eSATA disk not recognized correctly on e9280t.

Similar Questions

• Satellite Pro 6050: DVD player is not recognized correctly

  The guide shows the Toshiba SD-R2102 as one of the internal drives for machine of HRT (supplied with the CD-ROM). So I bought one. Running XP and when I install the hardware is not recognized at boot, or in Device Manager. Looked at the site to support my BIOS is the last and can find no driver there or on my tools disk.

  Can someone point me in the right direction?

  Hello

  As far as I know your device has a Slim select Bay. If the drive is not in a good position and there is no proper contact of the reader doesn t exist for the system. Please check if the disc is in the correct position. If you put it inside at the end to do a click. After that, the reader is correctly positioned.

  Good bye

• 3 TB Canvio Stor.E not recognized correctly in the USB 3.0 port

  I have four of the HDWC130EK3J1 external Stor.E Canvio Desktop HDDs.
  If more than one USB 3.0 drive is connected the partitions are not recognized.

  The GPT partitions are displayed as MBR partition protection.
  The MBR partitions are displayed as never applied.

  The drive is detected correctly after that he was to reinsert and close ofd.
  At the same time, only 1-3 partitions are recognized correctly.
  This problem can be reproduced 8.1 running Win and Win 7 64 bit using two different computers, by using the USB Intel and Nec controller.

  Currently, BIOS, update driver update. The HDDs are checked to find errors.
  Is there an update to flash ready or a replacement for the external hard drive option?
  Please note that a replacement with the same model makes no sense.

  My German Embassy has been blocked so I translated it. Sorry the only translator Google

  There could be a simple answer to this problem:
  There are two standards different MBR and GPT partitions.

  MBR works with drives up to 2 TB in size, but it can record handle t with more than 2 TB of space. MBR also only supports up to four primary partitions if you want more, you have to do one of your primary partitions an extended partition and create logical partitions inside.

  GPT (GUID Partition Table) is a new standard which replaced the MBR. The TPG requires UEFI. This standard isn't limited like MBR and readers can be much larger and size limits depends on the system and its file systems. It allows an almost unlimited amount of partitions.

  I guess that the system cannot recognize the partitions (from additional external HDD) due to the limitation of the MBR.

• New HDD on Satellite Pro L10 is not recognized correctly

  Hello

  I changed my old hard drive (60 GB) with one of 160 GB, but my laptop does not recognize this size. It gives me only 127 GB. I updated my BIOS and update Windows XP SP3 home edition
  I also tried with partition magic. The curious thing is that sometimes, it happens that partition magic sees the 160 GB, I can extend the size of 127 to 160 GB and I can create an additional partition (drive D) of say 40GB.

  When I copy data from this partition I get an error and stops just my laptop.
  After the restart, he says that he cannot find an operating system.

  Can someone help me please?
  Thank you

  Hello

  I'm afraid there is not much to do. Entire HARD disk capacity knows correctly or you must accept that the BIOS can't handle with this HARD drive. This model of laptop is almost 4 years and I can imagine that there is a limitation in the BIOS.

  Maybe you should be happy with 120 GB of HARD drive. And the 160 GB one, you can use as external HARD drive.

  One more thing: have you noticed any functionality problems after installing SP3?

• Satellite A10 - recovery disk not recognized

  I want to format my hard drive and reinstall windows xp.

  Of course, I have Toshiba A10 laptop with HDD 160g, 1 g of Ram, cd/dvd player and the restore disc (cd).

  Problem: the restore disc is not recognized by the cd player. When I insert the disc, then again, boot sequence goes to hard drive and boots from there

  What I did:
  1. check if the reader sees another s cd. Answer Yes, Yes
  2 boot sequence of the bios checked as well as toshiba consoles set up made sure it is
  in "order"hdd, lan, floppy, cdrom", (I tried other combinations starting with cd as well).
  3. I cleaned the restore disc, didn't work
  4. I ordered another set of Toshiba restore disk, which did not work either, still not recognized
  5. I bought a cd/dvd external reader believe it or not, disc starts to work in this case, I get a warning screen shows all data will be lost and asks me to click if I want to continue, when I click it says will now restart the computer and it does but comes back and goes back on the hard drive and boots from there.

  I must also add; When I switch on I get "' pxe e61 media test failure, mof outgoing intel boot agt" msg, according to my search, this problem indicates hard disk.
  but my hard drive does not work,

  Will someone give me an advice?

  If the BIOS is set to boot from the local network first, before trying to boot from the HARD drive, you will see the error PXE.

  Have you tried to clean the lens in the DVD player? Wipe with a Microfiber cloth.

  try holding down "C" when you turn on the laptop, this will make it boot from the CD.

• Re: Qosmio x 770-107 - recovery disk not recognized

  I gave up my old 3 months Qosmio x 770-107 last week and killed my HARD drive. A new HARD disk, exact replacement to order it. Ordered a DVD of recovery of this backup media site that is posted here. I entered number etc.

  Rolled up today but at the start it is not recognize at all. He sees my drive in the BIOS, and I changed the startup as well as preferences to try waiting usual f12 or whatever.

  All I get is:
  "Reboot and select proper boot device."
  Or insert boot media in selected boot device and press a key. »

  It doesn't matter what I do.

  I tried another windows 7 boot cd and it started to load files perfectly. It's infuriating after 8 days of waiting, I thought I was back in business.

  Any help?

  Thank you

  Chelm.

  Post edited by: chelmdog

  > I tried another windows 7 boot cd and it started to load files perfectly.

  This means that you can install Win7 using the original installation disc from Microsoft but Toshiba recovery disc is not recognized at all?

• Re: CD/DVD drive is not recognized correctly on my Equium P200

  I recently bought a laptop P200D and now, I found that the CD/DVD drive is not recognized.

  In Device Manager the drive icon has a yellow on exclamation and in the wealthy area it says "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  I tried uninstalling the drive and then to restart the laptop but it is has not been successful. I recently downloaded and installed the Service Pack 1 for Vista and I have read that there have been problems with device drivers and wonder if there is such a body?

  Are there updated drivers available for this device?

  Thanks for any help you can give.

  Lester Mortimore

  Hello

  Check this thread http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=113742 please

  I hope this will help you.

• Equium A60: DVD - RAM, being not recognized correctly

  Hiya!

  I have an EA60 and my carpet * a DVD-RAM UJ-820 s is currently not recognized by the laptop properly. When I go to device drivers, he said the driver has been loaded but returns the error code 41. I reloaded the Driver and the device, and it makes no difference.

  I also bought a new Pioneer DVD-RAM and it comes up with the same error code.

  Can someone help me please?

  [email protected]

  Kind regards

  Gary

  To start the registry editor
  Click Start, run, type regedit, and then click OK. Start the registry editor.

  Then follows the steps described above.

• DVD player is not recognized correctly - Equium L100

  Can help any 1 Please my DVD - RW is not recognized in my system. Sometimes I boot and it is there, but other times I start up and it is not shown in my computer or Device Manager
  
  Seriously frustrated.

  Hello

  Please try this http://support.microsoft.com/kb/314060/en-us

  Is the DVD drive in the device with the yellow exclamation point Manager?

• Connected to the Portege 3500 USB DVD burner is not recognized correctly

  I am trying to connect a burner DVD HP DVDv 940th my 3500.When Portege I plug in the device, it is not recognized and the Device Manager list as a storage of unknown mass without a driver. Where can I get this driver?

  Hello

  Try to check the assumption of the manufacturer or the download page. Manufacturers of portable gift use support external devices t produced by other companies.

• DVD - RW for Satellite 2800-500: IDE1 error, disk not recognized

  Installation of a slim drive DVD - RW NEC ND6500 caused a message "Error IDE1" at startup and the drive was not recognized.
  The DVD-RW Toshiba SD - R6472 drive is not compatible with my Satellite 2800-500?
  Does anyone know a way to make someone of them work?

  [Edited by: admin on 22 July 05 17:57]

  Hello

  The problem is that all CD/DVD drives cannot work spirit all models of laptops. The problem is that there is no way to change to master or slave. AFAIK there is no public document that shows the discs and laptop computer compatibility.

  The best solution is to check if the drive is CSEL. In this case, it should work properly. If you can check please if you can find the CSEL notation on the label located on the upper side of driver s.

  Good bye

• 160 GB external hard drive of Gigastore is not recognized correctly

  Hi, hope someone can help me!

  I bought a 160 GB external drive Gigastore hard today, but the plug inside, the computer did not recognize it. In fact, nothing happened. I tried all the usual as control to see if it was in my computer and then right click my computer, manage, etc computer management, but again, she did not show. I tested it on another pc and still does not work. I'll put up the wires correctly, so this isn't the issue.

  When I turn on the power, the hard drive light constantly flashes blue. I would have thought that will be that the hard drive has been slowed down, that he would stay on continuously without blinking. Could someone let me know if this blinking determines that the disk does not just and it is indeed tired?

  Phil

  Hello

  It seems that it s not a laptop fault because the other laptop or PC can not recognize the external HARD drive.
  Have you checked if some additional drivers or tools were shipped with this external HARD drive device?
  If please connect the HARD drive and use the Add Hardware option

• New 500 GB HARD drive is not recognized correctly

  What is happening, I replaced the drive HARD than Go 150 original after about 18 months, again, now a year later, that the drive seems to have died too, so I bought a new seagate 500 GB drive HARD for it, the BIOS said it s it, but vista CD dies just when it is trying to install, CD WXP can t see the drive at all, but I expected that when WXP is older , but Vista I expected to work.

  So here's the thing, I put the new HARD drive in my desktop PC and he found in the BIOS no worries, then I started the Vista CD and again no probs, Vista installed without worries, then I put the HARD drive in the lappy and once again he can t read it, so it s not a Vista thing , it seems that it s the lappy itself

  Is this a problem with the Toshiba BIOS, or is it a physical problem where the Toshiba is struggling in reading ANY player?

  It s driving me crazy.

  And what model of laptop do you have?

  Generally upgrade HARD drive should not be a problem. I assume that your laptop's HARD drive with SATA interface and I sure you bought the right of Mr. I've upgraded or because of the experiences on several laptops equipped new hard disks and all of them were still properly recognized and I was able to install original Toshiba Recovery (recovery DVD) on this subject image.

  Maybe you have an older model A200 and perhaps he has some compatibility issues with new hard disks. I will be 100% sure works perfectly with HARD drive up to 300 or 400 GB maybe.

  Do you use Toshiba Recovery for the Vista installation disc or original disc of Microsoft?

  BTW: WXP is unclear due to lack of driver SATA HARD drive.

• Satellite Pro 6100: disk not recognized HARD - error IDE #0

  I just replaced a failed HARD drive from MK4019GAX in my 6100 Pro of the Satellite with a MK4026GAX and have tried to install XP Home. I can't recognize the hard drive of the computer.

  When I boot, I get a message ERROR IDE #0 before installing Windows, then a message saying that all third party SCSI drivers should be installed first. (I'm starting with the Windows disk in the drive) then when it is at the end of the installation process a message saying that "put in place did not any hard drives installed in your computer.

  If I boot without the Windows I'm getting PXE - E61 Media test failure.

  When I go into the BIOS ACPI BIOS version 1.90, under devices "Mode HDD = used (s) ' I can't get in to change and there is nowhere else that seems related to the hard drive (apart from the boot priority section).

  I read on a forum somewhere that there could be problems getting the BIOS to recognize a new HARD drive.

  It is a common problem for this model, or is the new hard drive may be defective?
  Is there a workaround or a solution?

  If all requested assistance right.

  DM

  Hello

  This error message indicates that the HARD disk drive was not properly acknowledged. The fact is that this unit uses a regular IDE (ATA-5) interface and the new HARD drive is supported by this interface.
  In this case, I assume that the HARD drive has not been installed correctly. Try to remove the HARD drive and check the connections.
  The other possibility is that the HARD disk controller is dead.
  In this case, the service partner must check the laptop.

• Satego X 200-TS-L632D is not recognized correctly

  Hello (unfortunately once more!).

  Looks like I'll have bad luck with my laptop. Now my DVD drive just did format or burn any type of media. I tried many solutions but nothing. Updates of the firmware on the Toshiba Driver Site are for TS-L632H and TS-L802A. None of them worked for me. I want to try absolutely every alternative before returning to the shop...

  Ideas?

  Thanx

  One last thing, Windows does not recognize it as a drive of DVD, but as a CD drive

  Hello

  It s like your CD/DVD drive is not properly recognized.
  Have you tried many solutions? It s interesting to know so tired this already:

  -go the Device Manager and remove the CD/DVD drive
  -access the registry using the regedit command
  -Choose this registry key
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
  and delete the Upperfilters and Lowerfilters completely values
  -Reboot the laptop

  Good bye