Fixing bad block on the Win 2008 Server backup volume

Similar Questions

• Pass Cisco 871 and VPN to the SBS 2008 Server

  to precede the questions below, I'm responsible for COMPUTING internal with several years of site / offsite support. I also have very limited knowledge of the inner workings of a Cisco device. That said, I've beaten my head against a wall, trying to configure my router Cisco 871 to allow access to our internal server of SBS 2008 VPN hosting services. I think I, and properly configured the SBS 2008 Server.

  I use advanced IP services, version 12.4 (4) T7

  Here is the \windows\system32\conifg\system running

  Building configuration...

  Current configuration: 9414 bytes
  !
  version 12.4
  no service button
  tcp KeepAlive-component snap-in service
  a tcp-KeepAlive-quick service
  horodateurs service debug datetime localtime show-timezone msec
  Log service timestamps datetime localtime show-timezone msec
  encryption password service
  sequence numbers service
  !
  hostname yourname
  !
  boot-start-marker
  boot-end-marker
  !
  Security of authentication failure rate 3 log
  Passwords security min-length 6
  logging buffered debugging 51200
  recording console critical
  enable secret 5 *.

  !
  No aaa new-model
  !
  resources policy
  !
  PCTime-5 timezone clock
  PCTime of summer time clock day April 6, 2003 02:00 October 26, 2003 02:00
  IP subnet zero
  no ip source route
  IP cef
  !
  !
  !
  !
  synwait-time of tcp IP 10
  no ip bootp Server
  "yourdomain.com" of the IP domain name
  name of the IP-server 65.24.0.168
  name of the IP-server 65.24.0.196
  property intellectual ssh time 60
  property intellectual ssh authentication-2 retries
  inspect the IP name DEFAULT100 appfw DEFAULT100
  inspect the IP name DEFAULT100 cuseeme
  inspect the IP name DEFAULT100 ftp
  inspect the IP h323 DEFAULT100 name
  inspect the IP icmp DEFAULT100 name
  inspect the IP name DEFAULT100 netshow
  inspect the IP rcmd DEFAULT100 name
  inspect the IP name DEFAULT100 realaudio
  inspect the name DEFAULT100 rtsp IP
  inspect the IP name DEFAULT100 sqlnet
  inspect the name DEFAULT100 streamworks IP
  inspect the name DEFAULT100 tftp IP
  inspect the IP udp DEFAULT100 name
  inspect the name DEFAULT100 vdolive IP
  inspect the name DEFAULT100 http urlfilter IP
  inspect the IP router-traffic tcp name DEFAULT100
  inspect the IP name DEFAULT100 https
  inspect the IP dns DEFAULT100 name
  urlfilter IP interface-source FastEthernet4
  property intellectual urlfilter allow mode on
  urlfilter exclusive-area IP Deny. Facebook.com
  refuse the urlfilter exclusive-domain IP. spicetv.com
  refuse the urlfilter exclusive-domain IP. AddictingGames.com
  urlfilter exclusive-area IP Deny. Disney.com
  urlfilter exclusive-area IP Deny. Fest
  refuse the urlfilter exclusive-domain IP. freeonlinegames.com
  refuse the urlfilter exclusive-domain IP. hallpass.com
  urlfilter exclusive-area IP Deny. CollegeHumor.com
  refuse the urlfilter exclusive-domain IP. benmaller.com
  refuse the urlfilter exclusive-domain IP. gamegecko.com
  refuse the urlfilter exclusive-domain IP. ArmorGames.com
  urlfilter exclusive-area IP Deny. MySpace.com
  refuse the urlfilter exclusive-domain IP. Webkinz.com
  refuse the urlfilter exclusive-domain IP. playnow3dgames.com
  refuse the urlfilter exclusive-domain IP. ringtonemecca.com
  refuse the urlfilter exclusive-domain IP. smashingames.com
  urlfilter exclusive-area IP Deny. Playboy.com
  refuse the urlfilter exclusive-domain IP. pokemoncrater.com
  refuse the urlfilter exclusive-domain IP. freshnewgames.com
  refuse the urlfilter exclusive-domain IP. Toontown.com
  urlfilter exclusive-area IP Deny .online-Funny - Games.com
  urlfilter exclusive-area IP Deny. ClubPenguin.com
  refuse the urlfilter exclusive-domain IP. hollywoodtuna.com
  refuse the urlfilter exclusive-domain IP. andkon.com
  urlfilter exclusive-area IP Deny. rivals.com
  refuse the urlfilter exclusive-domain IP. moregamers.com
  !
  policy-name appfw DEFAULT100
  http request
  port-bad use p2p action reset alarm
  port-abuse im action reset alarm
  Yahoo im application
  default action reset service
  service-chat action reset
  Server deny name scs.msg.yahoo.com
  Server deny name scsa.msg.yahoo.com
  Server deny name scsb.msg.yahoo.com
  Server deny name scsc.msg.yahoo.com
  Server deny name scsd.msg.yahoo.com
  Server deny name messenger.yahoo.com
  Server deny name cs16.msg.dcn.yahoo.com
  Server deny name cs19.msg.dcn.yahoo.com
  Server deny name cs42.msg.dcn.yahoo.com
  Server deny name cs53.msg.dcn.yahoo.com
  Server deny name cs54.msg.dcn.yahoo.com
  Server deny name ads1.vip.scd.yahoo.com
  Server deny name radio1.launch.vip.dal.yahoo.com
  Server deny name in1.msg.vip.re2.yahoo.com
  Server deny name data1.my.vip.sc5.yahoo.com
  Server deny name address1.pim.vip.mud.yahoo.com
  Server deny name edit.messenger.yahoo.com
  Server deny name http.pager.yahoo.com
  Server deny name privacy.yahoo.com
  Server deny name csa.yahoo.com
  Server deny name csb.yahoo.com
  Server deny name csc.yahoo.com
  audit stop trail
  aol im application
  default action reset service
  service-chat action reset
  Server deny name login.oscar.aol.com
  Server deny name toc.oscar.aol.com
  Server deny name oam - d09a.blue.aol.com
  audit stop trail
  !
  !
  Crypto pki trustpoint TP-self-signed-1955428496
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1955428496
  revocation checking no
  rsakeypair TP-self-signed-1955428496
  !
  !
  TP-self-signed-1955428496 crypto pki certificate chain
  certificate self-signed 01
  308201B 8 A0030201 02020101 3082024F 300 D 0609 2A 864886 F70D0101 04050030
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 31393535 34323834 6174652D 3936301E 170 3032 30333031 30303035
  33315A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 39353534 65642D
  32383439 3630819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  8100CB6B E980F044 5FFD1DAE CBD35DE8 E3BE2592 DF0B2882 2F522195 4583FA03
  40F4DAC6 CEAD479F A92607D4 1 B 033714 51C3A84D EA837959 F5FC6508 4D71F8E6
  5B124BB3 31F0499F B0E871DB AF354991 7D45F180 5D8EE435 77C8455D 2E46DE46
  67791F49 44407497 DD911CB7 593E121A 0892DF33 3234CF19 B2AE0FFD 36A640DC
  2 010001 HAS 3 990203 AND 77307530 1 130101 FF040530 030101FF 30220603 0F060355 D
  1104 1B 301982 17796F75 726E616D 652E796F 7572646F 6D61696E 2E636F6D 551D
  301F0603 C 551 2304 18301680 145566 4581F9CD 7 5F1A49FB 49AC9EC4 678908FF
  2A301D06 04160414 5566 745 81F9CD5F 1A49FB49 AC9EC467 8908FF2A 03551D0E
  300 D 0609 2A 864886 818100B 3 04050003 903F5FF8 A2199E9E EA8CDA5D F70D0101
  60B2E125 AA3E511A C312CC4F 0130563F 28D3C813 99022966 664D52FA AB1AA0EE
  9A5C4823 6B19EAB1 7ACDA55F 6CEC4F83 5292 HAS 867 BFC65DAD A2391400 DA12860B
  5A 523033 E6128892 B9BE68E9 73BF159A 28D47EA7 76E19CC9 59576CF0 AF3DDFD1
  3CCF96FF EB5EB4C9 08366F8F FEC944CA 248AC7
  quit smoking
  secret of username admin privilege 15 5 *.

  !
  !
  Policy-map sdmappfwp2p_DEFAULT100
  !
  !
  !
  !
  !
  !
  interface FastEthernet0
  !
  interface FastEthernet1
  !
  interface FastEthernet2
  !
  interface FastEthernet3
  !
  interface FastEthernet4
  Description $$$ FW_OUTSIDE$ $ES_WAN$ ETH - WAN
  address IP dhcp client id FastEthernet4
  IP access-group 101 in
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  NAT outside IP
  inspect the DEFAULT100 over IP
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  sdmappfwp2p_DEFAULT100 of service-policy input
  out of service-policy sdmappfwp2p_DEFAULT100
  !
  interface Vlan1
  Description $ETH - SW - LAUNCH$ $INTF - INFO - HWIC-$4ESW $ES_LAN$ $FW_INSIDE$
  the IP 192.168.0.1 255.255.255.0
  IP access-group 100 to
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly
  route IP cache flow
  IP tcp adjust-mss 1452
  !
  IP classless
  !
  !
  IP http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  the IP nat inside source 1 list the interface FastEthernet4 overload
  IP nat inside source static tcp 192.168.0.100 1723 1723 interface FastEthernet4
  IP nat inside source static tcp 192.168.0.100 25 25 FastEthernet4 interface
  IP nat inside source static tcp interface 192.168.0.100 80 80 FastEthernet4
  IP nat inside source static tcp 192.168.0.100 interface FastEthernet4 443 443
  IP nat inside source static tcp 192.168.0.100 interface FastEthernet4 987 987
  !
  recording of debug trap
  Note access-list 1 INSIDE_IF = Vlan1
  Remark SDM_ACL category of access list 1 = 2
  access-list 1 permit 192.168.0.0 0.0.0.255
  access-list 100 remark self-generated by the configuration of the firewall Cisco SDM Express
  Access-list 100 = 1 SDM_ACL category note
  access-list 100 deny ip 255.255.255.255 host everything
  access-list 100 deny ip 127.0.0.0 0.255.255.255 everything
  access ip-list 100 permit a whole
  access list 101 remark self-generated by the configuration of the firewall Cisco SDM Express
  Note access-list 101 = 1 SDM_ACL category
  access-list 101 permit tcp any any eq 1723
  access-list 101 permit tcp any any eq 987
  access-list 101 permit tcp any any eq 443
  access-list 101 permit tcp any any eq www
  access-list 101 permit tcp any any eq smtp
  access-list 101 permit udp host 65.24.0.169 eq field all
  access-list 101 permit udp host 65.24.0.168 eq field all
  access-list 101 permit udp host 24.29.1.219 eq field all
  access-list 101 permit udp host 24.29.1.218 eq field all
  access-list 101 permit udp any eq bootps any eq bootpc
  access-list 101 deny ip 192.168.0.0 0.0.0.255 any
  access-list 101 permit icmp any any echo response
  access-list 101 permit icmp any one time exceed
  access-list 101 permit everything all unreachable icmp
  access-list 101 deny ip 10.0.0.0 0.255.255.255 everything
  access-list 101 deny ip 172.16.0.0 0.15.255.255 all
  access-list 101 deny ip 192.168.0.0 0.0.255.255 everything
  access-list 101 deny ip 127.0.0.0 0.255.255.255 everything
  access-list 101 deny ip 255.255.255.255 host everything
  access-list 101 deny ip any one
  not run cdp
  !
  !
  control plan
  !
  connection of the banner ^ CCCCCAuthorized access only!
  Unplug IMMEDIATELY if you are not an authorized user. ^ C
  !
  Line con 0
  local connection
  no activation of the modem
  telnet output transport
  line to 0
  local connection
  telnet output transport
  line vty 0 4
  privilege level 15
  local connection
  transport input telnet ssh
  !
  max-task-time 5000 Planner
  Scheduler allocate 4000 1000
  Scheduler interval 500
  end

  All that top has been configured with the SDM interface. I hope someone here can take a look at this and see what my question is, and why I can't connect through the router.

  All thanks in advance to help me with this.

  Jason

  Based on your description, I am assuming that you are trying the traffic PPTP passthrough via the router 871, and the PPTP Protocol ends on your SBS 2008 Server.

  If this is the correct assumption, PPTP uses 2 protocols: TCP/1723 and GRE. Your configuration only allow TCP/1723, but not the GRE protocol.

  On 101 ACL, you must add "allow accord any any" before the declarations of refusal:

  101 extended IP access list

  1 allow any one

  I guess that the PPTP control connection works fine? Are you able to telnet to the router outside the ip address of the interface on port 1723?

• Oracle 11 g 2 on WIN 2008 Server R2 on top of Citrix XenServer 5.5

  Hello
  
  According to the policies of Support Unbreakable Linux to virtualization and emulation:
  "Oracle products are not certified to run on the operating systems on top of Red Hat, Novell SLES or Citrix XenServer Enterprise Edition Xen hypervisors."
  
  This applies in my case: Oracle 11 g 2 on WIN 2008 Server R2 on top of Citrix XenServer 5.5 (or only if I have a Linux distribution installed on top of Citrix).
  And does that mean exactly?

  That is absolutely right.

  Nicolas.

• 10 gR2 on Win 2008 Server

  Hello
  is 10 cerificated gR2 on Win 2008 Server?
  
  Thank you.

  Yes, it is (but x 64)
  http://www.Oracle.com/technetwork/database/10204-winx64-Vista-Win2K8-082253.html

  Published by: Fran 29 - it is a-2011 05:56

• Win 2008 Server iSCSI San installation

  Hi, Im trying to install win server 2008 on a discovered iscsi lun. To do that I need to load my kmdf basic bus driver and one pilot iscsi initiator additional in order to discover the LUNs during installation.

  Win 2008 has 1.7 kmdf library by default. So to install 1.9 kmdf library in it, I added the Windows6 package. 0-KB970158 - x 86 .cab in the install.wim file. With this, the installation is complete. But when the operating system starts for the first time, my bus kmdf driver does not load completely. Only the Driverentry routine is called. EvtAddDevice routine is not called. So, accordingly, I see a BSOD saying that boot partition not found. Any kind of suspicion would be useful.

  This forum is for Vista.  I suggest you use the Technet Windows Server forums

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Bad blocks on the new drive

  I have a HUS724030ALE640 HGST fairly new (7 k 4000 3 GB Ultrastar) that shows an unusual number of bad blocks (107) for a new disk. I just bought 26 of them and the rest 0 defective. Should I guarantee return this puppy?

  Get information from the disk utility:

  Reallocated sector Count : 00000000006 B

  bad blocks has been published after use, or they were already there after unpacking?

  If the last: I wouldn't worry about 107 defective at all.

• LegeCy medical application requires administrator rights to run on Windows XP but application resides on the SBS 2008 Server

  Hi all

  Application is a medical Client / Server using SQL in the database model. and resides on the SBS 2008 with XP Server and client computers.

  Rather that to load the client on windows XP, it would not sense to simply run the application console using the Terminal Server services and configure the application to start an hour of connection on. Given that the application requires administrator rights to run, how can I assign admin right only on demand, so when they connect, they can use the application with the given admin rights but do not have access to the rest of the server or control?

  Been awhile and a very little bit of rust, but I know it should be easy... losing sleep reading my series of the voume of support docs... :)

  Hello

  The question you have posted is related to servers and will be well suited in the TechNet community. Click on the link below.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Boots only to the Startup Repair. Hardware diagnostics found bad blocks on the hard disk. is it possible to move data outside of Windows?

  Original title: Hi, I have a Dell Inspiron 1545 laptop.  Recently, he stopped working and would go only to the screen that asks if you want to run the Startup Repair tool.

  Of course whenever I launch it, it goes back to this screen.  Check the diagnostics through the F12 boot, I had three error codes: 0F00:1344, 0244 and 1 A 44.  These were all on the same three blocks.  The message was impossible to read, replace the drive.  I'm really the most responsible for recover my photos, documents, etc. and have an external hard drive.  Is it possible to do so, even if Windows (Vista in this case) will not start?

  Hello

  You can try these methods

  Data recovery

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed

  If this does not work, you may need to contact the data recovery specialists

• cannot log on to the domain Win 2008 Server using W7

  When I join domain he managed,

  but when I try to log on to a domain, that he has failed,

  There is place...

  When I get back the user name, password and press enter

  "Welcome...". »

  but at the point where its change to "end the session...". »

  hope you help me.

  When I join domain he managed,

  but when I try to log on to a domain, that he has failed,

  There is place...

  When I get back the user name, password and press enter

  "Welcome...". »

  but at the point where its change to "end the session...". »

  hope you help me.

  Hey catra abdessamad

  Here is the vista forums

  Repost in instances of server on the link below

  http://TechNet.Microsoft.com/en-us/WindowsServer/bb250589.aspx

  Walter, the time zone traveller

• I'm going to 2012 SQL file of the box and you want to run on Win 2008 Server. can you please how can I perform a unboxing conversion it

  I can how to perform a conversion unboxing of the file .box executed as for the installation of SQL 2012 .exe file.

  These MS Answers forums are intended for the home rather than the it professional user. Please transfer your question in the relevant Microsoft Technet forum here:

  http://social.technet.microsoft.com/Forums/en-us/categories/ .

  Thank you.  :)

  (I'm sorry, but I can't move this thread for you because the two forums are working on separate platforms)

• Effect of bringing a child to a Windows Server 2008 VDMK to an another Win 2008 Server

  I was looking for the product documentation, communities and delivery over the Internet, but I fear that I am using the wrong keywords.

  The trail has gone cold, and I'm here.  I work with the Client of VI 2.5.0.147704 connected to vCenter.

  SVR1 = I have a virtual machine with 2008 standard which has a C: partition for OS and a D: drive with data on 'the island '.

  SVR2 = I have another server with 2008 which was just a disc parent - the C: partition.

  All discs are in the same data store and I am responsible for the backup of my data before proceeding.

  I want to stop SVR1 and move the SVR2 VMDK, but I want to perform due diligence before making the move.

  I think I need to go to the correct data store and move the SVR1_1.vdmk of the SVR1 folder to the SVR2 folder.

  Then, I want to rename the VDMK of SVR1_1.vdmk to SVR2_1.vdmk.  Here are my questions...

  1 when I move the drive, can I just move the secondary image (the disk "_1") or do I need other files related to disk?

  2. when I boot SVR2, can I import the disk in Windows and assign it the letter D:?

  3. have I accounted for all the appropriate things associated with something like this?

  If someone is able and willing to help with this issue, any help would be appreciated.  Thank you.

  I practice the planned move. Use the stand-alone converter tool to make a copy of your destination server to a new virtual machine on the same ESXi host. COPY the VR1_1.vdmk on the newly created virtual machine and add the vmdk on the server. Change the settings to disconnect from the NETWORK card and test your virtual machine to make sure that the installation works as expected.

  The SVR1_1.vdmk that display you in the data store Navigator is actually composed of 2 files. The SVR1_1.vdmk is actually just a text file descriptor describing the vmdk. The data is actually stored in SVR1_1 - flat .vdmk, whereby it is not visible in the browser. When you do a copy to move the SVR1_1.vdmk using the browser data store both the SVR1_1.vdmk and the SVR1_1 - flat .vdmk file is moved or copied. If you use another tool or the command line to move or copy, you must make sure that you move or copy the two files.

  Adding a windows vmdk is no different than adding a disk on a physical machine. Once you have edited the machine virtual and added the disk, it will be automatically recognized by Windows. If you add HOT then you will need to use the Manager of Dick rescan the disks so that it is visible. It will automatically take the next drive letter as it would on a physical machine.

• Out with the old WinXP box in with Win 7 - recognition problems 2008 Server box

  Our box office WinXP was finally cut off (the last, all the others are Win 7).  I built a new area of Win 7/64 with Windows 7 Professional.  I was able to transfer all the old stuff from WinXP on the server by using the parameters of conduct transfer agent.

  I plugged the new Win 7 box and everything works fine.  However, I can't get our Win 2008 Server to recognize the new box.  User dave is there but the server does not see the new box.

  Q: should I remove user "dave", and then reinstall a new "dave" at the server level?  Seems that I would lose settings, etc. like this.

  I've been going through Hester and Henley on Admin book, but nothing comes out with me.

  If you have configured Active Directory, then you should be able to join your domain from the Windows 7 machine as you would for Windows XP. Please note that you may experience problems if your Local network connection is firewall, as well as temporarily disable and try again.

  http://www.notebooks.com/2009/11/11/quick-look-Windows-7-in-the-workplace-joining-a-domain/

• Satellite P10-304: bad sectors on the disk - how to fix?

  My drive HARD drive bad sectors developed and replacement needs, does anyone know how to do this?

  My model is a P10-304.

  In addition, Windows will not start upward in my old HDD because of bad sectors and the drive is protected by Norton and back, does anyone know how to bypass or disable round trip

  Hello

  I found these tips how to disable the Norto Go Back tool.
  You can uninstall it from your computer, disable GoBack to your laptop press 'space' GoBack screen button and select the option "disable" GoBack.

  Follow these steps:
  1. reboot your computer.
  2. when the Norton GoBack splash screen appears, press the SPACEBAR.
  3. in the Norton GoBack boot menu, click on disable.
  A message informs you that disable Norton GoBack erases history and you will not be able to run the hard drive or hard disk restore advanced restore until Norton GoBack is turned back on.
  4. click on Yes.
  5. click on continue.
  Your computer restarts automatically, and Norton GoBack is off
  After restarting the laptop, I recommend once again using the following key: CTRL + ALT + G.
  Immediately press on and hold the keys Ctrl + Alt + G after restarting the laptop you. A message you giving the possibility to force the removal of GoBack master boot record. Press F to force the removal of GoBack master boot record.

  If failure of keys Ctrl + Alt + G in the first time then try this again for three or four times until you get the prompt to remove the master boot record of GoBack.
  Finally, restart the computer.

  To fix bad sectors on the HARD drive, you could boot from the XP CD to use the console of "repair".
  And then use the CHKDSK /p command to repair the bad sectors.

  Good luck

• Satellite A300D-15B with driver Vista 32-bit for Win 2008 possible?

  Hi all

  I have a laptop A300D-15B, and recently I have installed Win 2008 (32 bit) and installed the Vista 32-bit drivers worked like dream. But when I install the card reader (O2) it crashes (blue screen)?

  has any one face this problem?

  any help?

  Thanks in advance

  concerning
  Ganesh

  > But when I install the card reader (O2) it crashes (blue screen)?
  Looks like this Vista driver is not fully compatible with Win 2008 Server and therefore you receive and BSOD

  Seems you have to use this operating system without this special driver

• Win 2003 server need drivers for my Satellite A100-785

  Recently, I bought this laptop and I tried to install windows 2003 server on it, of course the CD that came with the laptop has no drivers, so I tried to download the driver from the link below:

  http://Gulf.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  But I found the option for Setellite A100 (PASAAN), mine is Setellite A100 (PASAANE), with 'E' at the end! Any idea?

  Concerning

  Hello

  Don t worry!
  It's the same series: the PASAAN Satellite or Satellite A100 PASAANE.
  Only the E is missing.

  Regarding you drivers for Win 2003 server;
  The Toshiba provides no drivers specifically for the Win 2003 server operating system.
  But this operating system is based on Windows XP.

  So, try to download and install the XP drivers. These drivers must be compatible

  Greetings