ESXi 5.5 - Direct access to the local logical unit number

Similar Questions

• The Systems ESX 3.5 and ESXi 4.0 share the same logical unit number?

  We started the upgrade to vSphere; vCenter just so far. We don't have to level the ESX 3.5 servers yet, but add new servers ESXi 4.

  Can we expose the SAN disk to hosts containing virtual machines running on 3.5 4.0 and supply the new virtual machines for ESXi 4 on the same disc?

  In other words, is there any change to vmfs or differences in VM structures that prevent new and old sharing storage ESX hosts?  Obviously we would expect not interchangability VM, until we improve the ESX 3.5 hosts and the virtual machines running on 3.5.

  THX

  Yes, you can share the LUNS and configure new virtual machines on the same disk.

  You can even VMotion VMs between 3.5 and 4.0 if VMs are hardware worm. 4 (have all virtual machines created in 3.5).

  ---

  MCSA, MCTS, VCP, VMware vExpert 2009

  http://blog.vadmin.ru

• Different operating system on the same logical unit number?

  I have a 3 esxi and SAN shared storage servers. On storage, there are a few LUNS shared between several VMS with different OS.

  It is a good practice to hold the similar OS on the same LUNs, for example Windows XP or 2003 virtual machines on a LUN, LINUX on other ther?

  You ask people to guess what should be your storage configuration. You should talk to your San and using the IOPS tested engineer / s.

  LUNs must be more small thane 2 TB (2 TB-512 b)

  Regarding the mix of BONES, once again, it should be with the results of the tests on which the OS will on that LUN.

• vSwitch ESXi 5.1 workaround to virtual machines (direct access to the network)

  Hello world!

  I have a server running properly the 5.1 ESXi hypervisor and got inside the physical grid active router with DHCP. How can I configure the vSwitch on ESXi 5.1 work not managed on the network, without VLAN and have direct access to the network?

  Just to clarify, I would like to first of all virtual machines VMware Workstation works - if it is possible to run several virtual machines and define all NICS (Network Interface Card) as connected by a bridge, that is to say. Each VM gets the specific configurations of IP to the external router.

  Since now, thank you very much for the help!

  Best regards

  Eduardo

  With ESXi the vSwitches work comparable to Bridged networking, so there is really nothing special to do.

  André

• ESXi allows to directly access the disk?

  Two quick questions...

  (1) ESXi allows to directly access the disk?

  .. .and associated with what precedes :)

  (2) Let's say I want to use Windows Home Server as a guest within ESXi operating system.  It formats the disks using standard NTFS that can be read by any Windows machine.  (eg. you can remove the hard drive of the server and paste it into any other computer and you can read it).  How would this work in ESXi?  ESXi would force first all of the disk formatted to VMFS and then have NTFS below?  (so you could not "access the drive except in other machines on ESXi)

  Thanks for any help!

  However, if I create a virtual disk (using VMFS) that even if the virtual disk is formatted NTFS by the client operating system that he still cannot be read in another computer because it is in a 'container' of VMFS.

  Yes, I would say that's pretty accurate, there are a few exceptions of course... but overall, Yes.

• blocking direct access to the oracle server

  Dear Sir

  One of our condition of pci - dss to stop direct access to the db. One solution I know:

  TCP.validnode_checking = YES

  TCP.invited_nodes = (192.168.1.91, visionhost.solutionbeacon.com)

  But this option will allow the IP address of the node invited with sqlplus using tns names also. Have any have experience to solve the problem of ending up with pci - dss?

  In which paragraph of the PCI - DSS doc that makes you think that there is a problem? I work with version 3.0 (November 2013) and I can't find anything like that. For example, paragraph 8.7 c, "review of database access control settings and application of database to verify configuration settings that the user access directly to the or queries of databases are limited to database administrators" does not say that the DBA is not able to connect to the application server. And all the stuff of firewall in requirement 1 close the access to the network and between networks, not within the network.

  Are you sure that you have a problem? There is no interest to 'fix' something that doesn't have a reference in the doc.

• Move the file to the vm to a logical unit number to another logical unit number

  How can I move a vm folder in a logical unit number to another number of logical unit to a remote domain with powercli controller?

  the virtual machine is not registered in vc

  Hello, tdubb123-

  You can use the cmdlet Copy-DatastoreItem of PowerCLI, who has a "-Recurse" parameter to copy all the child elements.  For example:

  Copy-DatastoreItem -Item "vmstore:\myDatacenter0\myDatastore0\someVMFolder0\" -Destination "vmstore:\myDatacenter3\myDatastore2\" -Recurse
  

  "He uses the PSDrive" vmstore:------", which gives access to centres of data/connecting to VIServer default data warehouses.  If you go between vCenters, you can use the ' vmstores:------"PSDrive, which allows access to these objects in all VIServers to which you are connected in this particular PowerCLI session.

  Once you are satisfied with the integrity of the files after copying, you can delete the folder of elements from the original location using the standard Remove-Item cmdlet.  Enjoy.

• Logic unit number must be manually replaced by the iSCSI initiator

  I have a VM server that once restarted the logic unit number must be manually replaced by the iSCSI initiator. Does anyone have an idea how I can get this auto re - join when the server is restarted?

  EqualLogic PS4100

  Win2008 R2 64 bit server VM

  When you logged into the volume, there is a checkbox to restore the connection.  It was supposed to end upward in the Favorites tab in the MS iSCSI initiator utility.

• Determine if the logic unit number is in use

  Is there a way to determine if a logic unit number is used on a case of ESX?

  I'm cleaning up some old RDM LUN presented to on my ESX servers, and I want to confirm that they are not mapped to any virts. Is there a way of gui to do? I tried to develop a bash script to do, but the problem is somewhat difficult.

  --

  Jeff

  VCP4

  Hello.

  Any ROW that are not attached to virtual machines is available by using the Add Hardware Wizard.  Try adding a hard drive to a virtual machine and choose "Raw Device Mappings" (if not grayed out) and anything that is listed is not in use.  If Raw Device Mappings is grayed out, you can use the free RVTools to find what VM has the RDM.

  Good luck!

• Secure access to the local database of HTML5

  Hello

  I have a client who is the main concern is safety. I look at using local databases webworks and html5 to store sensitive data. I would like to know if the local databases are encrypted with the key signature application? If I were to write a native java application so I know that I can directly access the SQLite api and specify encryption. However with the html5 databases it seems not be the option.

  I if I understand correctly, the local databases are implemented with Google Gears on OS 5 and SQLite for OS 6 and more. I need a solution that works for both. I prefer not to use custom js extensions, but if it's my only option.

  Does anyone have information about this?

  Encryption must be done through the extension. The implementation of SQLite on the smartphone supports encryption, but does not include the HTML5 specification for the database.

• ASA5505 can transfer clients to remote VPN access to the local network

  I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

  Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

  These two cases are possible? :

  (1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
  (2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
  Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
  Thank you.

  I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

  You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

• Client remote access VPN gets connected without access to the local network

  : Saved

  :

  ASA 1.0000 Version 2

  !

  hostname COL-ASA-01

  domain dr.test.net

  turn on i/RAo1iZPOnp/BK7 encrypted password

  i/RAo1iZPOnp/BK7 encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP 172.32.0.11 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 192.9.200.126 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  nameif failover

  security-level 0

  192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

  !

  interface Management0/0

  nameif management

  security-level 0

  192.168.2.11 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain dr.test.net

  network of the RAVPN object

  192.168.0.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.200.0_24 object

  192.168.200.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.9.200.0_24 object

  192.9.200.0 subnet 255.255.255.0

  the inside_network object-group network

  object-network 192.9.200.0 255.255.255.0

  external network object-group

  host of the object-Network 172.32.0.25

  Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

  access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

  access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

  access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

  192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

  pager lines 24

  management of MTU 1500

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) source Dynamics one interface

  NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

  Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.9.200.0 255.255.255.0 inside

  Telnet timeout 30

  SSH 0.0.0.0 0.0.0.0 management

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 66.35.45.128 255.255.255.192 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 30

  SSH version 2

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal RAVPN group policy

  RAVPN group policy attributes

  value of server WINS 192.9.200.164

  value of 66.35.46.84 DNS server 66.35.47.12

  VPN-filter value test123

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value test123

  Dr.kligerweiss.NET value by default-field

  username test encrypted password xxxxxxx

  username admin password encrypted aaaaaaaaaaaa privilege 15

  vpntest Delahaye of encrypted password username

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  Group Policy - by default-RAVPN

  IPSec-attributes tunnel-group RAVPN

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory 2

  Subscribe to alert-group configuration periodic monthly 2

  daily periodic subscribe to alert-group telemetry

  aes encryption password

  Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

  : end

  COL-ASA-01 #.

  Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

  Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

  25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

  29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

  38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

  56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

  69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

  98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

  99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

  108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

  115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

  116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

  COL-ASA-01 #.

  Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

  And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

  Hello

  The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

  You can try the following changes

  attributes global-tunnel-group RAVPN

  No address RAVPN pool

  no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

  local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

  In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

  the object of the LAN network

  192.168.200.0 subnet 255.255.255.0

  network of the VPN-POOL object

  192.168.201.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

  NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

  You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

  No source (indoor, outdoor) nat Dynamics one interface

  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

  Hope this helps

  Let me know if it works for you

  -Jouni

• direct access to the modem point

  is it possible to directly use the access point with a modem.  my router seems to slow down my internet connection.  If I connect directly access point, I can still access the internet with my laptop, but my xbox comes up with an error "no IP".  any advice?

  Yes and NO

  An access point is designed to be a network of signal and therefor if the WAP54G was connected to your moen he will be part of the public network like all clients attached to it. This means that all customers should also public IP provided by your ISP.

  Your ISP probably would not be in favor of offering more than 1 IP because there is a finite number of available IPv4 IP and there is a growing shortage of IPv4 IP addresses. This is the reason why IPv6 is developed.

  Concerning

  Fred

• cannot access shares the local computer

  Hi-

  Win7 64 bit.   I use homegroup, and I have this Win7PC on my local network with XP and Vista PC.  I can see the 2 other PCs on the Win7 PC and get to their shared folders.  None of them access to the part of it.  I have the name of workgroup defined correctly on all (including this PC Win7).

  In addition, oddly enough, on the WIn7 PC, in WIndows Explorer, I can navigate to C:\Users\Public BUT if I try to go into WIndows Explorer, then fall below computer - C: to the network and open it, I see the other 2 PC and the local PC.  The WIn7 PC is called "kirk".  So, in network - Kirk, IF I open it I see 'users' share.  BUT if I click on it, I get the error:

  \\kirk\users is not accessible.  You might not have permission to use this network resource.

  I am logged in as administrator (on Kirk).

  So, to rephrase, I am connected to a Win7 PC as an administrator.  I can navigate to C:\Users\Public in WIndows Explorer.

  BUT if I go to "Network Neighborhood" in WIndows Explorer (it's actually just "network") I see the local PC named Kirk.  If I click on it, I see 'User' (share).  I can't go to see 'public '.

  To make things more awkward, I could access it until a few days ago and I has not installed anything new, although WIn7 can be updated automatically.

  Help!

  Thank you

  Kelly

  Hi-

  Thanks for the list of things.  There was a lot of good links in there.  I went through everything without the blinkers "it worked before" and "I won't change anything" on each link there is, I've lived and all checked.  The only one I had to do something opened ports in my firewall mcafee.

  Nothing helps.

  This PC is named kirk and I still don't see files shared this PC itself in windows Explorer - network\kirk. for me, very odd, I am connected to kirk as an administrator.  I open Explorer windows on kirk.  I can see c:\users\public in windows Explorer, but I do not see network\\kirk\users

  so, I thought, let's start over.

  I went to the center of network share and changed "active network" of the type "work network" type "home network" and it is now.

  working group name has not changed so it's always "the Star", so I can see all the other no WIn7 PC and PC WIn7 himself can see that it is me in network neighborhood.

  I'll reboot and be sure to x 2.  very weird.

  Thanks for your help!

  Kelly

• Windows 7 Pro seddenly denies access to the local settings folder

  I log on my Win7 PC as an administrator and sometimes see the subfolders and files in my Local Settings folder. There has never been a problem for several years. But a few days ago I tried to navigate to the outlook.pst file is stored, but clicking on the local settings folder generated the message "local settings is not accessible. Access denied. "

  I haven't changed my user profile since I implemented this PC in 2011 and have not changed the password in quite some time. My only recent system change came after I received a warning from Windows Tuesday that trash has been altered. To resolve this problem, I followed the steps in a thread of Microsoft Answers by activating the display of hidden system folders and files, and then deleting the file $recycle.bin. Windows regenerated the trash and I disabled the display of hidden system files. The next day, I discovered my access problem.

  What should I do to fix my access?

  Thanks for letting us share this resolution.