Example Configuration (INI) playback

Similar Questions

• Example configuration for the TACCAS + ASA 8.22

  I'm looking for an example configuration to TACCAS + on 5.2 ACS with an ASA 8.2.2.

  Any help would be appreciated.

  I think the following should about do - but it is MUCH easier to do this in the GUI

  AAA-server protocol Ganymede GANYMEDE +.
  x.x.x.x host AAA-server GANYMEDE (management) key *.
  GANYMEDE LOCAL console for AAA of http authentication
  authentication AAA ssh console LOCAL GANYMEDE
  AAA authentication serial console LOCAL GANYMEDE
  Console to enable AAA authentication RADIUS LOCAL
  Console Telnet AAA authentication RADIUS LOCAL
  AAA accounting ssh console GANYMEDE
  Console Telnet accounting AAA GANYMEDE
  AAA accounting serial console GANYMEDE
  AAA accounting enable console GANYMEDE
  GANYMEDE AAA accounting command

  Remember that you must create the network device in ACS with the same shared key.

  Paul

• Number of serial port configuration ini file!

  Hello guys,.

  I am creating an ini config file to save the selected serial port of VISA.

  I will adapt if the ini file doesn't exist then look to pc serial ports and choose one of them. If the file is read the value to use when I use data acquisition.

  In the example attached. I have a structure of event (such as my application), where I have a stocking to open the 'options '. If you open the main vi and pass the error, open the Subvi options and choose comport, if you click on 'ok' it save the ini file, if you click on "Cancel" it closes and show in the indicator of the value of the comport the .ini file. The Subvi works well.

  The problem is when I try to read the value of include an application start. I put the code but that's fake.

  I used "simple saving and loading control values" TST ( https://decibel.ni.com/content/docs/DOC-15349 ) and it works well for the control of the Sub - VI.

  Why I got error and I can not read ini value?... section and the key is correct. I can't find the problem.

  Concerning

  Fred.

  OpenG INI example explained on the-openg-vis-that-i-couldn't-live-without

• Error of TNA: 47077 TNA configuration .ini file is not found

  Hi all

  I just installed 11.1.1.7 on my 64-bit windows OBIEE. And tries to install OLIVIER 7.9.6.4 on top of that. When installing, I get an error:

  Error of TNA: 47077 file Config.ini TNA has not been found. Make sure that your environment is configured correctly.

  Pleasw help me guys... I'm new to this facility OBIA.

  It's a BUG

  See this BI Applications on EE BI 11.1.1.7.0 7.9.6.4 installation (Doc ID 1561846.1)

  Please to the bottom of the attachment Technote1561846.1_InstallSecurity.zip and apply the solution.

• T440p utility ThinkPad Configuration Capture/playback settings are missing

  Go to this URL:

  http://support.Lenovo.com/en_US/downloads/detail.page?docid=DS037579

  This is the driver for T 440p

  and chose the BIOS strings the

  Quote:

  Utility to Capture/read configuration of installation for Windows (SRSETUPWIN) for Windows 8.1 ThinkPad (32 bit, 64 bit), Windows 8 (32 bit, 64 bit), Windows 7 (32 bit, 64 bit), XP - ThinkPad

  Download driver is not included.

  the

  http://download.Lenovo.com/ibmdl/pub/PC/pccbbs/mobiles/n10ts02w.zip

  are missing.

  Please fix.

  This should be fixed now.

• Example of current playback

  Hello

  I was wondering if there are examples on how to use now playing with the media player?

  As I would like to be able to use the play / pause button on the side of the unit to stop and play the audio in my application and I also had that to be able to show what the user listen to by adding it to their BBM - is this possible with now playing or I have to do something with BBM as well?

  Thank you

  There is a sample BlackBerry application that does just that:
  https://github.com/BlackBerry/Cascades-samples/tree/master/nowplaying

  I have not loaded, but my guess is that it updates automatically BBM listening to field if the user enabled the option 'Show what I'm listening to' in the settings of BBM.

• Guide / blog example configures / has for a new workflow

  I played some time with powercenter to create new workflows. Now, I want to run them in the CAD. But I can not find a guide or a blog (with examples) wich steps to follow to set up the car for a new workflow.
  
  More information about this just a...
  
  TNX in advance...
  
  just found this blog but is way ' at the global level, written t
  
  Published by: user565199 on February 23, 2010 02:26

  If I'm not mistaken, there are information in the user guide DAC with the details step by step on the registration of new workflows in DAC. Check only once.

• Site VPN to IPsec with PAT through the tunnel configuration example

  Hello

  as I read a lot about vpn connections site-2-site
  and pass by PAT through it I still haven't found an example configuration for it on e ASA 55xx.

  now, I got suite facility with two locations A and B.

  192.168.0.0/24 Site has - ipsec - Site B 192.168.200.0/24
  172.16.16.0/24 Site has

  ---------------------------------------------------------------------------

  Host--> participated in IP 192.168.0.4: 192.168.0.3-> to 192.168.200.20
  Host 192.168.0.127--> participated in IP: 192.168.0.3-> to 192.168.200.20
  Host 192.168.0.129--> participated in IP: 192.168.0.3-> to 192.168.200.20
  Host 192.168.0.253--> participated in IP: 192.168.0.3-> to 192.168.200.20

  Host 172.16.16.127--> participated in IP: 192.168.0.3-> to 192.168.200.20
  Host 172.16.16.253--> participated in IP: 192.168.0.3-> to 192.168.200.20

  ---------------------------------------------------------------------------

  Now that I have guests autour within networks 172.16.16.0 like 192.168.0.0,
  witch need to access a server terminal server on the SITE b.

  As I have no influence on where and when guests pop up in my Site.
  I would like to hide them behind a single ip address to SITE B.

  If in the event that a new hosts need access, or old hosts can be deleted,
  its as simple as the ACL or conviniently inlet remove the object from the network.

  so I guess that the acl looks like this:

  ---------------------------------------------------------------------------

  access VPN-PARTICIPATED-HOSTS list allow ip 192.168.0.4 host 192.168.200.20
  VPN-PARTICIPATED-HOSTS access list permit ip host 192.168.0.127 192.168.200.20
  VPN-PARTICIPATED-HOSTS access list permit ip host 192.168.0.129 192.168.200.20
  access VPN-PARTICIPATED-HOSTS list allow ip 192.168.0.253 host 192.168.200.20
  VPN-PARTICIPATED-HOSTS access list permit ip host 172.16.16.127 192.168.200.20
  VPN-PARTICIPATED-HOSTS access list permit ip host 172.16.16.253 192.168.200.20

  ---------------------------------------------------------------------------

  But, now, my big question is, how do I said the asa to use: 192.168.0.3 as the
  address for the translation of PAT?

  something like this he will say, it must be treated according to the policy:

  NAT (1-access VPN INVOLVED-HOST internal list)

  Now how do I do that?
  The rest of the config, I guess that will be quite normal as follows:

  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set of AA peers. ABM CC. DD
  card crypto outside_map 1 set of transformation-ESP-AES-256-SHA
  outside_map card crypto 1 lifetime of security set association, 3600 seconds

  permit access list extended ip 192.168.0.3 outside_1_cryptomap host 192.168.200.20

  ---------------------------------------------------------------------------

  On SITE B

  the config is pretty simple:

  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set of peer SITE has IP
  card crypto outside_map 1 set of transformation-ESP-AES-256-SHA
  outside_map card crypto 1 lifetime of security set association, 3600 seconds

  outside_1_cryptomap list extended access allowed host host 192.168.200.20 IP 192.168.0.3

  inside_nat0_outbound list extended access allowed host host 192.168.200.20 IP 192.168.0.3

  ---------------------------------------------------------------------------

  Thank you for you're extra eyes and precious time!

  Colin

  You want to PAT the traffic that goes through the tunnel?

  list of access allowed PAT ip 192.168.0.0 255.255.255.0 192.168.200.0 255.255.255.0

  PAT 172.16.16.0 permit ip access list 255.255.255.0 192.168.200.0 255.255.255.0

  NAT (inside) 1 access list PAT

  Global (outside) 1 192.168.0.3 255.255.255.255

  Then, the VPN ACL applied to the card encryption:

  list of access allowed vpn host ip 192.168.0.3 192.168.200.0 255.255.255.0

  Thus, all traffic from Site A will be PATed when you remotely 192.168.200.0/24

  The interesting thing is that traffic can only be activated from your end.

  The remote end cannot initialize traffic to 192.168.0.3 if there is not a version of dynamic translation on your side.

  Is that what you are looking for?

  Federico.

• Paths of reading via the Config Ini file

  I was curious to know how one send or read from a configuration (.ini) file paths in LabVIEW. Any help is appreciated especially examples

  It's actually pretty simple...

  

• Help to configure content vRealize Pack of Operations Manager for paper Insight

  I am running the following:

  vrops Version 6.0.1.2523163

  Log insight Version 2.5.0 - 2629935

  I installed the v1.0 vROps 6.x content pack in Insight Journal and used this article very useful when configuring the liagent.ini file

  vRealize content Operations Manager Pack for newspaper Insight - VMware Blogs

  Everything seemed to go well, but the end result is no data of vrops Li and connection errors in the newspapers of the agent without clear indication of why it is not agent connection.

  Viewing the log file, I see a lot of counters indicating the date, the agent of time shows that he has worked for a few days now with more 8 million observed events.

  However, interrupted events number matches the 8 million observed number of events which means that everything has been ignored "due to the overflow of local storage or rejected by the server" as stated in the article.

  2015-08-23 17:07:16.704273 0x00007f770ffff700 < path > CFApiTransport:348 | Re-login to the server vrops.domain.local:9000

  2015-08-23 17:07:16.762633 0x00007f770ffff700 < error > CurlConnection:482 | Transport CurlConnection::Config error: could not connect to the server

  2015-08-23 17:07:16.762664 0x00007f770ffff700 < path > CFApiTransport:328 | DoConnectJob [deferred by 167 dry connection]

  Agent of the time 134:15:34.106000

  Events observed: 8 176 438 (total number of events saw the newspaper sources since the Agent started or changed server)

  The events collected: 0 (= fall the observed)

  Events sent: 0 (delivered to the destination server)

  Events ignored: 8 176 438 (abandoned due to overflow of local storage or rejected by the server)

  Mailing frequency: 0.00 EPS (average of the last minute)

  DB file size: 143,576,064 bytes

  CPU usage: 0% (in the last 900 seconds average)

  Link: cfapi://vrops.domain.local:9000

  Host name (FQDN full): vrops.domain.local

  Opportunity of free space: 191,429,376 bytes

  Two things, I thought maybe to blame that I don't know how to fix:

  1. vmw_vr_ops_hostname = IP address? same as address of node? My cluster shows the node address as the IP address rather than a FULL domain name. I tried to provide as well in the ini file, but doesn't seem to help, but I find it weird that I don't see the name domain FULL configuration section that I linked to suggested that I should. And what is listed here would be that I filled in the ini file to vmw_vr_ops_hostname file?
  2. In vrops, under Administration > Support > newspapers > change the Logger Configuration > export to Syslog, no matter how many times I uncheck the box 'exit of syslog server logs' external and click ok the box remains checked off the coast. I'm sure that this must be unchecked, but even if it were problems, as I understand it, it would be especially causing duplicate rather logs that prevent all newspapers to appear as is my case.

  According to this article it is said: "If export syslog is configured then the required configuration of the specific agent is not set and the syslog Protocol is used instead of the cfapi." It is also very important to note that configurations can and will be replaced! By example, if you configure the agent works with the content pack (for example. liagent.ini) client-side and later someone configure syslog export from the user interface, the configuration of the client-side agent are crushed with the parameters of the interface user break the integration of content package. »

  vRealize content Operations Manager Pack for newspaper Insight - SFlanders.net

  Given that syslog export was apparently when I first tried to set this up, it would make sense that this is what causes problems, but how could I then set? Especially when the user interface won't let not disable me export syslog on vrops?

  Any help is appreciated. Thank you

  Very useful - I think that the problem is with the [server] section if your configuration. What is the host name = value? It can be solved? The reconnecting log messages are expected that the delayed connection makes it sound like the configuration of the host name does not.

• problem reading DAQmx using Measurement Studio 2010 (even with examples OR)

  Hi all

  I'm reading the voltage using a map of NOR-DAQ-6211 with Measurement Studio 2010 SP1 V9.1.0.204. using Visual Basic .net 2010.
  When I create the task of data acquisition with the measurement studio Wizard, (Assistant DAQ) everything works fine. However, when I try to create my own task player in looking over the "ContAcqVoltageSamples_IntClk" everything I read is a value in the range of Vmin to Vmax (or to Vmin Vmax) and then she stays there no matter if I change my diet. Vmin and Vmax does not yet match my values of voltage. (It acts like that on my application and example of OR) I guess I missed a few initial settings. The config of AIChannel in two projects (manual task and Augo-Gen) use AIChannelConfig.RSE (I tried other options, but no luck).

  The only wiered thing is that when I open examples of projects, VS does not recognize the object references of NOR. Workspace names DAQmx. When I check the references, it shows that it does not find the reference to NI.Common. To make it work/compilation, removed from the solution and I again added. (I don't think this is related, as it seems that there are available tensions but not read correctly).

  The other thing is that my input voltage is 3 or 0 volt. When you use the manual DAQtask, when I toggle the voltage, the values displayed change momentarily the order of 0.001 Volts and then go back to their previous values of Vmax and Vmin.

  Is there more information I can provide?

  Help, please
  Thank you

  Yay! I just solved my problem,

  From the first moment I knew there was something fishy about this AITerminalConfig thingy! I made two errors:

  1. in the code example Configuration AI is encoded: CType (-1, AITerminalConfiguration) that caused the code example does not work for all channels to HAVE it

  2 - also, I have in my code, I had put this config to the correct value, but I was checking ai0 all the time while the signal was on another I. I was under the impression that since the example does not work for all my channels, then probably my code does not work as well.

  If after changing the line in the example for the correct terminal configuration settings, he began working for the AI number I was looking for too much and I found that my code worked for my AI # correctly from the beginning. I wasn't just to see it!

• SFE2000 configuration Layer 3

  Hello world. I have a SFE2000 switch and I want to do the following:

  (1) setup 2 VLANS, one on the port 1 (172.20.73.x), the second on port 5 (172.20.74.x), the remaining ports on the default VLAN (172.20.72.x)

  (2) enable Layer 3 mode and have all the VLAN route between them

  So far I have the VLANs set up and assigned to the correct ports, I activated the mode layer 3 through the console serial port. I'm not sure what to do from here, or how to set up routing. Provided by linksys manuals are not very useful.

  I do not have a SFE, but you need to configure IP addresses for the switch in each VLAN. If the online reference guide is correct, it should be on the ip interface page (System > System Management > IP addressing > IP Interface).

  For example, configure you the IP 172.20.73.1, 255.255.255.0 on VLAN 10 (if it's the VLAN on port 1).
  Configure you the IP 255.255.255.0 on VLAN 20, 172.20.74.1 (if it's the VLAN on port 5).
  Configure you the IP 172.20.72.1, 255.255.255.0 on VLAN 1 (if it's the VLAN by default/management).

  All VLAN 10 devices must use the default gateway 172.20.73.1 in their IP configuration (static or assigned by a DHCP server, you have put in place).
  All VLAN 20 devices must use the default gateway 172.20.74.1 in their IP configuration (dito).
  All devices in VLAN 1 must use the default gateway 172.20.72.1 in their IP configuration.

  I think that, by default, the ESF should route all traffic between these subnets. If you want to limit traffic routing between subnets you will need to set up filtering rules.

• Configuration of 2 digital circuits in a voice GW

  Hello world

  I'm dealing with digital configuration 2 lines ina unique GW.

  My router is a 2900, and I want to install 2 digital lines in a 2 port T1/E1 MFT VWIC2

  My questions are:

  What do I have to configure Dial peers for the second digital circuit to have redundancy on outgoing calls?

  I've been looking for example configurations like that, but had no luck, and the documentation does not explain this type of scenario.

  My logic is that I have to configure Dial peers again for the second Digital trunk, but then in configuration CUCM how can I allow users to switch automatically? I thought that in the same road group add the second line by specifying the port in "members of the Group current road", but I don't know if this is not correct, or if I should create a new routing group?

  If anyone can help me it will be fully appreciated.

  Yes, you need dial-peer to the two ports, depending on what you want, with the same preference, or not.

  You have no control over the switching/switching of CUCM with H.323, depending on the config of the RFP.

• Cannot configure VWIC-2MFT-T1 on 1841

  I checked and double-checked before you buy and this card is obviously taken in charge on the 1841 for 'data only mode' which is all that I need.  I have 3 T1s multi-links mode and I want to use 2 of these cards (and 3 of the 4 ports) to support.  The problem is that, even if the HS INVENTORY finds the card, I can't spear the command "card type" to indicate I use it with a T1 - I get this:

  R3 (config) #card type t1 1 0

  ^

  Invalid entry % detected at ' ^' marker.

  So I tried to issue the command 'controller T1' and it does not recognize the slot as containing a map T1 (which makes sense since the order of the 'map' did not work).

  I found many references to this map being supported in docs Cisco with a minimum OS around 12.2 (8) - it varies according to the chassis.  I can't find the required explicit OS for the 1841, which is a concern, but I use 12.4 (13r) VERSION SH T. finds "2 channeled T1/PRI ports" which is the card of the MFT.

  Am I missing something? I need to get the interfaces configured on these maps series.  Thank you very much.

  Hello Dale,

  If you use a VWIC-2MFT-T1, you're not supposed to use the 'card-type' for the map command is just a T1. Let's not forget that this command is used if the card has features of T1/E1; for example, if you were installing a VWIC2-2MFT-T1/E1.

  Then, you must configure the T1 controller to view the serial interface, as you can see in the example configuration:

  controller T1 0/1/0

  framing ESF

  linecode b8zs

  slots of channel-group 0 1 - 24

  !

  controller T1 0/1/1

  framing ESF

  linecode b8zs

  slots of channel-group 0 1 - 24

  In this particular case, the card is installed in slot 1 of the WIC. If the card have been installed at location 0, the controller of numbering will be different because the number between slashes will be 0 (Controller t1 0/0/0 or 0/t10/1 controller)

  If these commands are not difference, now, gather the following products:

  • See the version
  • Show diag
  • See the t1 controllers

  Kind regards.

• ASA5505 for configuration VPN Failover ASA-5510

  the best way to configure a second VPN tunnel by another carrier, to fail.  The two tunnels would go to the same network a Remote Site.   Is it possible to apply a metric or monitor the tunnel so that if the choice we're unavailable two choice would resume.   Can you point me to the example configuration preferably with ADSM?

  Hi Stewart,

  Please visit this link for the same thing:

  https://supportforums.Cisco.com/blog/150001

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.