Error to Start Task.vi DAQmx 200120

Similar Questions

• Daq stop task VI back to the State of the task was really forward the DAQmx Start Task or DAQmx writing?

  Hello

  I use DAQmx and DAQ Assistant and try to get the details on the following questions.

  1 does Daq stop task VI really return to the State of the task is in front the DAQmx Start Task or DAQmx writing? Digital Input taking as an example, I don't think that the status of the task means that input data because I tried and I can't really back to the entry level it was.

  Maybe more experienced people can help to share their expertise.

  2. the information in help indicates "virtual channels created with the function/VI DAQmx create Virtual Channel are called virtual channels the and cannot be used in the task." But I don't know what "in his work" means.

  3. could I get some guidelines or expertise on the Labview programmers when use virtual channels the and when, to the more global?

  Thank you!

  Best regards

  Allen

  If you create a channel of the task, or scale just usuing the screw to create or Assistant session wire io is the only way to pass the info autour.  It is not saved anywhere on the disc.  A channel of the task or the scale in a project can be used by anything in this project.  A channel of the task or the scale recorded in MAX can be used by anything on this machine.  Its an extended thing.

  And Yes, the DAQ Assistant fresh extra performance overhead and the poor than the DAQmx API.  Often, it won't have the impact of a little experiment.  Large applications should avoid the express Visa.

• Error 200428 creating task in DAQmx Base

  I wrote a basic program that captures a voltage signal, plots and written to a file, but when I run it, I get this error message:

  "Error-200428 occurred at the value passed to the control task/channels is not valid."

  I enclose a copy of my VI. At first, I do not have the VI 'DAQmx Base create a task' in the block diagram, and I was getting the above error. After a search through some documents, it seems that the problem was that I had to put the VI to "Create a task" in when you use DAQmx Base. Unfortunately when I did, I kept getting the same error.

  Y at - it something I'm doing wrong here?

  Here is my software/hardware information:

  Operating system: Mac OS X 10.11.14

  Material: NEITHER myDAQ

  Software: LabVIEW 15.0 (64-bit)

  Drivers: DAQmx Base 15 OR 15.5, 15.5 OR-488 VISA. 2 NOR-DAQmx for myDAQ on Mac OS X (all for OS X)

  AliMoradi wrote:

  I wrote a basic program that captures a voltage signal, plots and written to a file, but when I run it, I get this error message:

  "Error-200428 occurred at the value passed to the control task/channels is not valid."

  Here is my software/hardware information:

  Operating system: Mac OS X 10.11.14

  Material: NEITHER myDAQ

  Software: LabVIEW 15.0 (64-bit)

  Drivers: DAQmx Base 15 OR 15.5, 15.5 OR-488 VISA. 2 NOR-DAQmx for myDAQ on Mac OS X (all for OS X)

  Hi Ali.

  You encounter this error, because NEITHER-DAQmx Base does not support unit OR-myDAQ . You have NEITHER-DAQmx for myDAQ installed, however, that supports this feature.

  See the instructions here to confirm that the device and the pilot communicate properly:

  Get started with NOR-DAQmx for myDAQ on Mac OS X

  http://www.NI.com/Tutorial/52345/en/

• Error-229771 to Start Task.vi DAQmx

  I get this error as described in: http://digital.ni.com/public.nsf/allkb/03123D0E8A36C48E862577A4005B6BAA?OpenDocument I tried the solutions suggested, nothing works. Using Labview 64 bit (latest versions)

  Is there a particular reason that you use LabVIEW 64-bit? I would like to try with the 32-bit version. I also suggest that try you without the DAQ Assistant.

• Error-50103 occurred at DAQmx start Task.vi:11

  Hello

  I use a nor-6008 to perform a thermal sector and I get the error "error-50103 occurred at DAQmx Start Task.vi:11 '. I have read other forums of discussion and it seems combe because I use the wizard DAQmx who don't properly resolve the resource when finsihed. I've dug further and saw that it is linked to an on-board clock synchronization problems. However, I can understand how to solve this problem.

  I thought that I create a loop that continuously monitors inputs and sometimes to interrogate the memory so I'm not kidding to the top of the clock. It's much harder to do than sounds. Can someone take a look at my code and give me some advice/suggestions to clean the DAQmx assistants.

  Thanks in advance

  Cole

  I finished by dividing my resource between the two input channels using a single assistant DAQ and dividing down the data rate and the number of samples. Works fine now.

  Big pain in the ass well.

• Error-200022 occurred at DAQmx start Task.vi

  Hello

  I have peripheral cDAQ and 3 modules that nor-9234 connected.

  My program (see attachment) works correctly with only 2 modules, but does not work with 3 modules.

  With 3 modules I have this error: "error-200022 occurred at Task.vi DAQmx Start.»   "Possible reasons: resource requested by this task has already been reserved by another task."

  To solve this problem, please help me

  Thank you

  Now I understant the error. This is correct (see below)

  

• Do you need 'DAQmx start task' vi read from a device NI DAQ (NI 9205)?

  I have a NI 9205, which I use to get a waveform data. To get started quickly, I used the wizard DAQ Vi. The code below (FIGURE 1) is the acquisition of data help VI looked like when I convert LabVIEW code and made some minor adjustments.

  When I looked online to see how to get hardware DAQ data, many sources use the task start DAQmx in figure 2.

  DAQmx start using VI makes another?  Materials using DAQ assist in loop gives you a lack of performance?    If so, figure a will have a lack of performance too as it is basically the DAQ help code?

  FIGURE 1

  Hello sticyfinger,

  Help for the Start Task function:

  "If you do not use this VI, a measurement task starts automatically when execution of the reading DAQmx VI. Automatic start of theDAQmx VI entry write determines if a build task starts automatically when the execution of the writing DAQmx VI.

  If you do not use the DAQmx start task VI and VI task DAQmx stop when you use DAQmx Read VI or VI to write DAQmx several times, as in a loop, the task starts and stops several times. Start and stop a task repeatedly reduce the performance of the application. »

  Hope that helps!

• Error message: "the Task Scheduler service does not appear to start" when you back up files.

  Original title: error in Vista Task Scheduler

  Hello. I am running Vista Home Basic. I'm trying to back up my files, but get an error stating that "the Task Scheduler service seems not be started. Please start the Task Scheduler service and try again. "I don't know what that means and I couldn't save my files before. Do you know how I can fix this problem? Thank you

  Hi MK_806,

  You can try to scan the file system [SFC] checker on the computer that will replace missing or corrupt files & check if the problem persists.

  For more information, you can consult the following link.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Check if there is information in Event Viewer which may help us to solve the problem:

  What are the information contained in the logs of the event (Event Viewer)?

  For more information, you can also consult the following article:

  Troubleshooting Task Scheduler

  Hope this information is useful.

• Error-200609 occurred in the DAQmx write: selected buffer too small

  Hello, I write a few VI simple test that I will build finally to call external analogue output VI. I started with a very simple program to produce samples finished using the clock on board with DAQmx Timing.VI. When I run the program, I almost immediately get an error. The error message is below.

  Error-200609 occurred at writing DAQmx (Analog DBL 1Chan 1Samp) .vi:1

  Possible reasons:

  Generation cannot be started because the size of the selected buffer is too small.

  Increase the size of the buffer.

  Contradictory property
  Property: Output.BufSize
  Corresponding value: 1
  Minimum supported value: 2

  Task name: _unnamedTask<1C>

  I used the VI DAQmx before in similar applications and never encountered this error. In addition, I read the link below which DAQmx Timing.VI should automatically generate the buffer. Any ideas what could be the cause?

  Data sheet:

  Windows 7

  LabVIEW 2012

  PCIe-6353 as DAQ card

  Here is a picture of my diagram and the VI is attached.

  Oops. Just realized my very stupid mistake: I forgot to add the VI of task start. I did and it works as expected.

• CDAQ start task required?

  In an application using the cdaq 9172 and HAVE, I have a Subvi Setup that configures synchronization then starts the job in time loop do some daq display and the Scriptures. I just noticed that the beginning task.vi DAQmx Start is not mandatory. It seems that the Read DAQmx works whatever the weather I start the task or not. Is that correct. Do not use the start DAQmx task.vi?

  Very often, read the help... really helps:

  State transitions to start the measure or the generation to run the task . With the help of this VI is necessary for certain applications and is optional for others.

  If you do not use this VI, a measurement task starts automatically when the Reading DAQmx VI runs. The Autostart of the VI DAQmx writing input determines if a build task starts automatically when the writing DAQmx VI runs.

  If you use not the DAQmx start VI task and the task to stop DAQmx VI when you use DAQmx Read VI or VI to write DAQmx several times, as in a loop, the task starts and stops several times. Start and stop a task repeatedly reduce the performance of the application.

  -using the LV

  Christian

• Task Scheduler error-' the selected task "{0}" no longer exist. " To see the current list, click on refresh. »

  Once I made a few changes in Task Scheduler. After rebooting my system, I found that explorer.exe starts not and task scheduler does not run. So I did system restore. After that things seems to work very well. But when I started the Task Scheduler. It gives following error.
  "The selected task"{0}"no longer exist." To see the current list, click on refresh. »
  Task status: data read failed
  Active the task: cannot read data
  It seems that it is impossible to read any coz task defined window, it shows no defined task window. When I explore the folder in the list of directories of Task Scheduler it shows that no task instead gives the same error.
  "The selected task"{0}"no longer exist." To see the current list, click on refresh. »
  When I click on "Create basic task" of the Action it gives the following error
  "The Task Scheduler service is not available or the folder does not exist. "Verify that the service is running and what folder.

  Hello

  The following items have the steps to fix the respective errors:
  Error code 412
  Error code 413
   

• C000021a error: {fatal system error} when starting laptop PC M30 series

  I get the following error when starting my laptop.

  "Stop: c00021a {fatal system error} the windows logon system process ended unexpectedly with status 0 x 00000080 (0x00000000 0x00000000).
  The system was stopped.

  I have the CD of restoration at the time of purchase. I have some data I need to recover. If someone knows the resolution of this problem, please let me know the procedure.

  Thanking you in advance.
  -YG

  Hello

  I found an interesting page. Please check all the solutions mentioned on this page. http://www.eggheadcafe.com/NG/Microsoft.public.WindowsXP.accessibility/post652591.asp

  Good luck!

• Error on starting the PC

  Hello
  I get the following error when starting my PC. I only started getting this error since I upgraded my anti virus software. I installed all available updates and nothing seems to work.  I restarted the PC several times and have tried help and support but keeps it in the message that appears.
  Can someone help me on this?
  Thanks in advance

  WINDOWS DEFENDER
  «Failed to initialize: 0x800106ba.» A problem caused this program blocking. to start the service, restart your computer or search help and Support to find out how to start a service manually.

  Hi AdianoCreano,

  Please use the Forum of the community for Vista.

  What is your current antivirus?

  I wonder if she does not understand an antimalware tool. If so, there is the question. You cannot, or at least should not be two anti-malware programs that are running.

  If it's not her, please let us know.

  Matt
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• error: "error cannot start fron CD-error 5."

  Original title: cannot restart from a cd

  Hello

  I'm trying to restart xp so that I can use a Norton recovery CD. However rebooting and pressing the prioritization boot from the windows cd comes up with "error cannot start fron CD-error 5."

  Any ideas?

  Thank you

  The disk you are trying to boot from was not burned correctly. You will not be able to boot from it.

• I was doing a winpeshl.exe.error when starting "the application was not properly initialze (0xc0000006). "Click to complete the application.

  I was doing a winpeshl.exe.error when starting "the application was not properly initialze (0xc0000006). "Click to complete the application" when I click ok it reboots. I can even recover the system, tried F8 startup, alt/F10, F2, launch repair system, Safe Mode and all the rest and still get the same error. System specs are Acer Aspire 5920, Intel T5450 processor, 2 GB ram, 160 GB of HDD, windows vista edition Home premium.  I am currently under the memory diagnostic tool windows, but it is said that the test results will be displayed again once you log in, but I can't log in to view them.  The test seems to be hanging around 21% so I don't know how well it will do

  Hi A1W1LL,

  A clean boot helps eliminate software conflicts.  Let us check if software is causing the problem by following the clean boot procedure that may help you resolve the issue.

  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot
  Step 2: Enable half the services
  Step 3: Determine whether the problem returns
  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns
  Step 6: Resolve the problem
  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135

  After reviewing the issue, put the computer into Normal mode.
  Uninstall or update the program that is causing the problem.

  If you are not able to boot to the desktop, you can try to restore your computer from WinRE.

  1. Insert the Windows Vista installation disc in the disc drive, and then start the computer.
  2. Press any key when the message "Press any key to boot from CD or DVD".
  3. Select a language, a time and currency, and a keyboard or input method, and then click Next.
  4. click on repair your computer.
  5. in the System Recovery Options dialog box, select the drive of your Windows installation and click Next
  6. in the System Recovery Options dialog box, click System Restore.
  7. follow the instructions in the wizard to restore system as usual and choose the appropriate restore point.
  8. click Finish to restore the system.

  Please post back and let us know if it helped to solve your problem.

  Kind regards
  KarthiK TP