Financial reports - 11.1.2.1 client - connects via VPN only?
HelloWhen I'm directly connected to the network or connected via their intranet wireless, I can connect to fin reports customer of Studio. However, if I train via VPN (Juniper), he returns with a message: you are not authorized to access. Please contact your system administrator. It is a mistake to end too many reports? Any ideas why/how this could happen?
It is possible that your VPN is not open ports that you can use EN Studio.
See you soon
John
http://John-Goodwin.blogspot.com/
Tags: Business Intelligence
Similar Questions
-
Situation: we have a few portable computers test Ubuntu running DHCP servers. We need get the updates and other changes in corporate network sometimes. Today, we turn off the DHCP server, set up to get an IP via DHCP (besides) and make our updates.
Problem: we do not want someone accidentally connect the laptop to the corporate network, while its DHCP server is running.
Question: so, if we go via wifi using a Cisco VPN client, the DHCP server IP addresses above the tunnel?
Thanks for reading.
N ° DHCP uses layer 2 broadcasts to disseminate IP addresses. Because your clients are connected via VPN, there is no contiguity of layer 2. The only way he would accidentally do it is if you have configured an address to support IP dhcp as one of your VPN clients on the network, which I imagine you wouldn't.
-
Have an ASA5505. Here is the error message that gives the Client VPN log trying to connect.
Here is your posted initial configuration changes. This will allow you to hit all your existing ports to 192.168.1.50 and 1.30. It will also keep your clear external interface for the vpn.
not static (inside, outside) interface 192.168.1.50 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 192.168.1.50 smtp smtp netmask 255.255.255.255
public static tcp (indoor, outdoor) interface https 192.168.1.50 https netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 9850 192.168.1.50 9850 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 1677 192.168.1.50 1677 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 7205 192.168.1.50 7205 netmask 255.255.255.255
clear xlate
Your final static config should look like this...
public static xxxx.170.20 (Interior, exterior) 192.168.1.30 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 192.168.1.50 smtp smtp netmask 255.255.255.255
public static tcp (indoor, outdoor) interface https 192.168.1.50 https netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 9850 192.168.1.50 9850 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 1677 192.168.1.50 1677 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 7205 192.168.1.50 7205 netmask 255.255.255.255
I just wanted to add that it would be to disconnect all existing connections, but will not affect the routing.
-
I can't connect to a Server IPSec since the recent update to OS X 10.11.4. Older versions on other computers connect without any problems.
The same is true for iOS 9.3: it connects my iPhone 6s, while two iPads type 2 not.
Seems to be a result of the most recent updates. What can I do?
Best WR
FWIW, I don't know if you're aware, but Apple has released a new version of iOS 9.3 specially for iPad 2s. I don't know if you re-set them or if this solves your problem with them.
-
I want to connect via VPN on multiple networks
Secure VPN connection is finished locallyby the customer. Reason 412. The distance peerisno more answer.
Hello
Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads -
Difficulty accessing 1 remote desktop when connected with VPN
Hello world
I have an ASA 5505 and have a problem where when I connect via VPN, I can RDP into a server using its internal address but I can't RDP to another server using its internal address.
One that I can connect to a an IP of 192.168.2.10 and I can't connect to a a 192.168.2.11 on 3390 port IP address.
The two rules are configured exactly the same except for the IP addresses and I can't see why I can't connect to this server.
I am also able to connect to my camera system with an IP on port 37777 192.168.2.25 and able to ping any other device on the network internal.
I also tried ping he and Telnet to port 3390 without success.
Here is the config.
ASA 4,0000 Version 1
!
!
interface Ethernet0/0
switchport access vlan 3
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.2.2 255.255.255.0
!
interface Vlan3
nameif outside
security-level 0
10.1.1.1 IP address 255.255.255.0
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the OWTS-LAN-OUT object
10.1.1.10 range 10.1.1.49
network of the OWTS-LAN-IN object
Subnet 192.168.2.0 255.255.255.0
service of the RDP3389 object
service destination tcp 3389 eq
Description of DC
the object SERVER-IN network
host 192.168.2.10
network of the SERVER-OUT object
Home 10.1.1.50
network of the CAMERA-IN-TCP object
Home 192.168.2.25
network of the CAMERA-OUT object
Home 10.1.1.51
service object CAMERA-TCP
Service tcp destination eq 37777
the object SERVER-Virt-IN network
Home 192.168.2.11
network of the SERVER-Virt-OUT object
Home 10.1.1.52
service of the RDP3390 object
Service tcp destination eq 3390
Description of VS for Master
network of the CAMERA-IN-UDP object
Home 192.168.2.25
service object CAMERA-UDP
Service udp destination eq 37778
the object OWTS LAN OUT VPN network
subnet 10.1.1.128 255.255.255.128
the object SERVER-Virt-IN-VPN network
Home 192.168.2.11
the object SERVER-IN-VPN network
host 192.168.2.10
the object CAMERA-IN-VPN network
Home 192.168.2.25
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
implicit rule of access-list inside1_access_in Note: allow all traffic to less secure networks
inside1_access_in of access allowed any ip an extended list
outside_access_in list extended access allowed object RDP3389 any host 192.168.2.10
outside_access_in list extended access allowed object RDP3390 any host 192.168.2.11
outside_access_in list extended access allowed object CAMERA TCP any host 192.168.2.25
outside_access_in list extended access allowed object CAMERA UDP any host 192.168.2.25
pager lines 24
Enable logging
exploitation forest-size of the buffer 10240
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
local pool RAVPN 10.1.1.129 - 10.1.1.254 255.255.255.128 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT static destination SERVER-IN-VPN SERVER-IN-VPN (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN
NAT static destination of CAMERA-IN-VPN VPN-IN-CAMERA (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN
NAT static destination of SERVER Virt-IN-VPN-SERVER-Virt-IN-VPN (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN
!
network of the OWTS-LAN-IN object
NAT dynamic interface (indoor, outdoor)
the object SERVER-IN network
NAT (inside, outside) Shared SERVER-OUT service tcp 3389 3389
network of the CAMERA-IN-TCP object
NAT (inside, outside) static CAMERA-OFF 37777 37777 tcp service
the object SERVER-Virt-IN network
NAT (inside, outside) Shared SERVER-Virt-OUT 3390 3390 tcp service
inside1_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 10.1.1.2 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.2.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP
DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = SACTSGRO
Configure CRL
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet 192.168.2.0 255.255.255.0 inside
Telnet timeout 15
SSH 192.168.2.0 255.255.255.0 inside
SSH timeout 5
SSH version 2
SSH group dh-Group1-sha1 key exchange
Console timeout 15
dhcpd auto_config inside
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
username admin privilege 15 xxxxx encrypted password
attributes of user admin name
VPN-group-policy DfltGrpPolicy
type tunnel-group CTSGRA remote access
attributes global-tunnel-group CTSGRA
address RAVPN pool
IPSec-attributes tunnel-group CTSGRA
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:0140431e7642742a856e91246356e6a2
: end
Thanks for your help
Ok
So, basically, you set up the router so that you can directly connect to the ASA using the Cisco VPN Client. And also, the goal was ultimately only allow traffic to the LAN through the VPN Client ONLY connection.
It seems to me to realize that you have only the following configurations of NAT
VPN Client NAT0 / free of NAT / identity NAT
the object of the LAN network
Subnet 192.168.2.0 255.255.255.0
network of the VPN-POOL object
subnet 10.1.1.128 255.255.255.128
NAT static destination LAN LAN (indoor, outdoor) static source VPN-VPN-POOL
The NAT configuration above is simply to tell the ASA who don't do any type of NAT when there is traffic between the network 192.168.2.0/24 LAN and VPN 10.1.1.128/25 pool. That way if you have additional hosts on the local network that needs to be connected to, you won't have to do any form of changes to the NAT configurations for customer VPN users. You simply to allow connections in the ACL list (explained further below)
Failure to PAT
object-group network by DEFAULT-PAT-SOURCE
object-network 192.168.2.0 255.255.255.0
NAT automatic interface after (indoor, outdoor) dynamic source by DEFAULT-PAT-SOURCE
This configuration is intended just to replace the previous rule of PAT dynamic on the SAA. I guess that your router will do the translation of the ASA "outside" IP address of the interface to the public IP address of routers and this configuration should allow normal use of the Internet from the local network.
I suggest you remove all other NAT configurations, before adding these.
Control of the VPN clients access to internal resources
Also, I assume that your current VPN client is configured as full Tunnel. In other words, it will tunnel all traffic to the VPN connection, so that its assets?
To control traffic from the VPN Client users, I would suggest that you do the following
- Set up "no sysopt permit vpn connection"
- This will change the ASA operation so that connections through a VPN connection NOT allowed by default in order to bypass the ACL 'outside' interface. So, after this change, you can allow connections you need in the 'outer' interface ACL.
- Configure rules you need for connections from VPN clients to the "external" ACL interface. Although I guess they already exist as you connect there without the VPN also
I can't say this with 100% certainty, but it seems to me that the things above, you should get to the point where you can access internal resources ONLY after when you have connected to the ASA via the connection of the VPN client. Naturally take precautions like backups of configuration if you want to major configuration changes. If you manage remotely the ASA then you also also have the ability to configure a timer on the SAA, whereupon it recharges automatically. This could help in situations where a missconfiguration breaks you management connection and you don't have another way to connect remotely. Then the ASA would simply restart after that timer missed and also restart with the original configuration (as long as you did not record anything between the two)
Why you use a different port for the other devices RDP connection? I can understand it if its use through the Internet, but if the RDP connection would be used by the VPN Client only so I don't think that it is not necessary to manipulate the default port 3389 on the server or on the SAA.
Also of course if there is something on the side of real server preventing these connections then these configuration changes may not help at all.
Let me know if I understood something wrong
-Jouni
- Set up "no sysopt permit vpn connection"
-
Can connect via the VPN, but cannot see the files
I can connect via VPN to my company network, but the files do not arise under Vista. I have no problem to see them on my old Windows PC, so this is a specific problem of Vista. On my old system, just click on computer and it shows me my company on the network's records. No Vista - cannot find anywhere, even if I am connected via VPN. Where are they?
Hello
Since it is the network of the company, there is no way to know hwo security is configured, unless you are a computer scientist in society.
Not "mess up" your computer, first talking to the person in charge of VPN connections.
Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET
-
Cannot connect remotely via VPN since installing the new modem/router
Can anyone help please. Since the acquisition of a new router / modem I can no longer connect via VPN to my work PC remotely. It comes in I receive the error message. Can someone tell me if I need to change the settings for the new modem / router to access?
Hello Joanna,
Here are the steps you need to do first:
- Off static IP for my server and let the router assign IP address and changed the IP address of the port forward.
- Check the IP address because obviously, that changed when you plugged into the router again.
- Updated to the latest firmware for the router and NIC.
For more detailed troubleshooting you can refer to this link: troubleshooting common VPN related errors.
Let us know how it goes.
-
slow when they are connected via anyconnect VPN, ASA OS 9.0
Hi guys
My users are complaining that they are experience slowness when they are connected via vpn anyconnect for ASA os 9.x, 5 Mb files tikes 15 mts rough with them, even if these users also have a connection broadband on their place
any guy insight
Thank you
Hi Ibrahim.
My first suggestion to you is to follow the recommendations of Cisco, associated with latency problems.
hostname (config) #-group
attributes policy
hostname (config-Group-Policy) #webvpn
hostname (config-group-webvpn) select #svc dtls
hostname (config-group-webvpn) #svc df-bit-ignore enable
hostname (config-group-webvpn) #svc routing-filtering-ignore enable
hostname (config-group-webvpn) mtu #svc 1200
hostname (config-group-webvpn) #svc compression no(a more recent version, you can use the command "anyconnect" instead of "svc")
If after this the problem persists please let me know when is the right time to reproduce the problem and collect the balls, debugs and catches. I also need the current configuration of the SAA (see technology in a txt file)
Kind regards
Aditya
Please evaluate the useful messages.
-
Unable to connect via IP MX200
Hello world. I have a problem with point to point connectivity between two end points. We have 1 st MX200 endpoint that is registered in VCS with it's own sip uri and the second is independent endpoint connected via vpn. What 2nd endpoing person trying to make a call using the ip address of the connection to a 1 set and everything works fine. But when I try to make a call using 2nd connection ip address of endpoints only showing a few errors of sip. Between intellectual property is very well. We cannot save this 2nd endpoing for our VCS. What could be the problem and how can solve this problem?
Thank you
1 endpoint registered with its own SIP URI, then I guess the 2nd endpoint 1 calls endpoint using the URI and no IP (that would be the logical way to do)?
Since it seems that you are not using a VCS-C/VCS-E deployment, "Called to unknown IP addresses" must be on "Live" on the VCS.
Note also when calling an IP using SIP, IP address should be prefixed by something @ - 'something' can literally be absolutely anything, i.e. [email protected]/ * / _endpoint_IP_address.
/Jens
Please note the answers and score the questions as "answered" as appropriate.
-
Restrict users of financial reports in the workspace
I have a user who has access to a specific planning unit so that it can enter data for this unit.
The hierarchy is:
Entity
Dept1
Dept2
UnitA
UnitB.
In this scenario, the user is able to enter data into UnitA only. It works very well, but he can find financial reports that Dept1 and same entity.
How can I limit so that it can only view reports of UnitA.
Any suggestion would be appreciated.
This report created using Essbase connection? If so, this is the reason why it shows all the metadata. If you use a connection planning then he imitates the planning of the properties. However, you cannot make attribute declaration.
Concerning
Celvin Kattookaran
-
How/where are the financial reports stored on the file system of the server?
We recently lost a large part of our reports on our server. We cannot understand what the restore directory location in order to get these reports back. Where is the default directory for 11.1.2.2 financial reports? And in what format the reports are being saved?
EN reports can be found in the file system of the operating system (o/s), but the EMP workspace hierarchy (folders, tree, etc.) are stored in the database of repository Hyperion bi +.
On the system of operating system files, the reports are stored in RM1 folder under folder "C:\oracle\Middleware\user_projects\epmsystem1\ReportingAnalysis\data\RM1\root".
The names of the reports placed here are UUID (identifiers of long - not the actual names).
For example:
When a report is created with the name 'My report' in Studio Financial Reporting, by connecting to the EMP workspace will be available in the name of financial reports/folder where it was saved.
the actual report will be stored in a subfolder of the RM1\root folder on the file system.
The file name will be a unique identifier (not the real name of the report is 'my report')
It will be generated 'on the fly' based on various things such as the date and time on the server (i.e. 0000012f5af72b1a-0000-ec71-c0a8006c.00000130510b77bb-0000-5133-c0a8006c.1)
The meta-data for this report ('My report', that is in the folder in the workspace, the date of the change of the report, permissions on this report, etc) will be stored in the Hyperion bi + DB as an object in an encrypted table. Financial reporting knows what metadata in the Hyperion bi + DB which corresponds to the report, in the file 'RM1\root' because all rows in the table for that object in the Hyperion bi + PB related to 'My report' will be referenced using the UUID of the file (for example 0000012f5af72b1a-0000-ec71-c0a8006c.00000130510b77bb-0000-5133-c0a8006c.1)
Note: The location of the folder of RM1 differs with each facility's operating system.
-
Are the "Oracle Hyperion Reporting and Analysis" and "Oracle Hyperion Financial Reporting," one and the same product?
Alanysis and Hyperion reports has a scope of report include Hyperion Finanicial Reporting, web analytics services RA framework and the Foundation as a layer application and client level there EMP Workspace, SmartView etc.
Thank you
~ KKT ~.
-
Hyperion Financial Reporting-Print Service is not running - put 11.1.2.1
We use the Hyperion 11.1.2.1 and when I look at my Hyperion Financial Reporting-Print service, it shows me to stop and when I right click to stop/start it the options are grayed out.
I completely stopped all services of hyperion and them began and now the HFR print service shows me as departure.
Kindly help me what should I do to solve this problem.
Hello
There should be a newspaper available that can give more indication to this problem, not being is not able to connect to the web server en is one of the common issues.
\FinancialReportingStudio\diagnostics\logs\FinancialReporting\FRPrintLogging.log try running the FRRemovePrintServer.cmd the Hyperion Financial reporting - Print serivce deleted successfully and run FRSetupPrintServer.cmd to add
check if it is releated to the firewall. Make sure that the ports are open.
Thank you
~ KKT ~.
-
Migrator for financial reporting
HelloYou have a Migrator for financial reporting? We export financial V11.1.1.2 reports and we import to V11.1.1.4. The import/export process fails because we copy V11.1.1.2 to V11.1.1.4. Reports migrated through a Java Exception and create duplicate database connections.
Thank you
Jean
Hello
We have a utility that can be executed in the same identical version which introduced from 11.1.1.3 on words of migration of LCM.
If you use the Import/Export to migrate EN is 11.1.1.2 11.1.1.4, you must create database connections in the new environment (the same as 11.1.1.2 with but servers are pointing to 11.1.1.4) first then you import 11.1.1.2 reports to avoid creating duplicate database connections.
In your case EN some reports after migration its pointing to old server (11.1.1.2) instead of 11.1.1.4.
Hope that help information.
Kind regards
Harish.
Maybe you are looking for
-
I've got dust under my camera lens cover!
So, as I said, I have a few dust particles under my rear camera lens cover (the small round glass piece located at the back of the phone, covering my cam). I think that's it through the microphone next to the camera, but I do not know how to remove i
-
My laptop Toshiba there input HDMI?
My laptop Toshiba there input HDMI?I was wondering because I want to play my xbox one on it.
-
Satellite L300D - necessary recovery image
Hello I'm trying to restore my laptop to factory settings. It's a Toshiba Satellite L300D and recently it has been infected by the virus of security 2011 windows vista.It still works in SafeMode with networking, and safe mode but I n t want to run th
-
noise problem of Y430 while using linux!
Hi guys,. I just installed ubuntu on my laptop 5342 y430 using wubi. While you are using ubuntu, sometimes, I made mistake, my laptop has issued some loud sounds like a siren of the car. This problem also occurs even if I'm running a Linux OS on VMwa
-
Hello. I use NI9512 with the cRIO-9074 and engine P70530 stepper drive. cRIO needs a power supply. And if I understand right NI9512 both P70530 need external power. So, I need 3 power supplies? Or NI9512 and P70530 need only one plugged into the netw