Favorites lost - cannot create others. Vista/IE7.

Similar Questions

• Satellite L - cannot create the Vista recovery disc

  Hello. I am trying to create the recovery disk. Takes 2 DVD, no problem with the 2, but when I am burning nr.1 and is about to finish showing me the error message:

  The following question has occurred during the recording of the data on the disk.
  The current process will be stopped.
  A power calibration area error.
  Please check if the disc is scratched dirty.
  If so, please try again with a new disc.
  (error code: 0E01B5-26-00037304)

  I tried 3 or 4 times, brand new DVD each time. Any ideas?

  Hi zombi71,

  What brand of DVD that you've already used? These burning questions can be linked to the mediums of poor quality so it s recommended using mediums high quality only. I have pretty good experience with Verbatim and TDK discs and especially with the DVD-R DVD + R. So I would recommend Verbatim DVD-R. With this brand, it was possible to create the mediums of recovery on my laptop. :)

  Check this box!

• Vista cannot create a network map

  the two 2 computers running Windows Vista Edition Home Premium.  Network and sharing screens put in place identical.  On my computer (from the network and sharing Center), I can click on view full map and it shows my network card.  On the computer of my wife (of the network and sharing Center) she can click on view full map and it rises "Windows cannot create a network adapter for the selected type of connection networl.  I might add that both computers are 'wired' internet/router.

  Any help?

  Hi Duane_TN,

  Are your computer and your computer wife have chipset or card network NVIDIA perchance? or a Linksys router by chance?  This is a post in the forum of Linksys, you might want to check in to see if it applies to your computers:

  Symptom: Windows Vista computers are not put on the Vista network map. Or well, you get the following message when you try to view the full network map: "Windows cannot create a network adapter for the type of connection chosen network." To check go to: PANEL-> CENTER NETWORK AND SHARING. SEE the FULL map (top-right) and find either: A Windows Vista-based computer is listed down under: "the following peripheral discovered may not be placed in the plan. or You get the message, "Windows cannot create a network adapter for the type of network connection. Possible cause: The offending computer has an NVIDIA nForce Networking Controller whose property "priority and VLAN" to "priority"active & VLAN. Solution: Set the property 'priority & VLAN"to"Priority and VLAN Disabled"as follows: Reach: START-> CONTROL PANEL-> ADMINISTRATION-> COMPUTER MANAGEMENT TOOLS In the resultant "computer management" window select: DEVICE MANAGER (left side). "NICs" (right). Expand "Network adapters" and see if it lists a NVIDIA nForce Networking Controller. Right click on 'NVIDIA nForce Networking Controller' and select 'properties '. In the resultant 'NVIDIA nForce Networking Controller Properties' window, select: "Advanced"(tab) ". Under the list of the 'properties', select 'priority & VLAN. for 'Value' assign ' priority and VLAN disabled. References: ---------- How to get the Vista network map works on nVidia MB http://www.TechIMO.com/Forum/networking-Internet/197756-how-get-Vista-network-map-working-NVIDIA-MB.html Other things to check: Update to the latest version of the driver (65.7.4.0 works for me). Article referenced above indicates a previous driver may be bad.

  Hope this helps, Kevin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot create folders or other elements in the same drop-down menu in "organize bookmarks".

  Cannot create new bookmark files. 'Create a new folder' and all the other relevant elements that scrolls to organize the bookmarks are grayed out.

  I have exactly the same problem. Have not found the solution.
  21/07/10

• Cannot create an ad hoc network on Windows Vista

  Hi all

  I tried to create an ad hoc network on my PC but as soon as I get a name and a password, Windows returns the message "Windows cannot create the network"XXXX" I've not really changed anything since yesterday when I was able to create another network without problem, except a failed restart (to manually turn off my PC because restart took too long).

  I tried to change the Autoconfiguration WLAN service (as had been suggested at: http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/cant-create-an-ad-hoc-network/94028a00-54ec-4cd1-81a0-ab35718d62e5) but it is already configured in automatic mode, and it did not work.

  Any help would be greatly appreciated I need emergency back network!

  This info should help:

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-computer-to-computer-ad-hoc-network

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-computer-to-computer-ad-hoc-network

• Cannot create a system under Vista Home Premium SP1 Restore Point

  If I try to create a system restore point manually, I get the following error:

  The shadow copy provider had an unexpected error while trying to process the specified operation (0x8004230F)

  I rebooted, restarted the VSS service, but still no luck. Someone at - he found a solution to this short error reinstall Vista?

  Hello

  Check the fix here as it is similar:

  Difficulty 0 × 8004230 C error in Windows
  http://www.mydigitallife.info/2008/06/27/fix-0x8004230C-error-in-Windows/

  -----------------------------

  Also that to help clear corruption and repair/replace damaged/missing system files:

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------

  You could try to remove and rebuild your region ShadowCopy.

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  How to turn System Restore on or off in Vista
  http://www.Vistax64.com/tutorials/66971-system-restore.html

  Adjustment of the amount of disk space, System Restore uses for restore points
  http://bertk.MVPs.org/html/diskspacev.html
  How to change how much Space System Restore can use
  http://www.Vistax64.com/tutorials/76227-system-restore-disk-space.html
  http://www.Petri.co.il/change_amount_of_disk_space_used_by_system_restore_in_vista.htm

  ShadowStorage vssadmin commands
  http://TechNet.Microsoft.com/en-us/library/cc755866 (WS.10) .aspx
  http://technet2.Microsoft.com/WindowsServer/en/library/89d2e411-6977-4808-9AD5-476c9eaecaa51033.mspx?mfr=true

  Guide to Windows Vista system restore
  http://www.bleepingcomputer.com/tutorials/tutorial143.html

  Expiration errors occur in Volume Shadow Copy service writers, and shadow copies are lost during
  backup and at the time when there are high levels of input/output
  http://support.Microsoft.com/?ID=826936

  A good utility:

  Explorer of the shadow - free
  http://www.ShadowExplorer.com/

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Word documents: Is there some Word Documents created in Vista which cannot be open in XP?

  Is there some Word Documents created in Vista which cannot be open in XP?

  Following the correct advice of Ken Blake MVP, here is the link for the Office Compatibility Pack Ken Blake MVP mentioned:

  http://www.Microsoft.com/downloads/details.aspx?FamilyID=941b3470-3ae9-4aee-8f43-c6bb74cd1466&DisplayLang=en

  "Open, edit and save documents, workbooks, and presentations in the file formats Open XML, which were introduced in Microsoft Office Word, Excel, and PowerPoint beginning with Office 2007."

  See you soon.

  Mick Murphy - Microsoft partner

• Windows cannot create the network map. Responses of the other devices on the network are delayed or on the network, there is a router incapatible

  Original title: no network card
  I installed a NETGEAR N300 Wireless USB Adapter on my computer which is a desk top Dell 64-bit running Windows 7 Edition Home Premium. There are five computers on my network. Two of the others use the same model of NETGEAR wireless USB adapt. I removed the Ethernet cable after the installation of the wireless adapter. I can say that the new wireless adapter works fine. When I tried to map the network I got the same message that appears in some of these problems: "Windows cannot create the network map. Responses of the other devices on the network are delayed or there is a router on the network incapatible". I have restarted this computer in SafeMode as suggested in the above problems. I tried other things like disabling the wired connection has always existed for the cable. No effect. Then I tried mapping the network on the other computers. All failed with the same message. All the other four computers are 32-bit. Three of these computers are also running Windows 7 Home Premium. They are the best desktop computers. The other computer is a Windows 7 Starter netbook running. It is the 32-bit computer, always using a cable. That will be replaced with the same wireless adapter model NETGEAR. Anyone know how to fix this or is this a bug? It would be nice of the network software of Windows 7 has worked as it is supposed to. TO.

  I went the last wired wireless computer and the problem disappeared. The five computers can view the map now without any problems.

• Tecra A10 - lost HDD Recovery for Vista

  Hello Toshiba,

  I bought a Tecra a month ago. Here are the details:
  Device name: Tecra A10 - 11L
  Unit number: PTSB0E-00C006AR

  For some reason I have to downgrade the machine in Windowx XP (using the CD-ROM supplied in the packaging recovery). I do not use Vista.
  Now I need to go back to the factory installed Vista Business.
  I didn't create a Vista recovery CD before downgrading to XP.

  I think I lost recovery disk for Vista.

  Then I found the site to order: https://backupmedia.toshiba.eu/serial.aspx

  1. I'm not sure I'll order the recovery Vista or XP Media?, it shows (price (including VAT): EUR 29.33)
  What recovery media that I will get?
  a. VISTA Business recovery
  b. recovery XP Media? (that I have)

  2 is there a hidden partition that I can use it to retrieve the vista?

  Can someone help/guide me?

  Sincerely,

  Andrew

  You are right. After installing Windows XP edition family the HDD recovery went and it cannot be used to install more factory settings. There is no hidden partition and you can't do anything.
  I really don't understand why you ignored Toshiba reminder on creating recovery DVDs.

  In any case, I think that you will get Vista 32 Bit SP1 Business (EN) because with this OS is delivered and preinstalled Tecra.

• I tried to look at my device manager and go this message MMC cannot create a snap

  I wasn't at the root droid to my husband, to see if the installation of the driver, have been, to my horror, saw NO Device Manager, just MMC cannot create a snap.

  I think I'll probably have to do a clean re install to get this and a few other problems I've seen lately. Any suggestions?

  Hi beckyandac

   

  1. what other issues do face you?
  2. for how long have you been faced with this problem?
  3. did you of recent changes on the computer?
  4. do you get error messages when you try to open Device Manager?

   

  Method 1:

  Try opening the Device Manager by following the steps mentioned.
  Click the Start button, then click on control panel - system and Maintenance, then select Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  Method 2:
  You can perform a scan of the SFC (System File Checker). It lists all the issues and will also retrieve all files if necessary. Follow the steps below to perform a Scan SFC -

  a. click Start, click programs, on Accessoriesprincipally made, right click guestand then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click Allow
  b. type the following command and press ENTER:
  sfc/scannow
  A message appears indicating that "the system scan will start. Be patient because the scan can take some time.
  c. If all files require a SFC replace will replace them. You may be asked to insert your Win7 DVD for this process to continue.
  d. If everything is correct you should, after the scan, see the following message "resource protection Windows not found any breach of integrity".
  e. once the scan is finished, close the command prompt window, restart the computer and check.

  See the link for further directions on scan SFC - below
  http://support.Microsoft.com/kb/929833

   

  Method 3:
  If the problem persists, you can check if you are facing the same question in the user account new or different administrator account.  You can create a new user account on your computer, and then check.

  Create a new user account-
  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  If you are not faced with the same question in a new user account, you can view the link below and use the steps provided to fix a corrupted - user profile
  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

   

  I hope this helps.

• In creation of Windows 7 DVD, download "unspecified error cannot create DVD.

  in creation of w7 dvd, I get after 0.8% "unspecified error cannot create dvd" How can I find this kind of error is, so I can fix it, because on this forum, there is no real answer to this problem. I have a new 64 bit w7 pro, no other software installed computer and works fine engraving only dvd burner the files.

  Hi alexveres,

  1. what type of file you want to burn?

  2. is it works much earlier? If so, then remember to make changes to the computer?

  Take a look at the following links for possible solutions and check if that helps:

  Error message when you try to publish a movie to a DVD using Windows DVD creation in Windows Vista: "unspecified error".

  Problem with "unknown error" when burning DVD

  I hope this helps.

• Cannot create a new folder name

  Cannot create a new folder and name it.  The name I give always comes back again record when I hit enter.

  I'm assuming that happens with all new folders in the special folder that you use and that you use a "legal" name for the folder - but that is determined when you answer questions of Malke.

  It's maybe a permissions issue.  You will have to perhaps take full rights on the folder or even take in charge of the case.

  To view your permissions, right-click on the file/folder, click Properties, and check the Security tab.  Check the permissions you have by clicking on your user name (or group of users).  Here are the types of permissions, you may have: http://windows.microsoft.com/en-US/windows-vista/What-are-permissions.  You must be an administrator or owner to change the permissions (and sometimes, being an administrator or even an owner is not sufficient - there are ways to block access (even if a smart administrator knows these ways and can move them - but usually should not because they did not have access, usually for a very good reason).)  Here's how to change the permissions of folder under Vista: http://www.online-tech-tips.com/windows-vista/set-file-folder-permissions-vista/.  To add take and the issuance of right of permissions and ownership in the right click menu (which will make it faster to get once it is configured), see the following article: http://www.mydigitallife.info/2009/05/21/take-and-grant-full-control-permissions-and-ownership-in-windows-7-or-vista-right-click-menu/.

  To resolve this problem with folders, appropriating the files or the drive (as an administrator) and give you all the rights.  Right-click on the folder/drive, click Properties, click the Security tab and click on advanced and then click the owner tab.  Click on edit, and then click the name of the person you want to give to the property (you may need to add if it is not there--or maybe yourself). If you want that it applies to subfolders and files in this folder/drive, then check the box to replace the owner of subcontainers and objects, and click OK.  Back and now there is a new owner for files and folders/player who can change the required permissions.  You can change now switched to read-only (even if the main folder indicates that they are always read-only - you can access yourself as the owner).  You can keep them in read-only to other users, customers and administrators even (although they can support themselves and access, if they wish, and it is really not that you can do to stop it except protect the file with a password by using a 3rd party product.)  Here is more information on the ownership of a file or a folder: http://www.vistax64.com/tutorials/67717-take-ownership-file.html.  To add take ownership in the menu of the right click (which will make it faster to get once it is configured), see the following article: http://www.howtogeek.com/howto/windows-vista/add-take-ownership-to-explorer-right-click-menu-in-vista/.

  Good luck and I hope this helps!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot see other computers on my workgroup

  I wiped my computer "arizonahp" and did a fresh install of Windows 7 Ultimate 64 bit.  Everything works fine except that it cannot see other computers on my working group (all current running xp) and they know more see 'arizonahp '.  I clear my name of working group "yorklan" in my computer.  Previously, arizonahp was a vista machine and he could see and be seen.

  What could be the problem?
  Thank you
  Gary .net developer

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  In Windows 7, go to control panel > everything in Control Panel > network and sharing Center. Click on "change the advanced sharing settings. You don't want to use the residential group unless you have all Windows 7 machines. If you do and you want to use the homegroup, see Windows 7 Help & Support. Otherwise, in sharing advanced:

  Discovery of plug in the network
  Open the files and printers sharing
  Turn on the sharing section Public folder sharing
  Plug the password protected sharing

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, running on Windows 7 sharing files and printer as above will take care of this for you. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  Start > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers on your network are XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. In Windows 7 I usually share the Desktop of the user and the Public directory. MS - MVP - Elephant Boy computers - don't panic!

• Cannot create the Image of the system or system, unknown error repair disc: 0x80004005.

  Original title: cannot create the Image of the system or system repair disc

  I just bought a new Windows 7 computer. I tried to create a system repair disc, but still receive the error msg - error (0x80004005) unspecified. I tried - and lost - several DVDs in the process. Also, not able to create a System Image disc. The computer says that I have to format the drive and when I click OK, it goes through the movement, then gives me an error msg that the Format has failed. (In addition, it does me not the possibility not to format the drive.)  Very frustrating...

  Hi iamkira,

  This problem can be caused by a conflict with other programs installed on your computer, usually antivirus software. Follow the steps described in this document to create the drive in a clean boot state.

  Let us know if that helps.

• Another: failed: cannot create a snapshot VSS of the source volumes. Error 2147549183 but on XP Pro

  I am changing a laptop Windows XP Pro using the converter software 4.0.1.

  He will start the conversion process, but after 10 seconds or so, I get the error: failed: cannot create a snapshot VSS of the source volumes. Error 2147549183

  The strange thing is my images of box Vista successfully without problem.

  I'm in a corporate environment. I moved the laptop test I try the image of an OU restrictive and placed in a non-restrictive ORGANIZATIONAL unit (without firewalls and others). I always have the same question.

  I made sure all the VSS services and these are running and active. I even tried MS KB Article 941956 comes to do even if it said it was only for Server 2003.

  Any other pointers on this? It seems that a lot of people get this error, but the only ones I can find are for server operating systems... not XP.

  In the event under application Viewer I have errors of:

  Type: error

  Event ID: 12292

  The volume shadow copy Service error. Error creating the Shadow Copy Provider COM with CLSID {65ee1dba-8ffa-4a58-ac1c-3470ee2f376a} class

  Type: WARNING

  Event ID: 4356

  {The COM system + impossible to create an instance of the Subscriber partition:{41e90f3e-56c1-4633-81c3-6e8bac8bdd70}!new:{d3938ab0-5b9d-11d1-8dd2-00aa004abd5e}. CoGetObject returned HRESULT 80070005

  Type: WARNING

  Event ID: 4353

  The event of COM + a system attempted to raise the EventObjectChange::ChangedSubscription event but received a bad return code. HRESULT was80040201

  Type: error

  Event ID: 8193

  Volume Shadow Copy Service Error: Unexpected error calling routine CoCreateInstance. HR = 0 x 80004002

  You are able to start these three services; EventSystem, swprv, vss?

  What is this command returns; "vssadmin list writers"?

  Joakim