Façade Dell optiplex 3010 problem

Similar Questions

• (Redirected) Power Supply for dell optiplex 3010 & optiplex 390

  Hi, may I know how much cost for dell optiplex 3010 & optiplex 390 power supply, because

  my diet already dead and how I want to order it... :(....

  Hi Nathalie,.

  Please repost this in the forum Office help.

  http://en.community.Dell.com/support-forums/desktop/

• Memory Dell optiplex 755 problem

  I recently acquired a Dell Optiplex 755 used with 4 GB of memory Kingston (KVR800D2N5K2).

  I replaced it with 8 GB memory Kingston (KVR800D2N6).

  When I plugged in the computer, it went through it, self test has virtually stopped with just the power led (green) and I could not activate it (no follow-up post). I quickly removed the memory and give the original 4 GB and got on with the post office to come fine.

  My only question is to go from CASE 5 6 because the problem or is the memory just bad?

  Thanks in advance.

  Found the solution, when I asked questions about memory, I discovered it was the memory of type AMD. Where the reason for which he would not start on the motherboard Intel 755.

• CPU Dell Optiplex 755 problem

  Hello, I was told in one of the forums that a PROCESSOR Intel CORE 2 QUAD Q9650 SLB8W 3.0 GHz, 12 MB CACHE 1333 MHz FSB would work in my office. I bought on E - bay and installed with the bios already upgraded A22. It did not work. I tried to install my original CD which worked and now I can not do, even after. I removed the battery for an hour and that did not help. I tried a different video card in case that was the problem. I get absolutely nothing on the screen. I am at a loss. Does anyone know a thing or two to get it back running. I thank very you much for your time. Robb

  What error POST or the diagnostic lights get you that indicate an error?

  Here is your manual: ftp://ftp.dell.com/Manuals/all-products/esuprt_desktop/esuprt_optiplex_desktop/optiplex-755_user%27s%20guide_en-us.pdf

  You can try to clear the CMOS memory.

• Driver of Bus SM Dell optiplex 790 problem

  Hi all

  Another system, I had to upgrade to windows 7. Everything works, but I get frequent error of missing under devices SM bus. Its possible maybe I installed the wrong firmware or missed a chipset driver. I did an analysis of the system and chipset driver and driver management Intel that is used by this PC offered by Dell. When I try to install these drivers, however, I get an error of failure as shown below. Can someone point me to the right of the optiplex chipset driver 790 or update the SM?

  

  Error when you try to install the chipset driver

  

  32 - or 64-bit Win 7?

  For 64- bit:

  1. Chipset v9.2.0.1019 (looks like a newer version that you tried to install)
  2. Intel Management Engine
  3. Unified Intel AMT 7 management engine
  4. Driver NEC USB3

  If necessary, restart in Mode safe to install the Chipset.

• Boot Dell Optiplex 3010 for controller SATA III card

  I upgraded my office 3010 to SSD for the boot drive and it worked very well for the SATA II ports on the motherboard.  I installed a Syba SATA III controller card and it is visible in Device Manager and doesn't show any errors.  When I connect the SSD boot to the controller card, the system doesn't see a bootable disc.  I'm not familiar with UEFI in the GUI of the BIOS so I don't know how to make a new section that will work.

  No boot UEFI without paying fees to microsoft for the certificate in the bios.

  Legacy of the CSM is the only way to 3rd-party storage Option ROM to boot.

  Once we get to class 3 Bios Legacy is gone! Fresh start prevents loading not sure $Microsoft paid bootloader.

  Change secure boot for Legacy GPT CSM requires complete reinstallation of the operating system.

  

  

  

• Lights diagnostic OptiPlex 3010 Mini-Tower 3 & 4

  Hi all, I'm new to this forum. 2 years ago, I bought a dell optiplex 3010 mini tour, suddenly, it stopped working, I have no screen, no video or any kind of sound, the only thing it does is to turn on the lights of number 3 & 4 on the front panel. What can I do?

  Thank you

  erickfv12

  Hi all, I'm new to this forum. 2 years ago, I bought a dell optiplex 3010 mini tour, suddenly, it stopped working, I have no screen, no video or any kind of sound, the only thing it does is to turn on the lights of number 3 & 4 on the front panel. What can I do?

  Thank you

  erickfv12

  3 & 4 usually diagnostic lights indicate a memory problem, see page 42 here:

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_optiplex_desktop/OptiPlex-3010_Owner%27s%20Manual2_en-us.PDF

  First of all, try the following:

  Remove and reinstall all memory modules and try to start the system, to see if that makes a difference.

  Still does not start, remove all the memory modules [page 14] and then install only one module in the connector 1 and see if the system starts, and if the computer starts normally, reinstall an additional module.
  Do not start, move the module in slot 2 and still a time see if the system boots.

  Still does not start, then remove the first module, and using the other, repeat the sequence described above.

  Still does not start, purchase a new compatible memory module and try that.

  Then, if the computer still does not start, it is possible that the motherboard has failed and must be replaced.

  Bev.

• OptiPlex 3010 upgrade of RAM!

  Hi, I have a dell optiplex 3010 with Intel i5-3470 processor and 4 GB of RAM and I want to update 8 GB or 12 GB / 16GB, sort of Rams which are compatible with my own desktop (8GB / 4GB per slot, 800/1033/1333/1600 Mhz by RAM) and I searched for compatibility with Ivy H61 bridge (normally (, it should be my motherboard), but I did not pay what I'm looking for.
  Thanks for the help!

  Hello

  Thanks for joining us.

  This machine can hold up to 8 GB of RAM.

  The type of RAM installed on your PC is DDR3

  The speed of this motherboard supports

  • DDR3 1333 MHz (Non - ECC)
  • DDR3 1600 MHz (Non - ECC)

  I hope this helps.

  Thank you

• Problem with the Dell Optiplex 755.

  Have a refurbished Dell Optiplex 755 with windows 7, only a few months ago.  Sometimes the screen rises all yellow and you can't get out.  Sometimes screen goes all black but if you click anywhere on the screen with the mouse will go up all that is behind the screen where you clicked, but you must do it all over the screen to see what is there.  Now the last week or so whenever you leave the computer and return windows has recovered from an unexpected shutdown down.  Can someone tell me what could happen?

  This behavior indicates a video problem.

  A cable loose or damaged video from your computer to the screen.

  A failed video monitor.

  This computer has a separate video card?  If the cable connected to the back of the PC is vertical, the answer is probably no.  If it's a separate video card, you need to open the PC and remove, then reinsert the video card - its called re-seats of the Board of Directors.

  How old is follow you and what type is - LED or CRT.  Is - this really really heavy?

  Remove and check the end of the thread and examine the tiny pins in the connector, none of them are bent?

  The judgment is not likely related to changing the color on your screen.  A number of things that cause, but you need to check your hard drive and check the temperature inside the box.

  Turn off the power.  Hold the button for 7 seconds.  Open the case and see if there is a lot of dust.  Have one of those cans of compressed air.  Blow off the dust from the case.  Pay special attention to the fan on the processor with the fins of the radiator aluminum under him.  Make sure that it is free as well as fans of dust.

  You should test the hard drive to ensure that it is not a failure.  If you tell us the manufacturer of the drive, we can tell you where to find the appropriate software.  In the text box above the globe on the left lower part of peripheral type.  Type of device.  Click on Device Manager.  In the window that appears, click the small arrow to the left of the disc.  Send us the model number, you can see it.

• Unauthentication problems with a Samsung Windows 7 Starter (installed in a DELL Optiplex 210 L PC desktop..) CD after detection... !

  I have here an unauthenticated Version of A Windows 7 Starter for the Desktop PC (A DELL Optiplex 210 L PC Desktop that..!). The screen or wallpaper suddenly turned 'BLACK' after Microsoft detected it was supposed to BE NOT AUTHENTIC... Can you help me with this problem.., because, from my point of view, it's a GENUINE copy of A Windows 7 Starter, which I downloaded from a Samsung Windows 7 installation CD (which came with my Samsung NC - 110 Netbook..!)... ? Thank you

  You cannot transfer an OEM of Windows version to another computer. It can only be used with the computer on which he came with.

  You must install Windows with a disk that came with the Dell printer, or buy a new copy of Windows.

  The OEM versions can only be used with the computer, on which it was initially installed.

  They are not transferable!

• alert! system battery is low problem for dell optiplex GX620 Tower

  alert! system battery is low problem for dell optiplex GX620 Tower, how do I fix or solve this problem, is this will solve by change coin cell? If yes than suggest me about the cell its name will be full description

  The battery is a battery CR2032 DL2032.  In the USA they are in grocery stores in the pharmacy section because the readers of blood sugar using the same battery.

  http://www.Walmart.com/c/KP/CR2032-batteries

  

  

• OptiPlex 3010 - PCI-e slots to prevent sleep?

  I have an Optiplex with Win7 pro OS 3010.

  I have a (RC-305th) Rosewill 4 port RS232 Serial Card occupy one of the card PCI-Express slots on the motherboard.  The serial ports work fine except when the system is idle.

  Everything works, application, leaving the serial device connected to the card.  When I come back a few hours later, as long as the next day, the application using the serial RS232 port has stopped working.  He reads is no longer the serial device.  Swtpping the application, then by restarting has sometimes everything works again.  Other times I have to restart the PC.

  I went the power settings and have done everything to NOT go to sleep.  It is my understanding that the PCI-Express request mode specification 'sleep' when idle.  What I want to do is to disable this option completely.

  All ideas and thanks for the help.

  -GS-

  I knew a lot of trouble when the maps in the series contain the MOSCHIP on DELL OptiPlex 3020 chipset.   I think you'll find that Rosewill RC-305th contains this chipset.  I bought two cards series both with the same CHIPSET (STARTECH VANTECH), the two MOSCHIP chipset.  Serial devices had been set up for weight scale Truck Stop (9406 Fairbanks series) in a Serial Communication continuous with continuous data flow.

  Requirements for my Serial Communication:
  Scale software installed on DELL OPTIPLEX passively listen to the COMM PORT communication as long as the COMM Port is opened by the software.  The scale of Fairbanks send data via an interface series in a constant loop.  What I find is the MOS chipset is idling somehow over time.   If I close and open the PORT Serial Communication will continue to listen passively to the stream.
  

  I had the following problem with the map:

  -Card series would have slowed after a period of TIME (5-15 minutes).   Initially the problem was related to PCIe power saving features, but I'm sure that issues are assigned to the MOSCHIP so.  In general, I have to CLOSE and REOPEN the port for the serial card process the incoming data stream

  -After a period of time (a few days) the map would pass the bone, (not available in the device Mgr).  Attempts to remove the CHUCK, restart, reinstall the driver did not find the MOSCHIP series card.   To get the card works to new necessary physically reinstalling the card in a different SLOT PCIe for the operating system to recognize the serial card

  Requirements for successful communication:

  -Turn off all Power Saving settings in BIOS
  -Disable all CommPorts onboard in the BIOS
  -Disable all Options Windows power functions, specifically:
  -State of the PCIe Power Management links - OFF
  -Selective suspension USB setting - DISABLE "this should not be necessary w / PCIe.

  CORRECTIVE ACTIONS:  Buy a card series PLX/OXFORD OXPCIe952 chipset.  For my DELL 3020, 7020, 9020 Optiplex machines) I have been using the STARTECH PEX1S1P952 (containing the PLX/Oxford - OXPCIe952 chipset) like this work for my needs.

  My hope are some my find this useful.

• OptiPlex 3010 with third-party RAID controller

  Hello

  I installed an Adaptec RAID 1220SA controller in an Optiplex 3010 and contains two HARD drives in the annex. It is not all disks connected directly to the motherboard. The RAID card, or readers connected to it are visible in the BIOS, so they cannot be selected as boot devices.

  The machine starts OK, past through the initialization of the controller RAID OK, but then it stops with a 'no hard drives detected' attention, giving 3 choices: continue, go to the bios, go to the automatic test utility.

  However, if (continued) F1 is pressed, it starts perfectly among the RAID drives and everything works as expected.

  Any ideas how to get rid of this error/warning message?

  Hi nehamanoka,

  I got the same problem as you, only with an Optiplex 7010 and also an Adaptec 1220SA and a Promise Fasttrak TX 2300 raid controller.
  (press F1 to continue...)

  I also tried a lot of things and my 7010, she collaborates with the following parameters of the BIOS (Dell):

  General - startup sequence: drive HARD internal
  System - integrated NIC configuration: enabled w/PXE

  I have no idea why it works now and I had no problem with a 790 Optiplex.

  HTH

• OfficeJet 4650: how to connect 4650 HP to Dell Optiplex under XP, INTERNET CONNECTION NOT

  I have an old Dell Optiplex Windows XP on which I have my checkbook in Quicken.   This machine is not and will never be connected to the Internet.  I'm trying to install the 4650 on that software from the CD, but he insists on the final step which is Internet check-in.   What should do?

  Hi DocCottle,

  It seems that I understood the problem.  I am running XP SP2.  I've upgraded to SP3 and voila!  the printer now works perfectly.  Sorry to have left out retail SP2 when I asked for help, but your help is very appreciated nonetheless.

• PXI-8360 (MXI-Express) PCI-8361 + Dell OptiPlex 9020 = "device cannot start." (Code 10) »

  Hello

  I have a chassis PXI-1050, conencted to a Dell OptiPlex 9020 via a PXI-8360 and a PCI-8361 (identified as 199392B - 01L). It is Windows 7 64-bit. I can't start Windows very well, but MAX can't see all my PXI hardware. The Device Manager has also 2 inputs "PCI standard PCI to PCI bridge" with exclamation points.

  I placed an old FireWire PCI card in the same dwelling and recognized PC. Thus, the slot went very well.

  I transferred the PCI-8361 to an old PC that contains older drivers, and he acknowledged all my PXI hardware. For example, PXI gear works fine.

  What could be the problem? Here's a screenshot of my software OR installed. I think I installed all the drivers I need. I checked NI Update Service; There is no update of Critcal, and only updates and Service Packs listed are 2013 LabVIEW and TestStand 2013.

  

  JKSH,

  I look in that little bit more and think that I now know enough to be dangerous.

  The BIOS allows the PCI Express native control mode in Windows.  PCIe natively do not like some of the architecture when you use the PCI card version, so it disables the bridges on the PXI card.  I can tell that your OS is PCIe natively because it lists one of the ports as "PCI standard PCI Express to PCI/PCI-X bridge" Device Manager like you posted.

  I found that you can disable PCIe native mode, if you want to try it (but in general using the card PCIe is a better option).  Here are the steps:

  -Open the start menu and type "cmd" in the search box; Right click on "cmd.exe" and run as administrator.

  -In the command window, type "bcdedit/set pciexpress forcedisable.

  -Reboot.

  I don't think it would break anything (it doesn't have on a system I've tried).  If you want to reverse the trend, the command is ' bcdedit/set pciexpress by default'

  -Robert