Failed to connect to VCS

have a physical running 7.2.2 VCS software as a controller.

Somehow the configuration has changed so that it tries to authenticate remote access connections via LDAP that has not been configured.

Therefore, all web access seems to be dead, but I can connect via the console cable to make changes.

But I can not find in the settings of xconfinguration where I ask the system to use the local database for authentication for admin and user.

any help is appreciated

Hi Richard,

Even if the LDAP protocol fails your works local authenticaton if in the configuration you set on connection remote "both."

Coming to your problem, if you have root access, so you can connect through the root and then run the command 'tsh' which takes you to t-shell basically admin login.

Run the command "xcommand DefaultValuesSet level: 2"he will wipe away your configuration of the LDAP authentication. "

Now you should be able to log in as local administrator through web page. If you have admin password then connect through root again and run the command "passwd admin" and reset the admin password.

Rgds

Alok

Tags: Cisco Support

Similar Questions

  • Failed to connect to VCS - e, VCS - c is ok

    Hi all.

    I have now read so many discussions on this issue and I have tried everything that I could find.

    But still I get:

    "Bad username, domain and / or password.

    When I try to connect to Movi from VCS-e.

    Among the things:

    -Area with credentials Check

    -Sip Proxy enabled on VCS - e

    -removed the Provisoning VCS-e key

    -Server SIP Public address added to config TMS model.

    -Tried several tips on the search of VCS - e rules to VCS - c.

    What Miss me?

    Any advice would be greatly appricated.

    Thank you

    Alexander

    Hi Alex,

    collect diagnostic logs and look for message subscribe. See what is happening on VCS - E when it receives the initial response.

    Thank you

    Alok

  • Cannot get mail that failed to connect to my server

    Cannot get mail

    Failed to connect to my server

    Hello parkspa,

    Thank you for using communities Support from Apple. I know have a problem with Mail on your iPhone, it's not what you expect. The good news is the next article will be useful for troubleshooting and solving your problem and get email working again on your iPhone:

    Get help with Mail on iPhone, iPad and iPod touch

    See you soon!

  • Failed to connect, what is my password to overcome this problem?

    Failed to connect to the server imap - mail.outlook.com ; Enter the new password. A new password has been entered, but nothing happened.

    Email passwords are between you and your email provider. Nobody here knows your password.
    The best solution is to find a reliable perspective of supplier and dump. There someone here on all the other days with the same problem with outlook.

  • Get the "Failed to connect to server" error after having my hosting of emails expire and reconnected. Using the latest version of Thunderbird.

    Hi, I am probably doing something really basic and easy to fix but facepalmingly pls have patience with this n00b...
    My emails with Crazy Domains Hosting has expired a couple of months, I've just managed to get it reconnected.
    When I open Thunderbird once again, I kept getting the error msg "Failed to connect to server".
    I checked all the settings for the account, they are all fine as far as I KNOW. Updated to the latest version of Thunderbird, tried to restart the program and doesn't have the obligatory IT Crowd "troid torning it and turn it on again", still get the same message.

    Plaaaaiiss... Halllp!

    Regardless of my fault for typing. What is important is that there is nothing in the DNS or whois on the domain.

    Look at their own whois server it shows pending deletion, expired in April. http://www.crazydomains.com.au/WHOIS/littleredfoxdesign.com/#result

    Until these public information are corrected your not likely to be able to connect because Thunderbird can not find the server. There is no DNS records to point to it.

  • Cannot connect to the system Windows - user profile service failed to connect

    I can't connect my laptop for the 1st time

    I get an e-mail from the user profile failed to connect

    User profile cannot be loaded

    Ideas please

    If you have a Toshiba SSD in your laptop there is a problem in windows 7, making it impossible to connect to the system when the storage TOSHIBA utilities are installed. In this case, you will need to find a way to get the system and uninstalling.

  • Utility of fingerprinting Toshiba - "Failed to connect to the sensor.

    Having a problem with the Toshiba fingerprint utility. The program works fine until I try to use any sort of firewall/antivirus program, even the built-in Windows Firewall: S the scanner still works fine for the boot time scanning, as well as for windows logonm but as soon as any kind of firewall/antivurus software loads up, it fails to connect on the sensor. I added the program to the lists allow but still nothing... So far I tried with AVG Internet Security, Outpost Security Suite and by default, the Windows Firewall. Windows Firewall turned on for awhile, I got when I bought the laptop and there was no problem.

    It's a Qosmio X 500 - 00 X, it uses the same installation of windows when I bought...

    See you soon!

    Hello

    Please update the software of fingerprint. You can find it here:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

    Also try a different firewall and AntiVirus. I have good experiences with AntiVir and Kaspersky Security Suite.

  • Drive not work in IE and saying failed to connect with fingerprint sensor

    Hi all

    I purchased a Qosmio x 500 10 t a couple of months back. For the first two weeks, I had no probs using the fingerprint reader to log on windows and connect to Web sites in Internet exploer.

    All of a sudden it would not work on any website that is stored. The Green banner was shown in the upper part of the site and asked finger drag, but nothing happened when I slipped. I rebooted and it worked again but not for long before failing. This time a restart didn't work so I deleted my fingerprints and Web sites and started from scratch. It worked for a few attempts before probs started. And to try to enter the utility of fingerprint it says the connection of sensor failure. So, I did a system restore. He worked for some time yet and then same probs. So I found the update utility software, uninstalled the old and put on the new. Even once worked for a couple of times then failed.

    I couldn't find anything about it is stuck in the registry but to be on the safe side I did a full system own return to the original using disks of backup configuration. Hey presto, I thought that he had worked. Everything goes ok for the first 24 hours and then same problems start to occur. Only this time it's also prompting me to register fingerprints even if I already have. And when I try to enter the utilioty it says cannot read the sensor again.

    The fingerprints for windows log still works as long as I do not close the utility of fingerprinting before stopping. If I quit the utility I can't reopen it as it says failed to connect to the sensor only. And then I have to uninstall and reinstall the utility software. Aty at the time where he occasionally works on sites stored Web, but most of the time it does nothing.

    Help, please. I have to return Toshiba laptop?

    Have you seen this FAQ?
    + Log on to websites with Authentec Fingerprint Software (TrueSuite) and Internet Explorer 8 +.
    http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=62

    I recommend looking in the forum and read the HowTo and FAQ section in this forum
    Could still be interesting

  • Satellite L855 - 11 p: Win 7 - user profile Service failed to connect

    Can not connect. The message reads user profile Service failed to connect. User profile cannot be loaded"

    Y at - it a bypass key?
    Ideas please.

    Fine machine when I logged out/shut down last night but can not pass this message today.

    Hello

    Please take a look here in this Microsoft Knowledge base article:

    [You receive a "the user profile Service has no logon error message:"] http://support.Microsoft.com/kb/947215]

    There are different ways to fix it.

    Your comments would be appreciated.

  • Tecra A10 with Intel WiFi 5100 running Vista 32 bit fails to connect WiFi

    Hello

    a whole new Tecra A10 with buildin Intel 5100 WiFi fails to connect to the Wlan router, using the pre-installled Vista Business 32-bit. Vista has always said: wrong password.

    Yes, Wifi hardware is enabled, of course. And Tecra WiFi OK MAC is stored in the config of the router. Also the WiFi settings were correct (wpa2-psk aes), corresponding to the Wlan router. Password WPA2 is 13 characters. Connect all the other machines with a Wlan successfully turns a working Wlan configuration and use of the correct password.

    I installed the latest driver on the Toshiba site - without success. I also installed the version of the driver from the Intel site will, too--without success. Doesn't matter what tool I used to connect, Vista itself, or the specific tool of Toshiba (Radar), choice to get an encrypted Wlan connection.

    WPA2 and WPA or WEP can be used. I can't get a Wlan connection when encryption is totally * disabled *! Currently, I use a * clear * Wlan to use this Tecra A10 in the network. Real gross and no solution for more than a few days.

    All other devices in the same network can connect the router Wlan with WPA2-PSK and WEP, no problem. Only the A10 / WiFi 5100 fails.

    Searching the Web I found really many reports all issue of WiFi with a WiFi 5100 devices, so it seems to be a generic material or / and driver issue.

    How can I correct this Wifi 5100 connect problem and use encryption WPA2-psk on Tecra A10 and WiFi 5100 with Vista? If this is not possible, I have to return this laptop and get another model with a working Wifi / Wlan Hardware.

    Thank you.
    -Thomas

    Hello Thomas

    Have you tried to connect your laptop to another router by friends or elsewhere?
    It is really strange that you can use any of the WIFI ciphers available.
    Have you tried to reboot your router?

    I have Satellite A300-1LI with the same card, WLAN, preinstalled with Toshiba recovery WXP image and I use it sometimes linked to the WLAN with WEP encryption.
    Have you tried to contact Toshiba or your local dealer for advice?

  • Satellite P200 - failed to connect to the Windows Services

    After starting Windows Vista on my Satellite P200, I received a message: failed to connect to any Windows Services.The event notification system file are not available.
    Use restricted to the mode of administration.

    No network supports either (wifi, Ethernet,...). At least I can use the PC in batch mode!
    Unable to retrieve a previous saved file system.

    I need to restore my Toshiba restore disk Win Vista?

    Do you offer a lighter solution?

    It's strange, but what you mean with batch mode?
    You can start in safe mode?

    I think the best way is to reinstall Windows with the recovery disk. It only takes a few minutes and then you have the new installation of Windows with all the drivers and tools of Toshiba.

  • PXI: no device (MAX), fail to connect or deploy

    Hello

    I tried to use an SMU-8135 and MAX status is "connected - Running ', but once I try to connect or to deploy from the project it opens a box dialog saying"fail to connect to the target. Also, I don't see no modules currently in PXI on MAX under devices and Interfaces.

    Note: I use LabVIEW Professional 14.

    Thanks for the help!

    I just wanted to update this discussion because I finally solved my problem and it can help people in the future.

    Here's what I did to make it work:

    (1) traded on the SMU ethernet cables

    (2) checked with the cmd I could ping the target

    using MAX:

    (3) uninstalled all the software that was already on the SMU (because I had some questions of dependencies)

    (4) reinstalled the LabVIEW RT module on the system (ensuring that download the PXI components)

    (5) installed the necessary components on the SMU (check that the two LabVIEW RT on the target and the host have the same version)

    After all these, I added the target of a project and could connect without problem.

    I hope that helps!

  • TV SideView and media remote and pair register but fail to connect when you select any operation

    Sony NSX-24GT1

    Installed TV SideView and media on a LGE960 Nexus 4 and ipod touch remote.

    The two seem to associate and register with the TV.

    (Do not get a "set PIN" dialog, however, that I should)

    None of the functions to work. I get the message 'connection' and then 'failed to connect' every time that a

    remote control is attempted.

    When the applications are all first started, I also get the message "connecting" but not him "unable to connect".

    message and the app displays and search operations. The device is displayed in the upper

    to the left of the interface.

    The TV "Manage the IP remote controls" section however does not list remotes IP matched, does it?

    I checked my router and it does not have any features that would prevent communication.

    As the TV recognizes the device wants to pair, indicates to me that this is not the problem.

    -rick

    Follow the steps below to register for your mobile phone with TV SideView app.

  • Profile of user failed to connect

    Profile of user failed to connect.  Paswor does not work.

    Hello

    These methods should help for Windows 7 or Vista.

    References to Vista also apply to Windows 7.

    You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. THE ADMIN
    Safe Mode account has no default password (so unless someone changed
    the password should be available).

    Some programs such as the Google Updater (if you've added the Google toolbar,
    Chrome or Google Earth) has been known to cause this problem.

    Error message when you log on to a Windows Vista-based or Windows 7
    computer by using a temporary profile: "the user profile Service has no logon.

    Unable to load the user profile.
    http://support.Microsoft.com/kb/947215

    Difficulty "the user profile Service has no logon. User profile cannot be loaded. "Error in Windows 7
    http://www.SevenForums.com/tutorials/186131-user-profile-service-failed-logon-user-profile-cannot-loaded.html

    How to fix error "the user profile Service has no logon. Could not load user profile. "in Vista & Windows 7.
    http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

    How to fix error "your user profile was not loaded correctly! You have visited
    logged on with a temporary profile. "in Vista & Windows 7.
    http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

    BE VERY CAREFUL IF YOU USE THIS ONE:

    DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.

    ----------------------------------------------------------------------------------------------------------

    For Windows 7:

    How to enable or disable the built-in Windows 7 Administrator account
    http://www.SevenForums.com/tutorials/507-built-administrator-account-enable-disable.html

    Use the hidden administrator account to lower your user account APPLY / OK then
    Raise it to ADMIN. This allows clear of corruption. Do the same for other accounts
    If necessary after following the above message.

    You can use the hidden - administrator account to make another account as an ADMINISTRATOR with
    your password even (or two with the same password) use a test or difficulty to another.

    You can run the command Admin account hidden from the command prompt
    from there if necessary.

    How Boot for Windows 7 System Recovery Options or use a Windows 7 boot disk.
    http://www.SevenForums.com/tutorials/668-system-recovery-options.html

    What are the system recovery options in Windows 7?
    http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

    How to create a Windows 7 system repair disc
    http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

    ----------------------------------------------------------------------------------------------------------

    For Vista:

    How to enable or disable the real built-in Administrator account in Vista
    http://www.Vistax64.com/tutorials/67567-administrator-account.html

    Use the hidden administrator account to lower your user account APPLY / OK then
    Raise it to ADMIN. This allows clear of corruption. Do the same for other accounts
    If necessary after following the above message.

    You can use the hidden - administrator account to make another account as an ADMINISTRATOR with
    your password even (or two with the same password) use a test or difficulty to another.

    You can run the command Admin account hidden from the command prompt
    from there if necessary.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    What are the system recovery options in Windows Vista?
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

    How to create a Vista - free methods recovery disk
    http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

    ---------------------------------------------------------------------------------------------------------

    If you can't access your old account you can still use an Admin to migrate to one
    new (remember to always leave an account Admin who is not used except)
    to test and difficulty).

    Difficulty of a corrupted user profile
    http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • Fails to connect to the Proxy Server

    My internet works but are used.  He says he "fails to connect to the Proxy Server" is due to firewall settings?  and how to change them.

    Your message is in the forum for people needing help with the anti-malware program from Microsoft Security Essentials (MSE).

    Suggest you contact support OBJECTIVE to: http://help.aol.com/help/product/aim/

Maybe you are looking for