Error starting IdeaPad Z510

Similar Questions

• Battery IdeaPad Z510 problem

  Hello everyone,

  Last week, I installed 10 64-bit Windows on my laptop (Ideapad z510).

  The first time my laptop is suddenly turned off, but the battery was far from empty according to windows. When I tried to start again it appeared that the battery was empty.

  I noticed that the percentage that windows reports is incorrect. After 2 hours without power my battery was normally about 30%. Now, it was still above 90%.

  I have installed power manager and I use the balanced profile.

  Does anyone have an idea what could be the problem?

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• How to install W8 in Mode for Lenovo Ideapad Z510 UEFI?

  Hello world

  I've been struggling with the w8 installation on my laptop Ideapad z510 in UEFI mode, but not I could succeed it or me I found something that might help. I will explain clearly the case.

  Point 1:
  As I understand it, for successful installation in UEFI format w8, we need choose the mode of 'First UEFI"from the Boot Menu in the BIOS. Then, the source of the shoe must be specified to identify the rigid path to documents to be loaded so that the new OS could be installed correctly.

  Pharmacodependance1:
  It is possible to choose UEFI boot mode first, but it is not possible to choose the USB for UEFI boot path in this case, which does not allow to succeed a UEFI boot to your computer. You cannot reach the DVD or USB, the installation files are, and start the installation process.

  Point2:

  If we consider the first case, you must choose the Legacy Support of your computer startup mode and achieve the USB or DVD drive to install the new operating system on the computer.

  Problem2:
  To succeed the UEFI mode when the computer starts, you should see 4 different partitions on your drive to the point of disc selection, if you choose the disk you install your operating system. However, when you select the Legacy Support in BIOS mode, the disk partition is limited to 2 in my case, that are:

  • Main drive
  • Reserved system (350 MB)

  That is why, when I continue the installation, the OS is installed on the traditional way. After installation, when I go into the BIOS to choose the UEFI boot mode for mode, the laptop checks some network connections and said

  • EFI network failure 0 for IPv4
  • EFI network failure 0 for IPv6

  respectively.

  So, advice, aid, ideas and suggestions are gladly welcome to overcome this problem. Could you please help me?

  PS: Please don't say that "you can't install because your computer does not support", because I have received computer technical service and a W8 version has been installed in UEFI mode. However, I deleted to install W8 pro.

  Greetings,

  Okan

  First of all, your bootable USB key must be created in the UEFI. Just google and you will find solutions.

  You can install W8 mode UEFI. Just allow to boot from USB in BIOS, select Exit Saving changes and restart.

  I think it's your basic problem. Let me know if you have already done this and still having the problem.

• [SOLVED] Energy Win8.1 (Ideapad Z510) Manager

  Hello

  I am a new user of Lenovo (Ideapad Z510) with Win 8.1 and I have problems with a feature in Energy Manager (installed original Lenovo disk).

  In the settings menu, there is a function "zoom to screen." By using this feature, you should be able to enlarge and reduce the size of menus and icons using Fn + and Fn - buttons. I tried it and all my menus have become bigger, and I can't go back... Whenever I have press Fn - it just sort of plant. A few pictures to see the problem:

  (Sorry, that the menu is in Hungarian)

  (1) some features

  Link to photo

  (2) after pressing Fn - icon Manager duplicates the energy and all the bar becomes strange

  

  (3) all menus (right-click right, or even at the office) became huge

  Link to photo

  Thanks in advance for any help!

  Note of the moderator; image (s) converted into programming on display images in Forums

  Oh, it seems that it is now resolved. If, instead of using the cursor (it has been on the smallest) I went from police in the menu below from 11 to 10, and now it seems fine. I tried to solve the problem with the cursor before, but have not thought to decrease the font size.

  Thank you for the help, Jonas!

• How to invert the fn keys in ideapad z510

  Hello

  I recently bought a lenovo ideapad z510 and I have to press fn in order to use the f1 - f12 keys. Is there a way to change this trend so that I don't need to press fn to use the f1 to f12 keys?

  Hi moving.

  Welcome to the Community Forums of Lenovo!

  Can you try to go to BIOS by pressing F2 when you power on the system

  Once inside the BIOS look for an option that says mode HOTKEY or hotkey, should be under the configuration tab.

  change this option and must reverse the use of the FN on your system.

  (Remember to press F10 once your done to save the changes you made.

  

  If the hot key mode is not available in BIOS, you may have to wait or consult on the download site of the Lenovo Support for BIOS updates

  Hope this helps

  See you soon!

• Error starting compile step: make sure that a compatible version of Xilinx tools is installed in the location specified in the Setup from LabVIEW FPGA.

  Please help me for this problem "error starting compile step: make sure that a compatible version of Xilinx tools is installed in the location specified in the setup of LabVIEW FPGA.»

  Look for the error on the Web site of or or on the forums. Take a look at the following links:

  http://forums.NI.com/NI/board/message?board.ID=170&message.ID=381394&requireLogin=false

  http://forums.NI.com/NI/board/message?board.ID=170&message.ID=205754&requireLogin=false

• My computer guard turn off at startup; error starting Windows. Could someone help me please?

  Hello

  I have an Emachine, which is about three years old. We take good care of it, look at what we download and perform analyses of virus frequently a week. But for the last two or three weeks every time we start our computer, it takes a few times before he can actually get into Windows because it maintains power off. When he died, and we turn it back on, the computer goes to the screen if you want to put it in safe mode or start Windows normally, because there was an error starting. The computer offers the possibility to try and correct the error, but sometimes it is remedial and it still happens or it goes into repair mode and powers off the coast.

  We downloaded and installed the System Mechanic (the latest version), hoping that it could detect errors in the disk hard because we heard good things about the program. Unforunately after installation and with us the program running, he finds errors in all of the computer, but after you power on your computer and leave it alone for a few hours and turn on again, the problem comes back right to the top. From a logical point of view, we think it could be either an error on the HDD causing constantly turning the computer off, there might be a virus in the Startup Repair which is not find and fix the problem or there might be something wrong with the power supply by to short circuit and power off.

  Nine times out of ten once the computer is turned on, you can even say that there is a problem to be with, because everything works well. We have some important information about the computer is harmful that we can find and fix the problem.

  Thanks a lot for your time!

  Cory

  Hello

  ·          When the issue started?

  Step 1: Disconnect any external devices and try to start the computer.

  Step 2: Check if the computer starts in safe mode.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  See also: http://windows.microsoft.com/en-US/windows-vista/What-to-do-if-Windows-wont-start-correctly

• Error starting 3

  original title: error starting

  My computer just started this doing. any ideas on how to solve this problem?  with 3 error loading key

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Error starting "appName": Module "appName" is trying to access a secure API

  Dear all,

  I downloaded a few applications in the app world. When I try to install on the device, there is an error "error starting Sunfish6: Module 'Sunfish6' trying to access a secure API. I tried to update the files, he needs, but still get the same error message. What is the cause of the appearance of the error message? I developed this application using phonegap and blackberry webwork framework.

  Thanks & best regards.

  In the eclipse webworks menu, select project-> BlackBerry-> sign with Signature tool.

  Then upload the generated files.

• Error starting FreeLoader: Module 'KxmlLib' not found.

  The message "Error Starting FreeLoader: Module"KxmlLib"not found." what do I get when I try to run my application on a BB device.  In the Simulator, it does very well.    KxmlLib is a library to the library (preverified) BlackBerry project kXML 2 . The KxmlLib project is a project of the library without the source, just the pre-audit jar files and in the KxmlLib properties > Java Build Path > libraries a pre-audit jar and Properties KxmlLib > Java Build Path > order and export has the JAR checked for export.  I guess it's okay.

  After that it got a little hairy, I had to the the KxmlLib of the project a dependency of my application of FreeLoader project, run it on the simular to produce the KxmlLib JAR in the deliverables of the project KxmlLIB directory.  I removed the dependency of the project KxmlLib , copied from the KxmlLib.jar in the project space of the FreeLoader , right click on it project and added to the build path.

  Applications of freeLoader compiles and runs without any error of security on the Simulator.  When I try to package and run it on the device of BB, it fails.   Clues?  I browsed this forum before I asked - I solved all my other problems during development with the help of this community and the RIM fanastic.  Thank you very much!

  Brandon

  You will find that there is a cod associated with your pot of KxmlLib.  There is no end to your device unless you deliberately include in your distribution.  You may be signed too.

• Using new plugin error: error starting module. Of verification errors.

  I use eclipse Galileo and the latest version of the plugin.

  I created a project, and I was able to debug it about 50 or so times. After that, I can't run the project on the Simulator again. He complains saying this:

  Starting MiApp
  Module 'MiApp' has verification errors.Error starting MiApp: Module 'MiApp' has verification errors.
  

  These errors do not appear before, and I have not changed anything. Attempted to restart eclipse, own Simulator, recompile, but nothing works.

  MiApp is a UiApplication who uses a library module. The library is located in the debug settings.

  I have read the famous document on how to avoid mistakes review and none of the points worked. In fact, my application is not a MIDlet.

  I spent several hours (which I would have spent on development) without success, and I'm going back to the old plugin. This new one really sucks.

  I'm sorry it's late for that. He took 20 minutes to move the project to the old plugin environment, but invested much more although the two hours I spent playing with the new plugin and the search for the light in this forum and knowledge base.

  Now it works perfect, as expected.

  The old platform (eclipse 3.4 and plugin 1.0.0.67) is much more stable and easy to use.

• Error starting MyApplication

  Hello

  Because I developed application on the Simulator and it worked fine.

  Now, I downloaded the application for device via OTA and tried to run the application but I have error like below.

  ------------------

  Error starting Module MyApplication 'MyApplication' tries to access a secure API.

  ------------------

  Should that code signing? or another problem?

  Thank you

  DK.

  Yes.  Your application requires code signing.

  See the Javadoc for the API you are using.  It will include the following message from the not-so-friendly:

  Category: Signed: This item is only available to signed clients. If you intend to use this item, please contact RIM to establish the necessary agreements that will allow you to have your signed COD files. Signature is required for use on the device, as part of the JDE development may occur without signing the Cod.

• [FIXED] WL library error start error: Windows Live Photo Gallery encountered an error and cannot start. Error code: 0 x 80070035

  Original title: error starting in WL photo library

  Hello guys,.

  I use the photo gallery of WL (latest version) for some time, but one day it stopped working without remembering any important changes that might break a.

  When I try to run it, it gives this error:

  ---------------------------
  Windows Live Photo Gallery
  ---------------------------
  Windows Live Photo Gallery encountered an error and cannot start.

  Error code: 0 x 80070035
  ---------------------------
  Ok
  ---------------------------

  I tried to reinstall it but without success. I've also renamed the files Pictures.pdX C:\Users\\AppData\Local\Microsoft\Windows Live Photo Gallery, but with the same result.

  Not to mention that the event log does not contain messages recorded on this subject and also the follow-up of the process with Process Monitor did not show anything that would tell me the cause of this problem...

  If someone from the Live team or an MVP watch that I can send you the output monitor process or any other information that you might find useful.

  Any other suggestions on what I can try next?

  Thank you!

  Chris

  I'm waiting for the confirmation of the guys from the Live team on this, but I've corrected this problem.

  The error came from the fact that Windows registry stalled Chronogram of some access roads network I had on my computer from a former WHS (Windows Home Server) box so basically, Windows Explorer - WL photo library was still trying reach these network paths, even if in Explorer / settings there is no references to WHS, so registry entries in neutral paths and wrong...

  Replace the data of those key in the Windows registry under the HKEY CURRENT USER corrected this problem and I was able to start WL photo library.

  :)

• Crystal - «Error starting PeopleTools» report error

  Working in PeopleTools 8.52.22 with Crystal Reports 2008 (12.3.0.601)

  Not really experienced with Crystal.

  Creates a new query and report based on a... Crystal report work and the query can be connected without problem

  Added a process and attached to the component that is similar to the original of the report

  Everything seems the same, but when I run the report, the newspaper simply indicates "error start PeopleTools".

  Have tried many things... to restart the AppServer and ProcessScheduler too.

  At loss on what to do to allow this to run properly.

  I found my problem... in the drop-down list parameter... I had inadvertently 'Ignore' and that caused my problem.

  Thank you

• MacBook Pro running Mavericks: error starting Pro first

  I have a Macbook Pro 2011. I have Premiere Pro CS5, CS6 and now CC 2015. CS6 has worked for a long time, then came all of a sudden with this error:

  "Adobe Premiere Pro can't find capable video game modules. Please update your video display drivers and start over. »

  So I reinstalled CS5 of the thought of disk, it might be useful. I have CS5 on the Macbook, and it works fine. I can't figure out how to get CS6 once again, even though I have the serial number for it. I installed CC 2015 but it comes up with the same error for CS6 start-up.

  I went into System Preferences and made graphics of course automatic switching is turned off, rebooted, and it always comes up with the same error starting. What can I do to run the CC 2015? I'm fine with moving permanently to CC 2015 so I can't get CS6 once again, but I had rather not step back with CS5 if I can understand this problem

  Any advice will help. Thank you!

  First of all, can help http://www.adobe.com/downloads/other-downloads.html

  Second, the Mac utility for adapters double http://forums.adobe.com/thread/1017891?tstart=0