Ezvpn configuration

Hi all

Can someone tell me how to configure cisco easy VPN Server and client on IOS router (with diagram)?

Here we go:

http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080808395.shtml

Hope that helps.

Tags: Cisco Security

Similar Questions

  • Hub VPN3030 as server EzVPN configuration

    Hello

    I want to configure the hub of VPN3030 as a server of EzVPN to C3845 router that will work as an EzVPN remotely. That's a good tech note that shows how to do this in the VPN3030? In addition, any ideas to set up the remote router for EzVPN is greatly appreciated as well. Thanks in advance.

    Keith

    The following configuration example is between Cisco VPN 3000 and Cisco 1721 router. Configuration of the router should be more or less similar.

    http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800945cf.shtml

    I hope this helps.

    AK

  • Cannot SSH in ASA after EZVPN configuration and do not specify "split-tunnel-political tunnelspecified.

    Even after the "split-tunnel-policy tunnelspecified" specification with "split-tunnel-network-list value TUNNEL of SPLITTING" and denying all traffic to the public IP address of the ASA, I'm still not able to SSH in the firewall. Everything else seems to work OK, but I have to be able to handle the ASA from the public interface. In fact, I expect little given the mean one sa is the installer for the tunnel, and it would seem that a deny statement would be ignored, but perhaps there is a way around this. Thank you.

    If you want to connect to your home IP through the tunnel, you must specify 'inside access management:

    http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/a...

    Best regards, Karsten

    Sent by Cisco Support technique iPad App

  • EzVPN and RADIUS

    I configured a router to use Radius (MS IAS) for console connections and telnet. I also want the vpn users who connect to this router to be authenticated with the Radius server. I have configured the router but I am not able to get the vpn client that is connected to the router (ezvpn server)

    The configuration is below the router:

    Router #sh run

    Building configuration...

    Current configuration: 1585 bytes

    !

    version 12.4

    horodateurs service debug datetime msec

    Log service timestamps datetime msec

    no password encryption service

    !

    router host name

    !

    boot-start-marker

    boot-end-marker

    !

    !

    AAA new-model

    !

    !

    RADIUS AAA server AUTH group

    auth-port 1645 172.16.1.243 Server acct-port 1646

    !

    RADIUS authentication AUTH of AAA connection group.

    Group AAA authorization exec default RADIUS

    Group AAA authorization network AUTH RADIUS

    !

    AAA - the id of the joint session

    memory iomem size 5

    !

    !

    IP cef

    !

    !

    dhcp-pool IP address pool

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    crypto ISAKMP policy 10

    BA 3des

    preshared authentication

    Group 2

    !

    ISAKMP crypto client configuration group AAA

    vpnuser key

    DNS 10.0.1.13 10.0.1.14

    domain cisco.com

    Remote control-pool

    Save-password

    !

    !

    Crypto ipsec transform-set esp-3des esp-sha-hmac VPNTRANSFORM

    !

    Crypto dynamic-map Dynamics-plan 10

    game of transformation-VPNTRANSFORM

    market arriere-route

    !

    !

    list map ClientMap client of authentication AUTH crypto

    card crypto ClientMap AUTH isakmp authorization list

    client configuration address map ClientMap crypto answer

    dynamic ClientMap 65535 dynamic-map ipsec-isakmp crypto map

    !

    !

    !

    !

    interface FastEthernet0/0

    IP 172.16.1.241 255.255.255.0

    automatic duplex

    automatic speed

    map ClientMap crypto

    !

    IP pool local Remote-pool 10.0.1.100 10.0.1.150

    IP http server

    no ip http secure server

    !

    !

    !

    radius of the IP source interface FastEthernet0/0

    !

    !

    RADIUS-server host 172.16.1.243 auth-port 1645 acct-port 1646 key xxxxxx

    !

    control plan

    !

    !

    !

    !

    !

    !

    !

    !

    !

    !

    Line con 0

    exec-timeout 0 0

    line to 0

    line vty 0 4

    authentication of connection AUTH

    !

    !

    end

    When I compose using Cisco Easy VPN Client I get a debug error of:

    % CRYPTO-6-IKMP_NOT_ENCRYPTED: IKE 172.16.1.242 package was not encrypted and it should have been.

    I searched on google and thought that the problem would have been the group ID and password

    In my case, the ID of group is AAA and password is vpnuser.

    But still I can't VPN in the router.

    I think it is a problem related to AAA, because in the books, I've read and seen the EzVPN configuration using the local database and here I am their authentication with IAS. But it should work fine because I'm able to telnet to the router using my Active Directory/IAS account i.e. [email protected] / * /

    Help, please

    Change this line:

    Group AAA authorization network AUTH RADIUS

    to be

    local AAA AUTH authorization network

  • EZVPN 2811 router VPN module

    Hi all

    I have a spare 2811 router that would like to use for the temporary easy VPN server.

    the router IOS is already updated security advance 15.0 K9.

    My question is the AIM - VPN a real map/module on the motherboard of the router or just pop up once the router has been upgraded to IOS security?

    SH ve | I have IOS
    Cisco IOS software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 15.0 (1) M8, RELEASE SOFTWARE (fc1)

    #sh inv
    NAME: "2811 chassis', DESCR:"2811 chassis.
    PID: CISCO2811, VID: V02, SN: FTX0911Cxxx

    NAME: ' PVDMII DSP SIMM with a DSP on the Slot 0 SubSlot 4 ', DESCR: 'PVDMII DSP SIMM with a DSP.
    PID: PVDM2-16, VID: V01, SN: FOC13071xx

    NAME: "virtual private network (VPN) on the Slot Module 0 ', DESCR: 'encryption PURPOSE Element '.
    PID: AIM-VPN/EPII-PLUS, VID: v01, SN: FOC09072xx

    You have now two VPN modules in your router:

    1. The module for basic needs
    2. The module see you in "inventory to see the" which is placed in the OBJECTIVE of on-board connector. This module has a flow more and a greater number of tunnel and will be used by default.

    There are many examples of EzVPN configuration guide:

    http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_esyvpn/configuration/15-Mt/sec-easy-VPN-15-Mt-book/sec-easy-VPN-Srvr.html

    If it is more then a temporary solution, I would also consider using an ASA to remote access VPN. EzVPN is more or less obsolete, and the ASA has many more features with the AnyConnect client. On the router, you can also configure remote access for AnyConnect, but it is much more complicated.

  • Order ezvpn-rays for the set of cryptographic keys IOS

    Hello

    In model documents of SNF 2.0, I see that the command below is required for configuring ezvpn to the IOS server.

    door-key crypto ezvpn-rays
    pre-shared key address 0.0.0.0 0.0.0.0 key #.

    I've seen other config ezvpn models if this command is not used. Is this order a requiment for server ezvpn configuration?

    It would be to offer connectivity for ezvpn client using a software configuration of the router and cisco vpn client remote TV ezvpn.

    Anyone with and insight on this.

    Andy

    Hello

    A Keyring is a repository of pre-shared key and public key (RSA).
    The set of keys is used in Setup mode profile ISAKMP.
    The ISAKMP profile finalises successfully authenticating peers if the keys peer
    are defined in the Keyring which is attached to this profile.

    This command is not required, is just a way to match a set of keys to an ISAKMP profile
    (if you use profiles).

    Federico.

  • EzVPN in 7606S with SPA-IPSEC2 - 2G

    Hello...

    PLS, I need help.

    I am trying to set up a router 7606 S with SPA-IPSEC - 2 G for EzVPN but I have no idea on how.

    I read some examples of documentation centre 7606, but with the current configuration in our router I do not know how to do it.

    The router has the SPA installed in the Groove 3, G3/0/0 interfaces and G3/0/1.  The router has the interface G2/0/0 is connected to our provider and we connected directly to the network interfaces. That is to say: not VLAN, not trunks, ports configured as IP ports directly connected to the network.

    Where can I find an example of EzVPN configuration?

    Does anyone has an idea to do a simple config?

    Thanks in advance...

    Here are all the configuration guide for the router 7600 Series SPA IPSEC module:

    http://www.Cisco.com/univercd/CC/TD/doc/product/core/cis7600/76sipspa/sipspasw/76vpnspa/76cfvpn1.htm

    There are 2 modes with SPA-IPSec module:

    (1) connection crypto mode

    (2) mode VRF

    This will determine how interfaces are connected, and once you have the above configured, EzVPN configuration is identical to normal router config.

    I hope this helps.

    Post edited by: Jennifer Halim

  • Traffic no routing between remotes using ezVPN with NEM

    I scoured the forums for a while now, looking for ways to solve this one but just can't find anything that helps.  I ezVPN configured on an ASA 5520 for my server with 5505 s like my clients at several remote sites.  The tunnels go up without a problem and I can hit what I need on both sides of the tunnel, but I'm not able to go to another remote network from a remote network.  Traffic shuts down the tunnel on the 5505, but on the 5520 I don't see is a bunch of scrolling tear down messages.  Any thoughts would be greatly appreciated.

    Side hub

    interface GigabitEthernet0/0

    nameif Inside_Network

    security-level 100

    the IP 10.0.0.1 255.255.255.252

    !

    interface GigabitEthernet0/3

    nameif Outside_Network

    security-level 0

    IP 192.168.32.8 255.255.255.0

    !

    permit same-security-traffic inter-interface

    !

    Router eigrp 10

    Network 10.0.0.0 255.255.255.0

    redistribute static

    !

    Crypto ipsec transform-set ikev1 my - set esp-aes-256 esp-sha-hmac

    Crypto-map dynamic ezvpn 30 set transform-set my - set ikev1

    Crypto-map dynamic ezvpn 30 the value reverse-road

    map outside_map 65535-isakmp ipsec crypto dynamic ezvpn

    outside_map Outside_Network crypto map interface

    Crypto ikev1 enable Outside_Network

    IKEv1 crypto policy 10

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    !

    internal VPN_GP group policy

    VPN_GP group policy attributes

    VPN-idle-timeout no

    allow to NEM

    !

    username password encrypted Wj0QXCAEhK12A5Sp privilege 0 vpnuser

    !

    VPN Tunnel-group type remote access

    General-attributes of VPN Tunnel-group

    Group Policy - by default-JEOD_VPN_GP

    Group-tunnel VPN ipsec-attributes

    IKEv1 pre-shared-key *.

    Remote side - more than necessary here

    vpnclient Server 192.168.32.8

    vpnclient mode network-extension-mode

    vpnclient vpngroup VPN password *.

    vpnclient nickname vpnuser password *.

    vpnclient enable

    EzVPN remote clients can connect to the Headend ASA5520 but cannot communicate with each other. Is it correct to understanding?

    All guests of EzVPN are end on a different external physical interface of the ASA? If not, we will have to allow intra-interface traffic too with inter-UI that is same-security-traffic permit intra-UI.

  • Customer behind EzVPN remotely (ASA 5505)

    Hello

    I try to set up a simple EzVPN infrastructure:

    EzVPN Server (CISCO2811, hostname cme) < --=""> EzVPN remotely (ASA5505, hostname ezvpn - asa) < --=""> Client

    Attached you will find the two server EzVPN configuration and remote control. The tunnel is getting up and if I ping from the ASA to the router, I see the packets be encrypted:

    ezvpn - asa # ping 172.16.100.1

    ...

    ezvpn - asa # crypto ipsec to show her

    Interface: outside

    Tag crypto map: _vpnc_cm, seq num: 10, local addr: 172.16.100.2

    _vpnc_acl the host 172.16.100.2 ip access list permit 172.16.100.1

    local ident (addr, mask, prot, port): (172.16.100.2/255.255.255.255/0/0)

    Remote ident (addr, mask, prot, port): (172.16.100.1/255.255.255.255/0/0)

    current_peer: 172.16.100.1, username: 172.16.100.1

    dynamic allocated peer ip: 0.0.0.0

    #pkts program: 5, #pkts encrypt: 5, #pkts digest: 5

    decaps #pkts: 5, #pkts decrypt: 5, #pkts check: 5

    compressed #pkts: 0, unzipped #pkts: 0

    #pkts uncompressed: 5, comp #pkts failed: 0, #pkts Dang failed: 0

    success #frag before: 0, failures before #frag: 0, #fragments created: 0

    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

    #send errors: 0, #recv errors: 0

    If I connect a customer with IP 192.168.1.2 interface eth0/1 and do a ping to the cme, I see not all packets are encrypted. I have no idea on the VPN, I just need a wireless lab environment. I need to configure on the SAA, so the Interior traffic is encrypted?

    Thanks in advance and best regards

    Dominic

    Hello

    Looks like you are missing split-tunnel list in 2811. Please see the link to the example configuration below.

    http://www.techsupportforum.com/forums/f137/how-to-configure-easy-VPN-server-on-Cisco-2811-router-192775.html

    HTH

    MS

  • L2l with certificates between 2 ASAs

    Hi all

    I want to set up a VPN L2L/Site-to-site tunnel, which authenticates by using certificates.

    In fact I am following this guide-> http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080aa5be1.shtml

    I configured the tunnel group on both ends, with the trustpoint configured, authenticated and accepted specified.

    I correspondent isakmp policies at both ends, and of course my cryptographic cards contains 3 identical lines - set peer match access-list and transformation-a set cryptomap. Next to those, there are 2 identical lines for life. I haven't specified the trustpoint in encryption card while it is not indicated in the top link (guide) to do, even if I tried, without different result. Debugs him happens exactly the same each time:

    Debug the cry isa 10: (on the remote end)

    TEST-ASA-RA # debug cry isa 10

    TEST-ASA-RA # Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + SA (1) the SELLER (13) + the SELLER (13) + the SELLER (13), SELLER (13) + (0) NONE total length: 208

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, SA payload processing

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Oakley proposal is acceptable

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT-Traversal worm 02 VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, worm received 03 NAT-Traversal, VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT - Traversal RFC VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Fragmentation VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: true

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA payload processing

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build the payloads of ISAKMP security

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, construction of Fragmentation VID + load useful functionality

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 108

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 374

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, processing ke payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ISA_KE

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, nonce payload processing

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, the customer has received Cisco Unity VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received xauth V6 VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment VPN3000 / ASA payload IOS Vendor ID theft (version: 1.0.0 capabilities: 20000001)

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Altiga/Cisco VPN3000/Cisco ASA GW VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building ke payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building nonce payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building certreq payload

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads of Cisco Unity VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, constructing payload V6 VID xauth

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send IOS VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, ASA usurpation IOS Vendor ID payload construction (version: 1.0.0 capabilities: 20000001)

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send Altiga/Cisco VPN3000/Cisco ASA GW VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Generating keys for answering machine...

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 298

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, RRs would fragment a new set of fragmentation. Removal of fragments of old.

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, assembled with success an encrypted pkt of RRs would be fragments!

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + ID (5) + GIS (9) + IOS KEEPALIVE (128) + CERT (6), SELLER (13) + (0) NONE total length: 1987

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ID

    Jul 07 11:36:18 [IKEv1 DECODER]: IP = 80.62.240.136, ID_IPV4_ADDR received ID

    80.62.240.136

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing cert

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment of RSA signature

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, calculation of hash for ISAKMP

    Jul 07 11:36:18 [IKEv1 DECODER]: Dump of Signature received, len 256:

    0000: 8D97FE83 CDA9CEB2 A5D7F63F 0FAA76A4...? ... c.

    0010: 21F229A8 2A714C2D 12F16ABF 08E44664!.). *... qL j... FD

    0020: 0D95A510 0AFFA63B 815CCBB0 B7C708CF...; \......

    0030: 31246316 0E93E084 59395461 118C 9251 $1 c... Y9Ta... Q

    0040: 823A36CB 55F2F59C 3342326D 251F8B7A. : 6.U... 3B2m %... z

    0050: B9C9F916 C403A4D1 59DA3AA8 932312C 0... Y.:.. #..

    0060: 88476460 E9C9A07C 5671C18D A9202382. GD'... | DV... #.

    0070: 441F47AF 74E407B1 DB06B929 406E993D D.G.t...) @n. =

    0080: A7C149FA 1677D1A2 E3105356 4E205E45... I have... w... SVN ^ E

    0090: 06D2CB2A B6BF638E 0910283C 7FF6BAE2... *... c... (<>

    00 to 0: 3F97ADF5 19B 78872 69C0346B 7EF89FAE?... ri.4k... ~

    00B 0: 456E26CF 52CC296B 11F6AE68 2498024C en &. R) k...h$... L

    00C 0: 74658112 you 16121A 68 h

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IOS treatment keep alive payload: proposal = 32767/32767 sec.

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

    Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, DPD received VID

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, trying to find the group via IKE ID...

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, connection landed on tunnel_group 80.62.240.136

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, case of mistaken IKE MM Responder WSF (struct & 0xd3dcecf0) , : MM_DONE, EV_ERROR--> EV_COMPARE_IDS--> MM_BLD_MSG6, MM_BLD_MSG6, NullEvent--> MM_BLD_MSG6, EV_VALIDATE_CERT--> MM_BLD_MSG6, EV_UPDATE_CERT--> MM_BLD_MSG6, EV_TEST_CERT--> MM_BLD_MSG6, EV_CHECK_NAT_T, EV_CERT_OK--> MM_BLD_MSG6

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, IKE SA MM:1e531705 ending: 0x0100c002, refcnt flags 0, tuncnt 0

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, sending clear/delete with the message of reason

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, payload of empty hash construction

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, constructing the payload to delete IKE

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, build payloads of hash qm

    Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 5a228b67) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, Removing peer to peer table does not, no match!

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, error: cannot delete PeerTblEntry

    Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

    Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

    Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

    Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

    Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

    Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

    Then, it waits a bit and start over. No matter if I am trying to establish the tunnel network or remote endpoint - there is no difference in the result.

    I made a line of debug output "BOLD" - I don't the have not seen this before, don't think that devices Cisco used this alternative area? Thought it was Microsoft?

    1 thing is a reference to the certificates - I use my won Microsoft PKI based on 2003 servers. I have 1 Root CA and 2 subordinates. The root CA is stopped. During the construction of my trustpoints, I start to do my request, give it to one of subordinates, gets my identity certificate and save it on my computer. Then check the chain, which looks always good - RootCA-> SubordinateCA-> ClientCert. Then I extracted the subordinate cert, to authenticate my trustpoint and finally I import the certificate of identity. No complaints, it of all good - and actually working like a charm for my EZVPN configurations.

    So I do not think the problem it's with the certificates, although the release said that there is an incompatibility with the other name in question.

    The debugging online after this statement, I understand not quite - maybe someone can help me with this? Because right after this line, he begins to destroy the tunnel.

    I can provide from configs if necessary, but really, it corresponds to the configuration contained in the guide.

    / Peter

    Can you check the "crypto isakmp identity" command on both sides?  He looks like a side sends the IP, when it expected the certificate DN is the name so it can match the value in the cert.

    Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)

    Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt

    -Jason

  • Internet via VPN

    Hello

    I have a server EZVPN configuration and it works well. Client can connect to the LAN on the EZVPN server side. I have not split tunneling so local LAN access to the customer is lost.

    Currently, when the VPN client is connected, they are not able to get internet through their LAN or VPN. I would like it so they could get internet access (WAN) through the VPN tunnel. Is this possible?

    Thank you

    Hello

    Yes, not really familiar with the router side of this. I think that its probably works not because of NAT rules or the router does not correctly forward traffic

    Here are some links that I could find on the subject. I don't know if they are of any help

    Router and VPN Client for Internet audience on a stick Configuration example

    http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_configuration_example09186a008073b06b.shtml

    Cisco VPN Client Configuration - installation for router IOS

    http://www.firewall.CX/Cisco-technical-Knowledgebase/Cisco-routers/809-Cisco-router-VPN-client.html

    -Jouni

  • EasyVPN server and DmVPN

    Hi all

    I have a router with IOS advanced ip services 12.3.T3 1760 and it is configured as a hub dmvpn and it works very well and the rays work too. I want to know if it is possible to configure easy vpn server on the same router, and both services are running at the same time?

    Concerning

    Raul Hey how's it going?

    The answer to your questions is Yes, remember that the server EzVPN configuration is like the configuration of the device for remote access VPN client.

    I don't see why it does not work...

    In fact, a Cisco IOS router can be configured as a server EzVPN & Client at the same time restrictions are for EzVPN client, it will be able to connect to a single server of EzVPN and nothing else.

    Hope this helps

    Frank

  • is it possible to create a tunnel my router to my ASA 877 VTI

    Hi all

    I woulke would like to know is possible to create a tunnel VTI my router 877 to my ASA, rather than create a cryptomap on the router?

    see you soon

    Carl

    Yes, you can

    I forgot to add that it is possible during the ezvpn configuration where the 877 is a remote client and a server Asa

    Sent by Cisco Support technique iPhone App

  • IPsec Security Association keep it up

    Hello community,

    Customer has about 50 distance 871 s (home) with IP phones.

    Main site has ASA 5510 sheltering the CUCM.

    Problem is...

    When user1 calls user2 there no audio data (since there is no built between remote users IPsec security association).

    The fact that user1 called user2 built IPsec between ROUTER1 and ASA, but since there is no IPsec security association for users between ROUTER2 and ASA, audio fails.

    If User2 calls user1 now, then the call is successful, because the SAs are built:

    IPsec security association between ROUTER1 and ASA for the traffic of user1 and user2

    IPsec security association between ROUTER2 and ASA for the user1 user2 traffic

    So, the problem is that both parties must open up traffic to make this work.

    What I did to solve the problem, is to configure IP SLA on routers to send a PING packet every 10 minutes at their home by peers (thus keeping the SAs between remote sites all the time).

    IP SLA works, but I'm looking for a better way to solve the problem of having to manually launch the traffic (DMVPN or running as one routing protocol does not work with the ASA through the tunnel).

    I guess to increase life expectancy IPsec Security Association is another option.

    Looking to get recommendations, thanks!

    Federico.

    Hi Federico,.

    Have you considered EzVPN/Easy VPN, with ASA like server EzVPN configuration and Clients (routers/ASA5505) as clients of EzVPN? This would create the tunnel as soon as it is configured.

    In addition, apart from the increase in the life expectancy of the AA (which is basically report to generate a new key stage 2), you can configure vpn-idle-timeout to be 'none' in the group-policy framework of the SAA.

    Any thoughts?

    Kind regards

    Praveen

  • remote router configuration with EzVPN NEM by VPN

    I have the following scenario: Some 836 routers Cisco EzVPN network are connected to a hub VPN 3005 in the main façade.

    The work of LAN-to-LAN connection and I can also telnet via the VPN from a PC to the main façade of a router to a remote site using the address LAN IP of the remote router as a destination. But does not work for example do a "copy run tftp" on the remote router to the LAN of the main façade.

    My questions now are:

    Is it possible to transfer the remote routers configuration file or via the VPN IOS image between the remote router and the LAN at the main façade?

    And, if possible, how do we?

    Thanks in advance

    Mark

    When you make a "copy run tftp" from the remote router, it goes to the source of its external interface TFTP packets, not its interior. The external interface to your local network packets are NOT included in the list of packages to be encrypted, and therefore they lose.

    You must specify the router to the source its TFTP packets from the interface IP address inside, then these will be correctly encrypted and sent through the tunnel.

    The following command should do the trick for you:

    IP tftp source-interface

Maybe you are looking for

  • How to remove a plungin

    There is simply a plungin I want

  • Why is there no USB - C good docks yet?

    I was wondering, with all these beautiful fake USB - C docks in startup mode for (sometimes) more than a year: what's the problem? I feel that there is a lack of decent and reliable USB - 3.1 chipsets. Apple may have taken the measure to USB - C far

  • Satellite Pro A300 PSAJ1E: Touchpad not recognized using Win XP SP2

    Hi all I just got a Satellite Pro A300 PSAJ1E, which is preloaded with Vista. It is also comes with a 'product' XP SP2 recovery CD I had to use because of some software work with Vista compatibility issues. Unfortunately, everything works well except

  • Tecra M5 docking station problems

    Hello I don't know if this has happened elsewhere, but my Tecra M5 (Win XP / SP 3 / fully updated on MS) boots when undocked, but hangs on the appearance of the first "Loading Windows" screen Re-booting subsequently always results in the typical menu

  • How to remove photos from my iPhone 6s more without deleting them from iPhoto?

    Title says it all, but here: I have an iPhone 6 Plus and I want to free up space for my Photos app. If I do this, it will remove those download in the Photos on my Macbook? Should I back up their first somehow? If Yes, what is the best way to save ph