Failover SQLSERVERAGENT error

Similar Questions

• ASA 5540 Stateful failover routing errors

  Hello

  Having two 5540's configuration in a failover scenario. Make the LAN failover and failover state. * See attachment *.

  Failover LAN use 192.168.2.1 as active and 192.168.2.2 as before, with the subnet mask of 30. On both LAN failover use G0/2 and there is a crossover cable connecting them.

  The failover of the State uses 192.168.3.1 as active and 192.168.3.2 as before, with the subnet mask of 30. With "enable HTTP replication" checked in ASDM. On both devices State failover uses G0/3 and there is a crossover cable connecting them.

  The ASDM syslog connects errors every 10 seconds or so to say that:

  SOURCE IP ADDRESS: 192.168.3.1

  DESTINATION IP: 192.168.3.2

  Description:

  "Routing could not locate the next hop for igrp NP identity 192.168.3.1/0 in statefull:192.168.3.2/0".

  The ASA use static routes to meet the network, these roads, there are two, and both are in the 10.x.x.x network. No routing protocol is in use.

  I don't know why these errors are "spamming" my syslog and would like to get rid of them.

  Glad to hear that it works, that's the most important thing. I don't mean to preach, but Cisco does not recommend using ADJUSTABLE wires to fail on. Devices cannot always say that the captain should be and usually causes questions more than a simple link to the bottom.

• Computer memory virtual is increased from 6 to 8 GB and now vm fails to power on with the error massage not enough resources to meet the HA failover, attached screenshot

  Computer memory virtual is increased from 6 to 8 GB and now vm fails to power on with the error massage not enough resources to meet the HA failover, attached screenshot

  The message is usually due to the Admission HA and reservations control configuration memory set on one or more virtual machines. With the default configuration HA calculates the sizes of slot based on the memory and CPU. Any reserve on a virtual machine could increase the size of the slot and lead to fewer available seats. What you can do is either to reduce (or eliminate) reservations about the VM (s) or set admission control to a percentage rather than the host failures tolerated.

  André

• W/failover of cluster HA / DRS activated - error

  Hi all

  I have this cluster of created test and I'm trying to understand how to interpret / to the following address.

  These are a list of my setup general error messages. I hope it will generate a discussion on how to respond to the mistakes of VC.

  Thank you

  ERROR-

  "Test cluster.

  Not enough resources to meet the HA failover the cluster 'Cluster of Test '.

  'Host 1 '.

  HA agent on "Host1" cluster "Test Cluster" in DataCenter1 has an error

  Tab summary 'Cluster of Test '.

  DRS: enabled

  HA: enabled

  Total CPU resources: 13 GHz

  Total memory: 13 GB

  Number of guests: 2

  Total processors: 6

  Number of Virtual Machines: 4

  The migration total: 0

  Admission control: do not allow any violations of constraints

  The current failover capacity: 0

  Ability to failover configured: 1 host

  DRS

  Automatic migration of level: partially automated

  Power management: Off

  Level of automation:

  Recommendations of the DRS: 0

  Migration threshold: the recommendations with 3 stars or more

  Of ' Host1: Summary tab.

  CPU use 2816 MHz off (2 x 2.784 GHz) 5,568 GHz

  Use 537,00 in fees MB memory on (5.75 GB)

  Host1 VM1 Configuration

  • Memory 2048 MB

  • CPU2

  To "Host2: Summary tab.

  CPU use 1453 MHz off (4 x 1,866 GHz) 7,464 GHz

  Memory usage 2.43 GB on (7.0 GB)

  Host2 VM1

  • 748 MB of memory

  • CPU 1

  Host 2 VM2

  • Memory 1024 MB

  • CPU 1

  Host 2 VM3

  • Memory 1024 MB

  • CPU 1

  ________________________________

  It is sometimes much easier point to this article, it is very well implemented.

  Please consider awarding points by scoring responses like 'correct' or 'useful '.

• Failover Standby DB error

  Hello.
  I tried to make a process of failover in a database of the previous day. On the ARCH directory, I have the last archived file ARCH_126983.arc
  
  Yes, I did
  SQL > alter database base_de_donnees eve of Mount;
  SQL > recover database auto sleep;
  Cancel
  (He has recovered to the ARCH_126983.arc)
  
  SQL > SHUTDOWN IMMEDIATE;
  SQL > alter database base_de_donnees eve of Mount;
  SQL > alter database open read-only.
  SQL > alter database recover managed standby database finish;
  
  ALTER database recover managed standby database finish
  *
  ERROR on line 1:ALTER of database DATA RECOVER MANAGED STANDBY DATABASE FINISH SKIP STANDBY LOGFILE;
  ALTER DATABASE RECOVER MANAGED STANDBY DATABASE FINISH SKIP STANDBY LOGFILE
  *
  ERROR on line 1:
  ORA-00283: cool cancelled due to errors
  SQL > ALTER DATABASE RECOVER MANAGED STANDBY DATABASE FINISH;
  ALTER DATABASE RECOVER MANAGED STANDBY DATABASE FINISH
  *
  ERROR on line 1:
  ORA-00283: cool cancelled due to errors
  ORA-16171: RECOVER... FINISHING not allowed away for thr 1, seq 1-126983
  
  SQL > ALTER DATABASE RECOVER MANAGED STANDBY database finish skip;
  ALTER DATABASE RECOVER MANAGED STANDBY database finish skip
  *
  ERROR on line 1:
  ORA-00283: cool cancelled due to errors
  ORA-00342: archived log was created before last RESETLOGS
  ORA-00334: archived log: ' / u01/app/oracle/admin/auth/arch/ARCH_0.arc'
  
  ________________________________________________________
  
  Then in which instruction failover adds a marker to end-of-redo the last archived log file header. Why repeat the sequence in the archived file has been reset from 126983 to 1?
  
  I use not DataGuard management relief. And my Oracle version is:
  
  SQL > select * from v version $;
  
  BANNER
  ----------------------------------------------------------------
  Oracle9i Enterprise Edition Release 9.2.0.8.0 - 64 bit Production
  PL/SQL Release 9.2.0.8.0 - Production
  CORE Production 9.2.0.8.0
  AMT for HP - UX: 9.2.0.8.0 - Production Version
  NLSRTL Version 9.2.0.8.0 - Production
  
  
  
  How can I change this mode database role ensures the primary, but without transition process (I guess that the primary is not accessible).
  
  Thanks for any help.

  Yes, as you can see now the database_role is the principal, so you did the failover.

  ALTER DATABASE COMMIT AT THE GRADE CROSSING;

  Is used when you want to make the transition to digital and switchback, not tipping. You can ignore the error.

  For the revival of the command is:-alter database activate standby database;

  Anand

• spectrum x 360: "hp has encountered an error when trying to analyze your product."

  whenever I try to identify my phone it says "HP has encountered an error when trying to analyze your product."

  Why is it so? is there anyway around it? I know that you can manually enter your product, but I was curious to see how it would work.

  Infrastructure solutions from HP support is a mandatory program.

  This product detection tool installs the software on your Microsoft Windows device that allows HP to detect and collect data on your HP and Compaq products to provide fast access to support information and the solutions. Technical data are collected for products supported by this tool and are used to identify products, offer solutions relevant and automatically updated on day of this tool, in order to improve our products, solutions, services and your experience as our customer.

  Note: This tool applies only to Microsoft Windows PC. This tool detects computers HP and HP printers.

  Data collected:

  • Operating system
  • Version of the browser
  • Computer dealer
  • Product name/number
  • Serial number
  • Connection port
  • Description of the driver/device
  • Computer configuration / printer
  • Hardware and Software Diagnostics
  • Ink HP/Non-HP or Non-HP/HP Toner cartridges
  • Number of printed pages

  Details of the installed software:

  • HP Support Solutions Framework - Windows, localhost Web Server Service and software

  Remove installed software:

  • Remove "HP Support Solutions Framework" via Add/Remove programs on PC

  Requirements:

  • Operating system - Windows 7, Windows 8, Windows 8.1, Windows 10
  • Browser - Google Chrome 10 +, Internet Explorer (IE) 10.0 + and Firefox 3.6.x, 12.0 +.

  You can try to disable adblock and adblock plus and see that he would invite you to install the software.

  In case you are still unable to download the software, I downloaded the software on HP Dropbox.

  HTTPS access: https://ftp.usa.hp.com/hprc

  FTP access: ftp://hpssf:^[email protected]

  Drop box host: ftp.usa.hp.com (15.73.40.56, failover: 15.73.244.52)

  Login: hpssf

  Password: ^ YHN9ol.  (NOTE: case sensitive)

  Account Expires: 24/02/2016-17:09:31 (drop box date expiration/deletion)

• Windows Vista SP1 error: 0xc0190036 (kernel32.amx)

  I tried to install SP1 on Windows Vista Ultimate 32-bit, like, forever now.

  He receives through steps 1 and 2 with no problems, then restarts the computer and begins to display all the registry files, etc., and then it freezes on:

  !! 0xc0190036! 4125/96829 (kernel32.amx)

  I have the voltage to the computer, then it will automatically load the Startup Repair.  In general I just do a system restore and live with all other errors (browser crashes, program freezes and incompatabilities, etc.) who accompany him not not upgrade, but now I really want to get this resolved.

  I kernel32.amx in C:\Windows\System32\manifeststore and tried to replace, rename, or delete, but I get an error message saying that I need permission to do so (even if I am logged in as the only administrator on this model). It is not read-only. I can't find it in the processes running in the Task Manager.  I am not even sure, however, if I look at the right file (are there other files named kernel32.amx?).

  I restarted Windows Mode without failure, but it's the same thing.  When I tried to reinstall SP1 & got the same error, I launched the Startup Repair and chose to not not to do a system restore immediately.  It generated the report to Microsoft:

  Problem event name: Startup Repair V2
  Signature of the problem 01: Auto failover
  Signature of the problem 02: 6.0.6000.16386.6.0.6001.18000
  Signature problem 03: 1
  Signature of the 04:65537 problem
  Signature of the problem 05: unknown
  Signature of the 06 problem: BadPatch
  Signature of the problem 07:0
  Signature problem 08:3
  Signature of the problem 09: WrpRepair
  Signature of the 10:10 problem
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  I clicked on "View diagnostic and repair details" and he showed several tests that have been carried out; most were successful, but a few lines in this report seems relevant:

  Root cause found: a patch prevents the system to start
  Repair action: repair and checking the integrity of system files
  Result: failed. Error code = 0xa

  I went to the Advanced System Recovery Options, but apparently I'm not that advanced. I ran Windows memory diagnostic tool (which found no errors, but also does not generate a report), then re-run Startup Repair, which has generated a new report to be submitted to the slightly different Microsoft:

  Problem event name: Startup Repair V2
  Signature of the problem 01: Auto failover
  Signature of the problem 02: 6.0.6000.16386.6.0.6001.18000
  Signature of the problem 03: 6
  Signature of the problem 04: 196611
  Signature of the problem 05: CorruptVolume
  Signature of the 06 problem: BadPatch
  Signature of the problem 07:0
  Signature problem 08:3
  Signature of the problem 09: WrpRepair
  Signature of the 10:10 problem
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  Finally I just did a system restore to the last restore point. It is here where I am now. Any ideas?  I'm looking in the right places?

  Hi Didigrn,

  You got the error message indicates that kernel32.amx is damaged and there is one possibility of other files system is corrupted as well. All what we need to do is to rename the DLLs corrupted, restart the computer and let start the computer normally to complete the installation. Follow these steps to rename the corrupted dll file.
  (1) Insert the windows vista dvd and boot from the dvd.
  (2) select repair your computer.
  3) click on command prompt.
  Type the following commands and press ENTER after each line
  C:
  CD windows
  CD system32
  Ren kernel32.amx kernel32.amx.old
  (4) output of command line.
  (5) restart the computer and boot up normally.

  If you GET the black screen with a similar error and another file (except kernel32.amx), take note of the dll file, repeat steps 1 to 5 and type the name of the file in step 3.

  Restart the computer. It may take a while and you will be asked to connect to the desktop computer.

  Check in system properties if SP1 is installed or not.

  I hope this works. If you still have problem please after return.

  Shalini
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "The [ComputerName] has no installed feature of failover clustering. Use Server Manager to install the feature on this computer. "

  Hello

  I got this error message prompt to try to add the first node, by which I already have installed in the node 1 and node 2 failover function. I am running windows server 2008 standard version at the moment and have all the grouping necessary setting such as: joined the domain, shared disk and etc. Facing this problem when trying to run/validate configurations "failover cluster management.
  Kindly, advice
  Boonlep coulibaly

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:
  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• FPGA reference questions between the station development and execution? 63195 error code

  I will do my best to describe the problem, I was see.  Note, I tried a few other messages that kind of touch on my problems, but they never seem to have a definitive solution.

  Background-

  I have 3 screws:

  VI 1) opens / runs the bitfile FPGA reference and stores the reference to a global file so that I can call the reference of other screws I need to do this as opposed to the opening of a new reference because I use the FPGA for digital communications and it adds about 100 ms to to open a new reference whenever I need to read/write in the target FPGA to host (100 ms are long in the) digital world!).  Some people use Shift Registers.  I finally called my whole army FPGA screws of TestStand to run a test automated, so it was easier to break up of my functions for open/close/read/write.

  VI 2) called the global reference of the file for FPGA, then going to a read/write node to change the settings of the target, then passes the reference out of the node back to the global reference of the file read/writable

  VI 3) calls close reference FPGA and the function is passed the global reference of the file.

  Question-

  I understand not why this method works fine when I run either of TestStand with station options defined for the development (not running) mode or when I open VI which calls these 3 screws individually in sequential order but IS NOT working when I try to run these screws individually (Run VI 1 - open-> write Ref to the global reference of the file-> Run VI 2 - read global file reference-> playback control function / writing-> error-63195) or when I have run in the same sequence TestStand but together with station for execution options.  Maybe I need to change the TestStand sequence to load all the modules at startup?

  Why the reference becomes lost when global failover between development and execution and why labview cannot drop keep the reference stored?  Is there a work around?

  Finally found a solution.  I do not understand why it is necessary during the reading of the FPGA and not what writing (in fact I do not understand why it worked at all) but I ended up changing the properties of the step in my TestStand sequence for the step calling my DTL_READ.vi to be properties-> Run Options-> Unload Option-> "Unload after executing the step.  That seemed to do the trick to get my test TestStand sequence to work in runtime.

  I still don't understand why this was not required when you run the same sequence in the design environment and why it is not when I call my DTL_WRITE.vi.

  The DTL_READ.vi and the DTL_WRITE.vi pass the parameter labveiw global.vi 'Reference FPGA VI"of a node in read/write.  I don't know if the root of the problem is in my host TestStand and LabView FPGA VI...

  Thanks for all suggestions from you guys!  I'm happy I work but I am still confused by the solution.

• Acer eRecovery error Flash...

  Hello

  I paid $80 for delivery the next day on a flash for my laptop Acer eRecovery.   And when I pasted into my USB a mistake came about 5 minutes in the process, saying: "M:\NAPP.dat is Miss.".   I can't complete the process of resetting my computer laptop back to factory settings.  I'm in Windows 8.

  How can I get this error and get things on my work laptop once more?

  Thanks in advance.

  I think it was a combination of failover to the legacy access to the hard drive and using an old recovery flash drive to format completely with Iso in one other usb hub to finally allow the new usb acer create records of M and N necessary for the new installation. Thank you

• Automatic failover cluster Bugging head

  Hi all

  I am faced with continuous cluster due to network problem failover. I have two cluster CLUS1 and CLUS2, he got automatic failover cluster if all resources being normal. The error description is as follows: -.

  Event type: Information

  Event source: vxio

  Event category: no

  Event ID: 29

  Date: 2010-09-27

  Time: 07:23:38

  User: n/a

  Description:

  vxio: disk driver returned the error 80000011 when vxio tried to read block 2222998 on Harddisk89.

  I don't know, it's always because as the high utilization of the processor on a particular server or what. We have done several successful and trails w.r.to SAN, memory and performance optimization, but everything seems OK but even we in the face of this failover as a routine and fine.

  Can you suggest me on the subject that... What all could be the possible reasons for this.

  Better suggest me the solution from your end.

  Also any suggestions and comments in brackets

  + Is the place pilot a gradation is a possible solution? [Even it will not be successful on one of the test of trail]

  + Increase SAN can be the solution? [Sufficient SAN is already there that again I ask]

  + Or memory problem? [Same memory is sufficient to perform the work]

  + It is not particularly over a certain period, as at the end of week or Monthened.

  This shift has become a routine job, same everything seems fine? Please advise suggest his irritates my head a lot.

  Hi VenOMCM,

  The issue of Windows XP, you have posted is better suited for the IT Pro TechNet public. Please ask your question in the TechNet forums for assistance.

  Hope the helps of information.

• Error MD3220i MPIO

  I have a virtual data center consisting of two windows server 2012R2 hyper-v hosts Manager connected to a MD3220i of basic failover cluster running.

  Everything looks good, except on a single host, I get the following error from MPIO in the windows event logs:

  Event ID: 32

  Reference Dell MD series Module specific to the device for Multi-Path does not have a pathway back to \Device\MPIODisk0.

  These events come in several times a day, and they occur for all 3 disks in the system.

  MDSM reports no errors

  All paths are available in iscsicpl.

  Apart from this error, everything looks good.  I have about 10 Vm running on the SAN, clustering with failover and migration to run without problem.  I am ready to put the system into production, but I would like to know why I'm getting this error before to do so be sure that there are no underlying problems.  I did find something specific to the error online, so I thought I would ask here.  If anyone can point me in the right direction that would be great.

  Thank you

  Hey, Madendever.

  I should have said from the very beginning. It is best to uninstall completely, (it might even be a good idea to go in the programs directory and delete its files and leftovers from the previous installation) style 'old school') and re-install the application. I saw it several times where something click until it's done.

  Also, I would be sure that you use the most recent iso for MDSM.

  I know it sounds like a 'nit - pic', but I have seen too many times to not judged.

  If this is not yet it solves, let me know.

• EqualLogic group member network configuration error: "management interface should not be on the san subnet.

  Hello

  We currently have new EqualLogic 6100 device with this network configuration:

  Director of the IP - 192.168.0.2 (VLAN1).

  Member network config:
  eth0 - 192.168.0.3 (VLAN1)
  eth1 - 10.10.10.3 (VLAN2)
  eth2 - 10.10.10.4 (VLAN2)
  eth3 - 10.10.10.5 (VLAN2)
  ETH4 - empty

  I would attribute 192.168.0.4 to eth4, but received the error: "management interface should not be on the san subnet.

  I am sure that all interfaces eth has access to the VLAN1 and VLAN2, mean error indicates that eth4 should not access VLAN2 and only access the VLAN1 on the switch?

  Or eth0 should also have access to the VLAN2 only to reconfigure eth0 and eth4?

  Thank you

  > The group eating IP should be in iscsi VLANS?

  Yes!

  Note: If configure you an EQL it will ask an iSCSI port because nothing is more necessary to bring it up. The doest previous EQLs have a dedicated Mgmt Port and later, you can convert the last ethX as a MGMT port. This is the reason why configure you ISCSI at the beginning. (Think of a mixed group of newer and older models, and you get a picture)

  OK... once again it is the one and only member of the Group and there is making the production host connected to the right?

  The change of IP address, to a 3rd. subnet for temporary use.

  -Do not touch eth0-3 and the IP address of the group now

  -Configure the MGMT port and IP address management in the tempr group. Subnet. Use the Config-> Adv. Group-> network MGMT. You can change the MGMT Port of the Member, and the address IP of MGMT

  -For the registration of the configuration, you will lose access. You must place your admin PC in the templ. subnet so

  -Connect to the GroupMgr with temp again. INTELLECTUAL PROPERTY

  -Now you can change the IP address of group 10.10.10..x

  -Now you can change eth0 10.10.10.2

  -At the end, you can change the address IP of the Group MANAGEMENT, as well as the MGMT Port to 192.168.0.x

  -Change the IP address of your admin PC rear

  A failover, you should consider to hang a serial cable the active controller of the EQL. Use 9600,8,1, N with your favorite terminal program (putty.exe on windows). All the steps, you can perform from the command line.

  If this group and the only member not in production, but you can reset the config and restart from the beginning.

  Kind regards

  Joerg

• Storage array error event (PS4100X)

  Dear Sir, I have VMwaer Vsphere 5.5 x 2 and only switch and DELL PS4100X storage I don't know why, I'm wearing the messeage PS4100X like this form = the table eql-1 storage subsystem ERROR event: event SP [secondary]: 15.4.1 time: Fri Jul 25 11:52:10 2014 NVRAM contains valid data. It is a RECOVERY of PANIC because of the panic on a processor of NetBSD. -Event of the table eql-1 storage subsystem ERROR: event SP [secondary]: 15.4.5 time: Fri Jul 25 11:52:10 records of 2014 saves CPU, CPU 1 to 0000000000000000 0000000004010000 v0 v1 ffffffffbef08010 a0 0000000000000104 a1 a2 a3 0000000000000000 0000000000000104 ffffffffd2243b70 t0 0000000000000001 t1, ffffffffd2243b70 t2 ffffffff804e2f88 t3 t4 0000000000000001 ffffffff8041f1d0 t5 0000000000001000 t6 0000000033de3e40 t7 0000000033de4290 s0 ffffffff8098b718 s1 ffffffffd2243b70 s2 ffffffff8098b718 s3 s4 0000000000000000-0000000000000000 s5 s6 0000000000000000 ffffffff82c84e60 s7 ffffffffc0131000 t8 t9 0000000000000000-0000000000000000 k0 k1 000000000010849f gp ffffffff80033000 000000000010845f SP ffffffffd22439e8 S8 ffffffff80976cf8 ra ffffffff804d2cac - the table eql-1 storage subsystem ERROR event: event SP [secondary]: 15.4.6 time: Fri Jul 25 11:52:10 2014 saved CP0 registers, CPU 1 sr 00488005 badva c01320a0 EPC 806a2ba0 errorepc 804d2c80 cause 00000108 errctl 00000000 cacheeri 00000000 cacheerd 00000000 buserr 0000000000000000 cacheerrdpa 0000000000000000 - ERROR event of the table eql-1 storage subsystem: SP [secondary] event: 15.4.7 time : Fri Jul 25 11:52:10 function call 2014 saved battery, CPU 1 804d2c80 804d2cac 804d2e90 806d99e0 804e2e88 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 80697a 38-= can you tell me why? Please HELP Storage control F/W is V6.0.8

  We installed VMware Tools in all virtual machines and have also a good configuration of switch for our ESXi hosts tolerate the 10 sec 'dead time' of the connection of storage. Controller failover takes less than 10 seconds here and only 4 pings are missed.

  We do FW updates in a low period of IO. I have to manage 25 EQLs and we carry out the FW update without blocking down the cluster. I have disable HA 'Host followed' as well as the notification by e-mail from vCenter for the time.

  Yes version 7.0.5 is the latest public version available. 2 days ago, the FW Drive Kit 5.0 comes out so you can take one taken if your drives are on the list. If so, update the first readers.

  Yes, as readers can be improved without closing anything. Drive for affected car kit checks and do one after the other.

  Yes, you can upgrade directly from 6.0.8 7.0 x

  You will see the service tag to the title of Member-> maintenance in the EQL Groupmanager. Go to dell.com and support and see if you have a support contract is valid. Check www.dell.com/.../Contact-Information how to contact Dell technical support. If nothing is done, use the support link after you connected to https://eqlsupport.dell.com

  Kind regards

  Joerg

• Request support by MD3220i - error cluster [CF]

  Buon giorno, US vs riscontro gentile e di assistenza in merito al evento following preventivo:

  The infrastruttura e nostra composed da UN MD3220i con 3 host due e R610 PowerConnect 2848 switch, da some giorno a perdere instradamento verso gli hanno begun the host Announces where the MD3220i.

  Da una prima disgnostica di message following sulla MD abbiamo rilevato it 'alert ':

  Date/time: 08/01/16 8.26.31
  Sequence number: 41599
  Type of event: 4011
  Event category: error
  Priority: critical
  Description: Virtual disk not a being preferred due to the AVT/RDAC failover
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: enclosure 0, Slot 1
  Recorded by: Module to slot 1 RAID controller

  Raw data:
  4 d 45 a2 7f 48 03 00 00 00 00 00 00 00 00 00 4 c
  11 40 18 01 97 eb 57 00 00 00 00 00 00 00 00-9F
  00 00 00 00 01 00 00 00 22 00 00 00 22 00 00 00
  08 00 00 00 00 00 00 00 02 00 00 00 01 00 00 00
  0 a 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  01 00 00 00 00 00 01 00 00 00 00 00

  We have tried a curare infrastruttura MD, host switch e spegnere.

  After the riaccensione he message di "alert" su e scomparso totally, senza più particular if MD, recoupling outdo degli host verso MD3220i risultava Semper ad where con conseguente perdita accesso alle cartelle di rete e macchine virtuali.

  Host No. 2 dei R610 abbiamo quindi con spento 3 he risultato che dopo d manuale da console del servizio cluster it sistema e partito a funzionare senza problemi di comunicazione più correctly.

  Lato host abbiamo rilevato che some door ISCSI MD non sono più ragiugibili del (nello specifico n ° 1 of the castroni sono no door porta del MD3220i controller)

  The VLAN non sono state modificate e lato PowerConnect 2848 switch if not rilevano if.

  Current location: MD3220I senza if a host adapter solo di n ° 3 access.

  Company di MD3220i:

  He prodotto e stato nel 2010 labor-intensive, co del prodotto e scaduta it 13/12/2015.

  Re: MD3220i fuori co serial number F1QGY4J

  Buongiorno, the sto contattando by mail.