EX90 clock on bottom of touch controller

Similar Questions

• Codec C40 - remote control / Touch Controller [a]

  Hi all Experts TP,

  I just bought a C40 and put in place. I have the "remote control" and "tactile controller", that are put in place normally and can

  particularly well-run.

  But who cannot work together, this means I plugged the 'remote control', then the controller 'touch' cannot be used and I plugged the controller 'Touch', then the 'remote control' cannot be used.

  I can only use one or the other controls?

  Hi Fai CHi,

  Yes, you can use a single device at a time.

  Best regards, Ahmad

• Jet 7 Tablet 5709: HP Jet 7 touch screen does not work in Windows even if it works in the BIOS menu advanced starup

  Less than two months ago, I upgraded my HP Jet Windows 7 to 10. Over time some questions popped up (random apps that could not be opened, etc.) so I decided to do a full reset, deleting the files from the user. Once the 'install' process is complete he brought me to the initial configuration for Windows 10 screen, asking me my keyboard and language preference. He would not accept any contact entry. I rebooted it and he went to the advanced configuration where I could use the touch screen to do a complete reset. That has not changed anything. I found the info on the HP website and did a reset of the BIOS. That has not changed anything. I got an OTG cable, but was not able to get a keyboard work. I did, however, get a mouse works and has managed to create a new user and login. However, the touchscreen does not work in Windows. I was able to get into the settings and looked at the Device Manager settings. There was only a mouse driver listed under Human Interface. I also noticed a number of question marks in the subtopic of the processor drivers.

  I was able to use the OTG cable to try to re - install Windows 10 from a USB key. When a similar initial settings (language, keyboard) screen broke, I couldn't use the touchscreen. Later, I created a USB with Windows 8.1 thinking he might have a better chance. The same problem. He does not touch inputs. And with a key USB installed via the OTG cable, I can't launch a mouse at the same time.

  It is strange that I have not the problem in the BIOS or advanced startup options. It seems that there is a corruption somewhere, but how do I fix?

  Hello Moronihah,

  You did a clean install (delete all files and programs) the 2nd time you reinstalled Windows 10?

  That's what you need to do first.

  Then, you have to go to the HP website and install the drivers on your USB.

  Above all, you need to include the Goodix Touch Controller Driver and pilot, allowing Malta G-Sensor.

  HP Software and Driver Downloads

  You're using a hub 4 ports with your OTG cable? Which will allow you to use the mouse, the keyboard and the entire USB drive.

  

• HP Pavilion Notebook - 17-f114: HP Pavilion laptop computer - 17-f114dx (ENERGY STAR) controller SM Bus and USB Driver Windows 7?

  I recently installed Windows 7 on this computer and need some drivers for it. For some reason he dislikes plug me my Dynex wireless mouse. All the drivers I need to install? I installed the graphics driver with Intel. Thank you

  (I have attached the image of all the drivers I need, thanks for helping me)

  Hello:

  Here are the links to the drivers you need in the order the devices appear in your screenshots.

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp68120.exe

  Install the bottom first smbus controller driver and restart.

  This package contains the driver and Intel Chipset Installation Utility for the notebook models and operating systems. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager.

  File name: sp73543.exe

  This package provides the driver for the Intel USB 3.0 controller host for the notebook models and operating systems. The USB 3.0 peripheral driverenables.

  File name: sp67267.exe

  This package provides the HP 3D DriveGuard software (HP ProtectSmart Hard Drive Protection) for the laptop models running a supported operating system. HP 3D DriveGuard software protects the drive hard by parking the heads if cell phone accidentally falls, or is suddenly struck by another object.

  File name: sp71811.exe

• Want TS 17: HP Envy 17 laptop touch functionality in Windows 10 TS

  When in point 8.1 of Windows touch screen worked without problems.  When Windows 10 was initially installed, the touchscreen has been fully functional (scrolling, selection, expansion, scroll to the right to open the center of the action, etc..).

  After the first major update of Windows 10 (KB3081424), which was installed on 06/08/15, the touch screen features are located in many programs of functions/Microsoft Windows.  For example, the center of the action can no longer be opened by sliding to the right side of the screen, the material on the screen can no longer scroll button (the touchpad still works for this function) and function magnifying glass (pinch/expansion) does not work on the touchscreen (it still works on the touchpad).  In Adobe Acrobat DC, when enabled in this program, the touchscreen is functional to scroll through a document.  In different Microsoft programs (for example Outlook; Edge browser, etc.) the touch screen works only to locate the cursor/selection text, but that's it - except that the features of the touch screen to click on something to select are fully functional in all situations.

  The day after the installation of the update of Windows 10 KB3081424 an update has been installed for the touchscreen controller (update of the screen USB touch controller eGalaxy A80F-), but it has no effect on the functionality of the touch screen.  Since then, the next Windows 10 major update (KB3081436) was installed on 8/11 having no impact.

  How to restore the touch feature complete.

  @EdB216,

  Hello and thanks for the display on the HP support forum.  What you can do at this point that there are several updates released by microsoft and hardware vendors is running the Windows Update Troubleshooter.

  If this fails to solve the problem.  The only option will be to restore the operating system to the previous, until HP gets the drivers so that they can release them on the support page for your laptop for Windows 10.

  Thanks again for posting and have a great day.

   

• Using the remote control in parallel and touch screen.

  Hello.

  Cisco TelePresence SX20 with firmware TC7.1.4.908e4a9 and has been synchronized with the touch screen. Can I use remote control when the touch screen is activated. Now the remote control is locked.

  Thank you to.

  Hello

  N ° when a codec is associated with a touch controller, it is not possible to use the remote control.

  You question No. 677 in link below

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/articles_doc/telepresence_endpoints_knowledge_base_articles.PDF

  BR Oleksandr

• My Iphone 6 having problems...

  My phone gray active wifi and doesn't appear when I restart the phone sometimes lights up, and when it connects to an available wifi it hangs until I have perform a hard reset and it turns grey new... don't know why the fact that all the advice I saw on google for iphone 4S and not 6... as mine comes on sometimes when I reset the phone and hangs until I have reset... it never did that before I bought a new screen and there was no answer keys so I opened it to position it correctly then he started it... also do not really know it your iphone case 6a drilled holes as a result of the fall of a brainstorming does have anything to do with the screen until what you press tight to the top of the phone does not... having problems with my phone presses keys on that sometimes have that I have to open it and touch the cable attached to the screen, then he returned it itself... don't really know why it comes to the fourth screen changes same result... don't know if change (back box) case resolves it... any help pls

  Your device's problems with Touch controller IC or see so best method is the upgrade to a new device making screen replacement is too expensive & Apple will not support you on this device because it has been repaired by an unauthorized person

• A capacitive touchscreen can be replaced by a screen resistive touchscreen?

  Can we replace the capacitive touch controller or is it fixed?

  Can you please provide more detail?
  What device do you mean?

• Behavior strange cursor Lenovo Flex 15

  Hi all

  I bought a Lenovo Flex 15 and it downgraded to Windows 7. Everything works like a charm, except that sometimes the cursor starts moving on its own at the top left of the screen where the "computer" and "My documents" folders and it starts to open up to them.

  This behavior occurs randomly... do you know what is the cause?

  Thanks for the help.

  Atom

  If you have disabled the touch controller, the jump stop. However, this isn't really a solution.

  Try to wipe the edges of the laptop with a Microfiber cloth. It should improve it a little.

• Spectrum HP convertible x 360: active pen for spectrum 360 15 x

  is there an active pen from the 15 of spectrum?

  Thank you very much

  under support, software & drivers, spectrum x 360 15 t, firmware:

  http://support.HP.com/us-en/drivers/selfservice/HP-spectre-15-ap000-x360-convertible-PC/9256669/model/10193271#Z7_3054ICK0K8UDA0AQC11TA930O2

  HP titled Touch Controller Firmware Uupdate, 1.00, A, 1 Rev.A

  Another publication said to extract the executable files (I used winrar, it used 7 - zip; I think that any zip application can do), then run the bat file.  Works now!

  I find the Dell pen much more responsive than the HP pen.

• My mouse pointer moves in the opposite direction, I intend when I use the touchpad on my laptop. It works fine when I use my docking station and external mouse. How can I fix it?

  I'm using Windows Vista with a Sony Vaio laptop.  At the office, I have a docking station with keyboard and external mouse.  Everything works fine with this Setup.  But when I unplug the docking station and use the touchpad on the laptop, my mouse pointer moves in the opposite direction, that is my intention.  I move my finger and the pointer down.  I move to the right and the pointer goes left.  How can I fix?

  Go to start /Control Panel, and then double-click the icon '' mouse. '' When this window opens, select the tab "Touch Pad" at the top. There's a box near the bottom called "Touch sensitivity", click on that. Change the settings a little bit lower than what they are currently at.

• Distance of the compatibility of MXP for the EX series

  HY guys,.

  I would like to ask something about the compatibility of the remote in the 1700 MXP for Ex90.

  can be used TRC4 distance EX 90? because I got the replacement of equipment for MXP1700 with EX90, but there is no touch screen remote control for EX pack.

  Thank you & Gbu,

  Better subject.

  Nanda

  Hi, thanks for the thanks.

  I had a 1700 at some point as well. If you liked that, you'll love the EX90! :-)

  Especially with the touchpad, you won't miss the remote anymore, but at least for now he

  could be a workaround, please check that you use TC6, I think TC4/5 might not work with the remote control.

  Be sure to check the documentation:

  http://www.Cisco.com/en/us/products/ps11327/products_user_guide_list.html

  Nanda, if you can evaluate the responses we made (using the stars below each assignment), and then assign the thred responded if it is.

  How to: useful frequency responses and identify useful or correct answers.

• Degraded RAID 1 array: PowerEdge 2800

  Hello to everyone. I hope someone can shed some light on this unusual situation.

  I have a PowerEdge 2800, which must be replaced before May this year, this is a great server and done an excellent job over the past 7 years.

  OK for the problem; The server administrator has been a failure on 0:0

  In the server, we have:

  0: Maxtor 36 GB 15 k 0 0:1 Fujitsu 73 GB 15 k something 1:2... 1:3 something...

  So, I jumped 0:0 and the server worked great with a range of gradations, and 15 seconds I inserted back to the PE2800. After about 45 minutes the RAID 1 array has been rebuilt, but it still says expected failure. So I thought that better order some new readers - I received today; 2 x 146 GB 15 k Seagate Cheetah.

  OK, so I jumped 0:0 drive and inserted one of the 146 GB Cheetah and the server crashed - wouldn't boot at all and gave me an error stating that the logical drive failed.

  Thus, in the PERC4i BIOS, I forced drive 0:1 online and the server is now back operational but with a range of gradations.

  So that's where I am, what choice do I have?

  Insert the old disk with a predicted failure, leave it alone or try the 146 GB Cheetah. I don't really want to do an any of them, but I will order another 73 GB Fujitsu in the meantime.

  I want to know is why the server crash after having inserted the cheetah disc? I traded to many-a-time pluggable hard drives in the past in several dell breaks and never experienced anything like this.

  Degraded running, any response would be massively appreciated.

  Thank you very much.

  "So, I'm now to square, where I have a RAID1 system with a disk failure planned.  What would you do from here on? »

  Another thing that many people do not know is with a disk of pf, should it be forced offline before replacing, if not the FP flag can be assigned to the new drive (until a real "rescan" is performed) and can result in strange behavior (the controller is more sensitive to potential readers of pf failure).

  "Common sense says I can't mix-match 10 k / 15 k TPM!

  You CAN / layout speeds and/or sizes (there's nothing wrong with him "technically"), but in real-world scenarios, you would ever want to mix speeds (depending on the configuration, it degrade the speed of the whole picture).  One thing you can't do is mix U320 SCSI U160 readers on a bottom of basket/controller.

  "What would you do from here on?

  I guess from here depends on what you feel more comfortable making.  There is a chance that the pf reader works fine until you are finished with the server (or until you can get another replacement - if you feel another replacement would be better than those you currently have), even if it might cause additional problems if his condition deteriorates.  There is a chance it could happen again if you try to replace it, but I think it's unlikely to happen.  If it was me (and it is important to remember that this isn't :)), I force disk 0 offline and replace "hot" by the other 146 GB drive.  Another thing you could do, who feel probably less risky, is simply to insert the disc of 146 GB in an open slot, assign as a relief, then force offline disk 0, which results in a regeneration start automatically with disk 0.

• Toshiba 32AV615DB reduce while watching her without touching the controller

  Hello.

  My TV acts as if there is a sign to extra distance.
  While watching, the sound will reduce without touching the controller.

  It is not possible to market. It will scroll together various displays.
  Buttons on the side of the TV do not work.

  You can activate the TV market, sometimes who will work for a while!
  Another day, it will work perfectly.

  Any suggestion is welcome.
  Thank you

  I found a thread that describes a very similar TV acoustic behavior:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=70847

  It seems that the Dynamic Volume is enabled in the settings of your TV.

  + Audyssey Dynamic volume® control volume levels in order to eliminate the strong points and lift the soft dialogue for film and television more enjoyable viewing. +
  + In the sound menu, press up or down to select Dynamic Volume. +
  + Press left or right to select On or off.

  Check it out. Maybe it helps.

• How to move the "blue bar" with the start option and the clock and icons of a vertical__position on the left side of the screen to the bottom of the screen... has this before happen__once, can't remember what to do.

  How can I move the 'blue bar' with the start option and the clock and icons on the left side of the screen to the bottom of the screen.  It's happened before and I forgot how to move.

  Hello pookprec

  Here's how to do it

  .