FN keys based on Satellite Pro P200 with Windows XP

Similar Questions

• No sound in Satellite Pro P200 with XP

  Hi all.

  I have a Toshiba Satellite Pro P200 with Windows Vista preinstalled. I removed Vista and installed Windows XP with Service Pack 2, due to the incompabilités with some software I need. Almost all of the necessary drivers for XP (even a downgrade to BIOS) was downloaded and installed from Support from Toshiba web page. But there are still two devices that I can not install. At the start of my laptop it always detect "* Microsoft UAA bus driver for high definition audio *" and "* controller memory PCI - Chip for logical Cache Flash in Intel (r) *" as new hardware and they appear marked in yellow in the Device Manager list.

  I installed the last bus Microsoft UAA for high definition audio driver for XP from Toshiba and Realtek too... a lot of time and in different ways... Previously I installed the High Definition Audio Driver Package - KB888111 from Microsoft. But I still have no sound.

  PCI memory controller - Intel(r) Flash Cache Logic Chip: the same... tried the drivers the most recent Toshiba one Intel too. Toshiba technical support told me that this unit is ready to run on Vista and have suggested me to try with Robson drivers for Vista Support from Toshiba's web page, but that didn't work either.

  I googled a lot, searched this forum and called technical support, as I said, but I've not found a way to solve these problems. Really, I can't believe I bought a laptop that only works with Windows Vista, I resist assume this idea, so I continue to try and try to make it work properly with the operating system that I need and I have chosen freely.

  Any idea?

  Thanks in advance.

  Hello

  > I installed the last bus Microsoft UAA for high definition audio driver for XP from Toshiba and Realtek too... a lot of time and in different ways... Previously I installed the High Definition Audio Driver Package - KB888111 from Microsoft. But I still have no sound.

  You're on right way boyfriend, you must also install another patch MS; KB835221
  So finally the KB888111 and KB835221 must be installed before you will follow with the audio driver installation.

  Check this thread:
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=113124

  > PCI memory controller - Intel(r) Flash Cache Logic Chip: the same... tried the drivers the most recent Toshiba one Intel too. Toshiba technical support told me that this unit is ready to run on Vista and have suggested me to try with Robson drivers for Vista Support from Toshiba's web page, but that didn't work either.

  The problem is that this unit only works in Vista.
  The controller memory PCI is that intel Turbo Memory, also called Intel Flash cache logic chip also called device Robson.
  It's quite new technology designed to support the new features of Vista.
  There is not driver for it for Windows XP because XP doesn t supports the function of cache, it is supported by Vista.

  Hope I could help you

• Can I downgrade my Satellite Pro P200 for Windows XP?

  Hello

  I bought my Satellite Pro P200 (PSPB7E) a week ago and I love it. I have an unused XP license, so I would like to downgrade.

  Is this problem? I don't see xp for a Chicony webcam drivers or the HD-DVD player.
  I'd really appreciate some feedback. There must be someone out there who has tried to do.

  Thank you in advance!

  Hello

  Of course you can downgrade the satellite Pro P200 for Windows XP.

  When installing XP, you need to install the Intel Storage Manager. It is a SATA driver that is needed to activate the HARD disk.

  Regarding the webcam driver.
  I checked the page European driver of Toshiba and the Chicony webcam driver is certainly available.

  The HD DVD driver is not necessary because the Windows XP must use an own ODD driver.

  See you soon

• Satellite Pro P200 with WXP - two components without driver

  I installed XP Pro on my Satellite Pro P200 15W and I installed all the drivers on the driver download page, but I have still two components without driver: these devices, I don't know what types of devices are, because it seems that this medication works very well. The features are:

  Memory (Controladora de Memoria PCI) PCI controller
  Unknown device (unknown device)

  I aso installed upgrading Bios WIN5.00, but both devices still does not.

  Any idea?

  Thank you everyone

  The * PCI controller memory * Intel Turbo Memory is called a chip Flash cache logic Intel (Robson device).
  It s a new technology designed to support the new features of Vista.

  There is not driver for it for Windows XP because XP doesn t supports the function of cache, it is supported by Vista.

  The other unknown device could be everything; You may need to verify that the devices do not work. LAN, WLan, etc...

• No sound on Satellite Pro A120 with Windows Vista

  Hello

  I had to reinstall the Vista operating system and rebuild my Satellite Pro A120 from the revovery disk.
  Most of the things are fine, but I can't any sound to speakers of jack headphine.

  I checked said etil Realtek High Definition Sound Driver is installed and working properly.

  My volume buttons are up on the mixer and Windows Media Player.
  The driver is Realtek 6.0.1.5317

  Help would be appreciatesd

  Hello

  Please take a look here:

  + Audio cut off (no sound) after you install Windows Vista +.
  http://APS2.toshiba-tro.de/KB0/TSB7C021B0001R01.htm

  There is a tool that allows the sound again once it seems s Cup...

  Welcome them

• Re-construction of Satellite Pro A200 with Windows XP - how to

  Hello

  I am looking for help regarding some A200 that I just got.
  They came with Vista Home premium, but I try to rebuild their windows XP disks use.
  Once the start-up of the machines from the disk and asking to install windows XP, I get the following message:

  -------------------------------------------------------------------------------
  Setup did not find any hard drives installed in your computer.

  Make sure that the hard drives are powered on and properly connected
  to your computer and that any hardware configuration of the discs is
  fix. This may involve a diagnosis provided by the manufacturer running
  or Setup.

  Setup cannot continue. To quit Setup, press F3
  --------------------------------------------------------------------------------

  I tried to go into the BIOS to find the setting which you start using HDD settings simple alloys but this option does not seem to exist, is any body can help because it is a matter of urgency.

  Kind regards

  Kevin Bennett

  Hello

  It seems that you need the SATA driver!

  On the Toshiba page, you should find the Intel Storage Manager. It is a SATA driver and it should be included during the XP installation process by pressing the F6 key.

  Then, you could include it from the external disk to floppy drive

  If you don t have a FDD drive so that you can use free software called nLite

  By the way; Why you do not use the search option in this forum to search for similar topics...

• Installation of Windows XP on Satellite Pro P200

  Hi guys,.

  I have a problem installing Windows XP Home SP2 (listen Slip) edition in my new Satellite Pro P200 with 2-120 GB hard drives. The vehicle currently has windows vista professional. I followed this link to a similar question on this site: http://downloadcenter.intel.com/filter_results.aspx?strTypes=all&ProductID=2101&OS FullName = Windows * + XP + Professional & lang = eng & strOSs = 44 & submit = Go % 21 and created disk Intel Matrix Storage manager so that I could use "F6" to install the RAID drivers during the installation of XP.

  I got to the point where I was able to recognize the hard drive and I was able to select the partition where I wanted to install WXP. Once the NTFS partition has been selected and formatted, Windows XP Home edition Setup prompted me to insert "Intel Matrix Storage" diskette into the A: drive. I have this drive in my floppy USB drive.

  However he didn't even read the disc. Hard drive never turned on when I pressed the enter"" key. It seemed as if the installer froze, however I was able to push "F3" to exit the installation program. Can someone tell me what I'm doing wrong here? Is the USB problem?

  Help, please!

  I really put t understand those who wait and wait and wait for a solution instead of search here in this beautiful (forum) knowledge base for similar topics:

  Check this box:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=26040

• Problems after updating the BIOS on Satellite Pro P200

  I recently buy a Satellite Pro P200 running Windows Vista Business. Yesterday, I updated the BIOS to the version 1.50 supplied with the machine to 1.80 available on the Toshiba site. I double checked that I was using BIOS correct update for the Pro P200 Satellitel running Vista.

  After updating the BIOS, I have now two problems:

  1. whenever I start and join the office, I get an error message "record of Vista has stopped working". This problem has been identified as toshibavistaregistration.exe here: [link: http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=99805]

  2 Control Panel > system now shows the processor and the memory (RAM) as "not available". Execution of the diagnostic PC Toshoba tool and looking at basic information show also no information on the memory (RAM) Although the processor information here. There may be pieces others missing too under the eyes of list shorter than before the update of the BIOS.

  Basically, I want to get everything working again as it should, but cannot find any information on these issues.

  After further review, it appears that the update of the BIOS is not the cause of the problems.

  Immediately after updating the BIOS, I had a major system crash. It turns out that this is what has caused problems.

  After a system restore to a point before the update of the BIOS and the major system crash, now everything is working again with BIOS version 1.8 in place.

• Satellite Pro P200: Change the size of partition in Vista?

  Is it possible to adjust the size of the partition after installing?

  I have a Satellite Pro P200 with a shared about HARD disk:

  C: Vista partiton - 17 GB of free to 56 GB
  E: partition of data of-54 GB of free to 55 GB

  I know that the data reader is used by Vista to contain information of recovery.

  However, I would like to know if its possible to reallocate some of its spare production capacity at the Vista drive without compromising the recovery feature?

  Of course, you can change the size of the partitions after Vista installation.

  You can change this in the Vista Disk Manager s

  Here, you could choose the existing partition, and then you could reduce the amount of partitions. This free volume can be added to another partition, or you can create another partition.

• Satellite Pro P200 - parity memory error

  Hi all

  Sometimes, I get the following error message when I start my computer laptop http://www.geocities.com/atesfaye/Mar08_0001.jpg

  It's a Satellite Pro P200 with 2 x 1 GB RAM modules. I ran memtest on the memory installed together and individual modules. The results of the test came with no error. To read the different forums of discussion, some suggest that this error message may relate to graphics memory! Is there a way to test the graphics memory?

  Any help much appreciated!

  Can you tell us when this problem started?
  A has started after the upgrade RAM or other activity?

• Re: How can I add a second internal hard drive to a Satellite Pro P200?

  I have a Satellite Pro P200 with a single internal hard drive. There is a second Bay in the computer of another internal hard drive, but I couldn't find any information about it. There is enough space for a 2.5 "SATA but I do not see a connector.

  I contacted Toshiba Dutch customer service who said that it was official policy not to provide any information on a second internal drive. They also said that they would not provide parts to make it possible.

  Can anyone provide more information?

  Hello!

  I think that if there is no connector you cannot add a second HDD.
  It of Nice to have a second Bay, but it's nothing without a connector.

  Good bye

• Satellite Pro P200-HD: how to use it with Win XP

  Recently, I received the new Satellite Pro P200 HD of Getech. I asked Getech to change the XP operating system because my University will not support Vista. I was told that some features are lost with XP, such as the hot key utility and I agreed to go ahead.

  However, I was not informed that the sound is scratchy and the video will behave as if I play a scratched CD.
  It is true with windows sounds as well. I was not able to enjoy the music or video. I have all the drivers updated and the new Bios XP released recently has been updated.

  Please does anyone know someone using this model with XP as an operating system with the sound and video works properly?
  This would mean that I was sold a laptop with a defective sound equipment and should get a replacement because I had this problem from day one.

  Thanks for the help in advance.
  Calvin

  * @ Vivien *.

  How about this:
  http://EU.computers.Toshiba-Europe.com-> support download &-> download drivers

  There, you might choose the satellite Pro P200 to download XP drivers

• Problems with multitasking on Satellite Pro P200

  I am the owner of a new Satellite Pro P200.
  I use this laptop to use software such as photoshop, indesign, etc.

  * Now I have problems with multitasking! *
  It is not possible to run 3 programs at the same time.
  That I have to restart my laptop again and again.

  Does anyone know what is the problem?
  Can someone help me with this problem?

  For two weeks I have P200D. I use it for work and use different applications at the same time. So far, everything is OK and I am very satisfied. Maybe you should try to optimize the operating system:
  -remove all software, you do not need
  -disable the startup of unnecessary software of automatic startup (MSCONFIG)
  -customize the appearance
  -information on the open performance and Control Panel tools and use tasks on the left side to improve the performance of computer s

  P200 is powerful enough and must be able to manage with a few applications running at the same time.

• No software DVD player with my new Satellite Pro P200

  Just bought a new Satellite Pro P200 and, to my surprise and dismay, it has software player DVD No. inside? I downloaded the DVD drive on the official download here, but Vista abandoned the facility saying that I can not install the application. Have you tried to configure it as a Admin, but the same message is given running.

  Suggestions as to how I can get the software to run movies DVD on the new laptop computer would be most appreciated.

  The laptop is model is PSPB7E, it has Vista Business installed and has a HD-DVD drive installed.

  Would apprecate a response early to what I already plan to return this item, demanding a full refund since it seems that it does NOT use a software which SHOULD run (IE. Compatible versions of some software XP will simply not installed because Vista blocks!).

  Kamshot - discouraged by the new culture of 'Vista '!

  Hi Kam

  As far as I know every Toshiba laptop comes with pre-installed software allows you to watch DVD movies. It is a part of the standard installation and the application is called WinDVD.

  According to the specifications of the laptop, your laptop has no HD DVD player, just DVD-Super Multi (+ r DL). Because of this there is no HD DVD player.

  > Would apprecate a early response to what I already plan to return this item and requesting a full refund because it > seems that it does NOT use a software which SHOULD run

  No comments for this

• Satellite Pro P200 (Fn) keys

  PSPB7C-S030BC

  Hello, I recently downgraded my Toshiba Satellite Pro P200 from Vista to Windows XP. Everything works well except the function (Fn) keys to control the screen brightness, volume. Some function as mute but most do nothing when I try to use them. All the installed drivers although Device Manager shows errors or lack nothing.

  I tried to install all the drivers for the keyboard, the Fn keys, keyboard shortcuts, and still I can't work at all. Someone was able to get these keys to run after the installation of WinXP or you know what drivers/software I'm missing? These keys can be used in XP or they work only in Vista?

  Thank you.

  What you are missing BIOS is designed for Windows XP Home edition. This is the version 5.20. Visit the download page of the Toshiba BIOS under http://eu.computers.toshiba-europe.com > support & downloads > support home > update BIOS.

  Good luck!