Similar Questions

• MD3200i with 2012 multipathing not correctly

  Hello

  I had a MD3200i as the CSV storage for a cluster of data center 2012 running on 4 network cards between the host and a switch to two controllers. I updated the firmware and used the latest DVD for installation in 2012.

  When I did the installation I used the button "Recommended" to create sessions and connections. Everything seemed to go well in the tests.

  However, now the system is power on I see that traffic is not balanced on the NICs, but simply all come from a NIC to the extent where this NIC 1 used 560MBps for 30 minutes without other network cards get about 30 kbps.

  Is there something I need to do to enable Multipath? Or have I misunderstood what it is supposed to do? It's just for a failover, rather than load balancing?

  Thanks and greetings

  Andrew Smith.

  If anyone is interested, this is the answer.

  faultbucket.ca/.../MD3220i-MPIO-Driver-Install-on-Hyper-v

• PowerVault MD3220i error (insufficient ability to backup device Cache)

  Hi all

  I appreciate your time and assistance with the following question.

  I recently upgraded to the latest firmware on my HP MD3220i and installed the corresponding update of the NVRAM.

  After you install the update, I get the following error in MDSM.  I checked the cache backup capacity and the total used the two related 1 680 MB.

  Is there a reason that the error occurs and what is the best approach to fix this problem?

  I checked the forums but don't see anything specific in addition to replace the module or the upgrade of cache memory.  Otherwise, the device works without problem, but like most of you, I hate this clear amber flashing in a data center perfectly Blue :)

  Thank you!
  Omar

  Ability of the insufficient Cache backup device

  Hello, Omar.

  This error has been research. In all cases this error is visible by our technicians of telephone, the RAID controller is replaced.

  After talking to some experienced engineers, I would recommend replacing this controller.

  This error can occur either bad shutting down the table leading to a corruption of the meta-database backup, or the stick (a small SD card) cache could be dethroned.

  You * can * try to remove the controller, wait that the "power run" for draining, reinstall the cache memory card and then put it back in the slot. Who can clear this error, but no promises. However, we do not replace the cache card herein. The only thing that replace us inside the controller's battery.

  I hope that helps you out. Let me know if you have any questions.

• Request support by MD3220i - error cluster [CF]

  Buon giorno, US vs riscontro gentile e di assistenza in merito al evento following preventivo:

  The infrastruttura e nostra composed da UN MD3220i con 3 host due e R610 PowerConnect 2848 switch, da some giorno a perdere instradamento verso gli hanno begun the host Announces where the MD3220i.

  Da una prima disgnostica di message following sulla MD abbiamo rilevato it 'alert ':

  Date/time: 08/01/16 8.26.31
  Sequence number: 41599
  Type of event: 4011
  Event category: error
  Priority: critical
  Description: Virtual disk not a being preferred due to the AVT/RDAC failover
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: enclosure 0, Slot 1
  Recorded by: Module to slot 1 RAID controller

  Raw data:
  4 d 45 a2 7f 48 03 00 00 00 00 00 00 00 00 00 4 c
  11 40 18 01 97 eb 57 00 00 00 00 00 00 00 00-9F
  00 00 00 00 01 00 00 00 22 00 00 00 22 00 00 00
  08 00 00 00 00 00 00 00 02 00 00 00 01 00 00 00
  0 a 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  01 00 00 00 00 00 01 00 00 00 00 00

  We have tried a curare infrastruttura MD, host switch e spegnere.

  After the riaccensione he message di "alert" su e scomparso totally, senza più particular if MD, recoupling outdo degli host verso MD3220i risultava Semper ad where con conseguente perdita accesso alle cartelle di rete e macchine virtuali.

  Host No. 2 dei R610 abbiamo quindi con spento 3 he risultato che dopo d manuale da console del servizio cluster it sistema e partito a funzionare senza problemi di comunicazione più correctly.

  Lato host abbiamo rilevato che some door ISCSI MD non sono più ragiugibili del (nello specifico n ° 1 of the castroni sono no door porta del MD3220i controller)

  The VLAN non sono state modificate e lato PowerConnect 2848 switch if not rilevano if.

  Current location: MD3220I senza if a host adapter solo di n ° 3 access.

  Company di MD3220i:

  He prodotto e stato nel 2010 labor-intensive, co del prodotto e scaduta it 13/12/2015.

  Re: MD3220i fuori co serial number F1QGY4J

  Buongiorno, the sto contattando by mail.

• MPIO iSCSI error

  I downloaded and installed vSphere 4 and found a tutorial on the configuration of MPIO.  I encountered an error when I try to add network cards to the swiscsi.

  esxcli swiscsi nic add - n vmk1 d vmhba35

  "Add Nic failed in IMA."

  I followed the instructions to the following ADDRESS, and it seems that someone has experienced this problem.  We do not use the distributed switch again.  It's just a stand-alone host without vCenter again.

  http://www.yellow-bricks.com/2009/03/18/iSCSI-Multipathing-with-esxcliexploring-the-next-version-of-ESX/

  Anyone run into this and found a solution?

  I thank very you much for any help.

  Move the 'other' NIC mode ensures unused. That should do it. You'll failover anyway since you have more than one path.

• Ping on MD3220i error

  Hello

  I'm trying to set up a unit of SAN MD3220i.

  I use IP addresses by default for each port iSCSI on controller 0 and 1 controller.

  I installed my host (Hyper-V Server 2008 R2) and I use 2 network cards for SAN traffic on this host, the IP addresses that I've assigned are 192.168.130.3 (255.255.254.0) and 192.168.132.3 (255.255.254.0)

  Each NETWORK adapter is connected via a separate to the San switch.

  When I ping to each of the 4 SAN ip addresses, only 2 answer, these are 192.168.130.101 and 192.168.132.101.

  Why the other two IPS (192.168.131.101 and 192.168.133.101) without responding to the ping request.

  All on the ports of SAN subnet masks are 255.255.255.0

  Thanks for your help

  Hi Sam,

  Sorry for the delay, I've tried a few things and was able to solve the problem.

  The SAN comes with default subnet masks 255.255.255.0 on all iSCSI ports, but I put my NIC host having 255.255.254.0 subnet masks.

  Once I changed to 255.255.254.0 SAN subnet masks I could ping all of the 4 ports on the host channel.

  Thanks a lot for helping me with this problem.

• MD3220i lock problem

  Hi all

  We have a strange problem with the md3220i.

  The system is brand new, we opened the packages and the power of the system, but we have something strange with the newspapers. We cannot communicate with the controller. That's what we see in the papers:

  How to solve this problem, do you have any ideas?

  -=<###>=-
  Instantiation of RAM rawfs, peripheral = 0 x 1
  RAM DOSFS formatting
  Instantiation of RAM rawfs, peripheral = 0 x 1
  Formatting... Params volume consulted old 38% trust:
  Volume settings: FAT type: FAT32, sectors per cluster 0
  0 copies FATS, groups 0, 0 sectors per FAT
  Areas reserved 0, hidden 0, FAT sectors 0
  Root dir entries 0, (null), serial number 10000 sysId
  "Label:" «...» "
  Drive with 1024 sectors of 512 bytes will be formatted with:
  Volume settings: type FAT: FAT12, sectors per cluster 1
  2 copies FAT, clusters of 1010, 3 sectors per FAT
  Areas reserved 1, hidden 0, FAT sectors 6
  Root dir entries sysId 112, VXDOS12, serial number 10000
  "Label:" «...» "
  Instantiation of RAM rawfs, peripheral = 0 x 1
  Ok.

  RTC error: Device real-time clock does not work

  Autonomous 13884 symbols added.
  Length: 0x13c bytes
  Version ver03.0A

  Reset, Power-Up Diagnostics - loop 1 1
  Processor 3600 DRAM
  Data lines 01 Passed
  Address lines 02 Passed
  NVSRAM 3300
  Data lines 01 Passed
  4410 Ethernet 1 82574
  01 registry read Passed
  Address lines 02 registry Passed
  6 d 40 Bobcat
  02 flash test passed
  3700 PLB SRAM
  Data lines 01 Passed
  Address lines 02 Passed
  7000 TO iSCSI BE2 1
  01 registry read successful Test
  02 registry address lines Test passed
  Rows of data from registry 03 test passed
  3900 real-time clock
  01 RT Clock Tick past
  Diagnostic Manager came out normally.

  Current date: 15/01/14 time: 01:43:59

  Send Change Service Interface rate or baud
  15/01/14-09: 00:05 (NCDB): NOTE: set the Powerup State
  15/01/14-09: 00:05 (NCDB): Normal sequence SOD, the 0 on controller
  15/01/14-09: 00:05 (NCDB): NOTE: turn on seeing failure summary tray
  15/01/14-09: 00:06 (NCDB): NOTE: installed protocols:<>
  PS: RDMA ISER IPOIB >
  15/01/14-09: 00:06 (NCDB): NOTE: the required protocols:<>
  UNK >
  15/01/14-09: 00:06 (NCDB): NOTE: loading of the flash file: iSCSI
  15/01/14-09: 00:08 (NCDB): NOTE: DSM: current revision 7
  15/01/14-09: 00:08 (NCDB): NOTE: SYMBOL: SYMbolAPI registered.
  15/01/14-09: 00:08 (NCDB): NOTE: the total size of the Patriotic Army Rwandan RCBBitmapManager = 1778384896
  15/01/14-09: 00:09 (NCDB): NOTE: in iscsiIOQLIscsiInitDq. iscsiIoFstrBase = x 0
  1
  15/01/14-09: 00:09 (NCDB): NOTE: loading of the flash file: MTLSEBET1G
  Disabled the COMPLETE TRACE *.
  15/01/14-09: 00:09 (NCDB): WARN: MTLSE: before size special mtl_create_pool:IO: 0 x
  140
  15/01/14-09: 00:09 (NCDB): NOTE: init: IOC: 0, PLVersion: 11-03-075-00
  15/01/14-09: 00:10 (NCDB): WARN: MLM: failed to create m_MelNvsramLock
  15/01/14-09: 00:10 (NCDB): WARN: MLM: failed to create m_MelEventListLock
  15/01/14-09: 00:10 (NCDB): NOTE: CrushMemoryPoolMgr: platform and memory (CPU M
  emSize: 2048), adjusted allocation size to 65536 for CStripes
  15/01/14-09: 00:12 (NCDB): SOD: instantiation Phase complete
  15/01/14-09: 00:11 (IOSched): NOTE: SAS Expander added: expDevHandle:x 11 enclHan
  DLE:x 2 numPhys:37 port: 2 ioc:0 channel: 0 numEntries:22
  15/01/14-09: 00:11 (NCDB): WARN: sodLockdownCheck: sodSequence update: CtlrLock
  down
  15/01/14-09: 00:11 (NCDB): caution: any attempt to open the inter communication controller
  communication channels 0-0
  15/01/14-09: 00:11 (NCDB): NOTE: LockMgr role is master
  15/01/14-09: 00:12 (tSasExpChk): NOTE: Local Expander Firmware Version: 00.00.80
  .10
  15/01/14-09: 00:18 (tSasDiscCom): NOTE: SAS: full time of Initial discovery: 36
  seconds since the last power on / reset, 10 seconds since the instantiated sas
  15/01/14-09: 00:18 (NCDB): NOTE: baseName WWN 000290 b 1-1c1190ee (valid ==> SigMat
  ch)
  15/01/14-09: 00:18 (NCDB): NOTE: spmEarlyData: no data available
  15/01/14-09: 00:18 (NCDB): NOTE: 2 Ut ServerEngines BladeEngine Firmware update
  m v2.901.242.0
  Copyright 2009 ServerEngines Corpo
  15/01/14-09: 00:18 (NCDB): NOTE:
  15/01/14-09: 00:18 (NCDB): NOTE: found card BE 0 x 0 to 2.0 bar1-base 0xf0200000
  bar2-base 0xf0220000 dev 0x384292c
  15/01/14-09: 00:18 (NCDB): NOTE: flash_rbver = 2.0.3.768
  15/01/14-09: 00:18 (NCDB): NOTE: flash_armfwver = 2.901.319.0
  15/01/14-09: 00:20 (NCDB): NOTE: ufi_rbver = 2.0.3.768
  15/01/14-09: 00:20 (NCDB): NOTE: ufi_armfwver = 2.901.319.0
  15/01/14-09: 00:20 (NCDB): NOTE: Flash on BladeEngine at 02:00 corresponds to UFI
  BE2T1G
  15/01/14-09: 00:20 (NCDB): WARN: MTLSE: start: lowLevelInit target bcmId: 0 ins
  tId 0
  15/01/14-09: 00:20 (NCDB): NOTE: irq_ptr:0xd78850
  15/01/14-09: 00:20 (NCDB): NOTE: BcmId [4] PCI [2.0.4]
  15/01/14-09: 00:20 (NCDB): NOTE: DFR 0 x 0212 VendId 0x19a2
  15/01/14-09: 00:20 (NCDB): NOTE: IO BAR0 base 0xf0380000
  15/01/14-09: 00:20 (NCDB): NOTE: BAR1 MEM base 0xf03a0000
  15/01/14-09: 00:20 (NCDB): NOTE: BAR2 MEM base 0xf03c0000
  15/01/14-09: 00:20 (NCDB): WARN: MTLSE: fact: with the initialization of the initiator: mt
  Lint: 0x526fbc0 target bcmid:0 init bcmid: 4 rc 0, phba:0 x 5270020
  15/01/14-09: 00:20 (NCDB): NOTE: target: irq_ptr:0x0xd780b0, func:0 0, bcmId:0 0 x x

  15/01/14-09: 00:20 (NCDB): NOTE: VendorID, DeviceId 0x19a2 0 x 210 bcmId BDF 2.0 0
  .0
  15/01/14-09: 00:20 (NCDB): NOTE: target: VKI_INT_CONNECT success: status: 0x0
  15/01/14-09: 00:20 (NCDB): ERROR: target: SRI registered: irq_ptr:0xd780b0, phba:0
  x383fca0, func:0 x 0
  15/01/14-09: 00:20 (NCDB): NOTE: BcmId [0] PCI [2.0.0]
  15/01/14-09: 00:20 (NCDB): NOTE: DFR 0 x 0210 VendId 0x19a2
  15/01/14-09: 00:20 (NCDB): NOTE: BAR0 e/s of basic size 0x00000000 0
  15/01/14-09: 00:20 (NCDB): NOTE: BAR1 MEM base 0xf0200000 size 1
  15/01/14-09: 00:20 (NCDB): NOTE: BAR2 MEM base 0xf0220000 size 1
  15/01/14-09: 00:20 (NCDB): NOTE: BAR4 MEM base 0xf0240000 size 1
  15/01/14-09: 00:20 (NCDB): NOTE: MPU_EP_SEMAPHORE 0x0000c000
  Driver Build Date: Oct 25 2012, time: 15:03:42
  ServerEngines iSCSI Target driver loaded
  iSCSI Firmware Version: 2.901.319.0
  iSCSI Driver Version: 2.901.242.0
  Found BladeEngine2 in Gen2 x 8 PCIe slot
  15/01/14-09: 00:21 (NCDB): NOTE: region memory of Rwandan Patriotic Army: start 0x47392fe00 size 167
  77216 (ConIO-size 16777216) recorded for the pre-post on port 0 data buffers
  15/01/14-09: 00:21 (NCDB): WARN: MTLSE: default link on the interface-local address
  1 is fe80:0000:0000:0000:92 1 b: 1cff:fe37:7 b 41
  15/01/14-09: 00:21 (NCDB): WARN: MTLSE: default link on the interface-local address
  5 is fe80:0000:0000:0000:90 1:1 c 03 b: e837:7 b 41
  15/01/14-09: 00:22 (NCDB): WARN: MTLSE: default link on the interface-local address
  6 is fe80:0000:0000:0000:90 1:1 c 07 b: d037:7 b 41
  15/01/14-09: 00:22 (NCDB): WARN: MTLSE: fact: with the initialization of the target: 0 rc
  0
  15/01/14-09: 00:22 (NCDB): WARN: MTLSE: fact: lowLevelInit bcmId: 0 rc 0
  15/01/14-09: 00:22 (NCDB): WARN: MTLSE: start: lowLevelInit target bcmId: 1 ins
  tId 1
  15/01/14-09: 00:22 (NCDB): NOTE: irq_ptr:0xd78668
  15/01/14-09: 00:22 (NCDB): NOTE: BcmId [3] PCI [2.0.5]
  15/01/14-09: 00:22 (NCDB): NOTE: DFR 0 x 0212 VendId 0x19a2
  15/01/14-09: 00:22 (NCDB): NOTE: IO BAR0 base 0xf03e0000
  15/01/14-09: 00:22 (NCDB): NOTE: BAR1 MEM base 0xf0400000
  15/01/14-09: 00:22 (NCDB): NOTE: BAR2 MEM base 0xf0420000
  15/01/14-09: 00:22 (NCDB): WARN: MTLSE: fact: with the initialization of the initiator: mt
  Lint: 0x5d3a280 target bcmid:1 init bcmid: 3 rc 0, phba:0x5d40060
  15/01/14-09: 00:22 (NCDB): NOTE: target: irq_ptr:0x0xd77ec8, func:0 x 1, bcmId:0 x 1

  15/01/14-09: 00:22 (NCDB): NOTE: VendorID, DeviceId 0x19a2 0 x 210 bcmId 1 BDF 2.0
  .1
  15/01/14-09: 00:22 (NCDB): NOTE: target: VKI_INT_CONNECT success: status: 0x0
  15/01/14-09: 00:22 (NCDB): ERROR: target: SRI registered: irq_ptr:0xd77ec8, phba:0
  x38403b0, func:0 x 1
  15/01/14-09: 00:22 (NCDB): NOTE: BcmId [1] PCI [2.0.1]
  15/01/14-09: 00:22 (NCDB): NOTE: DFR 0 x 0210 VendId 0x19a2
  15/01/14-09: 00:22 (NCDB): NOTE: BAR0 e/s of basic size 0x00000000 0
  15/01/14-09: 00:22 (NCDB): NOTE: BAR1 MEM base 0xf0260000 size 1
  15/01/14-09: 00:22 (NCDB): NOTE: BAR2 MEM base 0xf0280000 size 1
  15/01/14-09: 00:22 (NCDB): NOTE: BAR4 MEM base 0xf02a0000 size 1
  15/01/14-09: 00:22 (NCDB): NOTE: MPU_EP_SEMAPHORE 0x0000c000
  Driver Build Date: Oct 25 2012, time: 15:03:42
  ServerEngines iSCSI Target driver loaded
  iSCSI Firmware Version: 2.901.319.0
  iSCSI Driver Version: 2.901.242.0
  Found BladeEngine2 in Gen2 x 8 PCIe slot
  15/01/14-09: 00:23 (NCDB): NOTE: region memory of Rwandan Patriotic Army: start 0x47492fe00 size 167
  77216 (ConIO-size 16777216) recorded for the pre-post on port 1 data buffers
  15/01/14-09: 00:23 (NCDB): WARN: MTLSE: default link on the interface-local address
  2 is fe80:0000:0000:0000:92 1 b: 1cff:fe37:7 b 42
  15/01/14-09: 00:23 (NCDB): WARN: MTLSE: default link on the interface-local address
  7 is fe80:0000:0000:0000:90 1:1 c 03 b: e837:7 b 42
  15/01/14-09: 00:23 (NCDB): WARN: MTLSE: default link on the interface-local address
  8 is fe80:0000:0000:0000:90 1:1 c 07 b: d037:7 b 42
  15/01/14-09: 00:23 (NCDB): WARN: MTLSE: fact: with the initialization of the target: 1 rc
  0
  15/01/14-09: 00:23 (NCDB): WARN: MTLSE: fact: lowLevelInit bcmId: 1 rc 0
  15/01/14-09: 00:23 (NCDB): WARN: MTLSE: start: lowLevelInit target bcmId: ins 2
  tId 2
  15/01/14-09: 00:23 (NCDB): NOTE: irq_ptr:0xd78480
  15/01/14-09: 00:23 (NCDB): NOTE: BcmId [2] PCI [2.0.6]
  15/01/14-09: 00:23 (NCDB): NOTE: DFR 0 x 0212 VendId 0x19a2
  15/01/14-09: 00:23 (NCDB): NOTE: IO BAR0 base 0xf0440000
  15/01/14-09: 00:23 (NCDB): NOTE: BAR1 MEM base 0xf0460000
  15/01/14-09: 00:23 (NCDB): NOTE: BAR2 MEM base 0xf0480000
  15/01/14-09: 00:24 (NCDB): WARN: MTLSE: fact: with the initialization of the initiator: mt
  Lint: 0x8d1bb00 target bcmid:2 init bcmid: 2 rc 0, phba:0x8d1e060
  15/01/14-09: 00:24 (NCDB): NOTE: target: irq_ptr:0x0xd77ce0, func:0 x 2, bcmId:0 x 2

  15/01/14-09: 00:24 (NCDB): NOTE: VendorID, DeviceId 0x19a2 210 bcmId 0 x 2 BDF 2.0
  .2
  15/01/14-09: 00:24 (NCDB): NOTE: target: VKI_INT_CONNECT success: status: 0x0
  15/01/14-09: 00:24 (NCDB): ERROR: target: SRI registered: irq_ptr:0xd77ce0, phba:0
  x3840ac0, func:0 x 2
  15/01/14-09: 00:24 (NCDB): NOTE: BcmId [2] PCI [2.0.2]
  15/01/14-09: 00:24 (NCDB): NOTE: DFR 0 x 0210 VendId 0x19a2
  15/01/14-09: 00:24 (NCDB): NOTE: BAR0 e/s of basic size 0x00000000 0
  15/01/14-09: 00:24 (NCDB): NOTE: BAR1 MEM base 0xf02c0000 size 1
  15/01/14-09: 00:24 (NCDB): NOTE: BAR2 MEM base 0xf02e0000 size 1
  15/01/14-09: 00:24 (NCDB): NOTE: BAR4 MEM base 0xf0300000 size 1
  15/01/14-09: 00:24 (NCDB): NOTE: MPU_EP_SEMAPHORE 0x0000c000
  Driver Build Date: Oct 25 2012, time: 15:03:42
  ServerEngines iSCSI Target driver loaded
  iSCSI Firmware Version: 2.901.319.0
  iSCSI Driver Version: 2.901.242.0
  Found BladeEngine2 in Gen2 x 8 PCIe slot
  15/01/14-09: 00:25 (NCDB): NOTE: region memory of Rwandan Patriotic Army: start 0x47592fe00 size 167
  77216 (ConIO-size 16777216) registered for the data pre-post on port 2 buffers
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: default link on the interface-local address
  3 is fe80:0000:0000:0000:92 1 b: 1cff:fe37:7 b 43
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: default link on the interface-local address
  9 is fe80:0000:0000:0000:90 1:1 c 03 b: e837:7 b 43
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: default link on the interface-local address
  10 is fe80:0000:0000:0000:90 1:1 c 07 b: d037:7 b 43
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: fact: with the initialization of the target: 2 rc
  0
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: fact: lowLevelInit bcmId: 2 rc 0
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: start: lowLevelInit target bcmId: ins 3
  tId 3
  15/01/14-09: 00:25 (NCDB): NOTE: irq_ptr:0xd78298
  15/01/14-09: 00:25 (NCDB): NOTE: BcmId [1] PCI [2.0.7]
  15/01/14-09: 00:25 (NCDB): NOTE: DFR 0 x 0212 VendId 0x19a2
  15/01/14-09: 00:25 (NCDB): NOTE: IO BAR0 base 0xf04a0000
  15/01/14-09: 00:25 (NCDB): NOTE: BAR1 MEM base 0xf04c0000
  15/01/14-09: 00:25 (NCDB): NOTE: BAR2 MEM base 0xf04e0000
  15/01/14-09: 00:25 (NCDB): WARN: MTLSE: fact: with the initialization of the initiator: mt
  Lint: 0x8e829a0 target bcmid:3 init bcmid: 1 rc 0, phba:0x8e86060
  15/01/14-09: 00:25 (NCDB): NOTE: target: irq_ptr:0x0xd77af8, func:0 x 3 bcmId:0 x 3

  15/01/14-09: 00:25 (NCDB): NOTE: VendorID, DeviceId 0x19a2 0 x 210 bcmId 3 BDF 2.0
  .3
  15/01/14-09: 00:25 (NCDB): NOTE: target: VKI_INT_CONNECT success: status: 0x0
  15/01/14-09: 00:25 (NCDB): ERROR: target: SRI registered: irq_ptr:0xd77af8, phba:0
  x38411d0, func:0 x 3
  15/01/14-09: 00:25 (NCDB): NOTE: BcmId [3] PCI [2.0.3]
  15/01/14-09: 00:25 (NCDB): NOTE: DFR 0 x 0210 VendId 0x19a2
  15/01/14-09: 00:25 (NCDB): NOTE: BAR0 e/s of basic size 0x00000000 0
  15/01/14-09: 00:25 (NCDB): NOTE: BAR1 MEM base 0xf0320000 size 1
  15/01/14-09: 00:25 (NCDB): NOTE: BAR2 MEM base 0xf0340000 size 1
  15/01/14-09: 00:25 (NCDB): NOTE: BAR4 MEM base 0xf0360000 size 1
  15/01/14-09: 00:25 (NCDB): NOTE: MPU_EP_SEMAPHORE 0x0000c000
  Driver Build Date: Oct 25 2012, time: 15:03:42
  ServerEngines iSCSI Target driver loaded
  iSCSI Firmware Version: 2.901.319.0
  iSCSI Driver Version: 2.901.242.0
  Found BladeEngine2 in Gen2 x 8 PCIe slot
  15/01/14-09: 00:26 (NCDB): NOTE: region memory of Rwandan Patriotic Army: start 0x47692fe00 size 167
  77216 (ConIO-size 16777216) registered for the data pre-post on port 3 buffers
  15/01/14-09: 00:26 (NCDB): WARN: MTLSE: default link on the interface-local address
  4 is fe80:0000:0000:0000:92 1 b: 1cff:fe37:7 b 44
  15/01/14-09: 00:27 (NCDB): WARN: MTLSE: default link on the interface-local address
  11 is fe80:0000:0000:0000:90 1:1 c 03 b: e837:7 b 44
  15/01/14-09: 00:27 (NCDB): WARN: MTLSE: default link on the interface-local address
  12 is fe80:0000:0000:0000:90 1:1 c 07 b: d037:7 b 44
  15/01/14-09: 00:27 (NCDB): WARN: MTLSE: fact: with the initialization of the target: 3 rc
  0
  15/01/14-09: 00:27 (NCDB): WARN: MTLSE: fact: lowLevelInit bcmId: 3 rc 0
  15/01/14-09: 00:27 (NCDB): SOD: pre to complete initialization Phase
  15/01/14-09: 00:39 (NCDB): WARN: CmgrLockdownException: OF CORRUPTION of the DBM DATABASE
  COPYRIGHTS - LOCKDOWN Type = 6
  15/01/14-09: 00:39 (NCDB): NOTE: ACS: necessary Acs on Alt: no, StateCode: 6, Reas
  onCode = 12
  15/01/14-09: 00:39 (NCDB): NOTE: ACS: icon alternate ping failed:-2, RESP.:
  0
  AcsCommunicator::getInstance() indeterminate Mode, using DOMI
  15/01/14-09: 00:39 (NCDB): WARN: ACS: altValidateStagedFirmware(): Domi outstanding
  taken on: IconSendInfeasibleException error
  15/01/14-09: 00:40 (NCDB): SOD: initialization of synchronization of the Code Phase complete
  you
  15/01/14-09: 00:39 (NCDB): WARN: case - CORRUPTED DB Lockdown. VPN did not update
  of Sstor.
  15/01/14-09: 00:40 (NCDB): SOD: initialization Phase complete
  ==============================================
  Title: Disk Array Controller
  Copyright 2008 - 2012 NetApp, Inc.. All rights reserved.

  Name: RC
  Version: 07.84.44.60
  Date: 25/10/2012
  Time: 14:41:57 CDT
  Models: 2660
  Manager: devmgr.v1084api04.Manager
  ==============================================

  15/01/14-09: 00:39 (NCDB): NOTE: available symbol
  15/01/14-09: 00:39 (NCDB): WARN: *.
  ***********
  15/01/14-09: 00:39 (NCDB): WARN: *.
  ***********
  15/01/14-09: 00:39 (NCDB): WARN: *.
  **
  15/01/14-09: 00:39 (NCDB): WARN: * WARNING!
  **
  15/01/14-09: 00:39 (NCDB): WARN: *.
  **
  15/01/14-09: 00:39 (NCDB): WARN: * this controller is locked because of the detec
  Ted *.
  15/01/14-09: 00:39 (NCDB): WARN: * bribery in the primary database.
  **
  15/01/14-09: 00:39 (NCDB): WARN: * in order to avoid any loss of configuration.
  the *.
  15/01/14-09: 00:39 (NCDB): WARN: * backup database must be restored.
  **
  15/01/14-09: 00:39 (NCDB): WARN: *.
  **
  15/01/14-09: 00:39 (NCDB): WARN: *.
  **
  15/01/14-09: 00:39 (NCDB): WARN: *.
  ***********
  15/01/14-09: 00:39 (NCDB): WARN: *.
  ***********
  15/01/14-09: 00:40 (NCDB): SOD: sodComplete complete Notification
  15/01/14-09: 00:40 (NCDB): sodMain CtlrLockdown sequence complete, elapsed time
  = 35 seconds
  15/01/14-09: 00:40 (NCDB): full sodMain
  15/01/14-09: 00:39 (NCDB): WARN: sequence of lockdown SOD full - suspension...

  If you have the serial cable or reset password cable as the manuals refer to it, you can remove the lock status. I know that this command works, but only if you are able to enter commands in the CLI by the serial port. If she will accept the orders, you will see a-> when you press on enter. The clear locking control is lemClearLockdown I believe. It can be so lemClearlockdown.

  These controllers go in many States of lockdown too easy if you ask me... I fight 10 + MD32XX units right now. Although I can't enter commands in the CLI, it enters just text and does not recognize it as any kind of order. I hope that you are not as lost as mine, I've got one under warranty, so I'm about to call Dell technical support. I'll post an update when I'm done crying.

  Good luck

• Error Protocol in the package received from the initiator

  I have a Windows 2008 R2 virtual machine connected to a PS of the Group (6210xs and 6000). I have 4 volumes iscsi LUNS for Windows data, two on the 6210 and two on the 6000. The vm is on the 6210. We have implemented the 6210 back towards the beginning of the year, and all volumes of data have been implemented with MPIO 5 or 6 months ago.

  This morning, one of the 2 data on the 6210 disappeared. Windows Disk Mgmt did not show it online or offline, but the windows iscsi initiator showed as connected LUNs. I disconnected the lun and reconnected and immediately handed volume online and has been fully accessible. The monitor EQ had a message to info about the disconnect with "error Protocol in the package received from the initiator" at the end of the message. 2 seconds later, the logical unit number reconnected.

  It sounds like a problem with the initiator of windows rather than a problem of EQ, but I thought I'd check here in any case. It is interesting that it happened only to 1 volume of 4. This volume has been connected since May with no problems until today, and I do not have no changes to configuration since May. Are both the vNIC multichannel vmxnet3 with all the same settings (jumbo frames enabled, unloading of the disabled, numbers for Rx rings, etc.)

  Any ideas on all the settings should I check or change, especially with the network cards for?  I'll probably post this on technet, too.

  Thank you.

  Tim

  Hello

  The problem with iSCSI optimization is that it keeps track of connections.  However, the table moves periodically as you have noticed, the connections.  The switch fw does not understand that.  With each stroke he follows the new session and retains the old.   The buffer allocated for it is rather low.  According to FW versions on the switches, this could be as little as 256 connections.  Over time, this buffer is overrun.  The older of the switch that made to block any new connection iSCSI on port 3260.   So turn it off is the best option.

  Re: trunk. In general the ISCSI traffic is burst, so when you look at the history of the traffic it appears wrong, because he gets on average over time.  So, I would add at least two additional ports to be sure.

  Kind regards

  Don

• MD3220i - firmware update fallito knew a controller

  Ho made upgrade firmware di di a MD3220i alla versione 08.20.16.60.

  E' tutto ok sul primo fits controller, mentre he secondo e fits in error.

  Ho gia SC lo storage e con tried MDSM (version 11.20), one my upgrede del firmware rieffettuare ho UN error recovery guru che indica che nella it module in slot 1 e raid controller in stato "Removed".

  In effetti nel dell ' hardware' TAB ' MDSM nella sezione of pregnant (back) e: empty RAID controller module connector.

  In both realta sono e any modules I riesco dello di pingare 2 place management storage interfaces.

  Buongionro, ha per caso, tried one invertire I controllers?

  Questo comporta he fermo Attività.

  Francesco

• Error of VSS volume controls with SUCCESS / ME

  I finally had time to MPIO configuration for data NTFS on a Windows 2008 R2 vm to my EQ group, but I get an error 'VSS volume control is not accessible from this host'. I have the EQ, access policy VSS to IP to accept the whole subnet.  Notifications of EQUALIZER error includes "CHAP grpadmin authentication failed", but I'm only using the IP access, chapter not CHAP is optional, no? This is a subnet on the internal switches.  In addition, access to the Group PS, "Use Chap credentials for iscsi discovery" don't are not ticked.

  In the view of host MPIO, connections iscsi displays "2 ok, 2 bad." I only have 2 network cards on this virtual machine.

  Edit: Also, in the Group Access window, access to VDS/MVS has a green check mark.

  Hello

  Probably that's because there's a CHAP ACL on the vss-control volume.  When the remote installation wizard to configure the table he asks you to create a name of user and password c.  He uses the ACL on the default vss control volume.

  If you delete this ACL CHAP error will probably disappear.

  Kind regards

• ESXi MPIO FC connection to storage

  Hi guys,.

  How does Esxi meter MPIO for FC connection to the storage? If I have 2 HBA Esxi uses as well for balancing the connection to the storage or using only 1 hba as active and other as before to handle an error?

  Thanks in advance.

  Use only 1 connection at a time (but it can, depending on the storage, switch between them).

• MD3220i - install the drivers 'to host' on ESXi hosts

  We bought a MD3220i to use as shared to our vmware datacenter storage.

  I'm a little confused by the documentation...

  She says that she needs to host software installed on each host that connects to the MD3220i and the software grouped: the driver agent and multiple paths to storage. And that any host servers that connect to the storage array need.

  Without doubt, this also includes ESXi hosts?  If so - how do install on ESXi hosts?

  Or I completely understood you something here...

  Advice would be appreciated,

  S.

  You have no software special 'host' because all the parts needed is already bundled with vsphere ESX (i). The essential parts are to check if the right HOME is used and that configure you the initiator of swiscsi in the right way. In terms of vsphere4 you need some Voodoo (remote control) command line to use esxcli to bind the VMKs created together.

  Reference Dell have a best practice on how to connect the md32x0i to vsphere which has been found at the momemt. The guide shows the ip network configuration and all the necessary parts in vsphere. Dell uses a subnet of grand for all ports of 2 controllers. If you are looking for in this forum you will also find configurations where a single subnets are used to place a port for each controller. The two works configuration but I do face "LUN is not on preferred path" errors from time to time during the use of the first installation.

  If you call technical support Dell will send you the necessary guide but I do not know google can help as well. Its like for many other iscsi bays and rules applied (several VMKs, binding, etc.). If you can't find something I can dig in my Inbox if necessary.

  Edit:

  OK... after a google search hard that I found the former guide who use a single subnet, but the guide describes the installation with different subnets. Then you should follow this path. Take a look at http://www.dell.com/downloads/global/products/pvaul/en/md-family-deployment-guide.pdf

  Concerning

  Joerg

  Added the latest Dell best practices guide

• Uninstall software update Apple says error in seller contact package package unstaller

  Try to get itunes working to make a backup of my faulty iphone before repair.

  First-itunes does not start says error. I'm trying to fix it, who said success but same error when you try to start it.

  Then uninstall completely worked. Then reinstall that seemed to be over except for a message "an older version of Apple software update already exists" then he went down and install itunes apparently had not been completed.

  Then I try to remove the update from the apple software and executed by an error in the installation program - it says there is an error in the installation and contact the supplier of the installation package. Same error if I run the uninstall command line program.

  Try to repair the Apple Software Update of programs & features Control Panel and then try to update iTunes again.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  The more information box has direct links with the current and recent if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit - for older video cards) as a workaround for problems with installation or operation, or compatibility with third-party software.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• SUMIF error

  I'm new to apple and get a syntax error when you use SUMIF.  In my table, I just need column F to test the value of column E.  If it is greater than 0, then divide by 20.  Thank you!

  In cell F1

  = E1/if(E1>0, 20, 1)

  fill down as needed

• An error in this Applescript that I can't understand

  Hi, I searched some forums and found this script below which I modified. It works great except for a single statement:

  runScript If = 1 then number error -128 I want the script to do is, when a USB drive is mounted and is in the ignoredVolumes as "USB Untitled" I want the script to stop. What I can't understand is, runScript is set to 1, "Untitled USB" Monte, runScript is not changed, why don't the script stops with an error "user cancelled"? On the other hand, if a key USB Monte is not in the ignoredVolumes, runScript is set to 2 and copy the file I want it. What hurts? It's probably something that will be very obvious when I see the answer.

  Thanks for any help with this problem,

  Mike.

  
  

  
  

  property ignoredVolumes: {'10,10 30 1. 5 't', 'files 1. 5 't', "Untitled USB"} - add if necessary

  property videoExtensions: {"avi", "mov", "mpg", "wmv", "mp4" and "mkv"}

  the value newVolume to the alias (POSIX file "/ Volumes/files 1.") ("5T / new")

  the value oldVolume to the alias (POSIX file "/ Volumes/files 1.") ("5T / old")

  game runScript to 1

                 tell application "System events".

  the value rootVolumes to disk (POSIX file ' / Volumes ' in the text)

  the value allVolumes to name of every element of disc of rootVolumes

  the value numofallVolumes to the County of allVolumes

  Repeat with the present book in allVolumes

  say application 'Finder '.

  if (the present book is not in ignoredVolumes and (this book as text) is not '. ') DS_Store') then

  if there are alias (POSIX (' / Volumes / "& the present book) as text file ) then game runScript to 2

  runScript If = 1 then number error -128 - it does not give a 'User cancelled' error when "Untitled USB" is mounted

  runScript If = 2 then

                                                                          try

  duplicate (elements whose name is in the videoExtensions extension) in alias (POSIX file (' / Volumes / "& the present book &" / new ") as text) to newVolume

  on error number errorNumber errorMessage

  _error value of errorMessage

  _errorNum the value to errorNumber

  If errorNumber is -15267 then

  display the dialog box "This file already exists in folder a." buttons {"OK", "No"} default button 1 with the title "Film copy error?" giving upwards after 10

  If the returned button of result is 'No' then

  Error number-128

  on the other

  If the result is 'OK' or back button gave up lead and then of

  eject the present book

  display the dialog box "U S B D r i v e E j e c t e d - K O t o R e m o v e" {"no need to click on this button"} default button 1 button give up after 5

  return

  end if

  end if

  end if

  end try

  Try

  duplicate (elements whose name is in the videoExtensions extension) in alias (POSIX file (' / Volumes / "& the present book &" / old ") as text) to oldVolume

  on error number errorNumber errorMessage

  _error value of errorMessage

  _errorNum the value to errorNumber

  If errorNumber is -15267 then

  display the dialog box "This file already exists in the folder B" buttons {"OK", "No"} default button 1 with the title "Film copy error?" giving upwards after 10

  If the returned button of result is 'No' then

  Error number-128

  on the other

  If the result is 'OK' or back button gave up lead and then of

  eject the present book

  display the dialog box "U S B D r i v e E j e c t e d - K O t o R e m o v e" {"no need to click on this button"} default button 1 button give up after 5

  return

  end if

  end if

  end if

  end try

  display the dialog box "USB key will Auto Eject in 10 seconds or click OK... "buttons button 1 with the title"copy Complete - Eject? "default {'OK', 'No'} which gives after 10

  If the returned button of result is 'No' then

  Error number-128

  on the other

  If the button returned of result is "OK" or gave up a result then ejection of the this book

  display the dialog box "U S B D r i v e E j e c t e d - K O t o R e m o v e" {"no need to click on this button"} default button 1 button give up after 5

  end if

  end if

  end if

  end say

  end Repeat

            end say

  The way in which your external block If is currently based, the script can't do anything when this book is in the ignoredVolumes, it can not yet test the runScript value. Try something like this:

  If the present book is in the ignoredVolumes then

  game runScript to 1

  on the other

  if (the present book as text is not '. ') DS_Store') then

  if there are alias (POSIX (' / Volumes / "& the present book) as text file ) then game runScript to 2

  end if

  end if

  
  

  Of course, you need to remove a "end if' the end of the script.