Error starting system (my system boot is mistake...).

Similar Questions

• Error starting system Acer Iconia W500

  Hello friends

  I have a problem, I updated my W500 with Windows 8 and Windows Update did not work after looking on the web for some answers that I found that I had to mark the C: partition as "active", I did it, but now I'm on a black screen that reads:

  Windows could not start a recent hardware or software... etc
  File: / Boot/BCD
  Status: 0xc000000f
  The startup of your Pc Data configuration is missing or contains errors

  Now, I try to start on the Bios to reinstall the system (I installed Windows 8 by making a bootable usb key) but I can't get into the bios, it goes directly to the black error screen, I also tried to use a cd/dvd external drive, but it has a 2 usb cable is not powered externally so I don't know if this can be done with a device like this

  What can I do? Please I need some advice to solve this problem, to be able to enter the bios, restart something, use something specific, just what I may need to do

  Thank you very much for your time

  Will be

  I solved the problem... could not get into the bios menu, so I flashed an old bios on the Tablet (with a USB bootable USB with bios on this topic file) using a manual procedure of service I found on the web... the tablet should be activated, using the Windows key + Volume DOWN + Power... this procedure Flash the bios into the motherboard After that I could use the F2 function and enter the bios and reinstall Windows with a bootable USB key...

• Whenever I boot Windows XP Professional I get the message: error 7026 system event log

  Original title: 7026 event log system error

  Get an error in the error 7026 system event log the following boot-stat or system-stat driver could not load DCDisk.  I get this log entry each I boot XP Pro.  It doesn't seem to be the cause of failure, other than the log entry.  The only app that has a dcdisk.exe I can find is Farstone I installed on the system

  Uninstall and reinstall the program that you have installed that has created the entry

  http://consolecopyworld.com/DC/dc_utils.shtml

  Alternatively, you can remove the redundant entry using Autoruns.

  To identify what loads when you start using Autoruns (freeware from Microsoft).

  http://www.Microsoft.com/technet/sysinternals/ProcessesAndThreads/Autoruns.mspx

  With Autoruns, you can deselect an item which disables startup, or you can click with the right button on an item, then remove it. If you clear the check box that you can check back for re - activate the element. It is an approach much safer than editing the registry and better than using msconfig.

  Another useful feature of the program is that you can click with the right button on an item and select search online to get information about the selected item.

• "80070002" error the system cannot find the file specified with start.vbs

  Original title: Windows Script Host

  Script: C:\Program Files\PCDApp\start.vbs

  Line: 2

  Char: 1

  Error: The system cannot find the specified file.

  Code: 80070002

  Source: (null)

  1 first, update your AV program and run a full scan. Then download, install, update and run a full scan with malwarebytes(free). This will help you establish that his little likely to be malware related, or not.

  If each scan find and remove whatever it is, does the problem persists after that scans have completed?

  2 if so, try a clean boot. If the problem does not occur in 'clean boot' then follow the section "How to determine what is causing the problem by performing a clean boot" in an attempt to establish that generated the message.

  Do not leave your PC like the clean boot and return to a normal startup after your investigations.

  3. If the boot doesn't help, take a look at autoruns to see if that can locate which is turned on and generates the message.

• I have an error msg "Unable to connect to the firewall local host control" is displayed when the system boots

  OS - win7 family Basic 64-bit

  anti virus-macfee
   
  Original title: I have an error msg "Unable to connect to the firewall local host control" is displayed when the system boots. MacAfee antivirus, 1 GB Radeon graphic

  McAfee has been updated at the same time as the last batch of updates from Windows 7 and it seems to be the cause of this problem for most, if not all, users.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I got McAfee, but the connection has started working again on its own so I thought I was clear of problems. However, when I checked it says he was doing routine checks the updates in vain when I told it to do a manually. So stick with McAfee you don't follow their procedure of fix would have upgraded my PC at risk by not updated and, like other McAfee ads have since explained, the application did not refer to its database of threats correctly [and this could explain part of the variability of the symptoms of failure but all involved loss of internet connection]. Actually, I removed McAfee then installed Microsoft Security Essentials rather & my answer IE is faster I knew it [even though I had the Add-ons McAfee disabled for centuries].

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  You probably should have updated to 10.5.8 first.

  Installation or update of Snow Leopard:

  http://manuals.info.Apple.com/en_US/Snow_Leopard_Installation_Instructions.PDF

• When you try to install Windows Defender I get an error message "Service"Windows Defender"(WINDEFEND) could start. Make sure you have sufficient privileges to start system services.

  Original title: could not start the Service "Windows Defender" (WINDEFEND)

  When you try to install Windows Defender, I get an error message that

  "Service"Windows Defender"(WINDEFEND) was able to start. Make sure you have sufficient privileges to start system services.

  How can I check which privileges I have and I need?

  I noticed in the management of the tasks that Norton symlcsvc.exe ran and I was wondering if it was who collide with the Defender, so I temporarily stopped Symantec process running in the field of Services, but still had the same result, try to run the installation of the Defender.

  Help please

  Hello

  This error message is because you have Norton installed on the computer. See the for more information section below.
  http://www.Symantec.com/business/support/index?page=content&ID=TECH103119&locale=en_US

  Let's try the steps and check them off below if it helps.

  Step 1: You can try to uninstall Norton and then check if the problem persists.
  Note: Reinstall Norton after verification.
  Reference: http://support.microsoft.com/kb/307895

  Step 2: Change the registry value and check.

  a. Click Start, type regedit.exe and press ENTER.
  b. navigate to the following location: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows Defender\
  c. right-click on DisableAntiSpyware, on the right panel, then selectEdit.
  d. enter 0, under value data, and click on the OK button.
  e. close the registry editor.
  f. restart the computer.

  Registry warning:
  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• What is causing the error event ' BCM42RLY service failed to start due to the following error: the system cannot find the file specified "Event Id 7000

  What is causing the error event ' BCM42RLY service failed to start due to the following error: the system cannot find the file specified "Event Id 7000

  Hello

  1. Since when are you facing this problem?

  2. What is the number of brand and model of the computer?

  3. have you made changes on the computer recently?

  BCM42RLY is a Broadcom network card driver. I suggest that you uninstall and reinstall the drivers and check if it helps.
  Uninstall or reinstall a device: http://technet.microsoft.com/en-us/library/cc725782.aspx

  Hope the information is useful.

• Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

  This seems to have started with the last batch of updates of Windows 7 (including SP1).
  I can't connect using dial-up.  Get the message:
  Cannot load the Remote Access Connection Manager service
  Error 711: The operation could not complete because it could not start the remote access connection manager service
  in time.  Please try the operation again.

  When I try to start the Remote Access Connection Manager service manually, I get the message:
  Windows could not start the service on Local computer remote access connection manager.
  20 error: the system cannot find the specified device.

  My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

  I don't know what else might have changed.

  Hello Vince_867,

  Thanks for your post.  Take a look at this thread for a possible solution to your problem.

  See you soon

• Windows Live ID Sign in French Wizard error - "Windows Live ID Sign in Assistant (wlidsvc) Service could not be started. Make sure you have sufficient privileges to start system services. "

  I want to install the Windows Live Id sign in assistant.

  But when its almost done I get this message:

  "Windows Live ID Sign in Assistant (wlidsvc) service could not be started. Make sure you have sufficient privileges to start system services. "and the RETRY and CANCEL buttons.

  Can someone please tell me what to do.

  I appriciate it :)

  Hello

  For more specialist help on issue of Windows Live Sign-in Assistant, you can post your request here:

  Windows Live Forum - http://windowslivehelp.com/

• Read error - SOLUTION system configuration data

  Today, I found a solution to the error of notorious boot not only on the toshiba, but some other brands also.

  The error is: System configuration data read error.
  He invites to start with 2 beeps which prevents the computer laptop Moldavian from.

  I tried everything I could to remve this message but noything helped me.
  Replace all, cmos battery, updated the bios, loader, drives, keyboard and etc.

  Today, I found a solution very simple that I want to share with you guys.
  This solution worked for me and I hope it will work for you too.

  Are you ready? :)

  Go to the Bios and change the Bios language french.

  Post here if it works for you also.

  Thanks for sharing your experience with us. But its really hard to believe that your solution would be linked to all devices such problem

  However, good to know that this small change in the BIOS has helped you to resolve the issue

• XP - error: the system cannot find the specified file.

  I was installing Windows XP Service Pack 3 today and it worked very well until he came to update registry after the installation process, after what is happening the installation closes and then displays an error "the system cannot find the file specified." I tried to close all programs, and then restart and shut down everything that runs when the computer starts and which also failed.

  Hello
   
  
  1. have you downloaded the stand-alone package for the service Pack 3 or are you using Windows update?
  2. are you able to boot to the desktop now?
  
  Method 1.
  Run Disk Cleanup and disable the security software and t hen try the same installation and check.
  Want to t he article below for disk cleanup:
  http://support.Microsoft.com/kb/310312
  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  Method 2.
  If the problem still exists together own starting the computer and attempt to install the service pack.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353
  Note: After that troubleshooting is complete, configure the computer to a normal startup. See the "steps to configure Windows to use a Normal startup state" section in the article above.
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows XP SP3: Unable to start, System Restore cannot drag and drop ALL the files/folders on the desktop and applications, many unable to start, services cannot search, cannot copy or transfer the any files folders...

  After a recent power outage, my system has restarted with a weird and very common Windows problems range. The system boots fine, all my personal files/folders/apps are intact, have suddenly stopped almost all functions of applications, but many crucial functions of the Windows kernel. Everything seems to point to several Windows Services are unable to start (administrative tools on the start menu). I am running Win XP SP3 and that he was going to upgrade to Windows 7, but I wanted to backup everything in advance. As I have 29 000 hours on my C: drive and a lot of time invested in my system, files, and applications, I am extremely reluctant to risk losing my files and applications by performing any type of reinstalling Windows. Strangely, begin to almost all my apps and all my files are accessible for the most part, but I've lost the ability to drag and drop files, folders or items in a list within the applications COMPLETELY. I can't copy or paste anything, can't move the desktop icons (although I can create new files and folders). So at the moment I can't save anything or even a single file transfer to a hard drive on another storage medium. Immediate reaction: try safe mode and try the system restore safe mode has the same problems (likely due to the large number of system services that inexplicably refuses to start) and the system restore says an error window saying "system restore is not able to protect your computer at this time. try restoring the system running and restart again", which of course NEVER changes. It's the equivalent of getting a tire on your car in the middle of nowhere to find the spare tire flat and the missing Jack. I have used to be fanatical about the definition of the regular restore points, but now can not access them. I have backups of most of my personal files, but over years have lost most of the original installation CD for many of my applications (there are over 100 applications on my system) and I don't want to lose the file associations and architecture of directory tree that it took my so long to implement. I started with Win XP media center edition of first (circa 2004 or almost) and have migrated twice more of 3 hard disks and 2 computers. All this time (5 years of daily use), I have NEVER known so many malfunctions for as many Windows basic and vital functions at the same time. I tried a lot of 3rd party "windows fix - it / registry repair" apps, all have no effect. Everything I can speculate is there was some serious damage to the registry and have no idea how/why so many Services refuse to start. In MMC, more than half of the services actually start and run, the rest all give the error message "the service or dependencies is not start (error 1068).» In addition, very oddly, no. APPS or windows appear in the toolbar AT ALL, but the Quick Launch toolbar works very well, just like the tray button and start tasks (?! )!). If I reduce a window, it "disappears" (Nothing on the task bar), but I can restore it using the alt - tab keyboard shortcut to switch apps, so all applications/windows appear on the list of the Task Manager. A few apps is paralyzed bad, as the player windows media, itunes, etc. (I guess because the service windows audio can not not start), some won't start at all, but 90% of them work fine, except to try to copy or back up all files. I can create new files, however. I'm desperate to find a solution to repair XP3 Win WITHOUT losing my installed applications and files, before I try and switch to WIndows 7. Any help/suggestions/links/advice would be much appreciated. I'm an experienced user, but I've never met so many malfunctions based on the OS at a time. I, however, very painfully learned (years before that my system so complex) it's been almost a re-installation of Windows guarantees to lose my installed apps and files, the directory tree architecture associations.

  Help, please!

  I'll be honest with you - your message is so difficult to read that I don't bother to go through all that. Next time consider using white space, ball or points numbered, etc. to make your message more readable. I stopped reading after your first sentence and only scanned the rest quickly. I do not mean to hurt your feelings; just trying to help you get targeted answers you need for the future.

  The blackout has corrupted your Windows installation. Back up your data now. Since you have problems so much, it would be probably best is to remove the hard drive, put it in a USB drive enclosure and attach it to another computer to copy the data OR start the target with Linux Livecd such as Knoppix system and copy the data to an external hard drive. IOW, do not use the damaged windows to try to get your data.

  You can try a repair that will leave your programs and facility data intact, but with this widespread bribery, it is unlikely to work. However, it takes only a few minutes and is so worth a try. If the repair facility does not work there is nothing to do, but a clean install. And Yes, it will mean that over again.

  Consider buying a UPS to help prevent future damage by power outages. For a single computer, you should look for one in the area of $60 to 80. A more expensive UPS is not necessary. Another good disaster recovery strategy is to buy an external hard drive and Acronis True Image. You can image your system (and can make an incremental backup image so that your image is still current). You can apply your image and be back running that you were in relatively few minutes after a hard drive or Windows to fail.

  http://www.michaelstevenstech.com/XPrepairinstall.htm - repair install how-to
  http://michaelstevenstech.com/cleanxpinstall.html - Clean install - how-to
  http://www.elephantboycomputers.com/page2.html#Reinstalling_Windows - you will need at hand MS - MVP - Elephant Boy computers - Don ' t Panic!

• Cannot install on XP Pro SP3: "Service Pack 3 Setup error - the system cannot find the file specified."

  I am trying to install SP3 on my XP Pro.  I get a notice on my screen, stating: "Service Pack 3 Setup error - the system cannot find the file specified."  Don't know what I'd do.  Thank you.  Peter glass

  That's good news. I think you also need to analyze of rootkits being on the right side. So, now:

  Search for rootkits with a program SPECIALLY designed to detect and remove the (aswMBR):

  http://public.avast.com/~Gmerek/aswMBR.htm

  Download this file to your desktop. Double-click the icon to run the program. When the opportunity to download and install the latest Avast definitions do.

  Run a scan. Results in red indicate that this was not a false positive! Do you need to remove the rootkit (including "FixMBR" if necessary).

  And finally, leave your PC on overnight and search for viruses, using this site:
  http://www.eset.com/us/online-scanner/
  Once we are convinced that your PC is clean, here are my instructions (just in case where you still cannot run batch of Geek-Tech file, etc.):

  1. download the installation of SP3 and IE8 (beforehand) files. I prefer to keep these (and other useful files) on a USB key, but this is optional. Here are the links for the installation files:

  http://www.Microsoft.com/download/en/details.aspx?ID=24 (for SP3)

  (You can TOTALLY ignore the message "intended for it professionals"!)

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=43 (for IE8)

  (You need to install IE8 AFTER SP3! Trust in me.)

  IMPORTANT NOTE!

  It is VERY important to ensure that Internet Explorer is at the level IE6 before installing SP3. In case you have IE7 or IE8, you must uninstall it / them, using the Control Panel Add / Remove programs. Let us know if you need assistance with this.

  Once again:

  Make sure that IE is IE6 level before installing SP3. You can go directly from IE6 to IE8 after SP3 has been installed.

  2. disconnect Internet. Also unplug all unnecessary devices.

  3. temporarily disable the automatic updates. To do this:

  Start | Control Panel (switch to Classic view if not already selected). Automatic updates

  4 set up a clean boot. The last thing you need is for a program that runs in the background to interfere with these updates! (It happens!) For more information:

  http://support.Microsoft.com/kb/310353

  (Note that this is the same as setting up a "Diagnostic boot.")

  Reset.

  5 install the SP3. Restart TWICE.

  6 switch to IE8. Restart TWICE.

  (What happens very often is that someone has their software antivirus running as they try to install SP3, which often translates into chaos! "This is why it must be done after installing SP3 and IE).

  7 unscrew the clean boot. (That is, return to the Normal startup).

  8 make sure that firewall Windows is activated (it should already be):

  Start | Control Panel | Security Center

  9 visit Windows Update to download and install only the critical security updates. Restart each time you are prompted.

  10 re - enable automatic updates.

• Error: The system does not license for the OS image. The system cannot find the path specified

  Hello

  I copied the image of Windows Embedded 7 T510 using HP thin client capture on a USB port. Now, I'm trying to load this image in an another thin client Embedded Win 7 T510 via a USB port.

  However, when the customer starts using this image of the USB, I get error below.

  "Error: the system does not license for the OS image! The system does not have the specified path.

  What solutions do you recommend.

  Thanks in advance

  Solution:

  I tried to install it on a Linux Thin client... Is there had this error.