ESXi host does not connect more after a restart of the service LogInsight

Similar Questions

• vSphere client using the name Netbios on ESXi host does not connect using the credentials of a Windows session

  I have 3 ESXi 5.5 hosts, all connected to a single server vCenter, where we try to authenticate directly to the host by using the windows logon credentials. I have installation of the Administrators group of ESX and filled with the admin accounts that I want to be able to authenticate to the host. The Netbios name of the domain is tstdomain (for example) where the domain name is tstdomain.com. If I connect directly to a host and check the checkbox 'Use Windows Session Credentials', the vSphere client will default by using the Netbios name of tstdomain\adminusername and the connection will fail indicating that the username and/or password is incorrect. If I enter the domain name of tstdomain.com\adminusername, I am able to connect to the host without error.

  Does anyone know how get past that this matter have the vSphere client uses the domain name or to use the Netbios name and connect with the credentials to active directory? I looked by editing the file/etc/hosts and checked that the SPN of the host is correct in active directory with the command hostname setspn - l, with no luck on one. I also tried to change the field of research for the Netbios name of tstdomain rather than the tstdomain.com domain name, also did not work.

  Thanks in advance for your suggestions on how to correct the problem.

  Seems that this issue was due to a slow network and the connection timeout when you try to talk to the domain controller. I am able to connect with windows creds now, but the connection is very slow. I increased the default period of 30 to 60 seconds to help work around the problem.

• I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

  Turn off the new modem for at least 30 minutes. More is better.

  Perform a hard reset on the AirPort Extreme, then it turned off.

  Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

  After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

  Then, turn on the airport and let it run a few minutes

  Set up AirPort Extreme again

  Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

• I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  original title: alternate tcp/ip

  If by "alternate TCP/IP configuration" you mean the settings on this screen--> http://tinyurl.com/42kbqqz, then, to quote Inigo Montoya, "you keep using that Word. I don't think it means what you think it means. »

  The 'alternative' configuration settings tab, if you select "IP address private auto" (APIPA) or "specified user" is only used IF "obtain an IP address automatically" is set on the tab 'General' (http://tinyurl.com/8p9hn) AND the adapter cannot get an IP from a DHCP server.

  Most cable networks use a DHCP server to automatically assign IP addresses.  In this case, just plug your Ethernet cable and you're automatically configured and connected.

  If the problem is that your network requires a static IP address (that is, they use a DHCP server to automatically assign IP addresses), you will need a third-party network settings manager.  If you have an IBM (Lenovo) ThinkPad, you can use "Dial-up connections." IBM Otherwise, see this Google search (I have no experience with any of the applications shown, so I can't comment about them): http://www.google.com/#sclient=psy&hl=en&source=hp&q=network+configuration+switcher&pbx=1&oq=network+configuration+switcher&aq=f&aqi=g-v5&aql=&gs_sm=e&gs_upl=23l1333l1l1599l12l8l0l0l0l5l278l1344l0.7.1l8l0&bav=on.2,or.r_gc.r_pw.&fp=74e371c96a48f4b&biw=1024&bih=649

• Can not connect - when entering a password message "the service user profile service has no logon. Failed to load profile \User' cannot access start menu to apply the options.

  Can not connect - when entering a password message "the service user profile service has no logon. Failed to load profile \User' cannot access start menu to apply the options.

  Hello

  1st thing to try is the system in safe mode restore to before the problem

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not solve it read more

  read the tutorial below

  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  When you log on a Windows Vista-based or a Windows 7 computer by using a temporary profile, you receive the following error message:

  The user profile Service has not logon. User profile cannot be loaded.

  http://support.Microsoft.com/kb/947215#letmefixit

  Your user profile was not loaded correctly! You have been logged on with a temporary profile.

  http://support.Microsoft.com/kb/947242

  If you tried to log on to Windows and received an error message telling you that your user profile is damaged, you can try to fix it. You will need to create a new profile and then copy the files from the existing to the new profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• ESXi host does not have the full connection due to an incorrect user name or password.

  Hello

  I need to provide the username and password while reconnecting Esxi host, but with the lines below, I can't succeed. Help, please.

  Game-VMHost-connected state - VMHost 10.50.56.151,10.50.56.65,10.50.56.107,10.50.56.168 | Game-VMHostAuthentication - root username - password "trustno1" - $false JoinDomain

  Thanks LucD., however, I tested is the only way to connect back the vmhost to vcenter. I have not found any cmdlet.

• ESXi host does not synchronize with NTP - causes HA config failures?

  Hello

  We are currently implementing some Cisco UCS systems. We using blades Cisco UCS B200 M1 (x 5670, 48 GB of RAM)

  Everything seems to work fine except these little things, which seems to be related.

  1 NTP synchronization is not happenning, or happening very slowly.

  2. a 10 cluster host, when it is configured for HA, has many guests who fail to be configured for HA (for example we had only 2 guests get properly configured for HA out of 10).

  Initially, I thought REP 1 and 2 were not related, but then I remember reading somewhere that the ESXi host must have simultaneously for HA to work.

  On question No. 1:

  10 guests have a difference of 5-6 minutes between them. Curiously, the first hosts that are connected to a HA cluster, if their duration is similar, they wil work.

  But others are more than 1 to 2 minutes off, they will fail. Our NTP is configured on 2 internal NTP servers, which syncs with the outside world - the 2

  NTP servers are:

  The default gateway of each ESXi

  The network Core switch

  We know that the NTP servers work correctly because our advertising is synchronized with them and we checked on our domain controller local time main external time source.

  Debug information

  Output of /etc/ntp.conf

  ~ # cat /etc/ntp.conf
  restrict default kod nomodify notrap nopeer
  restrict the 127.0.0.1
  Server 10.*
  Server 10.*
  driftfile /etc/ntp.drift

  Everything has been configured through the GUI, I show the output of ntp.conf for confirmation.

  We tried to restart the hosts (without success).

  Everyone knows what we can do to solve this?

  Thank you

  Ionut

  You tried to restart NTP.

• Host does not connect to all iSCSI targets

  Hello

  We use the IBM DS3524 SAN of s/w iSCSI initiator, and we have a weird problem.

  First of all, we had 2 guests and recently set up a third.

  From the beginning, our 2 original hosts had connection to 4 targets, using SRM.

  With the third host it didn't connect to all 4 but only 2-3 boot at startup.

  After the upgrade of all hosts to ESXi 5.0 U1 each host connects only to 2 targets.

  Trying to ping from the hosts, only 2 targets are accessible, those he uses.

  What seems to be is what port group is used, these targets are available and hosts use different paths, work if all the paths.

  A port binding is 'Last active' and 'unused '.

  Am I total evil that all hosts must have 4 connected, but passive targets 2, 2 active?

  I'm afraid that the redundancy is compromised when having only 2 targets connected on 4.

  Setting the configuration-screenshots.

  I already talked to the support of IBM who checked the configuration and log files from the SAN and saw no problem there.

  

  

  

  

  I think that you shouldn't have two interfaces of vmk on the same subnet. Configure a different subnet for vmk1 and configure 2 of your 4 targets accordingly. This should solve the problem.

• How to connect two ESXi hosts with a connection to 1Gbps via ADJUSTABLE and the transfer of files between them?

  Dear community,

  Like many of you, I am facing the problem of executing an effective backup of VMs. unfortunately I can't use standard methods: my servers are rented from the root servers and therefore haver some limits. Their main NIC is connected to the Internet on the speed of 100 MB. It's very slow, if I try to VM backup via this connection images. In addition, backup sessions running through the shared management interface are affecting the production of virtual machine performance.

  To resolve this problem, I ordered an additional network card to each server and asked the data center to connect my themwith a physical link (crossover cable). OK, between my servers 1Gbit link is established, but how do you use now?

  -I can not move the management interface of these cards, because they have no connection to the internet.

  -I can't use among the guest computers because the guest computer is unable to access the files on disk on the host computer.

  So, I've exhausted all my ideas. Maybe someone knows the trick that will let me use 1 GB link between two machines of ESXi to mutually backup disks of virtual machines from one host to another.

  Thanks in advance for your ideas.

  Who is King

  Anton

  Create a vSwitch on each host and set the NETWORK adapter that you will use with the x-over cable.

  Create a portgroup Console of service on each vSwitch and assign it an IP address on the same subnet for each server (router/gateway address does not necessary) for example 192.168.0.1 and 192.168.0.2 on each host.

  Connect the cables between the server network cards.

  You should have a link between two service consoles. I now download and deploy the device of the vMA, on the two hosts for the fault tolerance. Write a script on the VMAs on each host to a-i vmkfstools from one host to another and vice versa.

  If you have virtual machines registered pointing these VMDK on both hosts, then have your scripts remove the VMDK and re - the clone using vmfkstools whenever you back up, you should have a backup solution of rudimentary virtual machine (full copy) in place.

  Now you do not miss the service console?

  Good luck

  Alex

  www.phdvirtual.com

• My computer does not connect to facebook, it keeps displaying the message "a connection expires", how fix this?

  Whenever I try to access facebook.com, I get a message telling me that there was a problem loading the page, the connection has expires. This only happens with facebook. How can I fix?

  Hello

  Thanks for posting your query in Microsoft Community!

  I see that you are facing problems accessing Facebook.

  Do not worry! We're here to help.

  Quick questions:

  1. which version of Internet browser are you using to access Facebook?

  2 is the issue limited to Facebook?

  3 did you changes to the computer before the show?

  4. What is the full error message?

  Come back with more information so that we can help you better.

  If you are using Internet Explorer Please refer to these methods and check:

  Method 1:

  Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the in the Windows registry: http://windows.microsoft.com/en-us/windows7/Back-up-the-registry

  You can try the steps from the following link and check if it works:

  Internet Explorer error "connection timed out" when server does not

  http://support.Microsoft.com/kb/181050

  Method 2:

  You can try to optimize Internet Explorer and check to see if that fixes the problem.

  See this link for more information.

  How to optimize Internet Explorer
  
  http://Windows.Microsoft.com/en-us/Windows/help/Internet-Explorer/slow-five-tips-to-boost-performance
  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  I hope that helps!

  Come back with more information so that we can help you better.

  If the problem persists, or you need help with Windows, please keep us informed.

  We are to help you.

• ESXi host does not recognize DVD-ROM USB

  The server we use as our ESXi server has no cdrom drive.  We connected to a dvd - rom usb to the server drive, but when we try to add to a virtual server, we get a message saying:

  

  Do we do anything to the server so that it recognizes the USB is attached?

  I have attached a 60 day trial that you can use.

  It appear another issue however.  We have two pieces of software running on physical hardware that use "license dongles."  These dongles hold some informaton for the software licenses and are necessary for the software to work.  How can we virtualize these servers if we permanently attached dongles?

  Are these USB dongles?

  4.1 ESXi/ESX and ESXi 5.0 supports USB device passthrough for a host ESX ESXi on a virtual machine.

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1022290

• Windows Vista does not connect me to my profile to the user even after put my password

  My laptop turns off to be in an idle state for an hour... it is ususally. I am generally able to reboot my laptop, but this time, at the start of Windows Vista enabled me to connect to my user profile. I typed my password correctly and countless times and it is not always connect. I tried to connect through the admin prfile and he has not yet let me ride. Safe Mode boot made no difference because I need to access my files. How can it be solved soon? !!!

  Maybe the Startup Repair tool would help:

  Repair Windows Vista using Startup Repair - http://www.bleepingcomputer.com/tutorials/tutorial148.html MS - MVP - Elephant Boy computers - Don ' t Panic!

• HP envy 15t: HP envy 15t laptop does not turn even after going through all the recovery solutions, I've seen online.

  My notebook of HP envy turn not, I plugged in the charger and the indicator showed a white light for a few seconds before changing to an orange light. Let charge for a long time and still have the same problem. Please I really need help.

  HI @IdrisOmotee,

  Welcome to the HP Forum!

  Thank you for becoming a member of the HP Forum. It's a place dynamite to get help from the community, to get suggestions and find what has worked for others. Because you have the best experience, here is a link for you to see, if you have concerns: first time here? Learn how to publish and more

  I understand that you can not power on your laptop. When you plugged the adapter AC light was white to turn a few seconds orange.

  What is your specific model of laptop HP 15 t? Computers laptops HP - how can I find my model number, serial number or product?

  You directly to an electrical outlet and do not use a power / surge bar?

  Have you tried a different outlet?

  Here is a link that may help:HP laptops - tests and using the adapter

  Please let me know the results.

  To express the gratitude of my post please click on the "Thumbs Up Icon'." "  If my post the problem that you are experiencing, please click 'accept as Solution' to help others find what worked for you!

• my hp laserjet 1300 printer does not print more using my iMac with the latest OS

  Since the upgrade to the latest version of the OS (10.11.4) software my hp laser jet won't print more

  Try resetting the printing system reset printing on your Mac - Apple Support System

• Since the update to the current version (6.0.2?), firefox does not connect, but won't that until the ' topic: House "or opens a website. What is missing?

  All firefox windows only opened a "subject: home ' tab, and when I type a URL by hand, I get only a homepage Mozilla Firefox, nothing else. I tried to disable Avast, still no good. Chrome, IE both work very well.

  You are welcome.

  It is generally easier to remove all existing permissions for Firefox.
  
  Then the firewall you'll be asked again the next time you start Firefox.