE OEM windows xp". Can I use this key with any windows xp cd? or I have to use a specific version? can u give me the link to download the specific version?

  Thanks in advance

  You must use the recovery disks provided by the manufacturer (or the integrated recovery system) - see you manual for more details.

  The major advantage of this is that all the required drivers should be included, so that you can immediately connect to the internet and install all updates.

  Reisntalling using the sysstem of correct recovery also means that you shouldn't need to use the key on your COA stiker - as key to 'master' of the manufactuerer is integrated into the system and should not require activation.

• My laptop says that the system has detected that a cooling fan does not work correctly

  My laptop cooling fan stop working

  If you haven't cleaned your laptop since you bought it, it can y dust/dirt clogged in fans, then he must have stopped working.

  OR

  In case if you overloaded some cell days with intensive, ongoing use of heavy tasks running.

  Check if you have disabled the fan of the BIOS settings.
  To access the BIOS settings, press ESC when the laptop starts.

  Also apply thermal paste and carefully clean the motherboard of the laptop, entered air, etc.

• My Muse site will not display the customized html images that work in chrome?

  My Muse site will not display the customized html images that work in chrome? Here's my url www.simplesites.com.au.

  Works fine here on Linux.

  Note that the uploads has 'ads' in name and come from simplesites.net.au, so be sure that content blockers not get triggered.

  • http://www.simplesites.com.au/Web-support-and-maintenance.html
  • http://simplesites.NET.au/wp-content/uploads/2013/05/contact.PNG
  • http://simplesites.NET.au/wp-content/uploads/2013/05/quote-left-01.PNG
  • http://simplesites.NET.au/wp-content/uploads/2013/05/right-quote-01.PNG

• gauge the battery to the boot screen and battery on report menu conflicting Details about the level of the battery. The gauge from the battery to the Starter incorrectly displays the low battery level that prevent the macbook pro battery retina start

  gauge the battery to the boot screen and battery on report menu conflicting Details about the level of the battery. The gauge from the battery to the Starter incorrectly displays the low battery level that prevent the start of the battery. This happens on macbook pro retina 13 inches

  When I try to startup macbook pro retina in battery mode, it will fail to start showing low battery level and an indicator to recharge the battery. It does not start on battery. When I then connect via the power cable at startup (and check the battery level), monitor of battery in the menu bar indicates that the battery is charged to the top.

  It gets really frustrating and remove my ability to use the macbook pro retina as a truly portable device...

  Appreciate any help on this

  Have you tried resetting the SMC? Reset the management system (SCM) controller on your Mac - Apple Support