Error: "Windows did not start because of an error in the software: load needed DLLS for kernel.

Similar Questions

• Please help, my other computer shows an error message: "Windows did not start because of an error in the software: load needed DLLs for kernel.

  Please help, my other computer shows an error message: "Windows did not start because of an error in the software: load needed DLLs for kernel.

  Hello

  ·          What is the number and the model of the computer?

  ·          What is the service pack installed?

  ·          The meadow of operating system has been installed on the computer?

  ·          Do you remember any changes made on the computer before the show?

  Try the steps listed in the link below: how to fix a computer that does not start: http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx

  You can also check: Error Message: Windows could not start because of the mistake in... : http://support.microsoft.com/kb/326671

• Get the following error on reboot of the computer: Windows did not start because of a configuration of the disk of the computer problem

  Original title: where can I download iso windows xp recovery CD

  I have a file.which damaged boot.ini file later, when I restart it could not start, with the message:
  Windows did not start because of a configuration of the disk of the computer problem.

  Could not read from the selected boot disk. Check the hardware path and startup disk.

  Please check the Windows documentation about the configuration of disk material and your reference manuals of the equipment for more information.
  So I need an iso file XP Recovery.
  I can simply copy the iso files on USB and start with usb?

  Hello

  1. don't you make changes on the computer before this problem?

  First I suggest you try the troubleshooting methods provided in the following article and the check if that resolves this problem.
  Error message: "Windows did not start because of a configuration of the disk of the computer problem.
  http://support.Microsoft.com/kb/314477

• Dual Boot with windows XP Pro with 2 HARD drive, error on secondary windows install: "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check boot path and disk hardware... »

  Hi, I recently bought a new Hitachi 1 TB internal hard drive. I wanted to do a clean install on the new drive (d), be able to dual boot my computer and leave my old 300 GB disk (C :) as the primary windows installation. After physically installing the new HARD drive, I noticed that "new hardware found" and the the brand name flashed in the bottom right corner. I thought I'd see the new hard drive in my computer, but I did not. I initialized the new HARD drive with the computer management window (right click on my computer - manage) and I also formatted in NTFS (I had to change my printer hard drive letter to assign the new HARD drive with the letter D, but I've made other changes after this step). Now, I could see and use in my main windows on the C: installation. I then installed a windows new copy XP pro with the installation CD I got for my C: but on the D: (Note: I have a Dell computer (and the Dell reinstallation CD) and my current version of windows has SP3 while the installation CD is only SP2) (I also reformatted my HARD drive during the installation of windows to NTFS)

  Now when I try to start on installing the new on my D: I get "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check startup disk and hardware access path. "and another line saying to refer to manuals HARD drive and windows.

  My Boot.ini file at this time was:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I looked towards the top of this help page, but for now I'm unlucky:

  http://support.Microsoft.com/kb/314477

  (The next steps I took by throwing from the Windows CD and go into the repair console)

  I tried to use the bootcfg /rebuild but the line to boot.ini for my secondary HARD drive still does not work.

  He gave me something like:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (1) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I also tried to change the signature() to multi (0), but it did not work. (or try almost all possible permutations of disk() and rdisk() partition() 0 to 2).

  I also tried to use expand F(dvd-drive):\i386\ntkrnlmp(I_have_a_duo-core).ex_ D:\windows\system32\ntoskrnl.exe and a few other combinations, but I when I login as D:\windows simply, it fails to extend with a message like "could not develop" or C:\windows I get "restricted access".

  I have not yet tried CHKDSK/r, but since I did a clean install on a newly formatted drive... I don't think it would work.

  I've also marked the partition on the D: as active (in computer management), but it did not help me.

  I've done a first installation of windows repair, strangely, I couldn't fix this one... Still does not work...

  My default windows installation yet works very well & I see that windows has been installed on the D: but I'm ideas from how to operate the dual-boot, can someone throw me a BONE on what to do?

  Maybe try to do something with the Boot Manager (whatever it is?) Create a new partition and use it as a boot manager? I don't really want to do this, because if I made a mistake I will be unable to use my computer and dual boot should work without going through all this trouble... But I found this page: http://technet.microsoft.com/fr-fr/library/ee829686%28WS.10%29.aspx

  Could a clean install two HDD help? I hope I won't have to do...

  Someone has an idea?

  PS: I'm not such an advanced user so I need a solution step by step, thanks!

  Edit: I also noted that I can't see my new HARD drive in my BIOS... weird... SATA-0 is my old drive HARD 1 and 2 are my dvd 3-5 readers are 'off' and it doesn't seem to be anything that it is plugged in. I also have 4 bays for internal HARD disks. Now, 2 are busy.

  Edit2: I looked inside my case and enabled the good Sata in the Bios after a reboot it detected the drive correctly. Dual boot doesn't always work well... The fact that it was disable in the BIOS while I was installing the new HARD drive could change anything? Hmm...

  In case I wasn't clear enough: I had a windows XP Pro installed on my C:, bought a new hard drive and installed the same copy of windows on it (d). I think that should allow me to double boot between the two installs different. Even if for some reason I can't boot from one on my D:. Andrew, I do not understand why you so far physically disconnect the other drive, the point of the whole operation is to build a boot.ini file so that the BIOS knows that it y facilities 2 windows and you allow to choose (and not have conflicting problems between the 2 systems), someone correct me if I'm wrong? "Expand" the part of my first post made reference to one of the solutions provided by Microsoft in the first link that I have included in my previous post (but I can't seem to work).

  In addition, it is the procedure that I followed: http://www.ehow.com/how_5950826_boot-two-different-hard-drives.html

  (except I've had the first installation already done).

  Andrew "also, once a new hd is plugged on the pc & running, most of the BIOS will place (them) as 1st priority hd, set the BIOS to do this", you mean that by installing separately from windows on each unit when the other is not plugged in, I could choose what disk to start from defining their priority in the BIOS once they are all plugged back? It's too tedious (as I intend to move frequently between the 2 installs) and requires a computer to other users of the lack of computer knowledge. Unfortunately, it is not a viable option.

  EDIT: I DID IT! Hmmm... Well, I double checked in the recovery console, the path of the new HARD drive with the arc command Scan. Tried to start again with the MULTI (0) in my boot.ini and it worked... I also had my windows install CD in. Maybe that is why I could not start, windows needs the CD to complete the installation? Weird, I don't know what I did to the difficulty it... but hey, it works! Thanks for your ideas guys!

• How to "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected startup disk... "on a netbook without a CD/disk drive?

  I did a lot of research and unfortunately havnt found a road toward the front of the detroit to a fix. Long story short... I installed Jolicloud as a dual boot with windows xp on netbook gateway of my wife. This netbook has no cd/dvd drive. Jolicloud wanted to screw up the startup option to not allow me to boot into windows, going Strait to jolicloud without option of windows. I tried to change it via the "menu.lst" and Grub.cfg file (I think) the only value I changed was I think 'boot... ". ' value between 1 and 2. When I restarted, then finally got a startup list (although I don't think that my modification of the value gave me the list, I had already installed manually "Grub" via the cmd prompt. I should have just restarted from there without changing anything else... because when I chose 'windows xp' in the start menu... He gave me a black screen and kept going back to the start menu. Then, I tried the "Vista loader" option... hoping that it would some how solve my problem... He asked me if I wanted to run a repair any. I agree with him and when he finished he told me that there is no enough space on the hard disk to copy the files (or something like that) then it froze kind of there. I had to do a hard reboot after that that it froze, then I got the code "Windows did not start because of a computer disk configuration problem. Could not read from the selected boot disk.  check the hardware path and startup disk, please check the windows documentation about hardware disk configuration and your hardware for more information reference manuals.

  Again, I have no drive cd/dvd on a netbook... IM assuming that im going to have to return a key USB with windows boot info to load the Manu F2 at startup... But I do not know... Help, please. Thank you

  Hello

  Follow method 1 and 4 in the article below and check if that helps resolve the issue.
  Error message: "Windows did not start because of a configuration of the disk of the computer problem.
  http://support.Microsoft.com/kb/314477/en-us

  I hope this helps.

• load needed DLLs for kernel windows xp home edition

  I tried to put in the disk of OS widow emachines xp home editon, restarted my computer and did a system recovery, chose to do a full system restore (destructive) I just wanted to clear everything and restore the original settings, and now it says windows cannot load beace of an error in the software: load needed DLLs for kernel and I have no idea what to do any help?

  Hello

  Do you have the XP installation CD?
   
  See links
  Error message: Windows did not start because of an error in...
  http://support.Microsoft.com/kb/326671
  Error Messages When you start your computer if Program Files of Windows are missing or corrupted
  http://support.Microsoft.com/kb/812450
   
  If you have the CD of the CD for scratches check, clean the CD-ROM with a soft cloth and try to install the operating system.
   
  If you do not have the CD you can organize a CD borrowed from a friend or a parent and try to install. You can also contact the manufacturer of your computer.
   

• "When try to turn on my computer: Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid

  Original title: configuration of the CRA

  Hi, I got this message then try to turn on my computer:

  "Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid. "Please check the Windows documentation about the configuration option BOW and your reference manuals of the equipment for more information.

  can someone help me?

  Hi sugenghariyono,

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  ·         Are you able to boot to the desktop?

  Follow the steps in the article.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  For reference:

  Advanced Troubleshooting for General startup problems in Windows XP

• Error when you try to install Windows XP Service Pack 3: "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.

  Windows XP SP3 problem

  Recently, I met a problem with my PC and was forced to use the system recovery. Now I'm back to factory settings and try to install Windows XP Service Pack 3 on my computer. Windows Update won't work for me, that whenever I try to update I get [error number: 0x8024400A]. I think it's because I use Service Pack 2, or that's what I concluded after researching the problem, anyway.

  This is not my real concern, however. Because I could not get the update automatically, I tried to download and install the "Windows XP Service Pack 3 Network Installation Package for IT professionals and developers" myself. The first time I did it, I restarted the PC after the installation and was met with "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this. "  I went into safe mode and went to a just system restore point before SP3 was installed, but now I don't know how to install it correctly without encountering this problem after reboot. I'm hardly the easy just stick with SP2 when there are potentially important available updates. How can I get Windows Service Pack 3 is installed on my PC?

  It's certainly interesting!

  If the cause of your problem is to have a HP PC with an AMD processor and an original image on your hard drive (and of course it sounds like this is the case), the solution should be to rename the file intelppm.sys and launch the sp37394.exe patch. Once done, the SP3 file that you downloaded from here:
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=24
  SHOULD work!
  I'm puzzled why there is no intelppm.sys file in your directory C:\WINDOWS\system32\drivers.
  Since you recently returned to square one with your PC ("return to factory settings"), then you may as well run the patch from this page:
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us&LC=en&DLC=en&softwareitem=PV-60484-2
  and try the SP3 Setup file again.
  But, first, let's be absolutely sure that we are both using the same terminology. Please answer the following questions:
  1. have you safely backed up ALL your data?
  2. what method did you use to ride "back to factory settings? I think that your choices have been a destructive restore (full) and a (partial) non-destructive recovery. The first erases the disk and leave you with a pristine image and NOTHING ELSE (which means that all of your programs and data get deleted). The other (which does not always correctly) is supposed to leave programs and data intact.

• How can I fix "Windows did not start because of...» »

  "Windows did not start due to a problem in the disk of the computer configuration."

  I have re-installed windows XP on my laptop using my USB because the laptop doesn't have a CD player. I used "WinToFlash" which allowed me to convert my installation CD to run on my USB. But no matter what I do I can't fix it. I am very good with computers but I have never encountered this problem. I can not re - install using my USB again because I get the error, and I can't boot the PC because I get the error. When I press a key it just restarts... Any help? Please?

  If you can boot into the BIOS screen, check if the USB is given as a choice of boot.  Do as the first in the boot order.

  Also this BIOS is set by default and if not go back to the default settings (see the owner's manual I don't know what computer you have)

• Satellite M50: Windows did not start because of a corrupted system file

  Hi all.

  I have a problem with my laptop Satellite M50. When you turn on the laptop, a message appears: "Windows did not start because the following file is missing or corrupt: \windows\system32\config\system»

  I am aware of my product recovery CD-Rom and have inserted - however, I don't want to reformat my HARD drive as I have files I back (foolishly) not upward.

  Is there another method to repair the corrupted file without having to wipe all files on the HARD drive? (I don't have an XP CD - the operating system is loaded OEM when the laptop was purchased)

  Thank you very much!

  Hello

  Hmm, using the repair console could be a good way to copy or replace the damaged or missing files on the HARD drive.
  BUT you need to start the console of Windows XP CD of original Startup Repair.
  Without this CD, you will not be able to repair the operating system. The Toshiba Recovery CD contains only image files and does not start the repair console.

  Now the question is; How to back up data.
  You can remove the HARD drive and connect it to the PC second via the external USB HARD disk controller.
  Then you should be able to copy important files on the second computer.
  After backup files you can start the installation from the recovery CD.

  Good luck

• We apologize for the inconvenience, but windows did not start successfully. A recent hardware or software change might caused ha this.

  We apologize for the inconvenience, but windows did not start successfully. A recent hardware or software change might caused ha this.

  Hello ILO,.

  1. When you receive the error message?

  2. are you able to boot to the desktop?

  3. did you of recent changes on the computer?

  Method 1

  If you are unable to start windows check to see if you can boot into safe mode.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Method 2

  If you are able to boot into safe mode then I would suggest that you do clean boot and check.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• We apologize for the inconvenience, but windows did not start successfully. A recent hardware or software change might have caused this. .

  We apologize for the inconvenience, but windows did not start successfully. A recent hardware or software change might have caused this

  My pc does not have a hard drive. I can't restart in any mode.

  Hello

  · What is the number and the model of the computer?

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed on the computer?

  · What options have tried advanced startup options?

  Remove all external devices such as printers and scanners connected to the computer and then try to start.

  As you mentioned you don't have a CD/DVD drive on the computer and you are not able to boot in any mode, there are only two options:

  a. you will need to connect external CD/DVD drive to the computer for further troubleshooting.

  b. you must contact the manufacturer of the computer.

• Equium A60 won't start - error message: Load needed DLLs for kernel

  The problem is the following; in an attempt to start, I get an error message: "Load needed DLLs for kernel.
  Re-install? I made this countless times.

  Following forums, I discovered that this could be a memory problem. However, my laptop has a built-in RAM and I can't change it. I changed that in the expansion without result slot.

  Any suggestions on how to deal with this problem will be greatly appreciated.
  Blessings on you.

  Hello

  Richard's right. Also check it please this document http://support.microsoft.com/kb/812450/en-us maybe it helps!

• Windows XP, computer crash, said to contact technical support, "load needed DLLs for kernel."

  What should I do now that my computer does not start? I tried F8, F10 and reboot... message came on the black screen "please contact the technical support and say" load needed DLLs for kernel. " "I do not have the Windows XP OEM or recover the disk.".

  You will probably need ot to obtain from the manufacturer of the computer for the installation diskettes (which would be less expensive to get a new XP license) and the repair of the operating system or do a new install. Keep in mind that this could have been caused by your failure to drive hard and not because of software corruption.

• help with this error message (load needed DLLs for kernel)

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error message load needed DLLs for kernel in Windows XP
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  ·         When you get this error message?

  Refer to the following articles:

  Error: load needed DLLs for kernel. : http://support.microsoft.com/kb/326671

  http://support.Microsoft.com/kb/812450

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.