Firewall Windows with advanced security and mmc microsoft management console

Similar Questions

• Firewall Windows with advanced security rules do not take effect immediately?

  Hello everyone, I seem to have a problem with the Windows Firewall with advanced security. I put a rule that should prevent some IP address the ability to send packets to any port on my pc, however, it doesn't seem to work, said ip was still able to send packets until I installed the third-party firewall. That's what 'the netsh advfirewall firewall show = rulename rule name' indicates:

  Activated: Yes
  Direction: in
  Profiles: Domain, private, Public
  Group:
  LocalIP: all
  RemoteIP: x.x.x.x/32
  Protocol: all
  Traversed side: No.
  Action: block
  Protocol used to send packets was UDP.
  Is it normal that the rules from windows firewall do not take effect immediately?

  Thanks for the reply, I checked the Windows Firewall service, it is set to automatic, and two long-term services are started (BFE and MPSDRV). It turns out that the PC was connected to the Public network, while the Windows Firewall has been enabled only for the private profile. Activation of the firewall for the public profile, did the trick.

  Thanks for your comments.

• Firewall Windows with advanced security on Windows 8, lack of predefined rules

  I only noticed the problem initially because the network discovery is disabled, and no matter what I did I could not turn it back on. The necessary services were already running and I could navigate manually to other computers on the network, but they could not see or have access to the mines. I went and checked the Windows Firewall and found that there are no rules, at all. Disable Windows Firewall allows me to turn on discovery network without any problems. Well, I like to keep my operational firewall. After searching online, run the SFC system (with no results), I read that I could use "netsh advfirewall reset" to restore the predefined rules, but I am welcomed the error "a WF (0x3) fatal error has occurred." If it is a virus, I can't find it. Any help is greatly appreciated!

  I found a solution.  Thank you Google.  Sorta scary things hard like that, unknown people but I backed up and it worked:

  http://MajorGeeks.com/tweaking.com_-_Repair_Windows_Firewall_d7237.html
  "After running it (and the boy he gets busy), I could leave"Advanced settings"in the firewall configuration panel 'Restore default policy' and ' import policy" to load one that I could get by exporting it from my backup kicked.  At least now it seems OK and I was able to get us back on the network and turn on sharing.
  This demonstrates a real problem with services like these that you can export only the information an initialized backup and running and not some kind of configuration file that could be found from a mounted backup.  Windows is full of that kind of stuff.

• How to Access Manager for devices in the Windows 7 Ultimate Computer of the Microsoft Management Console (mmc) or Windows XP Professional computer using the computer (compmgmt.msc) management?

  I want to access Device Manager on a Windows 7 Ultimate remote computer from a computer running Windows XP Professional.  Whenever I have use (compmgmt.msc) computer management and access the remote computer, I connect successfully to it.  But when I select the Device Manager it says: 'access denied '.  I checked the security policy (secpol.msc) and I chose the deny access to this computer from the network and there no users and groups listed but it says that its default value is invited.  Can you tell me the step by step procedure?

  Thank you.

  In addition to changes to the GP, you must also do the following.

  Open services.msc, locate the "Remote registry" service, start the service and set to start automatically.

• How can I get my diagnosis Sevice policy running after being stoped in the Microsoft Management Console (MMC) console?

  Services in my MMC (Microsoft Management Console) has been tampered with and now services such as Diagnostic Policy Service left running. I tried everything I know to do and I'm still stuck. How can I get my Diagnostic Policy Service is running again?

  Hi sabraneal,

  ·         What version of the operating system is installed on the computer?

  ·         Have what troubleshooting measures you tried?

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow these steps:

  (a) click Start, type services in the search box of start and press to enter.

  (b) scroll down and select the Diagnostic Policy Service.

  (c) double click and start the service.

  Method 2: Scan the file system (CFS) auditor to repair corrupted files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 3: Also check if the computer is in normal startup mode. Follow these steps:

  one), click on Start, run and type msconfig then press on enter.

  (b) on the general tab , the startup selection should be the normal startup mode.

  (c) click on apply and OK.

  (d) restart the system.

• System refresh actualisations Microsoft Windows Firewall software with advanced opions not found

  Good evening

  When I ask the firewall with advanced fire windows I get the following response: failed to load the snap-snap-in windows firewall with advanced security code error 0xd9 options.

  Thanks for your insights.

  Best regards

  Guy PASCAL

  Please select your language from the drop-down menu at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below:

  Please get your language in the drop-down list above pour post your question in the language of your choice. The forum you posted is in English only. If you can't find the language of your choice above, options of fees to pay to other international destinations can be found by following the link below: (en)

  http://support.Microsoft.com/common/international.aspx

• Microsoft Management Console error: this function is not supported on this system. Also noticed that the automatic updates did not install it and returned error 80070005.

  Original title: Microsoft Management Console this feature only is not supported on this system

  I am running Vista 32 bit Business since an administrator account.

  Recently, I noticed that the automatic updates did not install it and returned error 80070005.   After investigation, I found that I could not open mmc at all and always get the message "this function no is not supported on this system.  No major changes have been made to the configuration to trigger it and I can't watch the event log because it is in the MMC.
  I have studied this question in line and tool the following actions, which none worked:
  carried out a complete antivirus scan (I use Commodo internet security)
  created another account administrator
  has run SFC (no problem)
  has run the registry cleaner (no problem)
  has run msconfig.exe and disabled all the startup process
  updated windows right click and run as administrator
  Started in safe mode and tried all above
  After that, I don't know where to go... it doesn't seem to be a download for Windows vista to reinstall mmc.
  I have about 50 updates critical, sitting in my windows update that can not install because of this problem.  Can anyone help?
  Jeff

  Hello Helpmehelpme,

  First, I would check since it is professional Vista was that computer on a field of work or it was already on an area of work? There may be group policies that are in place that prevent to run MMC.

  When did start to happening? Is there anything new on the system which has been introduced into the environment (software, hardware)?

  This thread gives a few steps trying to the original poster that you can't have.

• Windows 7 Microsoft Management Console has stopped working

  I am trying to open and print an element using AdobeReader, I updated my version of adobe in the last week or two. So, I'm pretty sure I have the latest version. When I looked for a solution for the following error message "Adobe Acrobat: AcroRd32.exe - Application Error" with the message "the instruction at 0x66882553c referenced memory at 0x0b6a4234. The memory could not be read. Click OK to complete the program"and was conducted to check my event viewer. I found this file on my computer and when I clicked it, I got an error message saying 'Microsoft Management Console has stopped working' and 'Windows is common for a Solution to the problem. However he never gave me a solution or even a propblem as possible. I investigated further on this site and found help advising me to open my services.msc in the start window and locate the event viewer. This is where my problem is that I can't locate event viewer in this particular window. Can someone help me?

  Hello

  1. Remember to make changes before this problem?

  Method 1: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 2:  Put the computer to boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link

• What are the tasks we can perform by using Component Services in the Microsoft Management Console?

  Original title: use MMC

  Can someone enlighten me on component services, found in the administrative tools, including the management console folder. Is their anything that can be done by someone who has no knowledge on this subject, extensive Windows, I use XP (SP3) thank you.

  Hi ratchet.

  Microsoft Management Console (MMC) lets system administrators create much more flexible user interfaces and customize administration tools.

  See this link for the tasks that we can perform using Component Services in the Microsoft Management console.

  With Component Services, administrators can deploy and administer service applications of components through a graphical user interface or automate administrative tasks using a programming or scripting language. Software developers can use Component Services to visually configure routine component and behavior of the application, such as security and participation in transactions, and to integrate components into Component Services applications.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_start_mmc.mspx?mfr=true

  Also check out this link:

  Using the Microsoft Management Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_start_mmc.mspx?mfr=true

• Microsoft Management Console has stopped working,

  When I try to open the Services get Microsoft Management Console stopped working.

  I ran sfc and has problems with mshtml.dll, among other files.

  This is part of the log:

  2011-07-29 09:00:29, info CSI 00000302 [SR] cannot repair the military record [l:20 {10}] "mshtml.dll" Microsoft-Windows-IE-HTMLRendering, Version 9.4.8112.16430, pA = PROCESSOR_ARCHITECTURE_AMD64 = (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, type neutral, TypeName neutral, neutral to the public key in the store, hash mismatch "
  2011-07-29 09:00:29, info CSI 00000303 [SR] this element is referenced by [l:156 {78}] "' Package_1_for_KB2530548 ~ 31bf3856ad364e35 ~ amd64 ~ ~ 9.4.1.0.2530548 - 12_neutral_GDR" "
  2011-07-29 09:00:29, info CSI 00000304 hashes for Member file? \C:\Windows\System32\mshtml.dll are not real file [l:20 {10}] "mshtml.dll": "
  Found: {l:32 b:NShyYjBbIUChbBY5LiLjFoB6/ekwlW/ef28uyjRQlLc =} expected: {l:32 b:oos9UuuZfvXEyFunl + vncI2DvnVD + Vo8pSj1iBJSVno =}
  2011-07-29 09:00:29, info CSI 00000305 Member \SystemRoot\WinSxS\amd64_microsoft-windows-ie-htmlrendering_31bf3856ad364e35_9.4.8112.16430_none_87d580a7f4d64061\mshtml.dll file hashes are not actual file [l:20 {10}] "mshtml.dll": "
  Found: {l:32 b:NShyYjBbIUChbBY5LiLjFoB6/ekwlW/ef28uyjRQlLc =} expected: {l:32 b:oos9UuuZfvXEyFunl + vncI2DvnVD + Vo8pSj1iBJSVno =}
  2011-07-29 09:00:29, info CSI 00000306 [SR] could not reproject corrupted file [ml:520 {260}, l:46 {23}] '------? \C:\Windows\System32"\[l:20{10}]"Mshtml.dll '; source file in the store is also corrupted
  2011-07-29 09:00:29, info CSI 00000307 Member \SystemRoot\WinSxS\amd64_microsoft-windows-ehome-font_31bf3856ad364e35_6.1.7600.16385_none_2ad6e90ee30ff985\WTVGOTHIC-S.ttc file hashes are not actual file [l:30 {15}] "WTVGOTHIC - S.ttc":
  Found: {l:32 b:UDL8t478X0i2FBeJvYbiU8O9Mo7RBSbqJnxsQ5q2Wmo =} expected: {l:32 b:dzS / rYReIjLpeofj7jo1l6q + cqg4X64ygEv2P/Dh6uo =}
  2011-07-29 09:00:29, info CSI 00000308 [SR] cannot repair the military record [l:30 {15}] "WTVGOTHIC - S.ttc" Microsoft-Windows-ehome-police, Version 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 = (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, type neutral, TypeName neutral, neutral to the public key in the store, hash mismatch
  2011-07-29 09:00:29, info CSI 00000309 [SR] this element is referenced by [l:176 {88}] "" Microsoft-Windows-MediaCenter Package ~ 31bf3856ad364e35 ~ amd64 ~ ~ 6.1.7601.17514.MediaCenter ' "
  2011-07-29 09:00:29, CSI 0000030 has hashes for Member file Info? \C:\Windows\ehome\WTVGOTHIC-S. TTC is not actual file [l:30 {15}] "WTVGOTHIC - S.ttc":
  Found: {l:32 b:UDL8t478X0i2FBeJvYbiU8O9Mo7RBSbqJnxsQ5q2Wmo =} expected: {l:32 b:dzS / rYReIjLpeofj7jo1l6q + cqg4X64ygEv2P/Dh6uo =}

  As is the only PC Win7 I can't copy files from another PC.

  Event poster mmc.exe exception 0xc0000005 Viewer.

  Name of the failing application: mmc.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc808
  The failed module name: unknown, version: 0.0.0.0, time stamp: 0x00000000
  Exception code: 0xc0000005
  Offset: 0x0000000006ab0000
  ID of the process failed: 0xa3c
  Start time of application vulnerabilities: 0x01cc4d7f99523eb5
  The failing application path: C:\Windows\system32\mmc.exe
  Path of the failing module: unknown
  Report ID: d7710ba3-b972-11e0-892a-1c6f65adf7ec

  I tried to restore to restore both points before, when I think that the problem began, but it did not help, so I undid the restorations.

  Help appreciated.

  Sue

  Win7 Professional 64 bit.

  He seemed to be solved by an automatic update.

• How to install the Microsoft Management Console?

  Hello

  I have a Satellite (S1800-412) with Win XP.
  Now I need to install the Microsoft Management Console on, but I have not possibility, because I have only Toshiba CD-ROM product recovery.

  to install the Microsoft Management Console, I should have the XP installation CD, but I did not.
  So my question is:
  What can I do with Toshiba CD-ROM product recovery to install on my satellite Microsoft Management Console?

  I'm trying to understand the policy of Microsoft and Toshiba, but it doesn't look good when I spend much for the XP system and I don't have the cd it wit.

  How can I solve my problem?

  I need to get an answer as soon as POSSIBLE!

  Concerning

  Stan

  Haha! It's easy:

  1. click on run.
  2. type in mmc.exe
  3. press enter
  4. There you are

  :)

  Where is my reward? (:)

• Is computer management the same as the Microsoft Management Console

  I've heard people refer to computer management in the MMC or Microsoft Management Console. What is the difference between the two, and why they are called the same thing?

  This should help explain it.

  http://en.Wikipedia.org/wiki/Microsoft_Management_Console

• Cannot open Microsoft Management Console mode author because of current computer policies

  Hello, I use Windows 7 Ultimate 64 bit.

  When I type "mmc", I get the following error. I am logged in as administrator.

  ---------------------------
  Microsoft Management Console
  ---------------------------
  You cannot open Microsoft Management Console mode author because of current computer policies.
  ---------------------------
  Ok
  ---------------------------

  Is this a normal behavior of the default Windows 7? If so, how to launch mmc or not if yes, how can I find the setting that causes this message?

  I found the parameter restrict access, which has been the Local computer policy > User Configuration > administrative templates > Windows components > Microsoft Management Console > prevent the user from author, Enabled.

  When I turned this option off, I could run mmc.

• Lack of updates - update for Windows Vista (KB2598479) security and an update of Cumulative security for Internet Explorer 9 for Windows Vista (KB2675157)

  I am running Vista/32 SP - 2.  2 updates fail - update security for Windows Vista (KB2598479) and updated security update Cumulative for Internet Explorer 9 for Windows Vista (KB2675157).  Downloaded and run Fix - It.  If the following message in the report - 'fix default locations of Windows Update does not work.  Wouldn't have known if I had not watched the details of reports since Fix - It said that everything had been fixed.  I tried to run Windows Update and Fix - It with the "run as Administrator".

  The suggestion of more optimistic that I see out there is reset the Windows Update components, but I have not been able to find out how to do this.

  I try next?  Thanks for the help!

  Hello

  1 did you change on your computer before this problem?

  2. what difficulty you are referring to?

  You can follow the suggestions and then check.

  Method 1

  You can download and run the system update readiness tool.

  Description of the update tool of the system to Windows Vista, Windows Server 2008, Windows Server 2008 R2
  http://support.Microsoft.com/kb/947821

  Method 2

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Method 3

  Step 1:

  Place the computer in a clean boot state.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a troubleshooting follow step 7: reset the computer to start as usual

  Step 2:

  Download and install the updates manually.

  Update security for Windows Vista (KB2598479)

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=28605

  A security update cumulative for Internet Explorer 8 in Windows Vista (KB2675157)

  http://www.Microsoft.com/download/en/details.aspx?ID=29357&WT.mc_id=rss_alldownloads_all

  See also:

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  You cannot install some programs or updates

  http://support.Microsoft.com/kb/822798

• Firewall Windows with Google Chrome problem

  Hello. Earlier today, I open Google Chrome and received one of these guests of firewall Windows that says "Google Chrome" tent of... I accidentally hit always block, instead of always accept and now I can't use Chrome. I get this message:

  NS lookup failed. DNS is the web service that translates the name of a Web site to its internet address. This error is most often caused by the presence of no connection to the internet or a misconfigured network. It can also be caused by a DNS server does not respond or a firewall preventing access to the network of Google Chrome.

  I tried the following, and none of them worked.

  (1) I added Google Chrome to the list of programs supported in Windows Firewall.

  (2) I restored the default settings of the firewall.

  (3) I did a system restore to yesterday.

  (4) I ran my anti-virus software.

  (5) I cleaned my dns cache.

  (6) I unchecked the "use DNS prefetch to improve page load performance" in Chrome.

  Nothing has worked. I know this has something to do with the fact that I told the firewall to block anything that Chrome was trying to do, but I can't seem to unlock!

  Can anyone help?

  Hello

  Because the problem is with Google Chrome I suggest you to post your query in the Google forum to improve assistance:

  http://www.Google.com/support/forum/p/chrome