eyeball and eyeblink controlled robot with prevention system of barriers for people with disabilities

Similar Questions

• How guys do you overcome (Mac Book and iMac) screen sizes with disabilities when creating scrolling effects, can work the same on both screens when you started with the iMac?

  How guys do you overcome (Mac Book and iMac) screen sizes with disabilities when creating scrolling effects, can work the same on both screens when you started with the iMac?

  Technically, since it's the same effect with the same settings, it works on both sizes. However, you need to test both is to decide if it will appear visually correct on both screens or not. On screens more wider/taller objects can appear earlier on the screen, it is advised to test again on both screens.

  See you soon,.

  Vikas

• I already bought 2 XP Professional pay. Now to buy Windows 7, I still have to pay for my PC and laptop computers. There is a special offer for people like me? Meet _ @_. ___

  I already bought 2 XP Professional pay. Now to buy Windows 7, I still have to pay for my PC and laptop computers. There is a special offer for people like me? Answer to * address email is removed from the privacy *

  Consider the Windows 7 Home Premium Upgrade Family Pack.

• Reset computer to factory settings, installed SP1 and lost control of the keyboard and the mouse. Had to do system restore just before the installation of SP1.

  Original title: help

  OK to reset to factory settings to allow hopefully laptop to read CDs again, then downloaded installed sp1 and lost control of the keyboard and the mouse, and still can not play music not forget hadda restart in safe mode to use the system restore to just installing the sp1 b4

  Hi MartyFenwick,

  I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

  1. What is the brand and model of the computer?

  2. What is the brand and model of the mouse and keyboard?

  3. you receive an error code or message?

  4. is everything works well after running system restore?

  5. what exactly do you mean by "hadda restart in safe mode to use the system restore to just installing the sp1 b4?

  6. what happens when you try to play music CDs?

  7. what program you use to play the CD?

  Please follow the methods and mark the question below:

  Before you install SP1, follow the method 1 and 2.

  Method 1:

  You need to perform a clean boot to prevent any third party conflicting application from interfering with your computer.

  To put the computer in a clean boot state, you must follow the steps in the article mentioned below and check with the question.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: You must follow step 3 of the article mentioned above to recover your computer to a Normal startup after you complete all the steps.

  Method 2:

  I suggest you disable the antivirus for temporarily until the installation of SP 1.

  Disable the antivirus software:
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3:

  Follow the steps in the link for problems with the keyboard and the mouse below.

   
  Mouse, touchpad and keyboard with Windows problems:

  http://Windows.Microsoft.com/en-us/Windows/help/Mouse-touchpad-and-keyboard-problems-in-Windows

  Method 4:

  Follow the steps in the link below.

  Learn how to install Windows Vista Service Pack 1 (SP1):

  http://Windows.Microsoft.com/en-us/Windows-Vista/learn-how-to-install-Windows-Vista-Service-Pack-1-SP1

  I hope that the information above helps you.

• Age of Empires II - "can't initialize graphics system. Make sure that your video card and driver are compatible with DirectDraw.

  Hello

  I have a problem of Age of Empires 2 running on my new computer. Keeps displaying the following error message: "cannot initialize the graphics system. Make sure that your video card and driver are compatible with DirectDraw. "Someone at - it solutions to this? I have already visited many forums and trying different solutions; None of them helped.

  Tried solutions: change the compatibility and as an administrator, switching to 16-bit color, turn off my graphics card, execution of the extension "nostartup" of the game, looking for old patches from Microsoft (which most are now unavailable due to the game being so old). I KNOW that others have been able to get this game to work on the Windows 7 operating system, but with a few other quirks and I KNOW my video card and driver are more than capable of handling this game. Any suggestions?

  System Specs:

  System manufacturer/model number Dell/Studio 540
  Operating system windows 7 home premium 32 bit
  6 GB of memory
  Graphics card ATI Radeon HD 4350
  Monitor (s) displays Reference Dell ST2410

  Thanks in advance,

  EP

  I had the above problem with AOEII:Age of the Kings. My brief spec is Windows 7 Ultimate edition (SP1) and a card nVidia 8600 GT. I did the following (make sure you reboot after each installation):

  Make sure that you are running the latest patch of AOEII:AOK (2. 0 a):

  http://www.Microsoft.com/download/en/details.aspx?ID=35

  Download and install the latest version of DirectX:

  http://www.Microsoft.com/download/en/details.aspx?ID=5264

  Download and install the latest nVidia Driver suite. I left the autodetect my card software and reset all my default settings. I also installed the full software suite:

  http://www.nvidia.com/download/index.aspx?lang=en-us

  Finally, right click on the shortcut of AOE and click Properties. Click on the Compatibility tab and select the following:

  -Run this program in compatibility mode - choose Windows XP Service Pack 2 (!) NOT 3!)
  -Disable visual themes
  -Disable the Composition of the Bureau
  -Run this program as an administrator

  One of the above options maybe work on its own, but that's what I had to do to make it work and I tested it after each step.

  Good luck!

• Age of Empires 2: Age of Kings does not work on Windows 7. The error is: could not initialize graphics system. Make sure that your video card and driver are compatible with DirectDraw.

  I can't get my Age of Empires 2: Age of Kings drive on my computer.

  It gives me the error message: could not initialize graphics system. Make sure that your video card and driver are compatible with DirectDraw.

  What exactly is DirectDraw. and how can I make my video card and the driver compatible to it. I already tried to uninstall and reinstall the drive.

  Help, please!

  What kind of graphics card you have and you have the latest DirectX and video card drivers? If this isn't the case, update them.

• I have a xp system and my friend installed with a password, I can't reach him is there anyway I can get past this issue?

  original title: password, logon problem

  I have a xp system and my friend installed with a password, I can't reach him is there anyway I can get past this issue? I can't even logon to my computer.

  Hello
  Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features. For more information about this policy, please refer to the sticky below.
  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/3eba3150-8742-4264-be9f-0daaad2282cd

• After restarting windows and then no error in config/system is finally windows starts successfully with no problems quo. __

  "windows couldnot start because the following file is missing" c:/windows/system32/config/system.
  This message appears at the first start, but when I press ctrl + Alt + Delete, restart windows and then no error in config/system does finally come windows starts successfully without problem usually. I searched on the internet that all solutions are given if windows XP does not start. But in my case after restart only a single window loads successfully. I'm dubious before using the recovery console.
  Please help everyone,
  no case I found the solution to this particular problem.

  The question was preceded by a loss of power, aborted reboot or abnormal termination? (This includes pulling and buttons power).

  These can cause corruption in the file system that must be fixed before you do anything else. If none of these events occurred (or even if they have not taken place), you must verify the integrity of your file system before anything else (especially "try" things).

  
  Never, never, never start with the support engineer technical 'expert' who are hired by Microsoft to implement the KB307545.  You are likely to be in for a frustrating waste of time and might just make things worse.

  Always, always, always start with a chkdsk with first error correction.

  There is zero logic to start try to copy files to a hard drive with a corrupted file system so corruption of file system must be fixed first using the XP chkdsk program and run chkdsk can solve your problem completely.

  Use the XP Recovery Console to check the file system on your HARD drive and fix the problems and then try to start your system - this may be all you need to do.  Or, you are welcome to just start trying things that might work.

  Start the Recovery Console Windows using an XP bootable installation CD, or create a bootable CD from the Console of the Recovery XP (no XP media required).

  A CD of XP Recovery Console is not the same as the recovery disks that may have come to a store to purchase the system.

  If you have any bootable CD to run the XP Recovery Console or that you are not sure what type of bootable CD you have, can create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

  If you need instructions to create a bootable XP Recovery CD of Console, we can predict that too (just ask).

  After booting into the Recovery Console, you should be in this folder:

  C:\WINDOWS

  For each of your hard disk partitions, you must then run:

  Chkdsk /r

  For example, at the Recovery Console prompt, enter:

  CHKDSK c: /r

  Let chkdsk finish to correct the problems, he could find.  It may take a long time to complete or seem to be 'glued '.  Be patient.  If the HARD drive light flashes, it's something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  The chkdsk/r must be completed without error, you may need to run several times until it does.

  Remove the CD, and then type "exit" to exit the Recovery Console and restart the computer and the report with your progress.

• System Restore does not progress past during initialization and the screen deforms with no other activity

  Downloaded some updates which has increased my hard disk activity, which has me concerned. I went to the restoration of the system to use my laptop for the last restore, point before downloading. And now I have the system questions without error code of restore, hard boots fine except message saying that the system restore did not complete. I'll look forward all help! Thanks in advance!

  Hello

  There are a variety of reasons for system restore problems

  Norton and Norton product Tamper Protection is the main

  Read about it:

  http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20101101224849EN&LN=en_US

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  You can try restoring the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  and malware can interfere with the restoration of the system

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Sound work for system sounds and when I mess with sliding windows mixer

  Literally everything is dead silent including steam, ie8 and my games. With the updated audio drivers and all the sounds on highest

  Hi Michael,

  Thanks for posting your query in Microsoft Community.

  Let me ask you;

  1. Did you change to the computer?
  2. What is steam? What is an application or a program?
  3. How you did update the audio drivers?
  4. What is the brand and model of the computer?

  Let's try the methods below and check.

  Method 1: You can run the troubleshooter from the below mentioned link and check if it can help solve the problem , Open the Audio playback troubleshooting utility

  Method 2: I understand that you tried to update the drivers. However, I try to uninstall and reinstall sound card driver.

  a. Click Start, type Device Manager in the start search box and press ENTER.
  (b) in the Device Manager dialog box, expand of sound, video and game controllers.
  c. find the audio device that was included with the computer.
  d. right click on the device, and then click Properties.
  e. click driver, and then clickUninstall.
  f. make sure the boxremove the driver for this deviceis cleared, and then clickOK.
  g. in the Device Manager dialog box, click the Actionmenu, and then clickfind the hardware changes.

  You receive a message that States that a hardware device is being installed, and then the not installed audio device appears in Device Manager.

  h. close the Device Manager dialog box.

  Method 3: Check if the problem persists in the clean boot state

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  Note: see 'How do I reset the computer to start normally after a boot minimum troubleshooting' to reset the computer starts normally after troubleshooting.

  Method 4: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better. I hope this helps.

  Measures to check the application event log:

  a. click Start.
  (b) in the search box type eventvwr.msc , and then on enter.
  c. now, click Application in the event viewer (local).
  d. now, looking for event log on the right side of the event viewer window.

  You can read the following article:

  Open event viewer

  What are the information in event logs? (Event Viewer)

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• I am a student with a MacBook Pro, and I need a Windows operating system to run software from the school. I can't afford a new ' puter, so I got to BootCamp Windows 7. Where can I get a copy?

  I am a student with a MacBook Pro, and I need a Windows operating system to run software from the school. I can't afford a new ' puter, so I got to BootCamp Windows 7. Where can I get a copy?

  Where can I still get Windows 7?

  Full version - Microsoft Windows 7 Home Premium

  Microsoft Windows 7 Ultimate - full version

  Full version - Microsoft Windows 7 Professional

  Microsoft Store:

  http://www.microsoftstore.com/store/msstore/list/parentCategoryID.44066700/CategoryID.60521000

  http://www.Microsoft.com/student/en-us/products/Windows/default.aspx

  If you're in College, you can also check your Campus for a greatly reduced copy Bookstore.

• Hello. You will need to update Mac OS El Capitan. Currently have v.8 CS Photoshop and Lightroom 2 v.2.4. In order just to work with the new operating system, please inform for updating both.

  Currently have v.8 CS Photoshop and Lightroom 2 v.2.4. In order just to work with the new operating system, please inform for updating both.

  Hi R0w1% 40nd,

  Adobe Photoshop CS v.8 and Lightroom 2 v.2.4. are very old software and the operating system you are using is the most recent, so there may be compatibility issues that adobe has not tested these applications on newer operating systems.

  The installer for Adobe Photoshop CS v.8 and Lightroom 2 v.2.4. are no longer available.

  You can see the creative Cloud, creative cloud and rates membership plans | Adobe Creative Cloud

• Start and stop Virtual Machines with the system

  Hello

  In a server cluster @vcenter HA/DRS 5.1, I enabled start and stop virtual machines with the system option but after I checked two days later, he is off again somehow. What makes this option off? I had a power failure in the datacenter. vCenter server has not been upward. I started all of the ESXi servers manually then went all VMs account is declining. I want that they start automatically when server ESXi upward.

  Thanks in advance,

  Thank you. This option is more valid than if the hosts are part of an HA Cluster license. I suspect that you configured through the traditional vSphere Client and that it is a bug with this client. If you try with the new vSphere Web Client, you will find a notice that it is disabled and there is no button "Edit".

  Concerning

• My Windows 7 Professional Office system disk has been corrupted and I took the opportunity to install a SSD for a new system disk and reinstall Windows.  The system is installed and running on the SSD, with my old drive system currently used for storage a

  My Windows 7 Professional Office system disk has been corrupted and I took the opportunity to install a SSD for a new system disk and reinstall Windows.  The system is in place and running on the SSD, with my old drive system now used for storage as it is still readable.  The only product Adobe, that I reinstalled so far is drive XI but I would like to reinstall items 8 and Acrobat 9 without occupying more licenses that both are also installed on my laptop.  Can you tell me the best way to do it?  -Thank you

  If you have two activations allocated already and one was lost on the hard drive that has failed, then you must contact the Adobe Support via chat and ask them to reset your activations.

  To the link below, click on the still need help? the option in the blue box below and choose the option to chat...

  Serial number and activation support (non - CC) chat
  http://helpx.Adobe.com/x-productkb/global/Service1.html ( http://adobe.ly/1aYjbSC )

• Why can't you have variable conditionalized on template and control them with expressions?

  I have a chapter that is shared between two guides with different titles. On master pages, I inserted the variables for the two titles of books and conditionalized of each variable.

  When I go to the pages of the body, both titles appear in footers. When I apply expressions to control what as I want to appear, they both disappear. The only way of making return must show all.

  Note that the expressions work perfectly with conditional text on the pages of body. Apparenlty that they do not work on master pages. This seems to be a bug, no?

  I withdraw this question: you can have variable conditionalized on master pages and control them with expressions, provided your expressions do not confuse FM. For example, in the chapter, I have this expression:

  "NotInHelp" ANDNOT "hidden" ANDNOT "SalesPM" ANDNOT "HelpOnly" ANDNOT "Report_Caching."

  The first tag condition, NotInHelp, to which we are asking FM to show (the others hid), is the cause of all hide conditionalilzed, even if it worked properly when we tested it in an individual file.

  Remove "NotInHelpAND" solved the problem. Learned something about expressions today. fun!