ESXi 3.5 does not not in the CR

Similar Questions

• ESXi 4.1, does not use the entire RAID 5 on Dell R810 datastore

  I installed ESXi 4.1 on a Dell R810.  I've raided the first two drives in a RAID 1 and installed ESXi.  The 4 remaining disks are in a RAID 5 for the main data store.  ESXi acknowledges that the RAID is 2.7 TB but will only create a.7 TB or 744,75 GB data store.

  I did the same thing on several Dell R710s without problem.  Someone at - it ideas?  I guess it's a driver issue, but I do not see updates to driver for 4.1 for Dell R810

  The maximum size of a 4.1 data store is 2 TB less 512bytes. If you want to see the entire data store, you will need to upgrade to ESXi 5

• A Dell PowerEdge 2850 server is used for the new ESXi server, but it does not support the 64-bit VM.

  A Dell PowerEdge 2850 server is used for the new ESXi server, but it does not support the 64-bit VM.

  I can't believe it.

  When I start up a virtual computer, it gives a wrong message shown in the picture below.

  Does anyone have any ideas on this?

  Usually not enabled virtualization technology in host BIOS.

  Take a look at can not power on a 64-bit Windows VM

• ESXi does not recognize the cd/dvd on HP DL380

  I'm new to the hypervisor and really need some advice on a DL 380 I put up as a box QA. After installing ESXi 3.5, I created the virtual machine I need and proceeds to start a virtual machine, but was surprised to see that the server does not see the CD drive? I guess that would not as surprising, if it's a customized version white box, but a HP DL380, only one of the most common servers in the world?

  Anyone has any advice or suggestions about what is a hotfix for this.

  Thank you

  Robert

  In addition, once you can convert many of your applications and or OS installs in ISO format, you can just use your Infrastructure Manager client and connect an ISO to some VM you must have a 'CDROM' inserted in to.

  For example, if you install Citrix and you have an ISO copy locally or on your network, you can simply start the virtual machine and then click 'connect/disconnect devices on CD' point to your ISO image. VMWare then moved the 'CD' for the virtual machine and it will be accessible as would a normal CDROM.

  When you do that, your local CDROM in the ESX box really is not used for a lot more outside upgrades to ESX 3.5, and even what is done remotely today for ESX 4.

  Hope this helps

• Storage Array Type Config path: ATAS VMW_SATP_SVC does not support the configuration of the path on ESXi 5.0 u1

  Hello

  Below for the output of my blade IBM HS22., are there any problems with the configuration of the path.

  List of paths esxcli storage nmp
  SAS.5005076b08b7aaa4 - sas.a9501097faba7a - naa.600508e0000000007abafa971050a900
  The Runtime name: vmhba0:C1:T1:L0
  Feature: naa.600508e0000000007abafa971050a900
  Full device name: FREE Serial Attached SCSI (naa.600508e0000000007abafa971050a900) drive
  Group status: Active
  Table priority: 0
  Storage Array Type Config path: ATAS VMW_SATP_LOCAL does not support the configuration of the path.
  Path selection policy path Config: {current: Yes; favorite: Yes}

  FC.2fff0000c900009f:2ffd0000c900009f - fc.500507680100 b b 680 680:500507680130 - naa.60050768018105afc000000000000df0
  The Runtime name: vmhba2:C0:T3:L2
  Feature: naa.60050768018105afc000000000000df0
  Full device name: disk of IBM Fibre Channel (naa.60050768018105afc000000000000df0)
  Group status: Active
  Table priority: 0
  Storage Array Type Config path: ATAS VMW_SATP_SVC does not support the configuration of the path.
  Path selection policy path Config: {current: Yes; favorite: Yes}

  Kind regards

  Surya

  Hi Surya,

  No, it's not any problem with the configuration of your path.

  It only means that this policy does not allow additional configuration.

  I.e. with fixed NMP, you would be able to configure a preferred path allowing you to manually distribute the i/o load.

  Your current configuration does not offer this option.

  Kind regards

  Ralf

• ESXi 5.0 - do not save the changes SD. changes after restart

  Try to solve problems with USB passthrough and needing to make changes to the configuration. Whenever a change is made, it is destroyed after a reboot.

  After digging around the shell, it seems to me that the system uses local.tgz configuration instead of/bootbank/state.tgz file. Ive brought changes, and each time I checked these files. In the esx.conf file I see that nothing changes on the file local.tgz but it does on the state.tgz file. This may not mean anything, and I could look at this all wrong. I confirmed that backups are spend the hour + 1 min and I made manual backups with the script/sbin/auto - backup.sh.

  One thing to mention is that when I do edit and run the auto - backup.sh I see that it lists the changes, and I see that it is what I guess it is in the file local.tgz.

  I read a number of different ways to this address, but none seem to be able to help.

  I have attempted to copy the file state.tgz on the local.tgz file and change the permissions on it. To restart, local.tgz file returned to the date that was the 13th but the state.tgz file remains to day it seems.

  I think I should be able to point just sort the system starts on the state.tgz file but I don't know if this is possible / should already be the case / makes sense given that we use an SD card to begin.

  I read in this document http://www.vm-help.com/esx41/adding_files_to_state_tgz.php that if you use an SD card, it will start on the local.tgz file.

  I used this guide http://store.vmware.com/store/vmware/en_US/DisplayProductDetailsPage/ThemeID.2485600/productID.28435970

  to see if I could adjust the location of the file... scratch that change does not persist after a reboot.

  I think that the only way I could solve this problem is to start on an iso of linux and to make changes.

  Any ideas on how to solve this problem or there at - it a way to indicate to the synchronization local.tgz and state.tgz system?

  Thank you.

  I got the problem solved.

  For all those who need assistance on this I hope this helps:

  Found that when under the configuration of host-> advanced if USB devices are passthrough value, they will not be monitored by the usbarbitrator service. This service allows for the virtual machines to use USB devices.

  I could not change it because the system does not update the SD card when configuration changes are made.

  Two options:

  Edit the file esx.conf on the SD card

  or

  Re-install ESXi

  I went with option 1.

  used this post

  How to disable Passthrough ESXi my conclusions

  Ubuntu iso desktop to live starting in the system.

  From there on, I was able to edit the files and restart ESXi. This fixed my issue.

• The destination does not support the EFI firmware.

  Hello

  I have a Debian Linux 7.0 physics I'm P2V using converter 5.5.3.  When I choose my target ESXi server, I like:

  The destination does not support the EFI firmware.

  How confirm/deny, or enable the EFI on my node ESXi support?

  Hello

  This may be a false signal. The problem is that Debian is not a taken GOS supported for the converter. That's why he treats her like "Other Linux" and then the ESXi responds that it does not support the "other Linux" on EFI.

  Unfortunately I see no significant workaround solution. There is a crazy idea - converter checks if the source computer's BIOS or EFI by searching the directory/sys/firmware/efi/vars. If you can somehow it wrong that there is no (I don't know how), it might treat the source such as BIOS and convert it. When this happens, you should then change the VM of destination to EFI firmware and manually create the EFI boot entry somehow.

  Concerning

  Plamen

• ESXi 5 Server does not recognize HP StorageWorks 81B HBA

  I'll put up 4 ESXi 5 servers attached to a HP P2000 SAN. I'm quite familiar with ESX and VMware. have been running ESX 3.5 for about 3 years. This new environment gives me a problem that ESXi 5 does not see the HBAs HP StorageWorks 81 b installed on servers HP Proliant DL 380 G7. I see that it is a known issue and I have been tring to follow the directions outlined in the RFSO HP (see link below). I the document is poorly written and not very clear. I'm stuck at step 3 where it says:

  "Install the HBA driver. Download driver HBA Brocade, extract the compressed file and burn (or climb) the ISO image. Download and install VMware vSphere CLI. Open the CLI and change directory C:\Program VMware vSphere CLI\bin .

  Run the following command and check do not omit the dot and bar backslash:

  ".\Vihostupdate.pl server 10.12.243.130 - - root username - - password Password1-- install - - bundle E:\offline-bundle\BCD-bfa-2.3.0.2-00000-offline_bundle-344638.zip"

  I downloaded the ISO file and the file and the path "offline-bundle\BCD-bfa-2.3.0.2-00000-offline_bundle-344638.zip" exist on the CD but when I run the command in the CLI, it says "error connecting to the server" ". https://localhost/SDK/WebService ' ' host is perhaps not a vcenter or ESX server. I try to run it from a Windows Server that is not a vCenter server but how I go this from a vCenter server if I can not see the HBAs and therefore cannot see the SAN and am not currently in a position to implement the vCenter server. I also replaced the 10.12.243.130 IP address IP address of the ESX Server and that has not worked, and of course, I entered the correct password for the field 'Password1 '. I could run this command from the ESX Server, if so, what would be the command line? In any case, I'm stuck at this point. I called HP support and they were no help at all.

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en & CC = UK & TaskID = 110 & prodSeriesId = 3662826 & prodTypeId = 12169 & objectid = c02773230

  According to HCL, the adapter is not supported on ESXi 5.0.

  However it looks like there is a driver for ESXi 5.0 to http://downloads.vmware.com/d/details/dt_esxi50_brocade_bfa_3000/dHRAYnRqdGpiZHAlJQ== that you could try (at your own risk) rather than the one you mentioned. Installation instructions are included in the zip file.

  André

• "Your host does not support the current settings for comments.

  My requirement of virtualization are demanding very high resolution on a Win2000, ESXi host guest.  I upgraded, using the stand-alone version of converts, but I can no longer switch to full-screen (the scale).  I get the following message:

  -

  ---

  Error

  -

  ---

  Connection error: your host does not support the current settings of comments in mode full-screen.  Try to reduce the color depth or resolution of your guest and try again.

  Impossible to enter full screen mode.

  Do you want to retry?

  -

  ---

  Yes No

  -

  ---

  Does perform a work around?

  Thank you

  Alan

  The vSphere client is a terrible Viewer. Very slow. W2K is also a limitation. Take a look at the other viewers if RDP is not suitable. Radmin is one I've used several years ago.

• P2V then "an IDE controller is found, but the VM does not support the option.

  I am very new for ESX and ESXi. I am trying to convert the server running (really a Dell PC) to a virtual machine that runs on ESXi (we are in phase, about to move all real servers ESX or ESXi, if we love him test). After a conversion on the server, by using the agent option in VMware vCenter Coverter Standalone version 4.0.0 I get the following error when attempting to change the virtual machine to 'clean up' after the P2V conversion.

  An IDE controller is found, but the VM does not support the option

  ESXi is version 4.

  Any ideas? Google is of no help for the exact error.

  Try to use the latest converter, 4.0.1 instead.

• Why Safary does not load the content of pages?

  Why Safary does not load the content of pages? I mean, when I hover over the places where should be the content, he is always showing the "redirect to: [email protected]/" lower left. My Safari is 9.5 and worked fine until Safe Fimder Virus get inside my computer. Mozilla Firefox is a bit slower. If someone could give me an idea on how to deal with it, I would be happy.

  Sorry if my English is not good, I am a Brazilian who is still learning English

  Your English is very good!

  Redirects are usually due to adware or malware.

  Download the run MalwareBytes.

  It of free and takes only a minute or two. Which should remove all adware and malicious software on your Mac.

• Time Machine (on Mac) does not detect the airport Time Capsule

  Originally posted on the page of the airport, but seems to be the better question for this group. Sorry for the double post

  Looking for advice on how to get the Time Machine utility for access to my Time Capsule. I use an iMac in late 2012 with MAC OS 10.12 TimeCapsule is 2015 7.7.7 running latest firmware. Airport utility is the latest firmware 6.3.7.

  When I run the application Time Machine, Time Capsule is not detected. I tried the two WiFi and with cables connected Ethernet (not tried USB yet) and my Time Capsule doesn't have a lightning bolt or firewire ports.

  Open Airport utility & see the airport time capsule. I can see all connected devices, including the MAC, but no prompt activation Time Machine on the Time Capsule.

  I recently used TM on this iMac with a G-Technology drive. It auto detects the time machine and executes a back up. But airport Time Capsule will not.

  Any suggestions?

  Sierra has been problematic with the TC.

  1. make sure you don't have any charge virus protection software. In fact, I would say that disable all software 3rd part at the moment.

  2. make sure that you can actually write to disk of TC.

  Attach the TC disc in the finder and copy a file on disk, you can delete it later... It's just to ensure that you have full write permission. If it does not for the most part, you won't be able to use Time Machine... If you can then try TM immediately...

  Just to be clear, the TC is a network device. You have tested with ethernet and wireless... Ok.. They are only suitable methods. You cannot use USB. And clearly, TC has never had nor will never be ports Firewire or lightning.

  3. no chance that a reset complete TC. This will not delete the files on the hard drive, but you must make sure that the device is configured on the current computer.

  4. There are many positions in these days... read through them and do some research. Sierra is a bleeding edge new... So wait you to spend a lot of the precious liquid if you choose to be an early adopt.

• the preview window does not show the document that I'm about to print in Sierra

  The preview window does not display the document that I'm about to print. This problem started as soon as I upgraded to Sierra. It occurs in many applications - including in Microsoft Excel 2011.

  

  

  Hello, David Bry1,.

  Thank you for using communities of Apple Support.

  I understand that when you try to print from a number of different applications, you do not see the preview of the document you are printing. I would like to assure you that I see the preview as well when I print. Let's see how we can get this resolved.

  I advise you to ensure that the printer software is up-to-date on your printer Brother DCP-7065DN. Please choose 'Available Software' brother printer and scanner software for macOS Sierra, El Capitan, Yosemite, and Mavericks

  If a software update is available, please install and then test and see if you get the same result.

  Have an amazing day!

• Why my iPhone 4S (ios 9.3.5) does not activate the messages using my apple ID?

  Why my iPhone 4S (ios 9.3.5) does not activate the messages using my apple ID?

  Michael T.L. says:

  Why my iPhone 4S (ios 9.3.5) does not activate the messages using my apple ID?

  If you get an error when you try to activate FaceTime - Apple Support or iMessage

• IPhone does not accept the code to check for text messages

  II phone does not accept the code verification for the transfer of messages text imac

  Maybe these articles will help:

  Get a verification code and connect with authentication to two factors - Apple Support

  If you don't receive your check or reset email - Apple Support

  If this is not the case, can you explain a little more detail what exactly is your problem?  Or see the 'Contact us' at the bottom of the second article.

• Power mac g4 does not recognize the DVD/CD drive.  It has worked very well in Leapard

  I just newly installed Tiger on my PowerMac G4, and now it does not recognize the DVD/CD drive.  I did all the updates and it does not see the DVD in the DVD drive.  It works perfectly before a new clean install DVD of the Tiger.

  What is your indication that the DVD is not recognized?

  Run the utility disc with the disc in the optical drive.  The drive will appear in the sidebar of disk utility?

  I did all the updates and it does not see the DVD in the DVD drive.

  If you put another type of disc in the optical drive, as a music CD, it is recognized?