Freescale in the LabVIEW ARM controller?

Similar Questions

• examples of LabVIEW ARM code

  Hello

  I am new to Labview ARM I used an ek-lm3s8962 Keil Committee.

  I would like to know if there are a few tutorials and code examples on communications with devices:

  How to write you SD card?

  How to use CAN, SPI, I2C and UART?

  How to use the OLED?

  Is it possible to use the FIFO memory with labview ARM and how?

  Is it possible to target the daughterboard with Labview, this Board includes a processor LM3S2110?

  How communicate between a time critical Vi which runs on the ARM processor and not time critical Vi host that runs on the PC?

  Thank you very much.

  Your Neil

  Hi Neil,

  How to write you SD card?

  The SD card slot only is not currently supported in point 1.1 of the ARM.  The next version of the ARM should support this device.  Once this is the case, you can access the SD card using the primitives of e/s files.

  How to use CAN, SPI, I2C and UART?

  I found an example of UART in the Finder for example OR in Modules and Toolkits > ARM > Luminary Micro > protocol drivers > Comm.lvproj series.  I will attach also a project that uses CAN communicate with the LMS2110.  As for I2C/SPI, I suggest experimenting with the screws for this (located on the ARM > palette SPI and I2C) and consultation of the other threads on the use of these screws or create another thread.

  How to use the OLED?

  There is an example of this in the Finder for example OR in Modules and Toolkits > ARM > Luminary Micro > Device Drivers > OLED.lvproj.

  Is it possible to use the FIFO memory with labview ARM and how?

  FIFO on ARM is very similar to the desktop.  These screws are located in the data Communication > synchronization > FIFO pallet in real time.  There are several examples on how to use these FIFO on ni.com.

  Is it possible to target the daughterboard with Labview, this Board includes a processor LM3S2110?

  You can provide this Commission with CAN, as shown in the attached draft.

  How communicate between a time critical Vi which runs on the ARM processor and not time critical Vi host that runs on the PC?

  See the related example. RT FIFO If you use the FIFO screws I mentioned above, you should be able to do something similar.  I suspect that the FIFO is used to communicate between a critical time timed loop and while loop a criticism.  The while loop would then use TCP/series (or even shared network variables) to communicate to the host.

  Good luck

• RT code works since the LabVIEW environment, but not when I create and deploy

  I think there are a lot of reasons why this can happen, but I can't seem to pin one.

  I have a classic controls program that runs on a cRIO. We recently decided to change the communication of a ProfiBus comsoft on Ethernet/IP card. (Industrial Protocol for Allen Renaud automata). For various reasons, we put the fuse in communication in the control loop.

  Now when I run the LabVIEW now, it works fine. I can see data going to and coming from the controller. I can sniff packets and they look good. I get about 30 milliseconds on the loop, which is long, but since I am running in the IDE, I think is not bad. (In other words, I get data in and out every 30 milliseconds).

  When I compile and set the binary on the cRIO, it breaks. I can still sniff packets, but what I'm getting now, is that all traffic to the controller of read requests. My write requests are missing. In addition to reading queries are poorly trained. Rather than ask 43 items in a table, they ask 1.

  A test that I tried was to disable the read request. For the binary file, I don't see any traffic. For the IDE, I see write queries.

  I use LV 2009 SP1. I have the version of NOR-Labs of the Ethernet/IP driver. (We have a request for a quote, but do not have the official driver.) In the meantime, faster I get this done, the happier everyone will be ;-)

  Any suggestions?

  Attention to the nodes of property which is usually my problem when it happens.  Some who say they work in RT do not work in compiled RT

• Satellite U840-113: pilot missing for the PCI Communications controller

  "* Toshiba Satellite U840-113 - PSU4SE: * Win7-Prof - 64-bit with MS-DVD original on off RAID, no RAID oder installed software RAID driver, internal SSD now like normal running, new installed SSD SSD completely new, all the drivers installed successfully - with the exception of the following device: in Device Manager, I find under the"other devices"the position?" Controller PCI-Communications (single) ". *

  Who can help me to locate / find the right driver for this "PCI Communications controller"?

  What ist this? Do I need this?
  The system seems to work perfectly; I disable this feature?

  Thanks a lot for the helpful answers!

  Hello

  This article from Toshiba may be useful:
  http://www.MyToshiba.com.au/support/items/FAQ/222

  The PCI of Simple Communications controller is part of Intel AMT Management Engine Interface and is related to the networking on your computer.

  You will need to install the driver Intel (r) AMT Management Engine Interface.

• need an exact model of the PCI communications controller driver

  Mr President.

  my model is G62 B39 SE

  WINDOWS 7

  64-BIT

  HARWARE ID IS

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C & REV_06

  PCI\VEN_8086 & DEV_3B64 & SUBSYS_1439103C

  PCI\VEN_8086 & DEV_3B64 & CC_078000

  PCI\VEN_8086 & DEV_3B64 & CC_0780

  Please I need an accurate model of the PCI communications controller driver

  Hello

  It's a system driver wise called "Intel Management Engine Interface (MEI) ' as mentioned in the following link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-83746-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5040732 & sw_lang =

  Please download the exe on the link above and install on your machine.

  Kind regards.

• Satellite L30-114 - need driver for the SM bus controller and sound

  Hi, friends

  Please I need your help on my Satellite L30-114. Am having problems with the sound and the SM bus controller, even I downloaded the audio driver and install it, from my camera, sound manager isn't sick, he always tells me my device is not functioning properly? Please I need some help here.

  Secondly, my SM bus controller is sick there the cormer sign please how can I rectify even that my wireless works fine.
  Only the controller sm bus and its giving problems.

  Thank you waiting for your answers.

  Newton

  Hello

  It would be interesting to know what OS you are using.

  By the way: you can find all the drivers here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

• How to make the button to set the properties of auto-scale one of the Axes on the graphical indicator so I can turn on or off when I press on it. In the Labview web UI designer

  How to make the button to set the properties of auto-scale one of the Axes on the graphical indicator so I can turn on or off when I press on it.

  I need to change the adjustment vaguely Autoscale property for my graphic indicator. Can someone help me please.

  Thank you!

  Hello

  I have confirmed that there is currently no way programmatically enable/disable autoscaling for axes on the LabVIEW graphical indicator generator of the user Web interface. We noted this to possibly be implemented in the future; Sorry for the inconvenience.

• The USRP CSD requires the LabVIEW Communications?

  I recently installed LabVIEW 2013 on my machine, as well as a whole bunch of toolboxes:

  LabVIEW English 2013
  VI Package Manager
  Module LabVIEW Control Design and Simulation 2013
  2013 LabVIEW Datalogging and Supervisory Control Module
  2013 LabVIEW MathScript RT Module
  NI LabVIEW 2013 LEGO (R) MINDSTORMS (R) NXT Module (in English)
  Module OR Vision Development 2013
  Module LabVIEW FPGA of 2013 (English)
  Xilinx toolchain 14.4
  Module time real LabVIEW 2013 (English)
  2013 LabVIEW Touch Panel module
  2013 LabVIEW Robotics module
  Software OR SignalExpress 2013
  LabVIEW Sound and Vibration Measurement Suite 2013
  Module LabVIEW Statechart of the 2013
  LabVIEW 2013 for myRIO Module
  Toolkit OR run real time Trace 2013
  2013 LabVIEW System Identification Toolkit
  LabVIEW Toolkit 2013 Digital Filter Design
  4.3.4 for LabVIEW Modulation Toolkit
  2013 LabVIEW VI Analyzer Toolkit
  2013 LabVIEW Database Connectivity Toolkit
  2013 LabVIEW Report Generation Toolkit for Microsoft Office
  LabVIEW Spectral Measurements Toolkit 2.6.4
  2013 LabVIEW Advanced signal processing Toolkit
  LabVIEW 2013 PID and Fuzzy Logic Toolkit
  Kit filter LabVIEW Adaptive, 2013
  Toolkit LabVIEW DataFinder of the 2013
  2013 LabVIEW Desktop Execution Trace Toolkit
  LabVIEW 2013 Multicore analysis and matrices hollow Toolkit
  LabVIEW 2013 power electric Suite
  Toolkit LabVIEW 2013 GPU analysis
  Biomedical Toolkit LabVIEW 2013
  Module LabVIEW 2013 OR SoftMotion
  NEITHER Motion Assistant 2013
  NEITHER Vision Builder for Automated Inspection 2012 SP1
  OR DIAdem Professional 2012 SP1 (English)
  LabWindows/CVI 2013 development system
  Module time real LabWindows/CVI 2013
  LabWindows/CVI Spectral Measurements Toolkit 2.6.4
  Spectral measures of LabWindows/CVI DURATION 2.6.4
  LabWindows/CVI SQL Toolkit 2.2
  Toolkit for processing Signal of LabWindows/CVI 7.0.2
  LabWindows/CVI PID Control Toolkit 2.1
  Execution of LabWindows/CVI Profiler 1.0
  Measurement Studio Enterprise Edition for Visual Studio 2012 2013
  General safety NI Patch 2nd quarter of 2013
  NEITHER TestStand 2013
  NEITHER ELVISmx 4.5
  NOR-DAQmx 9.7.5
  Xilinx 10.1 Compilation tools (requires the build tools additional Xilinx DVD)
  Device drivers or - February 2013

  I tried to follow this tutorial with the USRP 2932, coming soon, but I found out later that I have seem to have none of the LabVIEW Communications. No not those who prevent me from using the USRP radio? If not, then is there any restrictions on what I can do with the radio without communication?

  Hi BreadLB,

  The link to the tutorial you posted is based on LabVIEW Communications System Design Suite, a new software environment designed to accelerate the prototyping of the algorithm and stable air.  It is a completely separate and independent of LabVIEW environment.  See my post here for more details.  You can also download a free 30 day trial copy here.  Your hardware is supported with LabVIEW and LabVIEW Communications.

  The 2932 NOR is a network based USRP, and there a small on-board FPGA.  For this reason, the FPGA on that specific product is not a target of LabVIEW FPGA.  The NI 294 x / 5 x family has a large Kintex 7 FPGA and can be programmed using LabVIEW FPGA and LabVIEW Communications, as in the tutorial you posted.  The 2932 OR can be used with your host PC and LabVIEW for a variety of applications.  Unfortunately the tutorial that you have linked to your post requires the NI 294 x / 5 x hardware and Communications of LabVIEW.  If you have questions about a specific application for your 2932, please post more details and we would be happy to help you.

• Change the language of the LabView controls?

  I just need confirmation. If LabView controls, as a graph, have a context menu, then this menu will be first in the language of the LabView IDE, it is used with. If I create a new application, then the manufacturer includes the LabView RTE. It will also be the same language as the IDE version.

  Now, if I wanted to change the language of the context menu we will say to the french, it would be sufficient for the user has just installed a version in french of the RTE? Is this correct?

  AJMAL says:
  This will be useful?

  Yes, thanks. Another regional setting of RTE would replace the one we provide in our Installer and then the user would have the menu in its language. Very well!

• SD LabVIEW ARM storage limit

  What is the size limit for storage SD card on the plateau of MCB2300 ARM?  I want to use this forum, but you need to know the storage capacity before buying hardware and software.  I would use a 8GB card, but I'm guessing that maybe it's not possible.

  Hello

  ARM targets use the RL-ARM flash file system.  However, it seems all only 4 GB max.

  With the Flash file system, you can also write and read files on the standard SD (Secure Digital) and memory cards Flash MMC (Multi Media Card). They are used in SPI mode. Sizes of standard device of a little MB up to 4 GB are supported. Files on the memory card reader are stored in the standard FAT12, FAT16 or FAT32 file format.

  http://Keil.Asia/support/man/docs/rlarm/rlarm_fs_flashfs.htm

• 2013 LabVIEW allows the user to return to the LabVIEW 2012 or 2011?

  Hi all

  I have LabVIEW 2013. I noticed that in LabVIEW measurement and Automation Explorer (MAX) under the LabVIEW Run-Time 2012 SP1 f2 software is listed. This somehow means I can return or switch between LabVIEW 2013 and 2012 without having to install/reinstall?

  The reason why I ask, is that I have several instrument drivers written for LabVIEW 2012 sp1 I want to use.

  This is probably a silly question, I know.

  On a related note, is it possible to tell if a driver written for an older version of LabVIEW will work in a new version of LabVIEW? Or you just have to play with the software?

  Thank you

  Oh, John

  Hi John,.

  More explicitly answer your main question - you can install multiple versions of LabVIEW in parallel (at the same time, on the same PC), however that one version of patch of each major version (for example, 2011, 2012, 2013) can be installed - you can not install 2012 and 2012 SP1 at the same time.

  The runtime that you noticed has probably been installed with another component that was built in this environment.

  As Dennis said, the big thing to keep in mind is that your screws will have to be upconvertis/resized when moving between versions.

  If your instrument driver is written in 2012 LabVIEW using the serial at low altitude of LabVIEW drivers, it will certainly work in 2013.  If you open the screw driver in 2013 and that you do not see workload issues, you should be good to go.  If pilots request DLL or another have external dependencies can be involved more work.

  Kind regards

• LabVIEW FPGA: An internal software error in the LabVIEW FPGA Module has Unknown

  Sir/Madam,

  Note Labview 2012 SP1 installed about 2 weeks ago.,.

  Accident occurred during the compilation of an fpga vi who worked satisfactorally in the past.

  When I restarted and went to the message recomplile "LabVIEW FPGA: an internal software error in the LabVIEW FPGA Module" see attached picture of popup.

  I reinstalled Labview in its entirety and backed out the changes I made to the vi but still get the same message.

  Thanks in advance

  Daryl

  It turns out that the question was in the VI and not of LabView FPGA module as the message may indicate. I created a vacuum vi, cut and pasted items in this from the vi error and recompiled and it ran very well.

  Somehow the vi has been corrupted internally.

  Thank you it's fixed.

• Any camera regardless of the interface is available for use with the LabView interface.

  Hello

  I intend to go for some CMOS camera,

  but I have a huge doubt before buying, the camera of menttioned above is not anywhere in this list. Nor can I see any type being supported USB device.

  The question is

  1. is a camera regardless of the interface is available for use with the LabView interface?
  2. Can I build a VI to communicate with any device image and recording of camera and take the data?

  Any kind of help or advice is greatly appreciated... I have to buy a CMOS camera and begin to run.

  Thank you...

  Hello Virginia,.

  I am pleased that this information has been useful, one thing I wanted to mention is that USB 3.0 has its own standard USB 3.0 Vision which is currently not supported. If this camera is also Direct Show compatible then you will be able to acquire an image using IMAQdx and manipulate all the attributes that are published to the API Live Show.

  I hope that USB 3.0 Vision will be supported in the near future, and we tentatively announced for this standard of communication for the August 2013 Vision Acquisition Softwareupdate.

  See you soon,.

  -Joel

• Install the LabVIEW DSP Module on Labview 2009 Professional

  I have LabVIEW 2009 professional and I try to install the LabVIEW DSP Module on it. I have LabVIEW DSP Module 8.6, and I think that this is the final version. However, when I tried to install it, it says you should have LabVIEW 8.6 on your system.

  What should I do?

  Hello Brandon,.

  I did run the LabVIEW 8.6 DSP module, you must have LabVIEW 8.6 (compatibility table), which can be installed and run in parallel with LabVIEW 2009. I apologize for the inconvenience, but 8.6 is the latest version of this module, so you'll need to buy LabVIEW 8.6 for use.

  Kind regards

  Deborah Y.

• A query on the LabVIEW runtime engine.

  Can I access front of LabVIEW through Internet Explorer even if I do not have LabVIEW installed in my computer?

  The LabVIEW runtime engine works in this situation without the help of LabVIEW software?

  > Can I access front of LabVIEW through Internet Explorer, even if I do not have LabVIEW installed in my computer?

  Yes

  Server must have the labview, labview Web Server runtime and should be run remotely front panels.

  > LabVIEW runtime engine works in this situation without the help of LabVIEW software?

  Does not understand the question.

  Engine run LabVIEW is a LabVIEW software, which is required to run files executable labview. In the case of remote façade panels screws (exe) running on the server that has the run-time engine. Page Web you are viewing in the browser (client) gives you a picture and monitors where you click on it. It passes those clicks to the server, it changes picture accordingly (going on those clicks for labview, gets the update of this photo). Customer does not screw, so should not be the runtime of LV.